Gebruiksaanwijzing /service van het product X130E van de fabrikant Lenovo
Ga naar pagina of 184
User Guide ThinkP ad X130e.
Notes: Before using this information and the pr oduct it supports, be sur e to read the following: • Safety and Warranty Guide • Regulatory Notice • “Important safety information” on page vi • Appendix C “Notices” on page 165 The Safety and W arranty Guide and the Regulatory Notice have been uploaded t o the W eb site.
Contents Read this rst . . . . . . . . . . . . . . v Important safety information . . . . . . . . . . vi Conditions that requir e immediate action . . vii Safety guidelines . . . . . . . . . . . . vii Chapter 1. Product overview . . . . . . 1 Locating comput er controls, connectors, and indicators .
Creating and using recovery media . . . . . . 63 Creating recovery media . . . . . . . . . 64 Using r ecovery media . . . . . . . . . . 64 P erforming backup and recovery operations . . . 65 P erforming a backup oper ation . . . . . . 65 P erforming a recovery oper ation .
Electronic emission notices. . . . . . . . . . 157 F ederal Communications Commission Declaration of Conformity . . . . . . . . 157 Industry Canada Class B emission compliance statement . . . . . . . . . . . . . . . 158 European Union - Compliance to the Electromagnetic Compatibility Dir ective .
iv User Guide.
Read this rst Be sur e to follow the important tips given her e to continue to get the most use and enjoyment out of your computer . F ailur e to do so might lead to discomfort or injury, or cause your computer to fail. Protect yourself from the heat that your computer generates.
Protect your computer and data when moving it. Before moving a comput er equipped with a hard disk drive, do one of the following, and make sure that the power switch is off or is blinking: • T urn it off. • P ut it in sleep (standby) mode. • P ut it in hibernation mode.
Conditions that require immediate action Products can become damaged due to misuse or neglect. Some pr oduct damage is serious enough that the pr oduct should not be used again until it has been inspected and, if necessary, repaired by an authoriz ed servicer .
customers to install options or replace CRUs. Y ou must closely follow all instructions when installing or replacing parts. The Off stat e of a power indicat or does not necessarily mean that voltage levels inside a product are zer o.
Extension cords and r elated devices Ensure that extension cor ds, surge pr otectors, uninterruptible power supplies, and power strips that you use are r ated to handle the electrical requir ements of the pr oduct. Never overload these devices. If power strips are used, the load should not e xceed the power strip input rating.
External devices CA UTION: Do not connect or disconnect any external device cables other than USB cable while the computer power is on; otherwise, you might damage your computer . T o avoid possible damage to attached devices, wait at least ve seconds after the computer is shut down to disconnect e xternal devices.
Rechargeable battery notice DANGER Do not attempt to disassemble or modify the battery pack. Att empting to do so can cause an explosion, or liquid leakage from the battery pack. A battery pack other than the one specied by Lenovo, or a disassembled or modied battery pack is not covered by the warranty .
Heat and product ventilation DANGER Computers, ac power adapters, and many accessories can generate heat when turned on and when batteries are char ging.
Electrical current safety information DANGER Electric current from power , telephone, and communication cables is hazardous. T o avoid a shock hazard: • Do not use your computer during a lightning storm.
the equalizer to maximum increases the earphone and headphone output voltage and the sound pressure level. Ther efore, to protect your hearing, adjust the equalizer to an appropriat e level.
Chapter 1. Product overview This chapt er pr ovides information about the locations of connect ors, locating important pr oduct information, computer features, specications, oper ating environment, and pr einstalled software progr ams.
F ront view Figure 1. ThinkP ad X130e front view 1 Ultr aConnect ™ wireless antennas (left) 2 Int egrated camera 3 Ultr aConnect wir eless antennas (right) 4 P ower switch 5 P ower status indicat or.
The power switch also can be progr ammed via P ower Manager to shut down the computer or put it int o sleep (standby) or hibernation mode. 5 P ower status indicator Y our computer has a power status indicator . F or the details, see “P ower status indicator” on page 10.
Right-side view Figure 2. ThinkP ad X130e right-side view 1 Media car d reader slot 2 Always On USB connector 3 USB connector 4 P ower jack 5 Security keyhole 1 Media card reader slot Depending on the model, your comput er might have a Media Car d Reader slot.
By default, even if your comput er is in sleep (standby) mode, the Always On USB connector still enables you to charge some devices, such as iP od ® , iPhone ® , and BlackBerry ® smartphones, by attaching the devices t o the connect or .
Left-side view Figure 3. ThinkP ad X130e left-side view 1 Monit or connector 2 F an louvers (right) 3 HDMI connector 4 USB connector 5 E thernet connector 6 Combo audio jack 1 Monitor connector The monit or connector is used t o connect an ext ernal monitor or project or to your computer .
An indicator to the left of the connector shows the status of ac power . When the ac power adapter is connected, the indicator is on. If a battery is installed in the computer , the indicator is green when the battery char ges. DANGER T o avoid the risk of electrical shock, do not connect the telephone cable to the Ethernet connector .
