Gebruiksaanwijzing /service van het product 4000 van de fabrikant Life Fitness
Ga naar pagina of 47
Model 4000 Treadmill Customer Support Services SERVICE MANUAL.
© 1998 Life Fitness, a division of Brunswick Corporation. All rights reserved. All rights reserved. Life Fitness, Lifecycle, Lifepulse and Flexdeck are registered trademarks, and Heart Rate Zone Training, Lifespring and RELY ON IT are trademarks of Brunswick Corporation.
Life Fitness Model 4000 Treadmill INTRODUCTION HOW TO USE THIS SERVICE MANUAL In the unlikely event that an operating problem may occur with your Life Fitness model 4000 treadmill, this Service Manual will instruct and guide you on the quickest, most efficient manner in which to approach the situation.
FCC Warning - Possible Radio/Television Interference NOTE: This equipment has been tested and found to comply with the limits pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Life Fitness Model 4000 Treadmill TABLE OF CONTENTS INTRODUCTION (How to use this Service Manual) TABLE OF CONTENTS SECTION I PAGE THEORY OF OPERATION 1 TROUBLESHOOTING GUIDES NO POWER ..................................................................
1 Life Fitness Model 4000 Treadmill THEORY OF OPERATION The operational functions of the Life Fitness Model 4000 Treadmill are accomplished by four main components: the Control Board , the Display Console , the Drive Motor and the Lift Actuator . The Treadmill user and the control board provide input to the display console.
2 Life Fitness Model 4000 Treadmill TROUBLESHOOTING GUIDE Symptom: NO POWER Malfunction Probable Cause Corrective Action No Power On/off switch Turn unit On. Insufficient power source Plug treadmill into power source with proper electrical requirements.
3 Life Fitness Model 4000 Treadmill TROUBLESHOOTING GUIDE Symptom: NOISY TREADMILL Malfunction Probable Cause Corrective Action Rubbing sound from beneath machine Foreign objects may be stuck under the machine Inspect underneath Belt and Machine. Remove any debris or accumulation.
4 Life Fitness Model 4000 Treadmill TROUBLESHOOTING GUIDE Symptom: STRIDING BELT Malfunction Probable Cause Corrective Action Striding Belt will not move Insufficient power source Faulty Control Board Plug treadmill into power source with proper electrical requirements.
5 Life Fitness Model 4000 Treadmill TROUBLESHOOTING GUIDE Symptom: UNIT RESETS RANDOMLY Malfunction Probable Cause Corrective Action Unit Resets Randomly Insufficient Power Source Plug Treadmill into power source with proper electrical requirements. (See Operational Manual) Damaged Line Cord Replace Line Cord.
6 Life Fitness Model 4000 Treadmill TROUBLESHOOTING GUIDE Symptom: DISPLAY DOES NOT ILLUMINATE OR RESPOND TO INPUT Malfunction Probable Cause Corrective Action Display will not illuminate when machine is turned on. Insufficient power source. Plug Treadmill into power source with proper electrical requirements.
7 Life Fitness Model 4000 Treadmill TROUBLESHOOTING GUIDE Symptom: UNIT WILL NOT ELEVATE Malfunction Probable Cause Corrective Action Unit will not elevate Line Cord is crossed over lifting assembly Check position of Line Cord placement. Faulty Lift Actuator (limits) Perform Lift Test (See Diagnostics).
8 Life Fitness Model 4000 Treadmill TROUBLESHOOTING GUIDE Symptom: ERROR DISPLAY MESSAGES Malfunction Probable Cause Corrective Action ERROR MESSAGES: START UP (Occurs when the Striding Belt, upon start up, will speed up at a high rate) Bad connection to Opto Speed Sensor Check all electrical connections.
9 Life Fitness Model 4000 Treadmill TROUBLESHOOTING GUIDE Symptom: OPTIONAL HEARTRATE KIT DOES NOT RESPOND Malfunction Probable Cause Corrective Action Heart Rate system does not respond Heart Rate cable not connected Check all electrical connections.
10 Life Fitness Model 4000 Treadmill NOTES:.
1 Life Fitness Model 4000 Treadmill DIAGNOSTIC TESTS This Section describes the test procedures for the Life Fitness 4000 Treadmill Display Console Board including the Heart Rate feature (operational only if equipped with the optional Heart Rate Kit Tray).
