Gebruiksaanwijzing /service van het product Sp9000 van de fabrikant Leica
Ga naar pagina of 30
Instruction Manual Leica SP9000 V 2.2 English – 08/2007 Always keep this manual near the instrument. Read carefully prior to operating the instrument.
.
3 Leica SP9000 – Automatic knife sharpener The information, numerical data, notes and value judgments contained in this manual represent the current state of scientific knowledge and state- of-the-art technology as we understand it follow- ing thorough investigation in this field.
4 Instruction manual V 2.2 – 08/2007 Table of contents 1. Important Not es .............................................................................................................. 5 1. 1 Symbols used in this manual and their meaning ..........
5 Leica SP9000 – Automatic knife sharpener 1.1 Symbols used in this manual and Warnings appear in a grey box and are marked by a warning triangle: Useful notes, i.e. important user information appear in a grey box and are marked by an in- formation symbol: Figures in brackets refer to item num- bers in drawings or to the drawings themselves.
6 Instruction manual V 2.2 – 08/2007 General This instruction manual includes important instructions and information related to the operating safety and maintenance of the instrument.
7 Leica SP9000 – Automatic knife sharpener Potential hazard Caution: risk of injury when touch- ing the knives and blades as these are extremely sharp. Warning: Avoid touching live parts under any circumstances! 2 . 2 Safety instructions for hand- ling the instrument 2.
8 Instruction manual V 2.1 – 04/2003 3. Instruments properties 3.1 Technical Data Power supply : Overall Dimensions : Model 930 is 115 V / 60 Hz Width : 370 mm Model 940 is 230 V / 50 Hz Height : 460 mm Depth : 540 mm 3.2 General Description Your technical skill is the key to the successful performance of any labora- tory equipment.
9 Leica SP 9000 – Automatic knife sharpener 3. Instrument properties 3.3 Overview - SP9000 Plastic cover Glass Plate Glass plate thumbscreen Plate positional dial Knife holder Hone glass plate holde.
10 Instruction manual V 2.2 – 08/2007 4. Installation 4.1 Check list The Leica Microtome Knife Sharpener is shipped with all accessories re- quired for coarse and fine knife honing of knife edges and for dressing glass hone plate surfaces when necessary.
11 Leica SP 9000 – Automatic knife sharpener 4.2 Installing the instrument 1. Place the sharpener on a sturdy table or laboratory bench and remove tags and retaining tape used for shipment. 2. Assure that the plastic cover fits securely upon the base and is firmly supported when opened.
12 Instruction manual V 2.2 – 08/2007 Key to sharpening success The starting point of any successful sharpening technique is the careful ex- amination of the condition of the knife edge using a microscope. Periodic re- examination during sharpening is equally important.
13 Leica SP 9000 – Automatic knife sharpener For the first resharpening of a new Leica knife or one that has been factory reconditioned by Leica, the honing process must begin with coarse honing. This is necessary in order to develop the sec- ond facet as is explained in the section on ,,Factory Recondition- ing”.
14 Instruction manual V 2.1 – 04/2003 5.2. Put honing plate on holder Two plates are supplied, each with two usable sides. When the plate is properly positioned, tighten the thumbscrew. (Figure 14) 5.3. Apply coarse abrasive to the plate (Shake the abrasive very thoroughly until all particles are in suspension.
15 Leica SP9000 – Automatic knife sharpener Fig. 15.1 Fig. 15.2 5.4. Attach knife With the two clamps facing ,up” and clamp screws loosened, install knife so that the end with the Leica trademark to your right ( Figure 15.1 ). This places the slotted end of the knife to your left as you face the front of the Leica Knife Sharpener.
16 Instruction manual V 2.2 – 08/2007 5.6 Set coarse honing knob Switch the coarse honing knob on the left-hand side of the control panel fully to the left so the direction of the knob is towards „Coarse”. 5.7 Set Timer at 30 minutes When beginning coarse honing operation, set the automatic timer for 30 mi- nutes.
17 Leica SP 9000 – Automatic knife sharpener 5.10 Clean knife - inspect condition Wipe knife with clean cloth moistened with solvent and inspect the cutting facet under a microscope (1OOX).
18 Instruction manual V 2.1 – 04/2003 6. Fine coarse procedure Coarse honing must be followed by fine honing using the Leica Fine Abra- sive. As illustrated in Figure 10, the coarse honing action produces a single facet.
19 Leica SP 9000 – Automatic knife sharpener The fine honing procedure is identical to coarse honing with three excep- tions: 1. Lower honing plate to fine honing position by turning honing dial on the left-hand side of the control panel fully to the right.
20 Instruction manual V 2.2 – 08/2007 6. Fine coarse procedure After Fine Honing is Complete Shut off instrument by depressing ,OFF” button. Clean knife and wipe dry care- fully (Figure 20.1) . Where atmosphere is corrosive and the knife is to be stored for any length of time, lubricate with a good grade of light, neutral oil.
21 Leica SP 9000 – Automatic knife sharpener Abb. 21.1 Abb. 21.2 7. Redressing hone glass plates In order to eliminate excessive redressing time on the hone plates, it is sug- gested that users accumulate no more than three or four hours sharpening time on any plate surface.
22 Instruction manual V 2.2 – 08/2007 3. If the plastic glass retainers are not in place, install them on the posts on the platform and tighten the two thumb screws in each one (Figure 15). The two glass retainers may be left in place during knife sharpen- ing.
23 Leica SP 9000 – Automatic knife sharpener 7. Insert the two lips of the bridge assembly into the slot behind the front panel. Then, with the spring mounted suction cups on the top plate, press down on the bridge and tighten the thumb screw (Figure 19).
24 Instruction manual V 2.2 – 08/2007 The new, or factory reconditioned, Leica Knife has very precise wedge and cutting facet angles. These angles permit the knife to ,meet“ the glass hone plate in the correct manner for proper coarse and fine honing.
25 Leica SP 9000 – Automatic knife sharpener Should the occasion ever arise, the Leica Knife Sharpener can be re- conditioned at the Leica factory in Nussloch, Germany or at many of the Leica Microsystems Technical Service Centres worldwide. This is a cus- tomer service provided at a nominal charge.
26 Instruction manual V 2.2 – 08/2007 Appearance Problem Cause Correction 8. Trouble shooting Fine facet fades out at ends of knife (opposite side of knife has even bevel). or Fine facet fades out at centre of knife (opposite side of knife has even bevel).
27 Leica SP9000 – Automatic knife sharpener 9. Warranty and service Warranty Leica Biosystems Nussloch GmbH guarantees that the contractual prod- uct delivered has been subjected to a comprehensive .
28 Instruction manual V 2.2 – 08/2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Anne De Greef-Safft President Biosystems Division Leica Biosystems Nussloch GmbH Postfach 1120 D-69222 N.
29 Leica SP 9000 – Automatic knife sharpener Peoples Republic of China.
30 Instruction manual V 2.2 – 08/2007 Notice.
Een belangrijk punt na aankoop van elk apparaat Leica Sp9000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Leica Sp9000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Leica Sp9000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Leica Sp9000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Leica Sp9000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Leica Sp9000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Leica Sp9000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Leica Sp9000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