2 SIM car d slot If your computer has a wireless WAN feature, it might r equire a SIM (Subscriber Identication Module) card to establish a wir eless WAN (Wide Area Network) connection. Depending on the country of delivery, the SIM card might be already installed in the SIM car d slot.
System status indicat ors The illuminat ed dot in the ThinkP ad logo on the outer lid of your computer and on the palm rest works as a system status indicat or: it shows whether the comput er is in sleep (standby), hibernation, or normal mode. The meaning of the indicator is as follows: • Red: The computer is on (in normal mode).
P ower status indicator Y our computer has an indicat or that shows the status of ac power . The meaning of the indicator is as follows: • Green: The ac power adapt er is connected. If a battery is installed on the computer , the indicator is gr een when it is charged.
Machine type and model label The machine type and model label identies your comput er . When you contact L enovo for help, the machine type and model information helps support technicians to identify your comput er and provide faster service.
If no integr ated wireless PCI Expr ess Mini C ard is preinstalled in your comput er , you can install one. T o do this, follow the pr ocedure in “Installing and replacing the PCI Express Mini Car d.
Memory • Double data r ate 3 synchronous dynamic r andom access memory (DDR3 SDRAM) Stor age device • 2.5-inch (7 mm height) hard disk drive • 2.5-inch (7 mm height) solid stat e drive Display The color display uses TFT t echnology . • Size: 11.
• Width: 293.4 mm (11.6 inches) • Depth: 216 mm (8.5 inches) • Height: 32.8 mm (1.3 inches) Heat output • 65 W (222 Btu/hr) maximum P ower sour ce (ac power adapt er) • Sine-wave input at 50.
ThinkV antage T echnologies and software Lenovo pr einstalls on your PC useful and helpful software applications to help you get started, t o stay productive while on the move and to keep you and your computer working. L enovo offers enhanced security, wireless computing, data-migr ation and other solutions for your computer .
T able 1. Applications on Lenovo ThinkV antage T ools (continued) Application Icon name Lenovo ThinkV antage T oolbox or Lenovo Solution Cent er System Health and Diagnostics Mobile Br oadband Activat.
T able 2. Applications in Control P anel (continued) Application Control Panel section Green te xt in Control P anel System Update System and Security Lenovo - Updat e and Drivers ThinkV antage GPS Ne.
• System Update T o access the Lenovo ThinkV antage T ools progr am, click Start ➙ All P rograms ➙ Lenovo ThinkV antage T ools . Note: Lenovo ThinkV antage T ools is available only on models preinstalled with the Windows 7 oper ating system. If your Windows 7 model is not pr einstalled with the progr am, you can download it fr om http://www.
Pr esentation Direct or Pr esentation Dir ector is a display conguration utility that enables you to give pr esentations conveniently . It also enables you to creat e and manage the display schemes. However , by default, Pr esentation Direct or has some pr edened presentation schemes.
20 User Guide.
Chapter 2. Using your computer This chapter provides information on using some of the computer components. This chapter contains the following topics: • “Registering your computer ” on page 21 .
Concerned about security or need to securely dispose of data stored on your hard disk drive or solid state drive? • Study the Security section to nd out how you can prot ect your comput er from theft and unauthoriz ed use. • The P assword Manager preinstalled on your comput er performs many of the security tasks that help prot ect it.
V olume and mute buttons • Fn+Esc: Speaker mute • Fn+F1: Speak er volume down • Fn+F2: Speaker volume up If you mut e the sound and then turn off your computer , the sound will r emain muted when you turn on your comput er again. T o turn on the sound, press the Speaker volume up or Speaker volume down key .
Launching the camer a and audio settings • Fn+F6 If you press Fn+F6, the camer a and audio settings window is opened and the camer a preview is turned on. F r om this window, you can change the camera and audio settings. Note: The C amera settings area only appears if your computer has an integr ated camera.
The computer display becomes dimmer . The purpose of this method is to change the brightness level tempor arily . T o change the default brightness level, change the settings of the P ower Option in the Control P anel or use the P ower Manager . • Fn+F9 Display brightness up using Fn+F9.
Using the Ultr aNav pointing device Y our comput er might come with the UltraNav pointing device. The Ultr aNav consists of the T r ackP oint and the touch pad, each of which is itself a pointing device with both basic and ext ended functions.
Using the T r ackP oint pointing device The T r ackP oint pointing device consists of a pointing stick 1 on the keyboard and thr ee click buttons at the bottom of the keyboar d.
Replacing the cap The cap 1 on the end of the T r ackP oint pointing stick is r emovable. Y ou can replace it as shown in the dr awing. Note: If you r eplace the keyboard, a new keyboard is shipped with the default cap. If you wish, you can keep the cap from your old keyboar d and use it on the new one.
F or Windows 7: 1. Click Start , and then click Control Panel . 2. Click Hardwar e and Sound , and then click Mouse . 3. Click the UltraNav tab and pr oceed to customizing the t ouch pad. F or Windows XP: 1. Click Start , and then click Control Panel .
