Gebruiksaanwijzing /service van het product 90VK MU-42PZ90R van de fabrikant LG Electronics
Ga naar pagina of 39
PLASMA MONIT OR OWNER’S MANUAL Please read this owner ’s manual carefully before operating the Monitor . Retain it for future reference. Record model number and serial number of the Monitor . See the label attached on the back of the Monitor and quote this information to your dealer when you require service.
2 Plasma Display Warning W ARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE P ARTS INSIDE. REFER TO QUALIFIED SER VICE PERSONNEL.
Owner ’ s Manual 3 Safety Instructions Important safeguards for you and your new product Y our product has been manufactured and tested with your safety in mind.
4 Plasma Display Safety Instructions Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Grounding Conductor (NEC Section 810-21) Ground Clamps P ower Service Grounding Electrode System (.
Owner ’ s Manual 5 Contents After reading this manual, keep it handy for future reference. W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 Plasma Display Introduction Introduction Introduction What is a Plasma Display Panel (PDP)? If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
Owner ’ s Manual 7 Introduction Controls Controls Connection Options Connection Options R ( ) ( ) ( ) ( ) L VIDEO INPUT RS-232C INPUT (CONTROL/SERVICE) EXTERNAL SPEAKER YP B P R (MONO) R AUDIO L R AUDIO L S-VIDEO AC INPUT AUDIO INPUT AUDIO INPUT AUDIO INPUT REMOTE CONTROL COMPONENT INPUT DVI INPUT RGB INPUT RGB OUTPUT 1 1.
8 Plasma Display Introduction Remote Control Key Functions Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the monitor . - Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function.
Owner ’ s Manual 9 Installation Installation Installation D-sub 15 pin Cable Owner ’ s Manual 1.5V 1.5V Batteries BNC-RCA Adapter Power Cord 123 456 78 0 9 POWER SLEEP INPUT SELECT APC DASP ARC PIP ARC PIP TWIN PICTURE SWAP MENU MUTE OK VOL POWER STOP PLAY FF REC REW P/STILL WIN.
10 Plasma Display Installation W W all Mount: V all Mount: V ertical installation (MU-42PZ44M/44V/90C/90M/90V series models only) ertical installation (MU-42PZ44M/44V/90C/90M/90V series models only) Detailed installation instructions are included in the optional V ertical Wall Mounting Bracket Installation and Setup Guide, see your dealer .
Owner ’ s Manual 11 Installation External Equipment Connections External Equipment Connections NOTE: All cables shown are not included with the plasma display .
12 Plasma Display Installation • Component Input ports T o get better picture quality , connect a DVD player to the compo- nent input ports as shown below .
Owner ’ s Manual 13 Installation How to connect 1. T o get the best picture quality , adjust the PC graphics card to 800x600, 60Hz. 2. Use the monitor ’ s RGB INPUT or DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector .
14 Plasma Display Installation Resolution 640x350 720x400 640x480 848x480 852x480 Horizontal Frequency(KHz) 31.468 37.861 31.469 37.927 31.469 35.000 37.861 37.500 43.269 31.500 35.00 37.500 31.500 35.000 37.500 70.09 85.08 70.08 85.03 59.94 66.66 72.
Owner ’ s Manual 15 Operation T urning on the Monitor just after installation T urning on the Monitor (power cord is still connected) 1. Connect power cord correctly . 2. Press the ON/OFF button on the Monitor . At this moment, the Monitor is switched to standby mode.
16 Plasma Display Operation - Each adjustment for the Picture menu options doesn ’ t effect other input sources. Readjust Picture menu options for each of the following sources.
Owner ’ s Manual 17 Operation 1. Press the DASP button repeatedly to select the appropriate sound setup as shown below . DASP DASP (Digital (Digital Auto Sound Processing) Auto Sound Processing) 1. Press the MENU button and then use D / E button to select the SOUND menu.
18 Plasma Display Operation - T imer functions operate only if current time has been set. - Off-T imer function overrides On-Timer function if they are set to the same time. - The monitor must be in standby mode for the On-T imer to work. On/Of On/Of f f T T imers Setup imers Setup 1.
Owner ’ s Manual 19 Key Lock Key Lock - The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing by disabling the front panel controls. - This Monitor is programmed to remember which option it was last set to even if you turn the monitor off.
20 Plasma Display Special Menu Options continued Special Menu Options continued SPECIAL Prev. Language Key lock ISM Method Low power Set ID Caption / T ext Captions OSD Rotate G G Normal Rotate SPECIAL MENU 1. Press the MENU button and then use D / E button to select the SPECIAL menu.