2 Life Fitness Model 4000 Treadmill DIAGNOSTIC TESTS ( Continued ) The SPEED τ key is used for the following testing information: ⇒ CHECK THE DISPLAY/KEYPAD FUNCTIONS ⇒ REVIEW STATISTICS ⇒ IDENTIFY SOFTWARE VERSION Use the ENTER key to advance through the test.
3 Life Fitness Model 4000 Treadmill DIAGNOSTIC TESTS (Continued) The INCLINE τ key is used for the following testing information: ⇒ ELEVATION TEST/ HOME SWITCH ⇒ SPEED MODE OPERATION ⇒ HEARTRATE MODE OPERATION (if equipped with optional heart rate kit) ⇒ BLANKING ON/OFF Power up the unit while holding down the INCLINE τ key.
4 Lifestride Model 4000 Treadmill DIAGNOSTIC MODE ENTRY (Continued) TO TEST THE ELEVATION : Press the INCLINE σ key to elevate the treadmill. Press the INCLINE τ key to lower the unit. A beeping will occur while the unit is being lowered and the home switch is activated.
1 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE THE VENT COVER Tools Required: Phillips Screwdriver Step 1 Turn the power OFF at the ON/OFF switch and then unplug the unit from the electrical outlet. Step 2 Use a phillips screwdriver to remove the two SCREWS securing the sides of the VENT COVER to the MOTOR COVER .
2 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE MOTOR COVER Tools Required: Phillips Screwdriver, hex key wrench set Step 1 Turn the power OFF at the ON/OFF switch and then unplug the unit from the electrical outlet. Step 2 Remove the VENT COVER (See “How To.
3 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE THE DISPLAY CONSOLE Tools Required: Phillips Screwdriver Step 1 Turn the power OFF at the ON/OFF switch and then unplug the unit from the electrical outlet. Step 2 Remove the TRAY, if equipped with the optional HEART RATE kit.
4 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE THE HANDLEBAR AND HANDRAILS Tools Required: Phillips Screwdriver, hex key wrench set Step 1 Turn the power OFF at the ON/OFF switch and then unplug the unit from the electrical outlet. Step 2 Remove the DISPLAY CONSOLE.
5 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE THE DECK AND STRIDING BELT Tools Required: Phillips Screwdriver, socket set, hex key wrench set Step 1 Turn the power OFF at the ON/OFF switch and then unplug the unit from the electrical outlet.
6 Life Fitness Model 4000 Treadmill How To ... ADJUST AND TENSION THE STRIDING BELT Tools Required: Hex key wrench set, phillips screwdriver A. REPLACING THE STRIDING BELT WITH A NEW STRIDING BELT Step 1 After installing the new STRIDING BELT, but prior to tensioning, place two pieces of tape exactly 38.
7 Life Fitness Model 4000 Treadmill How To... ADJUST AND TENSION THE STRIDING BELT ( Continued ) Tools Required: Hex key wrench set, phillips screwdriver It is EXTREMELY important that the treadmill be correctly leveled prior to any tracking adjustments.
8 How To... ADJUST AND TENSION THE STRIDING BELT ( Continued ) Tools Required: Hex key wrench set, phillips screwdriver Step 3 Repeat adjustments until the STRIDING BELT appears centered. Allow the machine to continue running for several minutes to observe if the tracking remains stabilized.
9 Life Fitness Model 4000 Treadmill H ow To... REMOVE AND REPLACE THE FRONT ROLLER ASSEMBLY Tools Required : Phillips screwdriver, socket set, hex key wrench set Step 1 Turn the power OFF at the ON/OFF switch and then unplug the unit from the electrical outlet .
10 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE THE REAR ROLLER Tools Required Socket and ratchet set, hex key wrench set Step 1 Turn the power OFF at the ON/OFF switch and then unplug the unit from the electrical outlet. Step 2 Remove the MOTOR COVER.
11 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE THE HEATSINK CONTROL B OARD ASSEMBLY Tools Required: Phillips Screwdriver, socket and ratchet set, hex key wrench set WARNING: FAILUR.
12 How To ... REMOVE AND REPLACE THE HEATSINK CONTROL B OARD ASSEMBLY ( C ontinued ) Step 6 Use a socket wrench to loosen and remove the two SCREWS securing the GROUNDING WIRES to the HEATSINK CONTROL BOARD ASSEMBLY . Step 7 Lift off the PROTECTIVE COVER from the top of the CAPACITOR.