3. Click the Ultr aNav tab. 4. Select the check box for Show Ultr aNav icon on the system tray . 5. Click OK or Apply . F or Windows XP: 1. Click Start , and then click Control Panel . 2. Click P rinters and Other Hardware , and then click Mouse . 3. Click the Ultr aNav tab.
3. Plug the power cord into an electrical outlet. Tips on using the ac power adapter Y ou can check the status of your batt ery at any time by looking at the battery meter at the bott om of your display . Notes: • When the ac power adapter is not in use, disconnect it fr om the electrical outlet.
1. Right-click the P ower Manager Batt ery Gauge in the task bar . 2. Select P ower off display . • Sleep (standby in Windows XP). In sleep (standby) mode, your work is saved t o memory, and then the hard disk drive or the solid state drive and the computer display are turned off.
Note: If your computer ent ers sleep (standby) or hibernation mode when the batt ery is low, but the alarm message has not yet appeared, the message will appear when the comput er resumes. T o r esume normal operation, press OK . Handling the batt er y DANGER Do not attempt to disassemble or modify the battery pack.
DANGER Do not put the batt er y pack in trash that is disposed of in landlls. When disposing of the battery, comply with local ordinances or regulations and your company's safety standar ds. DANGER There is a danger of an e xplosion if the backup battery is incorrectly placed.
Wireless LAN A wireless local ar ea network covers a relatively small geographic ar ea, such as an ofce building or a house. Devices based on the 802.11 standar ds can connect to this network. Wireless W AN A wireless wide ar ea network covers a broader geographic area.
Note: Befor e you start setting up wireless networking connections by using Access Connections, obtain a Network Name (SSID) and your encryption information fr om your network administrat or . Access Connections, a connectivity assistant progr am, can easily enable one network adapt er and disable the other adapters on demand.
F or Windows XP If your computer is equipped with the int egrated Bluetooth features, you can enable or disable the featur es by pr essing Fn+F5. If you press Fn+F5, a list of wir eless features is displayed. Y ou can enable or disable the Bluetooth features with a single click.
My Bluetooth Places T o use the Bluetooth featur es, do the following: 1. Double-click the My Bluetooth Places icon on the deskt op. 2. F or Windows XP , go to Bluet ooth T asks and double-click View devices in range . A list of the devices on which Bluet ooth has been enabled appears.
F or details, r efer to the help for Bluetooth. T o see the help, double-click My Bluetooth Places , and click Help and then Bluetooth help . Another way to start the help is to right-click Bluetooth Congur ation in the system tr ay of the task bar , and click Advanced Congur ation and then Help .
2. Click P erformance and Maintenance ; then click System . 3. Click the Hardware tab; then click Device Manager . 4. Double-click Bluetooth Radios t o extr act the Bluetooth Radios device tree. 5. Double-click the ThinkPad Bluetooth with Enhanced Data Rate icon to open the P roperties window .
– P ower to the wireless r adio is on. The signal strength of the wir eless connection is ex cellent. • Access Connections Gauge stat es: wireless WAN – No signal – Signal level 1 – Signal level 2 – Signal level 3 Note: F or more information about Access Connections gauge, see the Help in Access Connections.
Enabling or disabling the wireless features Pr ess Fn+F5 to bring up the wireless feature list, such as wireless LAN and Bluet ooth. Select a featur e to enable or disable it. Y ou also can enable or disable the features by the following procedur es. T o enable the wir eless featur e, do as follows: 1.
connector), provided that the external monitor also supports that resolution. F or mor e details, refer to the manuals pr ovided with your monitor . Y ou can set any resolution for either the computer display or the e xternal monitor . When you use both at the same time, the resolution of both is the same.
Note: If your computer cannot detect the e xternal monitor , click the Detect button. 4. Set Resolution . 5. Click Advanced Settings . 6. Click the Monitor tab. Check the monit or information window to make sur e that the monitor type is correct. If it is, click OK t o close the window; otherwise do as follows.
Considerations for attaching an e xternal monitor • When installing an oper ating system, you must install the display driver for your monitor that is supplied with the computer , and the Monitor INF le that is supplied with the e xternal monitor .
• Built-in analog microphone Y our computer also has an audio chip that enables you to enjoy various multimedia audio featur es: • Compliant with Int el ® High Denition Audio. • Recording and playback of PCM and W A V les in 16-bit or 24-bit format.
the Communications settings window, you can preview your video image and take a snapshot of your current image. Y ou also can use the integr ated camer a with other progr ams that pr ovide features such as phot ographing, video capturing, and video confer encing.
• When an application using the Dir ectDraw or the Direct3D is played in full-screen mode, it is shown only on the primary display . • Y ou cannot use the display switching function when you ar e in the Extend deskt op mode. Enabling the Extend desktop function T o enable the Ext end desktop function, do as follows: F or Windows 7: 1.
Using the media card r eader If your comput er has a media car d reader slot, it supports the following cards: • SD car d • SDHC car d • SDXC card • MultiMediaCar d (MMC) Notes: • Y our computer does not support the Content P rotection for Recordable Media (CPRM) featur e for SD cards.
