Gebruiksaanwijzing /service van het product FS-5900C van de fabrikant Kyocera
Ga naar pagina of 132
.
i Thank you for purchasing the K yocera FS-5900C Colour Laser Printer . Notice NO LIABILITY IS ASSUMED FOR ANY DAMAGE CA USED BY IMPROPER INSTALLA TION . The information in this manual is subject to change without notification. Additional pages may be inserted in future editions.
ii 2. Copy Restrictions FONTW ARE/TrueDoc is copyrighted. Unauthorized copying of FONTW ARE/TrueDoc even if modified, merged, or included with other softw are, is expressly forbidden. Y ou may be held legally responsible for any copyright in- fringement.
iii IMPOR T ANT SAFEGUARDS 1. Read all of these instructions and save these instructions for later use . 2. Unplug this product from the wall outlet before c leaning. 3. Do not use this product near w ater . 4. Do not place this product on an unstable cart, stand, or table .
iv CE Marking Dir ective according to Council Directive 89/336/EEC and 73/23/EEC Manufacturer’ s name: Kyocera Corporation, Printer Division Manufacturer’ s address: 2-14-9 T amagawadai, Setagaya .
v Declaration of Conformity (Australia) Manufacturer’ s name: Kyocera Corporation, Printer Division Manufacturer’ s address: 2-14-9 T amagawadai, Setagaya W ard, T okyo 158-8610, J apan declares t.
vi ENERGY ST AR SM As an ENERGY STAR Partner , K yocera Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency . The basic objective of the ENERGY STAR Program is to reduce environmental pollution by encouraging the manufacture and sale of equipment that uses energy more efficiently .
vii Contents Chapter 2 Setup Chapter 1 Before Y ou Star t Chapter 3 Using the Printer Cautions ........................................................................................... 1 Features .....................................................
viii Contents Chapter 4 Care and Maintenance Appendix Cleaning ......................................................................................... 64 User Replaceable Components ................................................... 69 Clearing a Jam .
ix For Y our Safety General W arning To prevent fire or shock hazard, do not expose this product to rain or any type of moisture. Caution Do not open covers and do not attempt to repair the unit yourself. Refer servicing to qualified personnel. P ower Sour ce W arning • The power source voltage of this unit is listed on the nameplate.
x For Y our Safety Mo ving the Unit The printer weighs approximately 51 kg (112 lbs.). It must be handled by two people. Turn the power off and remove the power cord when handling the unit.
xi For Y our Safety Caution Labels ATTENTION: SURFACE CHAUDE CI-INTERIEUR VORSICHT: HEISSE FLÄCHE INTERN ATENCION: SUPERFICIE CALIENTE EN EL INTERNO CAUTION: HOT SURFACE INSIDE CAUTION: HOT SURFACE B.
xii For Y our Safety FOR USERS IN THE UK IMPORTANT: FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY This printer is supplied with a moulded three pin mains plug each for your safety and convenience.
1 Bef ore Y ou Star t Cautions To avoid machine malfunction, do not use the equipment under the following conditions: • Direct exposure to sunlight • Extremely high or low temperature [temperature range: 10˚C to 32.
2 Bef ore Y ou Star t ■ CD-R OM To prevent the CD-ROM from accidental damages: • Do not touch or write on the surface of the disc. • Do not leave the disc out of the protective case. • Do not leave the disc in direct sunlight or near heat sources.
3 Bef ore Y ou Star t Features The FS-5900C Colour Laser Printer provides fast, high-quality colour printing on plain paper, plus the ease of operation and high performance you expect from a laser printer.
4 Bef ore Y ou Star t System Requirements PC To operate the FS-5900C effectively, refer to the following: CPU: More than Pentium (133 MHz or faster CPU is recommended.) Operating System: Windows 3.1 *1 / Windows 95 *2 / Windows 98 *3 Windows NT *4 RAM: 16 MB or more (More than 32 MB is recommended.
