Gebruiksaanwijzing /service van het product 9EZ van de fabrikant Lexmark
Ga naar pagina of 20
HIGH WALL AIR CONDITIONER GB User manual and installation guide HW 9EZ 12EZ 18EZ.
2 GB SAFET Y INSTRUC TIONS Thank you for choosing this innovative Amcor air conditioner . W e suggest that you keep this manual in a safe place for future reference. It describes the many benefits and advanced features this unique product has to offer .
3 GB Do not use your air conditioner when: the power cord is damaged. there is a chance of liquids falling on the unit. it a close to a heat source. there is a risk of interference from foreign objects. This air conditioner is not made for DIY repair .
4 GB REMOTE CONTROL LCD display: temperature timer setting timer on/off fan fan speed louvre setting or indication of active mode or selected option Buttons: 1. T emperature setting 2. ON/OFF 3. Swing 4. Air flow 5. Sleep 6. Mode 7. F an speed 8. Timer 9.
5 OPER A TION GB General • T urn the unit on with the ON / OFF BUTTON [2]. The last used operating mode is selected. • The ON / OFF BUTTON turns the appliance off; the operating mode active at this moment is stored in memory and will be used when the air conditioner is switched back on again.
6 GB F an mode 1. Press the MODE BUTTON [6] until the symbol appears next to FAN . 2. Use the FAN SPEED BUTTON [7] to set the fan speed. 3. Use the SWING BUTTON [3] and the AIR FLOW BUTTON [4] to adjust the air flow direction. Sleep button Press the SLEEP BUTTON [5], the symbol appears on the right hand side of the display next to SLEEP .
7 Auto restart The air conditioner will automatic restart when electricity is restored after a power cut. If in doubt, check the settings. Range of internal thermostat The internal thermostat can be set at a desired temperature between 16 and 32 °C. Note that whether the desired value is achieved depends on conditions in the room.
8 FIL TE RS Opening: at the A recesses, pull the front part up. The front part will stay horizontal (turn up 90 °). Closing: press the front part down at the sides at B and in the middle at C. Make sure it is properly closed (click). 1. Hold the front part open (or put it in horizontal position) and remove the filter(s).
9 CLE ANING T urn the air conditioner off and remove the plug from the mains outlet. Indoor unit Dust regularly with a dry cloth or slightly damp paper towel. Never use chemicals or solvents. Never spray a liquid in or over the appliance. Outdoor unit Remove dirt and keep the air intake and exhaust openings free of leaves, etc.
10 GB N N N N 8 8 8 8 8 8N 8N 8IJDISPPNJTCFTUTVJUF.
11 GB SAFET Y A SPEC TS Check the network voltage. Make sure that the existing network voltage corresponds to the value specified on the type tag on the appliance. Keep the work area tidy . C arelessness in the work area can lead to accidents. Use the right tools.
12 SAFET Y Read the section on safety aspects and these instructions before you start. Stick to the work sequence and working method shown here. F or technical or commercial reasons, the manufacturer may make changes to the appliance or component parts, without general notification.
13 F or operational convenience and for safety , ensure there is enough space between the unit and walls, windows and ceiling. Pipe lines can be connected in the directions 1, 2, 3, 4 or 5 as indicated in Figure 3. When connection 3, 4 or 5 is chosen, a groove for the pipes has to be opened on the base stand.
14 Inspections: • See if the hooks at the top and bottom are firmly fixed. • See if the position of the master unit is properly levelled. • The drain pipe must not curve upward (Figure). • The drain pipe must be at the lower part of the wall pipes (Figure) to avoid possible restriction to the water flow .
15 GB • use expansion bolts to fix the mounting supports on the wall • use bolts and nuts to fix the outdoor unit firmly on the supports and keep on the same level • if the unit is installed on the wall or at the roof top, the supports have to be firmly fixed to resist earthquake or strong wind.
16 • Use a thermal tube to wrap the joints and wrap the tube tightly with ethylene tape. • Fix the wrapped pipelines vertically on the external wall with duct through and pipe clamps, available at DIY-stores. Fill the gaps in the holes made for the pipeline to prevent rain-water from entering.
17 GB PA R T S Indoor unit Outdoor unit Air filter Room temperature detecting probe Air inlet side and rear Air discharge Drain tube Air flow direction adjusting Air outlet Refrigerant piping connecti.
18 GB TECHNI CA L DA T A Model HW-9EZ HW-12EZ HW-18EZ Cooling capacity measured conform EN 14511 BTU/h 9200 12000 16500 kW 2.7 3.51 4.82 Heating capacity BTU/h 9500 12300 17400 kW 2.8 3.6 5.1 Power supply 220 – 240 V • 50 Hz • 1Ph Power consumption W 840/780 1100/1000 1600/1580 Current A 3.
19 GB Important The wires in the mains lead on this appliance are coloured in accordance with the following code: Green and Y ellow – Earth Blue – Neutral Brown – Live The green and yellow wire must be connected to the terminal in the plug which is marked with the letter E or with the earth symbol .
HW-EZ 913126320 China Shan Xia Industrial Development Zone, Heng Li T own, Dongguan City , Guangdong Province, China Plant One - Amcor (China) Ltd T el: +86 769 8372 1090 F ax: +86 769 8372 1790 Email: amcorcn@amcorgroup.com Plant T wo - Amcor Appliances Ltd T el: +86 769 8372 1970 F ax: +86 769 8372 1790 Email: amcorappl@amcorgroup.
Een belangrijk punt na aankoop van elk apparaat Lexmark 9EZ (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lexmark 9EZ heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lexmark 9EZ vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lexmark 9EZ leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lexmark 9EZ krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lexmark 9EZ bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lexmark 9EZ kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lexmark 9EZ . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