50 User Guide.
Chapter 3. Y ou and your computer This chapt er provides you information about accessibility and traveling with your computer . This chapter contains the following topics: • “ Accessibility and co.
screen clean and set the brightness to levels that enable you t o see the scr een clearly . P ress F7 or F8 to adjust display brightness. Head P osition : Keep your head and neck in a comfortable and neutr al (vertical, or upright) position. Chair : Use a chair that gives you good back support and seat height adjustment.
Accessibility information Lenovo is committ ed to providing people with disabilities gr eater access to information and technology . As a result, the following information provides ways t o help users that have hearing, vision, and mobility limitations get the most out of their computer e xperience.
• T ravel accessories T ravel tips Use the following tr avel tips to travel more condently and efciently with your computer . 1. While it is safe to allow your computer to go thr ough the x r ay machines at airport security stations, it is important to keep your eyes on the comput er at all times to prevent theft.
Chapter 4. Security This chapt er pr ovides information about how to prot ect your comput er fr om theft and unauthoriz ed use. • “ A ttaching a mechanical lock” on page 55 • “Using passwor .
P asswords and sleep (standby) mode If you have set passwords and you put your computer into sleep (standby) mode , the procedur e for resuming operation is as follows: • Y ou ar e not prompted t o type the password when resuming oper ation.
Note: Y ou might want t o note your power -on password in a safe place. Otherwise, if you for get it, you have to tak e your computer to a Lenovo r eseller or a marketing r epresentative to have the password canceled. 11. P ress F10 to exit from the Setup Notice window.
8. A Setup Conrmation window opens. Y ou ar e pr ompted to select User or User + Master . Select User if you want to set only one hard disk passwor d. If you ar e an administr ator or supervisor , you can select User + Master to set two passwords. (The user can change the user password later .
Setup Notice window is displayed. Pr ess F10 t o exit from the Setup Notice window . The user har d disk passwords will be removed. T o change or r emove the User + Master har d disk passwor d, select User HDP or Master HDP .
– Enabling or disabling the Internal Wir eless device – Enabling or disabling the Int ernal Bluet ooth device – Enabling or disabling the Internal Wireless WAN device – Enabling or disabling t.
3. F ollow step 11 and step 12 in “Setting a supervisor passwor d” on page 60 to r emove your supervisor password. Hard disk security T o pr otect passwor ds from unauthorized security attacks, several of the latest technologies and algorithms are int egrated into UEFI BIOS and hardwar e design of ThinkP ad notebooks.
destroy the data physically by smashing the hard disk drive with a hammer , or magnetically by means of strong magnetic power , thus making the data unr eadable. But we recommend that you make use of the software (payware) or service (pay service) specically developed for the purpose.
Chapter 5. Recover y overview This chapter provides information about the r ecovery solutions pr ovided by Lenovo. Note: Y ou can attach a USB CD or DVD drive to the USB connector .
Creating recovery media This section pr ovides instructions on how to creat e recovery media on the Windows 7 oper ating system. Note: On the Windows 7 oper ating system, you can creat e recovery media using discs or e xternal USB stor age devices.
3. Select the optical drive with the boot disc as the startup device and pr ess Enter . After a short delay, the Rescue and Recovery workspace opens. 4. On the Rescue and Recovery menu, click Restore your system . 5. F ollow the instructions on the screen.
4. F ollow the instructions on the screen t o complete the r ecovery operation. • T o perform a r ecovery operation using the Rescue and Recovery pr ogram on the Windows XP oper ating system, do the following: 1. F r om the Windows deskt op, click Start ➙ All Pr ograms ➙ ThinkV antage ➙ Rescue and Recovery .
• T o restor e your har d disk drive from a Rescue and Recovery backup or t o r estore your hard disk drive to the fact ory default settings, click Restore your system and follow the instructions on the screen. F or mor e information about the featur es of the Rescue and Recovery workspace, click Help .
3. In the Startup Device Menu window , select the desir ed optical drive as the rst boot device. Then, insert the rescue disc into the optical drive and press Enter . The rescue medium starts. • If you have cr eated a rescue medium using a USB har d disk drive, use the following instructions t o use the rescue medium: 1.
-OR- • If the subfolder for the device contains a le of setup information (a le with the ext ension .inf ), you can use the Add New Har dware progr am (in the Windows Contr ol P anel) to r einstall the device driver . Not all device drivers can be reinstalled by use of this progr am.
70 User Guide.
Chapter 6. Replacing devices This chapter provides information on the following topics: • “Static electricity pr evention” on page 71 • “Replacing the battery” on page 71 • “Replacing .
Prer equisites for the procedur e DANGER If the rechargeable battery pack is incorrectly replaced, there is danger of an explosion. The battery pack contains a small amount of harmful substances. T o avoid possible injury: • Replace only with a battery of the type recommended by L enovo.
4. Insert a fully char ged battery until it clicks into place 1 , and then slide the battery latch to the locked position 2 . 5. T urn the computer over again.