5 Bef ore Y ou Star t Minim um Space Requirements P ower Sour ce • The voltage level of the power source must not vary more than ±10% from the voltage level marked on the nameplate (located on the back of the unit). • Do not use an extension cord.
6 Bef ore Y ou Star t Unpac king Make sure that all of the items shown below were provided and have not been damaged. Report damage or shortages to the reseller from which the unit was purchased. Note: Save the original carton and packing materials for future shipping and transporting of the unit.
7 Bef ore Y ou Star t P ar t Names ■ Fr ont side view ■ Rear side vie w Power switch ( ☞ P. 25) Network interface card slot Multi-purpose (MP) tray ( ☞ P. 19) Left side cover ( ☞ P. 19) Media thickness switch* ( ☞ P. 19) Parallel interface connector ( ☞ P.
8 Bef ore Y ou Star t Ready PAR 600 A4 001 Contr ol Panel Overvie w Message Displa y The message display displays the printer’s operational mode. Messages which are displayed and their meanings are given in the table below. Message Meaning Self test The printer is self-testing after power-up and is not ready to print.
9 Bef ore Y ou Star t Interface Indicator The interface indicator indicates the interface over which data is currently being received or was last received.
10 Bef ore Y ou Star t ON LINE DATA Symbolic Indicator This printer icon includes the indicators which show the following information regarding the printer’s paper and toner status. Name Description Face-down indicator Indicates when printed pages are delivered to the output tray in the face-down stack (correct order).
11 Bef ore Y ou Star t Contr ol K eys Key Function ON LINE This key toggles the printer on-line and off-line. CANCEL This key cancels the data processed in the printer during print- ing. When the printer is in a mode selection sequence (See MODE key below), pressing this key abandons mode selection in course.
12 Setup Setting Up the Printer Preparing the Ima ging Unit 1 Open the front cover . 2 Turn the upper green lever cloc kwise until it stops and the arrows are aligned. (This tightens the internal belts , ensuring the unit is ready for printing .) 3 Close the front cover .
13 Setup Setting Up the Output T ra y 1 Remove the adhesive tape that holds the output tray against the printer . 2 Lower the tray to the operating position.
14 Setup Installing the T oner Developer s Note: The toner developers that are shipped with the printer are starter developers. They are installed in exactly the same manner as the optional developers; the only difference is that the starter developers have less toner.
15 Setup 4 Insert the toner developer in the appropriately labelled slot. From top to bottom, the order of the colour toner developers is BLACK, CYAN, MAGENTA, YELLOW. Caution: Excessive exposure to light will damage the imaging unit; do not leave the right side door open for more than 1 minute.
16 Setup Loading Media Loading P aper or T ransparencies in the Media Cassette The printer is shipped with a media cassette (either Letter paper or A4 paper) installed. The printer can also use five different trays as options: Cassette Size A4 Paper 210 mm × 297 mm A4 Transparency 210 mm × 297 mm Letter Paper 8.
17 Setup 2 Remove the base plate stopper from inside the media cassette; refer to the instruction sheet attached to the cassette . 3 Push down on the metal plate until it clicks , loc king it in place. 4 F an the media (paper/transparencies), then tap it on a level surface to avoid media jams or skewed printing .
18 Setup 5 Place the media in the cassette under the hooks . The height of media should not exceed the limit mark on the cassette, or it may cause a jam. Notes: • Load media with the print side down. Most media has instructions recommending the side to be printed first.
19 Setup Thin Middle Thick (1) Loading Media in the Multi-purpose T ray The multi-purpose (MP) tray serves as an additional tray for loading any type of media that ranges in size from 91 mm × 254 mm to 216 mm × 356 mm (3.6 ≤ × 10 ≤ to 8.5 ≤ × 14 ≤ inches).
20 Setup ■ Loading P aper Notes: • Reusing media that has been fed through the printer (for example, after jams) can reduce the life of the consumables and paper path components. • When printing legal size using the multi-purpose tray, backside marking may occur.
