Gebruiksaanwijzing /service van het product 7 van de fabrikant Krell Industries
Ga naar pagina of 22
Instructions for Use Owner ’ s Reference THE LEADER IN AUDIO ENGINEERING Showcase 7 Showcase 6 Showcase 5 Multi channel Amplifier.
© 2002 by Krell Industries, Inc. All rights reserved P/N 306039 This product is manufactured in the United States of America. Krell ® is a registered trademark of Krell Industries, Inc., and is restricted for use by Krell Industries, Inc., its subsidiaries, and authorized agents.
Contents Krell Showcase Amplifier iii INTRODUCTION 1 DEFINITION OF TERMS 2 UNP ACKING 3 PLACEMENT 4 AC Power Guidelines 4 FRONT P ANEL DESCRIPTION 6 BACK P ANEL DESCRIPTION 8 CONNECTING THE SHOWCASE A.
iv Krell Showcase Amplifier FIGURE 1 The Showcase Amplifier Front Panel 5 FIGURE 2 The Showcase Amplifier Back Panel 7 Illustrations Page.
Krell Showcase Amplifier 1 Thank you for your purchase of a Krell Showcase Amplifier . The Showcase Amplifier is a flexible design that delivers five, six, or seven channels of amplification. All three configurations include input and output connections for all seven channels.
2 Krell Showcase Amplifier Following are the definitions of key terms used in your owner ’s ref- erence manual. Balanced A symmetrical input or output circuit that has equal impedance from both input terminals to a common ground reference point.
Unpacking Krell Showcase Amplifier 3 1. Open the shipping box, and remove the top layer of foam. The following items are visible: 1 Showcase Amplifier 1 Accessory Kit containing: 1 AC power cord 1 12 .
4 Krell Showcase Amplifier Before you integrate the Showcase Amplifier into your system, review the following guidelines to choose the location for the com- ponent.
1 Power Button 2 Stand-by LED 3 Power LED SHO WCASE AMPLIFIER 2 1 3 STAND-BY POWER Figure 1 The Showcase Amplifier Front Panel.
The Showcase Amplifier front panel provides power on and indi- cates operating status. 1 Power Button Use this button to switch the Showcase Amplifier power between the stand-by and the operational modes and also to switch the 12 VDC output (12 V trigger) on and off.
6 4 5 7 8 9 OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 INPUT 6 INPUT 7 Showcase Multi-channel Amplifier KRELL INDUSTRIES, INC. 45 CONNAIR ROAD ORANGE, CT 06477-3650 USA 50/60 Hz MADE IN USA 30mA max.
Back Panel Description See Figure 2 on page 7 8 Krell Showcase Amplifier The Showcase Amplifier back panel provides connections for all inputs and outputs, remote connection input and output links, and the AC power supply . 4 Inputs 1-7 The Showcase Amplifier has seven channel inputs for output devices with balanced XLR connectors.
Krell Showcase Amplifier 9 Back Panel Description, continued 8 12 VDC Remote Power In The Showcase Amplifier is equipped with an input that receives 12 VDC power on/off (12 V trigger) signals from other Krell compo- nents and other devices that incorporate a 12 V trigger .
Connecting the Showcase Amplifier to Y our System 10 Krell Showcase Amplifier The Showcase Amplifier is equipped with balanced and single-ended inputs.
Connecting the Showcase Amplifier , continued Krell Showcase Amplifier 11 4. Connect the loudspeaker cables to the Showcase Amplifier channel output binding posts (6) located on the back panel. The Showcase 5 uses only outputs 1-5 and has caps on the speaker binding posts for channels 6 and 7.
Amplifier Operation 12 Krell Showcase Amplifier When powering up your system, turn the amplifiers on last. When powering down your system, turn amplifiers off first. The proce- dures for amplifier operation follow . 1. Plug the end of the AC power cord into the AC wall outlet.
T roubleshooting System Noise Krell Showcase Amplifier 13 When you mix and match high-performance audio components, each with its own ground potential, a low frequency hum may occur in one or all loudspeakers. If this happens when you place the Showcase Amplifier into your system, follow these simple trou- bleshooting steps: 1.
Questions and Answers 14 Krell Showcase Amplifier Q. Should I turn the Showcase Amplifier off (unplug the amplifier) when not playing music? A. No. Leave the Showcase Amplifier in the stand-by mode when not playing music. The stand-by mode avoids cold starts as well as minimizes heat output and power consumption.
T o register your product for warranty benefits, please complete and return the Warranty Registration Card enclosed in the shipping box within 15 days of purchase. Thank you. This Krell product has a limited warranty of five years for parts and labor on circuitry .
16 Krell Showcase Amplifier Return Authorization Procedure If you believe there is a problem with your component, please con- tact your dealer , distributor , or the Krell factory to discuss the problem before you return the component for repair .
Krell Showcase Amplifier 17 Specifications Showcase 7, Showcase 6, Showcase 5 Showcase 7 Showcase 6 Showcase 5 FREQUENCY RESPONSE 20 Hz to 20 kHz 20 Hz to 20 kHz 20 Hz to 20 kHz +0 dB, -0.15 dB +0 dB, -0.15 dB +0 dB, -0.15 dB .2 Hz to 95 kHz .2 Hz to 95 kHz .
Krell Industries, Inc. 45 Connair Road Orange, CT 06477-3650 USA TEL 203-799-9954 F AX 203-891-2028 E-MAIL krell@krellonline.com WEBSITE http://www .krellonline.
Een belangrijk punt na aankoop van elk apparaat Krell Industries 7 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Krell Industries 7 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Krell Industries 7 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Krell Industries 7 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Krell Industries 7 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Krell Industries 7 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Krell Industries 7 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Krell Industries 7 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