3. Remove the batt ery. F or information about how to r emove the battery, r efer to “Replacing the batt ery” on page 71. 4. L oosen the scr ews 1 that secure the solid stat e drive or hard disk drive door 2 , and then remove the solid state drive or hard disk drive door .
6. Remove the solid state drive or har d disk drive by lifting its left side. 7. Insert the new solid state drive or har d disk drive as shown in the following pictur e.
8. Slide the solid state drive or har d disk drive rmly into the connector 1 , and then r einstall the screws 2 . 9. P ut the cover back in place 1 and close the cover 2 . Then tighten the scr ews 3 . 10. Reinstall the batt ery . F or information about how to reinstall the battery, refer to “Replacing the battery” on page 71 .
Replacing memory in the slot under the k eyboard 1. T urn off the computer; then disconnect the ac power adapter and all cables fr om the computer . 2. Close the computer display, and turn it over . 3. Remove the batt ery. F or information about how to r emove the battery, r efer to “Replacing the batt ery” on page 71 .
7. With the notched end of the memory module towar d the contact edge side of the socket, insert the memory module 1 into the socket at an angle of about 20 degrees; then pr ess it in rmly 2 . 8. Pivot the memory module downwar d until it snaps int o place.
Replacing the keyboard Y ou can use the following pr ocedures t o replace the keyboard with a new one, available as an option. Prer equisites for the procedur e DANGER During electrical storms, do not connect the cable t o or disconnect it from the telephone outlet on the wall.
5. Remove the scr ews. 6. P ush har d in the direction shown by the arrows 1 in the drawing to unlatch the fr ont side of the keyboard. The keyboard will open up slightly 2 .
7. Remove the cables 2 and 4 by ipping the connect ors 1 and 3 upwards. Now the k eyboard has been r emoved. Installing the keyboard 1. A ttach the cables 1 and 3 by ipping the connectors 2 and 4 downwar ds.
2. Insert the keyboar d. Make sure that the r ear edge of the keyboard is under the fr ame, as shown by the arr ows. 3. Slide the keyboard as shown by the arrows.
4. Reinstall the scr ews. 5. P ut the cover back in place 1 and close the cover 2 . Then tighten the scr ews 3 . 6. Reinstall the batt ery . F or information about how to reinstall the battery, refer to “Replacing the battery” on page 71. 7. T urn the computer over again.
Prer equisites for the procedur e DANGER During electrical storms, do not connect the cable t o or disconnect it from the telephone outlet on the wall. DANGER Electric current from power , telephone, and communication cables is hazardous. T o avoid shock hazard, disconnect the cables befor e opening the cover of this slot.
5. If a t ool for r emoving connectors is included in the package with the new car d, use it to disconnect the cables fr om the card. If no such t ool is included, disconnect the cables by picking up the connect ors with your ngers and gently unplugging them.
7. Align the contact edge of the new PCI Expr ess Mini Car d with the corr esponding socket. Pivot the car d until you can snap it int o place 1 . Secure the card with the scr ew 2 .
10. Reinstall the batt ery . F or information about how to reinstall the battery, refer to “Replacing the battery” on page 71. 11. T urn the computer over again.
5. If a t ool for r emoving connectors is included in the package with the new car d, use it to disconnect the cables fr om the card. If no such t ool is included, disconnect the cables by picking up the connect ors with your ngers and gently unplugging them.
6. Remove the scr ew 1 . The car d pops up 2 . Remove the car d. 7. Align the contact edge of the new PCI Express Mini Car d with the corresponding socket 1 . Pivot the card until you can snap it int o place. Secure the card with the screw 2 . Chapter 6 .
8. Connect the cables to the new PCI Express Mini Car d. Note: Be sure t o attach the red cable t o the connector marked “MAIN” or “M” on the car d, and the blue cable to the connect or mark ed “ AUX” or “ A. ” 9. P ut the cover back in place 1 , close the cover 2 , and then tighten the screws 3 .
If you nd the dummy card in the shipping contents, the SIM card is already installed in the SIM car d slot, and no further installation is needed. Note: The SIM card is identied by the IC chip mounted on one side of the card. Replacement instructions T o replace the SIM card, do as follows: 1.
6. Insert the new SIM card 1 rmly into the slot 2 . 7. Close the SIM card door until it snaps into position. 8. Reinstall the batt ery . F or information about how to reinstall the battery, refer to “Replacing the battery” on page 71 . 9. T urn the computer over again.
Prer equisites for the procedur e DANGER If the backup battery is incorrectly replaced, there is danger of an explosion. The backup battery contains a small amount of harmful substances. T o avoid possible injury: • Replace only with a battery of the type recommended by L enovo.
5. Detach the connect or 1 . Then remove the backup batt ery 2 . Installing the backup batter y 1. Install the backup batt er y 1 . Then attach the connector 2 .
3. Reinstall the batt ery . F or information about how to reinstall the battery, refer to “Replacing the battery” on page 71. 4. T urn the computer over again.