21 Setup 5 Insert the media with the printing side up into the multi-purpose tray . The height of media should not exceed the limit mark on the left guide, or it may cause a media jam. 6 Adjust the media guides to the media size. 7 Use the printer driver to select the multi-purpose tray .
22 Setup ■ Loading Label For detailed information on labels, refer to page 114. 1 Set the media thickness switc h ( ☞ P . 19). 2 Adjust the media guides to the width of the label sheets .
23 Setup Connecting the Printer to a Computer The printer can directly be connected to a computer through the parallel interface or the serial interface. To connect the printer in a local area network, you must obtain a network interface card ( ☞ P.
24 Setup Using a P arallel Interface Cable If you do not have a parallel interface cable, you will need to purchase one from your local computer store or dealer ( ☞ P. 116 for Parallel Interface specifications). 1 Make sure the computer , printer and the other connected peripheral devices are turned off .
25 Setup Connecting the Serial Interface To connect the printer to a computer using the serial interface, use the XSER connector at the rear panel of the printer. The serial connector is of a round, 8-pin DIN type and you will need a cable adaptor (SA-80) if you connect a DSub type serial connector.
26 Setup Printing a Status P age From the Printer Contr ol Panel The status page provides general information on printer settings and configuration. Make sure the printer is ready and paper is loaded. Use the following procedure to print a test page. While the message display indicates Ready , press the STATUS key.
27 Setup Installing the Driver Software The driver software installation will create the printer driver for Windows 3.1 or Windows 95/98. See the Help file provided with the driver for how to use the printer with the driver software. Installing the Printer Driver f or Windows 3.
28 Setup Installing the Printer Driver f or Windows 95/ Windo ws 98 ■ Using Plug and Pla y 1 Turn on the printer . 2 Turn on the computer and start Windows 95/W indows 98. The New Hardware Found window is displayed for a few seconds, then the Update Device Driver Wizard window is displayed.
29 Setup ■ Using Ad d Printer 1 Start Windows 95/Windows 98. 2 Quit all applications . 3 Click Start , move the pointer to Settings , then click Printers . The Printers window is displayed. 4 Double click the Add Printer icon. The Printer Wizard screen starts.
30 Setup Setting the Colour Density The printer panel provides an interface to adjust the density of the toner applied to the media. This makes it possible to offset changes in density that may result due to varying environmental conditions or aging of the toner or imaging unit.
31 Setup The current density setting for each colour is indicated by four stripes of cyan, magenta, yellow, and black (from left to right). On the Colour Calibration Page as shown in the following example. The factory default setting for each colour density is 10.
32 Setup 2 Compare the current colour density settings on the Colour Calibration P age with the colour density samples on the Colour Calibration Reference to see if they match. Place the Colour Calibration Page on at least 2 sheets of clean white paper in a well-lighted area.
33 Setup 4 Press the + or - key until >Print Calibration Page is indicated. 5 Press the ENTER key twice to reprint the Colour Calibration P age. • Repeat step 3 above, if necessary. 6 Repeat steps 3 through 5 for each colour (MAGENT A, YELLOW , BLACK).
34 Using the Printer Mode Selection This section explains the menu levels and options which can be set using the MODE key. The MODE key can be used to display all of the menus in the following table. > KPDL (AUTO) Emulation > KPDL Auto Option Normal On Landscape >Pitch 10.
35 Using the Printer Continued on next page Continued from previous page MEMORY CARD > >Read fonts >Read data >Write data >Delete data >Format >List of Partitions >RGB Simulati.
36 Using the Printer Ignore LF CR and LF >LF action LF only >Printer Reset Continued from previous page Ignore CR CR and LF >CR action CR only >MSG language English >List of >Print HEX-DUMP >Sleep timer 060 min >Form Feed Time out 030sec.
