Gebruiksaanwijzing /service van het product VMC-1 van de fabrikant Linear
Ga naar pagina of 24
VMC1 V ideo Security Intercom System f or the Home Rough - In Instructions USA & Canada (800) 421-1587 & (800) 392-0123 (760) 438-7000 - T oll Free F AX (800) 468-1340 www .
Keep this manual in a safe place for future reference. T o replace this manual, download available from Linear W eb site:www .linearcorp.com Read Instructions - All saf ety and operating instructions should be read bef ore installing or operating the VMC1 Video Intercom system.
1 ✔ DO ensure that all instructions hav e been f ollowed bef ore power is applied to system. The installation shall be carried out in accordance with all applicable installation rules. ✔ DO use only Cat-5 & RG-6 and specifi ed wires called out in these instructions.
2 T able of Contents Block Dia gram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Rough-in Kit . . . . . . .
3 Block Diagram - + 1 VOLUME PRIV MON MUS CLEAR HOUSE DOOR AUX 23 4 5 6 7 AM ANTENNA FM ANTENNA MASTER ST A TION TE6D PO WER SUPPL Y H628 D A T A HUB ROOM ST A TION DOOR ST A TION DEDICA TED POWER VID.
4 Introduction VMC1MB TE6D 101093 226804 250106-2 233103 The VMC1H installation rough-in prepares the home to accommodate the video intercom system. A VMC1MB mounting brac ket is necessary for the Master Station. Room stations and the Alloy Color V ideo Door Station (VMC1VDS) can be mounted directly onto fi nished walls.
5 Materials Required T ools Most are required for purposes of this installation, but may vary according to installer preferences. PO WER DRILL WITH 1” A UGER WIRE STRIPPERS/CUTTER T APE MEASURE PHILLIPS SCREWDRIVER 14/18 GA UGE WIRE 110 PUNCH-DO WN T OOL CA T -5 CABLE DR YW ALL SA W HAMMER LEVEL 0-M 0.
6 Overview The VMC1 S ystem Designed for installation in new homes, the VMC1 is a Whole House Color Video Security Intercom system that pro vides room to room communication, multiple camera support, basic home automation controls, and video security for mid to large residential applications.
7 Wiring Information Cables and Wir ing Excellent locations to run cables include: • Roof space • False ceilings/ bulkhead area • Through and/or around external walls • Under fl oor s (subject to access being available) • Underground in conduit ✓ NO TE: K eep Intercom cab les far from any A C wiring.
8 Master Station Rough-In VMC1MB Master Station Mounting Br ack et The VMC1MB mounts fl ush with the wall stud and holds the Master Station and P ower Supply (See Figure 1). Position the VMC1MB at a suggested height of 4-1/2 to 5-1/2 feet from the fl oor to center of the unit.
9 Master Station Rough-In VMC1MB Installation - Finished W all Cut out an opening in the drywall (Height 7 -1/4” x Width 1 1”) but do not cut right up against the w all stud. Allow 5/8” clearance between drywall opening and stud. This ensures that drywall will o verlap bracket (See Figure 2).
10 Room Station Rough-In Room Station Mounting The Room Stations are normally mounted at a height from the fl oor of: 4-1/2’ to 5’ . The Room Stations are not designed to be installed outdoors. Room Station Installation - Unfi nished W all For an unfi nished wall it is recommended that the VMC1HR rough-in enclosure be used.
11 Door Station Rough-In VMC1VDS Door Station Rough-in The VMC1VDS is a metal door station with a 90 degree horizontal viewing area. It is normally mounted at a height from the fl oor of: 55” – 60” . When installing the VMC1VDS be aware of the camera location and the direction of sunlight and other ambient light.
12 VMC1VDS-S/BZ Door Station Rough-in The VMC1VDS-S and VMC1VDS-BZ incorporate a wide angle 120 degree horiz ontal viewing camera into a Door Station. It is normally mounted at a height from the fl oor of: 55” – 60” . Installation of this unit on an exterior wall requires 4 screws and anc hors (See Figure 6).
13 Po wer Supply Rough-In TE6D P ow er Supply The P ower Supply unit is pre-wired and self contained, and the wires are tuc ked inside. T o access connection wires, open the P ower Supply unit by removing four screws as shown in Figure 6.
14 Po wer Supply Rough-In Figure 7 - TE6D P ower Supply Wiring P ow er Supply Wir ing 1. R un a 14 AWG 120 V AC power cable (including ground) from a dedicated 15-amp circuit breaker to the Master Station Mounting Brac ket location. The VMC1 requires a dedicated power source so there’ s no interference from other equipment.
15 Data Hub Wiring TIA-568A WIRING ST ANDARD D A T A HUB RJ-45 MODULAR PLUG Cat-5 WIRE COLOR Pin 1 White/Green Pin 2 Green Pin 3 White/Orange Pin 4 Blue Pin 5 White/Blue Pin 6 Orange Pin 7 White/Brown Pin 8 Brown Figure 8. H628 Data Hub Wiring H628 D ata Hub The H628 Data Hub is used to connect eac h station to the Master Station.
16 Antenna Installation Radio Antennas VMC1 requires two antennas, one for AM and one for FM reception. The AM antenna is a 25-foot wire the FM antenna is a 25-foot length of coax with a “T” shaped wire dipole at one end that attac hes between rafters in the attic.
17 Auxiliary Output Rough-In Figure 10. Electric Door Strike Wiring Chime Activ ated Control Output Rough-In The Chime Activated Control Output allows for any number of security related automation functions including 1 0 available door c himes. T o connect an auxiliary Chime refer to Figure 1 0.
18 Appendix A – A vailable Components System Master Station with 5.6” TFT LED color screen suppor ting up to 20 remote stations. P oint-to-P oint, P oint-to-Group and All Call intercom with hands free response.
19 Ple xiglas weather shield increases the weather resistance of VMC1VDS to IP31 Smoke Color (VDSWS-T) Appendix A – A vailable Components Ple xiglas weather shield increases the weather resistance of VMC1VDS-BZ/S to IP31 Clear (DSWS) Nightstand station.
20 Appendix A – A vailable Components Model H275 Univ ersal Brack et for Data Hub Installation Indoor Bo x Color Camera (left) & Color Video Cameras w/nite vision (r ight) (ML TL2DN49IR) Rough in kit f or the VMC1 Master .
21 Miniature door / window tr ansmitter (DXS-32) 2-Channel Receiv er (DXR-702) 12V Control Output s witched 110V outlets for lights and other “notifi cation” devices Remote T ur n On for Lights A C1 (1 outlet) AC3 (2 outlets) MFG: Xantec/Niles Wire Rela y The 284 Leaded Accessor y Rela y is a 5 amp F or m C relay with wire leads pre-attached.
2 - Y ear Limited Warr anty Linear LLC war rants these products to be free of defects for 2 years. The warranty period begins on either (a) the date of purc hase or installation date of this product or (b) the date of closing on a new residence in whic h this product was originally installed.
Een belangrijk punt na aankoop van elk apparaat Linear VMC-1 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Linear VMC-1 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Linear VMC-1 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Linear VMC-1 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Linear VMC-1 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Linear VMC-1 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Linear VMC-1 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Linear VMC-1 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
