Gebruiksaanwijzing /service van het product DVS-2400 van de fabrikant Linear
Ga naar pagina of 44
Black 0001 Black 0001 SUPER VISED WIRELESS SECURIT Y CONSOLE Installation & P rogramming Instructions SECURITY (760) 438- 7000 • FAX (760) 438- 7043 www.
Black 0002 Black 0002 INTRODUC TION CONGRATULATIONS f or selecting Linear’s DV S-2400 Security System. The DVS-2400 Console inc orporates many advanced and sophisticated features. The system can be expanded and cus tomized to fit th e installation’s specific needs.
Black 0003 Black 0003 TA B L E O F C O N T E N T S 1. THE DVS-2400 SEC URITY SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . 2 CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 DOOR/WIN DOW SENSORS . . .
Black 0004 Black 0004 1 . THE DVS-2 400 SECURIT Y S Y S TEM CONSOLE The DVS-2400 Console is the hear t of the system. It monitors all of the system’s wireless sensors and controls the alarm sirens. The Console constantly monito rs the condition of the system’s sensors, d isplaying which p rotected doors and windows are open or closed.
Black 0005 Black 0005 DOOR/WINDOW SEN SORS The DXS-31 & DXS-32 s ensors monitor doors and windows. They send radio signals to the Console. One type of signal is sent when the door or window is opened, and a different type of signal is sent when the door or window is c losed.
Black 0006 Black 0006 2. SECURIT Y S Y S TEM FL OOR PL AN EXAMPLE SYSTEM ◆ The example shows a typi cal DVS-2400 system. ◆ Any or all of the accessories sh own can be used. ◆ A total of 24 sensors (including keypads) c an be used with each Conso le.
Black 0007 Black 0007 3. T YPICAL S Y S TEM SE NSORS DOOR/WINDOW SEN SOR ◆ Sensor mounts on door or wind ow with adjacent magnet. ◆ Opening door or window mo ves magnet away, triggering sensor. ◆ Internal lithium batteries are monitored by the Console.
Black 0008 Black 0008 4. CONSOLE FE A TURES 1 24-HOUR BUTTONS ★ Pressing the [ FIRE ] button f or two seconds sou nds the fire siren and send s a “fir e” message t o a central m onitori ng statio n through the digital communicator (if the syste m is monitored).
Black 0009 Black 0009 10 AUXILIAR Y FUSE ★ Type 2AG, 1-amp f use. ★ Protec ts the extern al relay out put when used w ith wet conta cts (12 VDC switche d out). ★ Fuse will blow when load exceeds 1 amp. ✍ WARNING: For con tinued protection against the risk of fire, replace only with the s ame type and rating of fus e.
Black 0010 Black 0010 5. CONSOLE INS T ALL A TION CONSOLE LO CATION ✍ NOTE: Sensor signals m ust be able to reach the Console. ✔ Try to centrall y locate the Consol e. ✔ Keep Console awa y from large metal appliances. ✔ Maximum recommended sensor range is 400 feet (system teste d at 1000 feet).
Black 0011 Black 0011 EXTERNAL CONSOLE SPEAKER CONNECTION (OPTIONAL) ◆ An external cons ole speaker sounds system tones and alerts oc cupants with a loud siren during alarm. ◆ With the VB-2 module installe d, the Central Station can talk to the occupants through the external console speaker.
Black 0012 Black 0012 TELEPHONE LI NE CONNECTION (OPTIONAL) ◆ Connect the Console to the teleph one line if the system is monitored, requ ires 2-way audio, or requires telephone remote co mmand. ◆ Telephone ring & tip termin als are for connection to the incom ing telephone l ine.
Black 0013 Black 0013 CONSOLE POWER CONNECTION ◆ The Console is powe red by a low voltage plug-in transformer. ◆ Use up to 25 feet of 20 AWG o r larger two-conductor wire to conn ect the transformer to the Console. Route the power wires fro m the plug-in transformer to the Console.
Black 0014 Black 0014 6. BASIC CONSOLE PROG RAMMING ◆ In a new install ation, when power is first ap plied the Console’s master user code is “1234”. CREATE THE MASTER US ER CODE ✍ NOTE: Local programming must be entered on the Console’s keypad, not on a wireless rem ote keypad.