96 User Guide.
Chapter 7. Enhancing your computer This section pr ovides information on installing devices and taking advantage of your comput er's high-technology features.
98 User Guide.
Chapter 8. Advanced conguration While it is important to protect les, data, and settings that ar e on the har d disk drive or on the solid state drive, you might also need to install a new oper ating syst em, install new device drivers, update your syst em UEFI, or recover pr einstalled software.
F or the country or region code requir ed in the installation, use one of the following: Country or region: Code China: SC Denmark: DK Finland: FI F rance: FR Germany: GR Italy: IT Japan: JP Netherlan.
Note: If you remove the hard disk drive fr om the comput er with a single-cor e processor and install it on a computer with a dual-core processor , you can get access t o the har d disk drive.
Installing the Windows Vista Update Module Package The Windows Vista Update Modules are in the following direct ory: C:SWT OOL SOSF IXES . The name of each subfolder is the number of a x module. F or information about each x module, visit the Microsoft Knowledge Base homepage at: http://support.
16. T o continue the installation, pr ess Enter again. Leave the diskett e in the drive until the ne xt reboot; the software might need to be copied fr om the diskette again when the les are copied during setup. 17. Complet e the installation of Windows XP Service P ack 2 by following OS installing instructions.
23. When the Syst em Settings Change window appears, click Y es . The comput er restarts. 24. Install the Intel Chipset Support for Windows 2000/XP/Vista/7. T o do this, r efer to “Installing Int el Chipset Support for Windows 2000/XP/Vista/7” on page 105.
8. Click Update Driver . 9. Select Browse my computer for driver software , and then click L et me pick from a list of device drivers on my computer . 10. Click Have Disk . 11. Specify path C:SWT OOL SDRIVERSMONITOR to this monitor INF . Then, click Open .
T o install Int el Chipset Support for Windows 2000/XP/Vista/7, do the following: 1. Rest ore C:SWT OOL S from the backup copy you made before starting the installation.
6. P ress Esc t o e xit fr om the submenu. 7. If you are on a nested submenu, pr ess Esc repeatedly until you r each the ThinkPad Setup menu. Note: If you need to restor e the settings t o their original state as of the time of pur chase, press F9 t o load the default settings.
• In each submenu, you can enable a function by selecting Enabled , or disable it by selecting Disabled . The following submenu is displayed: • Passwor d : Set passwor d r elated functions. • UEFI BIOS Update Option : Specify the settings for Flash UEFI BIOS update.
T o change the startup sequence, do the following: 1. Select Boot ; then press Ent er . Y ou can use the Boot submenu t o specify the startup sequence that runs when you turn on the power . Refer to “Boot submenu” on page 109. 2. Select the device you want to start rst.
• Boot Order L ock : Enable or disable the Boot P riority Order lock. Restart menu If you need t o close the ThinkP ad Setup and restart the system, select Restart fr om the ThinkP ad Setup menu. The following submenu is displayed: • Exit Saving Changes : Restart the system aft er saving the changes.
Cong menu items T able 3. Cong menu items Menu item Submenu item Selection Comments Wake On LAN • Disabled • AC only • AC and Batt ery Enable the system to Power on when the E thernet controller r eceives a magic packet. If you select “ A C Only”, Wake On LAN is enabled only when ac power adapt er is attached.
T able 3. Cong menu items (continued) Menu item Submenu item Selection Comments settings to enable the Always On USB connector function. F or details about how to enable the Always On USB connector function, refer to the online help of the P ower Manager progr am.
T able 3. Cong menu items (continued) Menu item Submenu item Selection Comments CPU P ower Management • Disabled • Enabled Enable or disable the power saving feature that st op the micr oprocessor clock automatically when there are no system activities.
T able 3. Cong menu items (continued) Menu item Submenu item Selection Comments Note: This sub-menu is not supported in AMD models. Security menu items T able 4. Security menu items Menu item Submenu item Selection Comments Passwor d Refer to “Security menu” on page 107 and “Using passwords” on page 55.
T able 4. Security menu items (continued) Menu item Submenu item Selection Comments Memory P rotection Execution P revention • Disabled • Enabled Some computer viruses and worms cause memory buffers to overow by running code where only data is allowed.
T able 4. Security menu items (continued) Menu item Submenu item Selection Comments Integr ated Camera • Disabled • Enabled If you select “Enabled, ” you can use the integr ated camera. Microphone • Disabled • Enabled If you select “Enabled, ” you can use the Microphone (Iinternal, ext ernal, or Line-In).
T able 5. Startup menu items (continued) Menu item Selection Comments bootable devices which do not have UEFI enabled OS. UEFI/Legacy Boot P riority • UEFI First • Legacy First Select priority of boot option between UEFI and L egacy. Boot Mode • Quick • Diagnostics Screen during the POS T: • Quick : ThinkP ad L ogo scr een is displayed.
system-management applications), and have the comput er start up and function in the same way as an ordinary desktop PC. Once the computer is congur ed and oper ational, you can manage it by use of software and manageability features alr eady integrat ed into the client system and the network.