13 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE THE DISPLAY WIRE HARNESS Tools Required: Phillips Screwdriver, socket and ratchet set, hex key wrench set WARNING: FAILURE TO OBSERVE.
14 How To ... REMOVE AND REPLACE THE LIFT ACTUATOR ASSEMBLY Tools Required: Phillips screwdriver, standard screwdriver, hex key wrench set WARNING: FAILURE TO OBSERVE SAFE PROCEDURES WHEN SERVICING TH.
15 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE THE DRIVE MOTOR BELT Tools Required: Phillips screwdriver, socket and ratchet set, hex key wrench set Step 1 Turn the power OFF at the ON/OFF switch and then unplug the unit from the electrical outlet.
16 How To ... REMOVE AND REPLACE THE DRIVE MOTOR BELT ( Continued ) Step 5 Lift the FRONT ROLLER ASSEMBLY from the EXTRUSION BRACKETS and position the FRONT ROLLER within the STRIDING BELT to allow for removal of the DRIVE MOTOR BELT from the DRIVE MOTOR and FRONT ROLLER PULLEYS.
17 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE DRIVE MOTOR Tools Required: Phillips screwdriver, socket and ratchet set, hex key wrench set Step 1 Turn the power OFF at the ON/OFF switch and then unplug the unit from the electrical outlet.
18 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE DRIVE MOTOR ( Continued ) Step 7 Remove the two DRIVE MOTOR ASSEMBLY mounting SCREWS securing the ASSEMBLY to the MOTOR MOUNTING BRACKET by using a 1/4” hex wrench. Remove the DRIVE MOTOR ASSEMBLY from the unit.
19 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE THE LIFESPRINGS Tools Required: Phillips screwdriver, socket and ratchet set, hex key wrench set Step 1 Turn the power OFF at the on/off switch and then unplug the unit from the electrical outlet.
20 Life Fitness Model 4000 Treadmill How To ... REMOVE AND REPLACE THE TRAY ( O ptional Heart Rate Kit ) Tools Required: Phillips screwdriver Step 1 Turn the power OFF by unplugging the unit at the electrical outlet. Step 2 Remove the two SCREWS located on the underside of the TRAY which are securing the TRAY to the DISPLAY CONSOLE.
21 Life Fitness Model 4000 Treadmill NOTES:.
1 Life Fitness Model 4000 Treadmill WIRING DIAGRAM Life Fitness Model 4000 Treadmill.
2 PARTS IDENTIFICATION SN # 558000 - UP Leg Leveler 0017-00009-0796 Wheel OK40-01021-0000 Motor Shroud AK40-00037-0002 Console Assembly AK40-00057-0001(R) Eng/Met AK40-00057-0004(R) Frn/Met Overlay Be.
3 Life Fitness Model 4000 Treadmill PARTS IDENTIFICATION SN # 558000 - UP End Cap( LT) OK40-01086-0008 End Cap(RT) OK40-01086-0007 Extrusion(RT) OK40-01165-0001 Extrusion(LT) OK40-01165-0002 Handrail .
4 Life Fitness Model 4000 Treadmill PARTS IDENTIFICATION SN # 558000 - UP Transformer 0017-00003-0751(120v) 0017-00003-0758(230v) Lift Pin Kit GK45-00002-0009 Drive Belt OK40-01014-0000 Front Roller A.
5 Life Fitness Model 4000 Treadmill COMMUNICATING BY FAX If you would like to submit a parts order, or if you need help troubleshooting a problem, we have included, for your convenience, a FAX form on the following page. Simply make a copy (or copies) of the FAX sheet and fill in the necessary information.
6 CUSTOMER SUPPORT SERVICES PARTS ORDER ( IF BOTH SALE PLEASE INDICATE ) PRODUCT TROUBLESHOOTING WARRANTY NAME: CUSTOMER NO: DATE: PHONE: FAX: CONTACT NAME: METHOD OF SHIPMENT: 1 DAY 2 DAY GROUND PARTS ORDER FORM ITEM NO. PART NUMBER DESCRIPTION QUANTITY 1 2 3 4 5 6 PRODUCT TROUBLESHOOTING PRODUCT NAME: SERIAL NO.
7 Life Fitness Model 4000 Treadmill NOTES:.
Een belangrijk punt na aankoop van elk apparaat Life Fitness 4000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Life Fitness 4000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Life Fitness 4000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Life Fitness 4000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Life Fitness 4000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Life Fitness 4000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Life Fitness 4000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Life Fitness 4000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