Black 0015 Black 0015 PROGRAMMING DIFFERENT SENSOR TYPES ◆ Follow the instructions on the previous page to select a sens or number to pro gram the sensor into. ✍ NOTE: A sensor can be programmed into mo re than one location. Be su re to choose an unused sensor number.
Black 0016 Black 0016 7 . BASIC SENSOR INS T ALL A TION ◆ Each accessory sensor is pack aged with its own set of installation instructio ns specific to the model of se nsor. ◆ Refer to the sen sor’s instructions for details on installing, operati ng, and testing of the senso r.
Black 0017 Black 0017 DXS-31 & DXS-32 DOOR/WINDOW SENSORS ◆ The DXS-31 and DXS-32 sens ors can be used to monitor doors, wi ndows, cabine ts, crawl spac e doors, gates, fr eezer doors, and m any other moving objects that c ould be used for intrusion or need to b e monitored.
Black 0018 Black 0018 8. CUS T OMIZING THE CONSOLE ◆ The Console can be customized for th e specific installation. ◆ A label sheet with sensor location names is provided with the Co nsole.
Black 0019 Black 0019 9. CONSOLE OPERA TING MODES OFF MODE ◆ Use this mode to disarm the burglary portion of the system. ◆ Switching to Off Mode stops any alarms in progress. ◆ The 24-hour func tions are still active in Off Mode and can be triggere d by pressing the [ FIRE ] or [ EMERGENCY ] button.
Black 0020 Black 0020 HOME MODE ◆ Use this mode when sleeping or when anyone is staying i nside. ◆ Home Mode causes an instant alarm when any perimeter sensor is triggered. ◆ Home Mode causes a delayed alarm when any exit/entry sensor is triggered (except in Home Instant Mode when they are instant).
Black 0021 Black 0021 AWAY MODE ◆ Use this mode when no one will be staying home. ◆ Each burglary sensor can trigger the siren once per armi ng period. ◆ Away Mode causes an instant alarm when any perimeter sensor is triggered. ◆ Away Mode causes a delayed alarm when any exit/entry sensor is triggered.
Black 0022 Black 0022 TEST MODE ◆ Even though this is a self-monitoring supervised system, the National Bu rglar and Fire Alarm Association recommends th at all security systems shoul d be tested manuall y on a regular basis. ◆ The Consol e must be in Off Mode before g oing to Test Mode.
Black 0023 Black 0023 1 0. S Y S TEM TROUBLE INDICA TIONS ◆ The DVS-2400 C onsole is a self -monitoring supervised wireless system. ◆ If the Console detects a problem with any of the supervised sy.
Black 0024 Black 0024 1 1 . CUS T OMIZING THE S Y S TEM ◆ Adding additional sens ors will increase the protection provided by the system. ◆ All ground-level perimeter o penings and accessible upper-st ory openings need protection. ◆ Motion detectors can protect interior areas and areas where valuables are kept .
Black 0025 Black 0025 MAKING A SEN SOR A 24-HOUR DOOR CH IME ◆ Sensors can be programmed to cause the Console to chime an y time they’re activated.
Black 0026 Black 0026 MAKING A SENS OR PERFORM A DIFFE RENT FUNCTION ◆ Sensors can be reprogrammed to pe rform differe nt sensor func tions. ◆ The sensor must hav e already been lear ned by the Console (see “Adding Sensors to th e System” for details).
Black 0027 Black 0027 1 2. ADV ANCED PROGRAMMING ◆ To perform any of th e advanced programming steps, the Console must be in the Setup Mo de. ◆ Each programm ing function is performe d with similar keystr okes.
Black 0028 Black 0028 CHANGING A SENSORS SUPERV ISION ◆ When a sensor is pr ogrammed, the Console sets all stationary sensors as supervised, and all portable se nsors as non-s upervise d. ◆ The Console expects h ourly status transmissions from any sensor programmed as supervised.
Black 0029 Black 0029 FIRE SIREN TIME ◆ The factory-set fire siren time is five minu tes. ◆ The fire siren time c an be adjusted from one to 30 minutes. AUTOMATION OUTPUT TIME ◆ The factory setting causes th e Automation Output to toggle betwee n on and off with each activation.
Black 0030 Black 0030 SILENT BURGLAR Y ALARMS ◆ The factory setting causes audible burglary alarms. ◆ Alternately, the Console can be pr ogrammed for silent burglary alarms. SILENT E MERGENCY ALARMS ◆ The factory setting causes audible emergency alarms.