Startup sequence When your comput er is turned on r emotely, the devices attached to it start in an or der determined by the settings for automatic power-on. T o dene a sequence: 1. On the ThinkP ad Setup menu, select Startup . The S tar tup submenu appears.
120 User Guide.
Chapter 9. Pr eventing problems An important part of owning a ThinkPad Notebook is maintenance. With proper care, you can avoid common problems. The following sections pr ovide information that can help you t o keep your computer running smoothly .
returns any failing error codes or messages, call the Cust omer Support Center with the codes or messages and the computer in front of you. A technician will assist you further . 14. If r equired, you can nd your country's Customer Support Center at: http://www.
T aking care of your computer Although your computer is designed to function reliably in normal work envir onments, you need to use common sense in handling it. By following these important tips, you will get the most use and enjoyment out of your computer .
• Before you install any of the following devices, touch a metal table or a grounded metal object. This action reduces any static electricity fr om your body .
4. T o r emove any crumbs or dust from beneath the keys, you can use a camer a blower with a brush or cool air fr om a hair dryer . Note: A void spraying cleaner dir ectly onto the display or the keyboard. Cleaning your computer display 1. Gently wipe the display with a dry, soft, lint-free cloth.
126 User Guide.
Chapter 10. T roubleshooting comput er problems This chapter explains what to do if you e xperience a problem with your comput er . This chapter contains the following topics: • “Diagnosing pr obl.
• F or Windows XP and Windows Vista: Click Start ➙ All programs ➙ ThinkV antage ➙ Lenovo ThinkV antage T oolbo x . When the application is launched, select a diagnostic test to run. If ther e is any problem, besides the err or messages, a guidance also will be displayed to guide you to x the problem.
If you are uncomfortable or unsure about r emoving components please call the Cust omer Support Center for assistance. 4. While the computer is off, remove all sources of power and ext ernal hardwar e. Refer to the pr ocedure in Replacing a memory module for instructions on how t o r emove and reseat the memory modules.
Solution : The EEPROM checksum is not corr ect (block # 0 and 1). The syst em boar d should be r eplaced, and the bo x serial number needs to be reinstalled. Have the comput er serviced. • Message : 0189: Invalid RFID congur ation information ar ea Solution : The EEPROM checksum is not correct (block # 4 and 5).
• Message : EMM386 Not Installed - Unable to Set P age F rame Base Address. Solution : Edit C:C ONFIG.S Y S and change a line fr om device = C:WINDOWSEMM386 .EXE RAM to device = C:WINDOWSEMM386 .EXE NOEMS and save this le. • Message : Thermal sensing error Solution : The thermal sensor is not functioning correctly .
Solution : Y our scr een saver or power management might have been enabled. Do either of the following: – T ouch the T r ackP oint or the t ouch pad, or pr ess a key t o exit the screen saver . – Pr ess the power switch to resume fr om sleep (standby) or hibernation.
2. Click Hardware and Sound . 3. Click Device Manager . If you ar e prompt ed for an administr ator passwor d or conrmation, type the password or pr ovide conrmation. 4. If the ex clamation mark ! is displayed ne xt to the adapt er name under Network adapters , you might not be using the correct driver or the driver might have been disabled.
Make sure that the wireless r adio is enabled by double-clicking the Access Connections icon in the task bar . Note: If your computer is a Windows 7 model, click Show hidden icons in the task bar . The Access Connections icon is displayed. F or more information about the icon, see the Help in Access Connections.
• Problem : Y ou search for a Bluet ooth-enabled device by clicking View devices in r ange in My Bluet ooth Places, but you cannot nd anything. Solution : Make sur e that the device to which you want to connect is enabled for the Bluetooth connection.
• Problem : Y our computer cannot connect a Bluetooth-enabled computer that uses serial port applications. Solution : Reestablish a connection with the Bluetooth-enabled computer , and try the serial connection again. • Problem : Bluetooth serial port was disconnect ed automatically .
5. If you are using Headset pr ole, select Bluetooth Audio for both Sound playback and Sound recor ding. If you are using A V prole, select Bluetooth High Quality Audio for both Sound playback and Sound recor ding. 6. Click OK to close the Sounds and Audio Devices P roperties window.
• Problem : All or some keys on the e xternal numeric keypad do not work. Solution : Make sur e that the e xternal numeric keypad is correctly connected to the computer .
1. Right-click on the desktop, and click Properties to open the Display Pr operties window . 2. Click the Settings tab. 3. Check whether the screen resolution and color quality are correctly set. 4. Click Advanced . 5. Click the Adapter tab. 6. Make sure that the corr ect device driver name is shown in the adapter information window .
Note: If your comput er cannot det ect the e xternal monitor , click the Detect button. 2. Click the icon for the desired monitor (the Monitor -2 icon is for the external monitor). 3. Click Advanced Settings . 4. Click the Adapter tab. 5. Make sur e that the correct device driver name is shown in the adapter information window.
