Gebruiksaanwijzing /service van het product MODEL STRIKER S160 van de fabrikant Lennox
Ga naar pagina of 22
INST ALLA TION AND OPERA TION MANUAL W ARNINGS • Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will retain heat for a while after shutting off the appliance. Severe burns may result. • Carefully supervise children in the same room as appliance.
2 General Safety Precautions 1. If this solid-fuel room heater is not properly installed, a house fire may result. For your safety , follow the installation direc- tions. Contact local building or fire officials about restrictions and installation inspection requirements in your area.
3 T able of Contents General Safety Precautions ................................................................. 2 T esting Information ........................................................................... 4 Draft Requirements .................
4 T esting Information This manual describes the installation and operation of the Striker™ S160 non-catalytic wood heaters. These heaters meet the U.S. Environmental Protection Agency’ s emissions limits for wood heaters sold on or after July 1, 1990.
5 Negative Pressure Warning This appliance is not designed to be operated in a negative pres- sure. Very airtight homes with large kitchen exhaust fans, or homes with furnace cold air returns located in close proximity to the wood stove or fireplace insert may create negative pres- sure in the same room as the heating appliance.
6 Clearances to Combustibles W AR N IN G: BE ABSO LU T EL Y SUR E THE DI S T ANCE BETW E EN THE HEA TER AND THE SURFACE OF ANY COMBUSTIBLE CONSTRUCTION IS NOT LESS THAN SHOWN. Floor Protection USA - The floor in front and under the heater must be protected with a minimum of 3/8” (10 mm) thick noncombustible material.
7 Diagram B: Side View-Alcove & Parallel Installation Diagram A: T op View-Parallel Installation K B A E C D *L K Floor Protection Floor Protection Floor Protection G G F F 72" Min.
8 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Heat Shield Mounting Holes Air Channel Front Figure 2 Figure 1 Outside Air Kit Installation T o install the “Outside Air Kit,” position the clip so that the nut is directly above the hole punched in the back of the heatshield (See Figure 3 ) .
9 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 11. For residential installations, install the first section of stove pipe with the crimped end going down inside the flue collar on the heater . Continue with your stove pipe, installing each section-c rimped end down.
10 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 5. If required, install the Outside Air Kit (cat. no. 71112) as per the following instructions. T o locate the hole in the hearth for outside air mark and cut a 4” (102 mm) hole in the hearth.
11 Post Installation Checks 1. Check that all chimney pipe joints are securely fastened. 2. Check that the heater is securely fastened to the floor (if applicable). 3. Make sure the intake vent has clear access to outside air (if applicable). 4. Make sure the outside air vent has been sealed properly to keep rodents out (if applicable).
12 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Ceramic Fiber Blanket Baffle Bricks T op View Figure 7 Brick Sizes A = 4-1/4” x 9” B = 2-1/4” x 8-7/8” C = 3-1/2” x 9” D = 2-1/4” x 9” E = 1-1/2” x 8-7/8” F = Full Brick (4-1/2” x 9”) G = 1-1/2” x 9” H = 3-1/2” x 8-7/8” Figure 6 3.
13 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Optional Blower Installation A blower , catalog number 71000, can be installed on the stove to improve hot air distribution throughout the room. T o install the blower: 1. Remove all the contents from the blower box.
14 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Starting and Maintaining a Fire Be sure to clean the Nickel or Gold Plated door with a household type cleaner and a ver y soft cloth to remove any fingerprints and residues prior to the first fire.
15 Operating T echniques and Hints Recent developments in wood-burning technology have made wood-burning a cleaner and more convenient way to heat your home. Overall efficiency in a wood-burning appliance is a combina- tion of combustion efficiency and heat transfer efficiency .
16 Maximizing Y our Stove’ s Overall Efficiency It is important to know that for high, combustion efficient, clean burns, you will need to have sufficient temperatures inside the firebo x for thorough combus tion . The best method for determinin g if you have sufficient temperatures is to watch the brick lining in your firebox.
17 Experiment with different loading configurations to achieve longer burns . T r y loading the wood from side to side and nesting it in the ashes to prevent airflow under and around the wood. Fresh wood should be loaded to the back of the firebox or to the sides.
18 T roubleshooting Problem Solution POOR DRAFT : Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys nor - mally have poor drafts. Remember , the stoves’ draft depend solely on the natural draft of the chimney (See drafting section on Page 4 ).
19 Do’ s and Don’ts DO NOT : Install or operate this stove before reading this manual. DO NOT : Close the draft beyond the point at which the flames are completely extinguished. DO NOT : Open the stove door without fully opening the draft first.
20 Replacement Parts - Model S160 Contact an Authorized Lennox Hearth Products dealer to obtain any of these parts. Never use substitute materials. Use of non-approved parts can result in poor performance and safety hazards. BL O W ER P AR T S Ca t . N o .
21 Accessories Model S160 PE D E ST ALS ( RE Q U IR E D ) Ca t . N o . D es c ri pti o n 71 1 0 8 Pe d es tal 71 1 0 9 As h Dr a we r P e de s t al or L EG S ( Req u ir e d ) 70 0 0 0 Ol y m pi c S cu.
22 WARRANTY Y our wood appliance is covered by a limited warranty (provided with the appliance). Please read the warranty to be familiar with its coverage.
Een belangrijk punt na aankoop van elk apparaat Lennox MODEL STRIKER S160 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lennox MODEL STRIKER S160 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lennox MODEL STRIKER S160 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lennox MODEL STRIKER S160 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lennox MODEL STRIKER S160 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lennox MODEL STRIKER S160 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lennox MODEL STRIKER S160 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lennox MODEL STRIKER S160 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