37 Using the Printer Na vigating thr ough the menus The menus are in the hierarchy as shown in the diagram above. Use the + and - keys to move between menus in the same level (“vertically” in the table). The + key shows the next menu, while the - key shows the previous one.
38 Using the Printer Outline f or Menus ■ Interface menu The Interface menu selects one of the three printer interfaces ( Option is available only if an option network interface card is installed) on which subsequent mode menu settings become effective.
39 Using the Printer ■ Number of copies The Number of copies menu sets the number of copies to be printed. Level 1 Range Number of copies 001 (Default) to 999 ■ Em ulation The Emulation menu switches the printer emulation. KPDL is the Kyocera’s implementation of the Adobe’s PostScript language.
40 Using the Printer 5 Press ENTER . 6 Press the + key repeatedly until the font name of Dutch801- RomanSWM is displayed. 7 Press ENTER to confirm the font selection.
41 Using the Printer Resident Scalable Fonts.
42 Using the Printer KPDL Fonts.
43 Using the Printer ■ P age orientation The Page orientation menu switches between portrait and landscape page orientations. Level 1 Range Page orientation Portrait (Default) Landscape ■ Option R OM The Option ROM menu reads data in the option ROM and prints a list of them as partitions .
44 Using the Printer ■ Memory card The MEMORY CARD menu reads, writes, and deletes data on the memory card. It also allows formatting the memory card and printing a list of the contents. This menu is available only when a memory card is inserted into the memory card slot at the back of the printer ( ☞ P.
45 Using the Printer ■ Colour calibration This menu provides an interface to adjust the density of the toner applied to the media. For details on how to calibrate toner density, see Setting the Colour Density ( ☞ P.
46 Using the Printer ■ P aper handling mode The Paper handling mode allows the MP tray to be configured in the same manner as with the media cassette.
47 Using the Printer Cassette mode Approximately 100 sheets of paper can be continuously fed. Note: In First mode, printing is carried out using custom size paper feed timing regardless of the MP tray size setting. MP tra y type When cassette is selected as the MP tray mode, the paper source is automatically selected according to the print data.
48 Using the Printer ■ Formfeed timeout time The Formfeed timeout time menu adjusts the time-out time for the occurrence of the printer’s formfeed action. Absence of data for this period of time causes a formfeed. Level 1 Level 2 Range Others Form feed time out 000 to 495 (seconds) Note: Any value from 0 to 495 [seconds] in 5-second increments.
49 Using the Printer ■ Printer Reset The Printer Reset menu brings all temporary printer settings back to their default values. Note that resetting the printer also removes all temporarily downloaded resources such as fonts and macros from its memory.
50 Using the Printer ■ Resour ce protection The Resource protection menu enables the resource protection function in the following options. The resource protection function preserves PCL resources in memory so that they are intact even when you change the emulation from KPDL (or KPDL [AUTO]) back to PCL 5C.
51 Using the Printer RAM DISK A RAM DISK can be set up as a virtual media device by setting a given amount of the total printer memory as the RAM DISK. This can then be used for reading and writing data just as with a memory card or as a virtual mail box function (see page 52 to 56).
52 Using the Printer ■ RAM DISK Operations The following operations are available with the RAM DISK. • Read Data • Write Data • Delete Data • Print a List of Data Names • Print Accumulated.
53 Using the Printer ■ Outputting to a VMB When sending data to a virtual output tray set within the RAM DISK, make this setting from the printer driver. With this setting, data can be sent by specifying the desired virtual output tray number. It is also possible to assign a name to a virtual output tray and send data by specifying that name.
54 Using the Printer ■ Print Accum ulated VMB Data with a P ass wor d This function prints VMB data protected by a password which has accumulated in a virtual output tray.
55 Using the Printer ■ Print VMB Accum ulated Data List This feature prints a list of VMB data accumulated in the RAM DISK. 1 Display >List of VMB . >List of VMB 2 Pressing the ENTER key will cause a ? to display . >List of VMB ? Press the CANCEL key if you want to halt printing .