Owner ’ s Manual 21 Operation Auto Auto Adjustment Adjustment - RGB (PC) mode only; This function doesn ’ t work for RGB-DTV mode. - Automatically adjusts picture position and minimizes image shaking. - After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment.
22 Plasma Display Adjusting Horizontal/ V Adjusting Horizontal/ V ertical Position ertical Position 1. Press the MENU button and then use D / E button to select the SCREEN menu. 2. Press the G button and then use D / E button to select Position . 3. Press the G button and then use D / E / F / G button to adjust the position.
Owner ’ s Manual 23 Operation Split Zoom Split Zoom - Enlarges the picture in correct proportions. - Split Zoom can be used for all input sources. - In 2-Split Zoom mode, you can only move the image up or down. - If an image is enlarged, a section can be viewed without using Split Zoom.
24 Plasma Display - PIP lets you view 2 dif ferent inputs pictures (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - Y ou can also adjust the PIP features in the PIP/DW menu (Except Swap function).
Owner ’ s Manual 25 Operation - As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the same time.
26 Plasma Display No. Pin name 1 No connection 2 RXD (Receive data) 3 TXD (T ransmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 CTS (Clear to send) 9 No Connecti.
Owner ’ s Manual 27 External Control Device Setup Set ID Set ID Use this function to specify a monitor ID number . Refer to ‘ Real Data Mapping 1 ’ . See page 28. • Baud rate : 1 15200 bps (UART) • Data length : 8 bits • Parity : None * Use a crossed (reverse) cable.
28 Plasma Display External Control Device Setup 02. Input Select (Command2:b) (Main Picture Input) G T o select input source for the Monitor . Y ou can also select an input source using the INPUT SELECT button on the Monitor's remote control.
Owner ’ s Manual 29 External Control Device Setup 09. Color (Command2:i) G T o adjust the screen color . Y ou can also adjust color in the Picture menu. T ransmission Data Min : 0 ~ Max : 64 • Refer to ‘ Real data mapping 1 ’ . See page 28. [k][i][ ][Set ID][ ][Data][Cr] Acknowledgement [i][ ][Set ID][ ][OK][Data][x] 10.
30 Plasma Display External Control Device Setup 22. Red Adjustment (Command2:v) G T o adjust red in color temperature. T ransmission Data Min: 0 ~ Max: C8 • Refer to ‘ Real data mapping 3 ’ as shown below . [k][v][ ][Set ID][ ][Data][Cr] Acknowledgement [v][ ][Set ID][ ][OK][Data][x] 23.
Owner ’ s Manual 31 External Control Device Setup 27. ISM Method (Command2:p) G T o avoid having a fixed image remain on screen. T ransmission Data 0: Normal 1: White wash 2: Orbiter 3: Inversion [j][p][ ][Set ID][ ][Data][Cr] Acknowledgement [p][ ][Set ID][ ][OK][Data][x] 28.
32 Plasma Display G Connect your wired remote control to the Remote Control port on the Monitor . G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz G Configuration of frame G R.
Owner ’ s Manual 33 IR Code 00H 01H 02H 03H 08H C4H C5H 09H 10H 11 H 12H 13H 14H 15H 16H 17H 18H 19H 0BH 98H D5H C6H BFH 5AH D8H 0EH 44H 43H 52H 4DH 60H 61H 63H 64H 6BH 40H 41H 69H 6AH 7BH 79H 76H 7.
34 Plasma Display T roubleshooting Checklist No output from one of the speakers • Adjust Balance in the SOUND menu. (Refer to p.17) Unusual sound from inside the monitor • A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or of f and does not indicate a fault with the monitor .
Owner ’ s Manual 35 Maintenance & Specification 1. Here ’ s a great way to keep the dust of f your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it ’ s almost dry , and then use it to wipe the screen.
36 Plasma Display Specification • The specifications shown above may be changed without notice for quality improvement. Product Specifications Product Specifications MODELS Width (inches / mm) Heigh.
Owner ’ s Manual 37 Notes Notes Notes.
38 Plasma Display Notes Notes Notes.
Owner ’ s Manual 39 Notes Notes Notes.
Een belangrijk punt na aankoop van elk apparaat LG Electronics 90VK MU-42PZ90R (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen LG Electronics 90VK MU-42PZ90R heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens LG Electronics 90VK MU-42PZ90R vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding LG Electronics 90VK MU-42PZ90R leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over LG Electronics 90VK MU-42PZ90R krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van LG Electronics 90VK MU-42PZ90R bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de LG Electronics 90VK MU-42PZ90R kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met LG Electronics 90VK MU-42PZ90R . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