16. Click OK . F or Windows XP: 1. Connect the ext ernal monitor to the monitor connector , and then connect the monitor to an electrical outlet. 2. T urn on the ext ernal monit or and the computer . 3. P ress Fn+F7 to change the display output location to the external monitor .
1. Connect the external monitor to the monitor connector , and then connect the monitor to an electrical outlet. 2. T urn on the external monit or and the computer . 3. P ress Fn+F7 to change the display output location t o the ext ernal monitor . Note: After pressing Fn+F7, you will need to wait for a moment before the image appears.
9. Select the screen r esolution and color quality of the secondary display . 10. Set the relative position of the each monitor by dragging its icon. Y ou can set the monitors in any relative position, but the icons must touch each other . 11. Click OK to apply the changes.
– Conexant 20671 SmartAudio HD • Problem : Recordings made by using the Microphone input are not loud enough. Solution : Make sur e that Microphone Boost is turned on and set as follows: F or Windows 7: 1. Click Start ➙ Control Panel . 2. Click Hardware and Sound .
• Problem : The sound cannot be turned off completely even if you set the Master volume contr ol at minimum. Solution : Y ou can still hear some sound even though you have set the Master volume contr ol at minimum. T o turn off the sound complet ely, go to the Master volume contr ol and select Mut e speakers (in Windows XP , Mute).
• Problem : The battery pack cannot be charged. Solution : Y ou cannot charge the battery when it is too hot. If the batt ery feels hot, detach ac power adapter , leave computer turned off and allow it to cool to room t emperatur e. Aft er it cools, rechar ge the battery .
A power button pr oblem • Problem : The system does not r espond, and you cannot turn off the comput er . Solution : T urn off the computer by pressing and holding the power button for 4 seconds or mor e.
Solution : If the system does not r eturn from sleep (standby) mode, it might have ent ered sleep (standby) or hibernation mode automatically because the batt er y is deplet ed. Check the sleep (standby) indicator . – If the sleep (standby) indicator is on, your computer is in sleep (standby) mode.
Software problems • Problem : An application does not run correctly . Solution : Make sur e that the pr oblem is not being caused by the application. Check that your comput er has the minimum requir ed memory to run the application. Refer t o the manuals supplied with the application.
150 User Guide.
Chapter 11. Getting support This chapt er offers information about when to communicate with Lenovo and how best t o do it. • “Before you contact L enovo” on page 151 • “Getting help and serv.
Getting help and service If you need help, service, technical assistance, or just want more information about L enovo products, you will nd a wide variety of sour ces available from L enovo to assist you.
• Lenovo hardwar e r epair - If the problem is det ermined to be caused by Lenovo hardwar e under warranty, trained service personnel ar e available to pr ovide the applicable level of service. • Engineering change management - Occasionally, there might be changes that are r equired after a pr oduct has been sold.
154 User Guide.
Appendix A. Regulatory information Wireless related information Wireless inter operability The Wireless LAN PCI Express Mini C ard is designed to be interoper able with any wir eless LAN product that .
Due to the fact that integr ated wir eless cards operat e within the guidelines found in radio frequency safety standards and r ecommendations, Lenovo believes they ar e safe for use by consumers.
If your comput er is shipped without the Regulatory Notice , you can nd it on the Web site at: http://www.lenovo.com/support T o view the Regulatory Notice on the W eb sit e, do the following: 1. Go to: http://www.lenovo.com/support In the right pane, type your computer number in the Quick P ath led, and click Go .
Industry C anada Class B emission compliance statement This Class B digital apparatus complies with Canadian ICES-003. Cet appar eil numérique de la classe B est conforme à la norme NMB-003 du Canada.
K orea Class B compliance statement Japanese VCCI Class B statement Japan compliance statement for products which connect t o the power mains with r ated current less than or equal to 20 A per phase L.
160 User Guide.
Appendix B. WEEE and recycling statements Lenovo encour ages owners of information technology equipment to responsibly r ecycle their equipment when it is no longer needed. Lenovo offers a variety of progr ams and services t o assist equipment owners in recycling their IT products.
Disposing of a L enovo computer components Some L enovo computer products sold in Japan might have components that contain heavy metals or other environmental sensitive substances.
framework for the return and r ecycling of used batteries and accumulators as applicable throughout the European Union. This label is applied to various batteries to indicate that the batt ery is not to be thr own away, but rather r eclaimed upon end of life per this Dir ective.
164 User Guide.
Appendix C. Notices Lenovo might not offer the products, services, or features discussed in this document in all countries. Consult your local L enovo repr esentative for information on the pr oducts and services currently available in your ar ea.
T rademarks The following terms ar e tr ademarks of L enovo in the United S tates, other countries, or both: Lenovo Access Connections Active P rotection System Rescue and Recovery ThinkP ad ThinkV an.
.
Part Number: (1P) P/N: **.
Een belangrijk punt na aankoop van elk apparaat Lenovo X130E (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lenovo X130E heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lenovo X130E vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lenovo X130E leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lenovo X130E krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lenovo X130E bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lenovo X130E kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lenovo X130E . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