56 Using the Printer ■ Operations f or Using a Bar code Reader If an optional barcode reader (BC-1) is connected to the printer, it is possible to print data within a virtual output tray using the barcode in the list.
57 Using the Printer Memory Car ds This printer is equipped with a memory card slot. If a JEIDA Ver. 4.2 memory card is used, it is possible to read, write and delete data, and format the memory card. Note: Only 32 MB or less, flash or S-RAM type memory cards, conforming to JEIDA Ver.
58 Using the Printer ■ Reading Data fr om a Memory Card The operation described here is performed while the message display reads Ready . 1 Insert the memory card into the memory card slot ( ☞ P . 57). 2 Bring up the menu >Read font on the message display .
59 Using the Printer 5 Check that the message displa y has changed to Waiting and press the FORM FEED key . The printer will automatically print the data just written (example below). This printout can be used to check the name (partition name) under which data was written and confirm that it was written properly.
60 Using the Printer ■ Formatting a Memory Car d It is necessary to first format a new memory card before it can be used by the printer. Formatted memory cards can then be written with data. Note: • Note that if you format a memory card which already has data written on it, that data will be lost entirely.
61 Using the Printer ■ Memory Car d Err or Codes Error codes 11, 13, 17, and 18 apply only to flash memory cards. Error code Meaning MEMORYCARD err 01 • You attempted to write more than 32 MB of data to a Press CONTINUE memory card. Or, the capacity of the memory card installed in the printer is more than 32 MB.
62 Using the Printer Setting the Sleep Timer The sleep timer can be set anywhere from 0 to 120 minutes in 5-minute increments. Setting the sleep timer to 0 turns it off. The sleep timer is set at the factory to 60 minutes. T o set the sleep timer: 1 Press the MODE key on the printer panel.
63 Using the Printer Permanent In this mode, the printer stores fonts, macros, symbol sets, etc. in memory that were downloaded as permanent PCL resources. All temporary resources are lost when the emulation mode is changed from PCL 5C to KPDL or vice versa.
64 Care and Maintenance Cleaning Periodic cleaning of the printer is recommended. The frequency of cleaning is dependent upon the environment in which the printer is used. You should clean the printer: •␣ At least once a month. •␣ When the printer experiences frequent media jams.
65 Care and Maintenance 4 Gently rotate the paper -pick rollers 180° (the paper -pick rollers are D-shaped) and wipe them with a lint-free cloth that has been moistened with isopropyl alcohol. 5 Reinsert the paper feeder ( (1) ) and close the left side cover ( (2) ).
66 Care and Maintenance When using the duplex unit, it may become necessary to clean the rollers inside the unit. Open the internal cover, and wipe the rollers with a lint-free cloth steeped in isopropyl alcohol. Cleaning the home sensor 1 Open the printer’ s front cover .
67 Care and Maintenance (3) Grasping the front green handle , slide the imaging unit out until it catches . (4) Lift up the left green handle . Pull the imaging unit out of the printer and cover it to protect it from light exposure . Important: Do not touch the green surface (the right side) or the black belt (the underside).
68 Care and Maintenance 3 Use a dry , lint-free c loth to wipe the slot of the sensor . 4 Reinsert the imaging unit into the printer , holding it by its green handles . Match the arrow on the right side of the imaging unit with the arrow on the printer, and slightly push the imaging unit into the printer.
69 Care and Maintenance User Replaceable Components When the printer panel indicates that a supply needs to be replaced, make sure that you have replacement supplies on hand. The printer may continue to print until the supply is completely used up; then it stops until you replace the indicated supply.
70 Care and Maintenance Main Charger Printer panel message Average life Fuser unit * 57,000 pages (with pre-installed Oil Warning FK-81 Supply Roll and Cleaning Pad) Fuser KIT Fuser unit must soon be replaced. 60,000 pages Replace FK-81 Fuser KIT Fuser unit must now be replaced.