Black 0031 Black 0031 AUTOMATION OUTPUT MO DE DURING ALARM ✍ NOTE: For the Automation Output to activate during an alarm, t hat function must be enabled with Programming Step 71 or 72. ◆ If the Automation output is p rogrammed to activate during an alarm, it can be progr ammed to flash or be ste ady.
Black 0032 Black 0032 AUTOMATION OUTPUT WHILE ARMED ◆ The factory setting causes the Console’s Automation Output to activate when pressing the [ (A) ] key, or wh en it’s triggered with a two-button remote control. ◆ In addition, the Cons ole can be progr ammed to activate the Auto mation Output when th e system is armed.
Black 0033 Black 0033 ADDITIONAL USER CODES ◆ The Console can be programmed with fi ve restricted user codes an d one page alert user code. ◆ The restricted user codes o perate the system as usual, but cannot ac cess Setup Mode.
Black 0034 Black 0034 1 3. COMMUNICA T OR PROGRAMMING SETUP MODE ◆ To perform any of the communicator programming steps, the Co nsole must be in the Setup M ode.
Black 0035 Black 0035 GENERAL COMMUNICATOR OPTIONS COMMUNICATOR ENABLE ◆ The factory setting for the Console disables the communicator. If the system is going to be a non-monitored, lo cal alarm only, leav e the communicator disabl ed.
Black 0036 Black 0036 CALL LIMIT ER ◆ The factory setting for the call limiter is OFF. This allows the communicator t o report burglary alarms, once for each sensor, as many times as they are tr iggered. ◆ Optionally, the Console can be program med to only allow five burglary reports total per arming period.
Black 0037 Black 0037 COMMUNICATOR REPORTING OPTIONS REPORTING FORMAT ◆ The factory setting causes the communicator to report using the 4 by 2 for mat. This format allows four-digit account number s from 0000 to 9999 and p rovides two-digit alarm codes.
Black 0038 Black 0038 ACCOUNT NUMBER ◆ The communicator’s acc ount number entered must be 4-digits long. ◆ The factory setting for the account number is 0000. ◆ Enter an account number from 0000 to 9999 . PRIMARY TELEPHONE NUMBER ◆ The primary Central Station te lephone number can be up to 20-dig its long.
Black 0039 Black 0039 REPORT CONSOL E TROUBLE ◆ The factory setting does not report Conso le trouble events to the Central Statio n. ◆ Alternately, the commu nicator can be programmed to report Con sole trouble events. These include all conditions t hat light the Console’s BATTER IES or TROUBLE indicator.
Black 0040 Black 0040 COMMUNICATOR REPORTING CO DES ◆ The two-digit commu nicator reporting co de for each event has a factory set valu e. These values may be customized to fit the specific installation and the reporting requirements of the Central Station monitoring the sy stem.
Black 0041 Black 0041 FORCE ARMING REPORTING CODE ◆ Programming Step # 258 ◆ The factory set reporting code for force armin g is “65” (Code 574 with Ademco ). ◆ Any value from 0-9 9 can be programm ed for this event (0 = no report). ✍ NOTE: For force arming reporting, force arming reports must be enabled.
Black 0042 Black 0042 4 BY 2 FORMAT POINT ID REPORTING CODES 4 BY 2 FORMAT POINT ID ALARM REPO RT CODES ◆ Refer to the 4 by 2 Form at Point ID Reporting Code table to view/edit the alarm reporting codes for each of the 24 sensors. The communicator will send thes e codes if Point ID is enabled and any sensor triggers an alarm.
Black 0043 Black 0043 POINT ID RE PORTING CODES STEP # PROGRAMMING FUNCTION POSSIBLE VALUES FACTORY VALUE INSTALLATION VALUE 210 SEN SOR 1 ALARM REPORT CO DE 0 - 99 11 211 SEN SOR 2 ALARM REPORT CO DE.
Black 0044 Black 0044 IMPOR T ANT INFORMA TION LINEAR LIMITED WARRANTY This Linear product is warranted against defects in material and workmanship for twelve (12) months.
Een belangrijk punt na aankoop van elk apparaat Linear DVS-2400 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Linear DVS-2400 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Linear DVS-2400 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Linear DVS-2400 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Linear DVS-2400 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Linear DVS-2400 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Linear DVS-2400 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Linear DVS-2400 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
