Gebruiksaanwijzing /service van het product VX2000 van de fabrikant Light & Motion
Ga naar pagina of 17
Owner’ s Manual www .uwimaging.com VX2000 Bluefin.
3 T able of Contents Quick Start Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Bluefin VX2000 Operation - Camera Preparation . . . . . . . . . . . . . . . . . . . . . . . . . .6 Mounting the Camera .
5 Quick Start Guide Every Light & Motion housing is pr essure tested prior to shipping. However , unseen damage may have occurred during shipping. It is str ongly recommended to test dive with only the housing prior to installing the camcorder . 1) Attach a fully charged Sony NP-750 battery to the camcorder .
7 Operation The Bluefin VX2000 is designed to access most camcorder featur es using a combination of infrared commands from the Smart Grips as well as mechanical interfaces on the housing. Rear Plate ON/MODE - T urns camcorder on from off state. When camcorder is in power ed state, loops between Camera - Memory and VTR modes.
8 9 Using the Bluefin VX2000 in Camcorder mode Camcorder POWER switch should be set to MEMORY setting when installed into the housing. When the rear plate is secured to the housing, the camcorder will switch to CAM mode. Left Smart Grip (ref. fig. 9) LIGHTS - After initial power up from battery pod, cycles lights through output cycles.
Using the Bluefin VX2000 in VTR mode Left Grip (ref. fig. 1 1) F AR/- Frame Back while paused and r everse direction during playback NEAR/+ Frame Advance while paused PHOTO DIS. - Rewind during Stop and high speed reverse during Playback LIGHTS - Not used PHOTO - Captures still image to Memory Stick Right Grip (ref.
Housing Storage Store housing and T ravel Case in a dry location. 24 hours after a dive, leave the Rear Plate off the housing to allow for air circulation. Similarly , leave T ravel Case Lid about two inches open. Allow any r esidual water to evaporate from the T ravel Case prior to storing the housing.
Using Manual Focus The Bluefin VX2000 F AR/-, NEAR/+ and MOM.AF buttons will switch the camcorder from auto to manual focus. One technique is to toggle the F AR and NEAR buttons until the subject is in focus. Because this method is slow , we recommend the following technique.
Bluefin VX2000 Lights - Getting Started Pictured below are the components of both the SunRay -X Pr o and the SunRay -X Elite lighting systems. T ake a moment to familiarize yourself with each part for later identification and use.
19 18 Removing Batteries 1) Rotate latch at the front of the pod counter -clockwise 1/8 turn or until it stops. 2) Pull the front cap of f the pod. 3) Pull the battery from the pod using removal strap (r ef. fig. 17 & 18). Mounting Batter y Pods Battery Pods can be mounted prior to installing batteries into pods.
21 20 Assembly with Universal Mounts Mounting Arm to Light Heads Align top of arm with arm light head base and press FIRML Y together . Arm should snap into position. (ref. fig. 25). Removing Arm from Light Heads T o remove light head from arm, “break” the arm at the upper most joint.
23 22 Light Operation Before you turn on the Pro lights, verify that the mode selector (flat position of black ring around red power button) is set to the P setting. Before you turn on the Elite lights, verify that the mode selector (flat position of black ring around red power button) is set to the E setting.
25 24 Bluefin Bulkhead Installation 1) Remove the Rear Plate. 2) Locate the power switch on the circuit boar d on the inside of the Rear Plate. Switch the appropriate switch (upper or lower) to ON. This activates power to the bulkhead. (ref. fig. 29) 3) Using a flat head screwdriver or coin, remove the Port Plug (r ef.
Bluefin Compact Monitor ID and Operation The External Monitor consists of three components • External Monitor - provides a 2.5” image of camera view • Clamp assembly - mounts monitor to back of housing • Cable - provides video signal from housing to External Monitor 1) Install monitor by first attaching clamp assembly to back of monitor .
Diving Without a Monitor Attached If you do not use the monitor you MUST de-activate power to the bulkhead before entering the water . T o de-activate Bluefin bulkhead: 1) Remove the Rear Plate 2) Locate the on/off switch on the inside of the Rear Plate.
31 30 Returning Products for Care W e highly recommend a factory annual service to maintain proper operation of your Bluefin Housing. 1) Before returning your Light & Motion product for care, please call or email our service department for a RMA number .
905-0187-A 300 Canner y Row • Monterey , CA 93940 (831) 645-1525 • Fax (831) 375-2517 www .uwimaging.com.
Een belangrijk punt na aankoop van elk apparaat Light & Motion VX2000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Light & Motion VX2000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Light & Motion VX2000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Light & Motion VX2000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Light & Motion VX2000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Light & Motion VX2000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Light & Motion VX2000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Light & Motion VX2000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