71 Care and Maintenance Clearing a Jam ■ Clearing a media jam Make sure that you follow these guidelines to avoid frequent media jams: • Always use high-quality plain paper and transparencies.
72 Care and Maintenance ■ Jam at A 1 Open the left side cover corresponding to the selected media cassette. 2 Remove the jammed media. 3 Close the left side cover . — OR — 4 Remove the media cassette or duplex unit. 5 Remove the jammed media from inside the printer .
73 Care and Maintenance ■ Jam at B 1 Open the left side cover . 2 Use the green handles to pull out the paper feeder . 3 Remove the jammed media on the paper feeder .
74 Care and Maintenance ■ Jam at C 1 Remove the fuser: (1) Open the printer front cover . (2) Turn the small green thumbscrew counterclockwise to unlock the fuser . Safety Caution: • The fuser is hot. To avoid personal injury, turn off the printer and wait 10 minutes (after opening the front cover) for the fuser to cool before touching it.
75 Care and Maintenance 2 (1) Hold the fuser as shown below , and slide it out of the printer . Safety Caution: The fuser unit weighs approximately 3.1 kg (6.8 lbs.). Take care when handling it. (2) Close the front cover . 3 Remove the oil supply roll: (1) Press out on tabs to unlock the oil supply roll.
76 Care and Maintenance 4 (1) Turn the fuser’ s large green knob clockwise . (2) Remove the jammed media. 5 (1) Replace the oil supply roll into the fuser . (2) Press down firmly on the oil supply roll to snap both sides into place. Caution: If the oil supply roll is not installed correctly, print quality will be diminished.
77 Care and Maintenance 7 (1) Turn the small green thumbscrew clockwise to lock the fuser . (2) Close the front cover . (1) (2).
78 Care and Maintenance ■ Jam at D Safety Caution: The fuser is hot. To avoid personal injury, turn off the printer and wait 10 minutes (after opening the front cover) for the fuser to cool before touching it. Note: First check the exit opening for media that has jammed and folded like an accordion.
79 Care and Maintenance 1 B (Printing face down) (1) Open the front cover . (2) Pull open the access door (above the plastic output tray). See if the media is visible . (3) Turn the large green knob on the fuser counterclockwise . (4) Remove the media from inside the access door .
80 Care and Maintenance ■ Jam at E 1 Remove the jammed media from the output tray . — OR — Pull open the access door (above the plastic output tray) and remove the media. Safety Caution: Be careful not to let go of the access door while it is opened.
81 Care and Maintenance ■ Jam at F 1 Remove the jammed media from the multi-purpose tray . 2 Open and close the front cover to clear the error message from the message display .
82 Care and Maintenance ■ Jam at G 1 (1) Pull open the access door (above the plastic output tray), and look for any paper . (2) Remove the media from inside the access door . Safety Caution: Be careful not to let go of the access door while it is opened.
83 Care and Maintenance (4) Remove the jammed media from the duplex unit. 2 Open and close the front cover to clear the error message from the message display .
84 Care and Maintenance ■ Jam at H 1 Open the lower left side cover . 2 Remove the jammed media. 3 Close the lower left side cover . — OR — 4 Remove the selected media cassette (middle or lower media tray). 5 Remove the jammed media from inside the printer .
85 Care and Maintenance T roub leshooting Trouble Possible Cause Corrective Action A single colour is not uniform or many vertical streaks (both light and dark) of slightly differ- ent density and non- uniform colour. The toner is almost depleted. Replace the colour toner developer.
86 Care and Maintenance A single colour has a sharp, dark or light vertical streak. Trouble Possible Cause Corrective Action The toner developer is almost depleted and is not properly applying toner. Replace the colour toner developer. Small white spots appear on OHP trans- parency.
