Gebruiksaanwijzing /service van het product AE-500 van de fabrikant Linear
Ga naar pagina of 16
AE-500 T elephone Entr y & Access Control System PRINTER’S INSTRUCTIONS: INSTR,F ACILITY MANA GER,AE-500 - LINEAR P/N: 221000 E - INK: BLACK - MA TERIAL: 20 LB .
2 Contents Introduction The Model AE-500 T elephone Entry & Access Control System is designed for use as a primary access control device f or gated communities, parking garages, offi ce buildings, apartments, dor mitories, hotels/motels, commercial buildings and recreational f acilities with up to 250 residents or users.
3 Sys tem F eatur es DI S PLAY CABINET LOCK OPTIONAL PO S TAL LOCK S PEAKER KEYPAD LIGHTING KEYPAD MICROPHONE Your access control installation company has set this master password for this installation: _______________________ Use this password to enter programming mode.
4 P r ogramming with a Computer The AE-500’ s built-in progr amming interface can be accessed on-site (using a separate telephone line) or off-site using a computer with a modem and any Internet browser (if using Netscape, be sure J ava is installed).
5 Set ting up Multiple Units The system suppor ts up to se ven AE-500s connected to the same telephone line. Some telephone systems ma y only suppor t up to four units on the same telephone line. In multiple-unit installations each AE-500 m ust be assigned a unique unit number bef ore programming.
6 P r ogramming Over the T elephone The system can be programmed using a T ouchT one™ telephone. The telephone’ s ke ypad will act similar to the AE-500’ s local keypad. Connecting with a T elephone 1. Place a call to the telephone number of the line that AE-500 is connected to .
7 P r ogramming Refer ence PROGRAMMING CONTROL USAGE KEYSTROKES ENTER PROGRAMMING FROM LOCAL KEYP AD . . . . . . . . Press 0 and 2 then MASTER P ASSWORD ENTER PROGRAMMING FROM TELEPHONE . . . .Call, wait for tone then enter MASTER PASSWORD ESCAPE/CANCEL .
8 Resident Data P r ogramming Up to 250 resident names and telephone numbers can be set. Each resident entry is assigned a director y number . The director y numbers are the numbers visitors enter to hav e the system call the residents. ✦ NO TE: When entering resident names, programming the AE-500 from a computer is the pref erred method.
9 Entr y Code Programming Changing the Entr y Code Length The factory setting for the entry code length is 4 digits. It can be set to 2-6 digits. 1. If not already in Programming Mode, connect b y telephone or use the local ke ypad. Enter the master password and access prog ramming.
10 Wir eless T ransmit ter Pr ogramming Up to 500 wireless transmitters can be used with the system. T ransmitters can be ordered in pre-programmed b locks of sequential ID codes. Up to 16 blocks of transmitters can be used. T ransmitter bloc ks can be ordered with a F acility Code of 1-15 for b lock identifi cation if desired.
11 Wir eless T ransmit ter Pr ogramming (Continued) Activate a T ransmitter If a transmitter has been suspended, it can be activated again with these programming steps. 1. If not already in Programming Mode, connect b y telephone or use the local ke ypad.
12 Sys tem Options For most installations the f actory settings for the system will be appropriate. Y our installer may ha ve already customized some of the system settings .
13 Sys tem Options (Continued) Speaker T one on Relay Channel “A” Activation The factory setting will not cause the speaker to sound a tone when access is granted with Rela y Channel “A”. The tone can be turned on if desired. 1. If not already in Programming Mode, connect b y telephone or use the local ke ypad.
14 Sys tem Utilities Sev eral utility commands are av ailable f or the system. Utilities can be used to clear memory , display system information, and control the relays . Display Unit Number In multi-unit installations the unit number of each AE-500 can be displa yed.
15 AE-500 Operation Requesting Access with an Entr y Code • Residents hav e up to 40 seconds to ke y in their entr y code. • Up to eight seconds are allowed betw een each keystrok e.
Copyright © 2008 Linear LLC 221000 E T r oubleshooting System completely dead 1. Call installation company f or ser vice. Buzz on speaker 1. Call installation company f or ser vice. Buzz on telephone line 1. Call installation company f or ser vice. System will not answer an incoming call 1.
Een belangrijk punt na aankoop van elk apparaat Linear AE-500 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Linear AE-500 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Linear AE-500 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Linear AE-500 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Linear AE-500 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Linear AE-500 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Linear AE-500 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Linear AE-500 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