87 Care and Maintenance Trouble Possible Cause Corrective Action Straight, thin light vertical line in colours. The photosensitive belt inside the imaging unit is scratched. Replace the imaging unit. Each colour “bleeds” into the colour band. The imaging unit’s internal waste toner box is full.
88 Care and Maintenance Trouble Possible Cause Corrective Action One or more dark vertical lines appear on the print in all colours. The imaging unit is scratched. Replace the imaging unit; make sure that the old imaging unit is not exposed to light for more than 45 seconds.
89 Care and Maintenance Trouble Possible Cause Corrective Action Dark and wavy vertical streaks appear in all colours. The main charge grid is dirty. Replace the imaging unit. The entire page prints in black, including the borders. Bad electrical contact for the main charge grid.
90 Care and Maintenance ■ If y ou can’t make a print Trouble Possible Cause Corrective Action The page is completely blank. The problem could be with one of the following: • Engine control board. • Developer voltage. • Laser scanning unit mirror.
91 Care and Maintenance ■ Media pr oblems Trouble Possible Cause Frequent paper-picking errors Fan the paper or transparencies before installing them in their respective cassettes; this is especially important for transparencies because they tend to stick together.
92 Care and Maintenance ■ Print quality pr oblems Trouble Corrective Action Prints have dull, faded colours. Print the Colour Calibration Page from the Colour Calibra- tion menu in the printer panel. Check the density settings for each colour and compare them to the examples on the Colour Calibration Reference card.
93 Care and Maintenance Err or Messa ges Printer P anel Message Error Message Possible Cause Corrective Action Add paper ( paper source) (paper size)(media type) The paper source is out of paper. Add paper to the paper cas- sette or multi-purpose tray.
94 Care and Maintenance Error Message Possible Cause Corrective Action I/F occupied The front control panel operation you attempted is not possible because that interface is receiving data. Wait until the data transfer is completed on that interface. Imaging unit not locked The imaging unit is not locked properly because its lever is not lifted.
95 Care and Maintenance Error Message Possible Cause Corrective Action Load cassette # (paper size) (media type) The paper size does not match. The size of paper panel in the cassette is different to the size specified by the application software or by PRESCRIBE 2e command.
96 Care and Maintenance Error Message Possible Cause Corrective Action Missing Toner TD-81Y (Yellow) The yellow toner develop- er is not installed in the printer. Install the yellow toner developer ( ☞ P. 14). Missing paper feed unit The paper feeder unit is not installed in the printer.
97 Care and Maintenance Error Message Possible Cause Corrective Action RAM DISK error ## Press CONTINUE Check the error code displayed in the place of ## and refer to the corresponding description at right. 01: Abnormal format. Try turning the power off and on again.
98 Care and Maintenance Error Message Possible Cause Corrective Action 99: MPS: No job in the virtual bin specified for output or that page is missing. Read font ? Failed A font could not be read due to insufficient memo- ry. Read macro ? Failed A macro could not be read due to insufficient memory.
99 Care and Maintenance Error Message Possible Cause Corrective Action Toner low TD-81C (Cyan) The cyan toner developer is almost empty. Replace the cyan toner devel- oper as soon as possible. Toner low TD-81K (Black) The black toner developer is almost empty.
100 Care and Maintenance ■ Hard Disk Err or Codes Error Message Remedy HARDDISK error## Check the error code (digits) shown at the ## position, and Press CONTINUE refer to the following. 01: Format error. The hard disk has malfunctioned. Turn on the printer again.
101 Care and Maintenance Code Error Meaning 24 unmatchedmark Expected mark not found on stack 25 unregister Internal error 26 vmerror Virtual memory is exhausted, or illegal access was attempted 27 ba.
102 Care and Maintenance 1 Turn off the printer; remove the power cord and all interface cables. 2 Remove the media cassette from the printer; remove the media from the cassette(s). 3 Press down on a media cassette’ s metal plate. Place the base plate stopper into the media cassette.
103 Care and Maintenance 4 Reinsert the media cassette into the printer; use adhesive tape to secure the cassette to the printer . 5 If you have other media cassettes , repac k them for shipping or storage in their original shipping boxes . 6 (1) Open the printer’ s front cover .
104 Care and Maintenance 8 Wrap the imaging unit with a protective black plastic sheet. Caution: Do not expose the imaging unit to light for more than 45 seconds to avoid damage. 9 On the imaging unit, turn the upper lever 90° counterclockwise; this is necessary to protect the imaging unit during shipment.
105 Care and Maintenance 12 (1) Push in on green tabs to unlock the cover . (2) Raise the cover until it catches in the open position. 13 (1) Rotate the transfer unit’ s green handles up. (2) Lift out the transfer unit. 14 Place the transfer unit on newspaper or drop cloth.
106 Care and Maintenance 15 Install the plastic cover and insert the transfer unit into a plastic bag and seal the end tightly . Install the transfer unit into the packaging . Note: Use the plastic cover that is originally fitted with a new TR-81 transfer unit.
107 Care and Maintenance (3) Replace the shipping cover . (4) Secure the shipping cover with adhesive tape . (5) Insert each toner developer into a plastic bag and seal the end of the bag tightly . (6) Repeat instructions (2) to (5) for each toner developer .
108 Care and Maintenance 18 (1) Raise the output tray and secure it to the printer with adhesive tape . (2) Secure the front cover , the multi-purpose tray and the left side cover to the printer with adhesive tape . If you don’t have an option Paper Feeder, go to step 20.
109 Care and Maintenance 21 Repack the printer in the original shipping box. Refer to the diagram below . Make sure that you keep the printer upright and level when moving.
110 Appendix Specifications Printer Power source Refer to the nameplate on the rear of the unit. Temperature Operating: 10°C to 32.5°C (50°F to 90.5°F) Recommended Operating: 16°C to 27°C (60°F.
111 Appendix Maximum printing speed The print speeds listed in the following table represent the time the printer produces multiple prints on various media and resolution (Continuous throughput rate) .
112 Appendix Mar gins and Print Area When the image is printed on the media, the image (print area) is a bit smaller than the media size. You may need to adjust the page margins in the application software to match the print area.
113 Appendix ■ P aper Weight The printer is designed to work well with most types of paper. However, differences in paper may have significant effects on the quality of the print or the reliability of paper handling. It is strongly recommended that you always test paper before purchasing it to make sure it provides desirable performance.
114 Appendix ■ T ransparencies and Labels You may also print on transparencies and labels that are made for the printer. The following work satisfactorily.
115 Appendix • Re-using transparencies that have been fed through the printer once (for example, after jams or if the transparency is ejected without being printed) can reduce the life of the consumables and paper path components. • With any label stock, the labels must completely cover the backing material.
116 Appendix Bi-directional P arallel Interface The bi-directional parallel interface is based on the IEEE1284 standard. If your computer has a bi-directional parallel port, the printer driver and printer can take advantage of faster data transfer. Specifications Connector Type IEEE1284 type connector Cable Use a shielded cable 2 m (6.
117 Inde x A AC inlet ..................................................................... 7, 24 ATTENTION indicator ............................................ 8, 10 Audio alarm .................................................................. 50 Auto cassette mode .
118 Inde x Memory Card ................................................................ 57 Memory card ........................................................... 43, 44 Memory Card Error Codes .......................................... 61 Menus .....
119 Index V Virtual Mail Box (VMB) ............................................... 52 W W arnings ........................................................................ ix Windows 3.1 ................................................ 4, 27, 28, 115 Windows 95 .
Een belangrijk punt na aankoop van elk apparaat Kyocera FS-5900C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Kyocera FS-5900C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Kyocera FS-5900C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Kyocera FS-5900C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Kyocera FS-5900C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Kyocera FS-5900C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Kyocera FS-5900C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Kyocera FS-5900C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
