Gebruiksaanwijzing /service van het product Direct Vent Freestanding Stove van de fabrikant Lopi
Ga naar pagina of 42
Featuring the Burner • Direct Vent Freestanding Stove • Natural Gas or Propane • Vent Horizontally or Vertically • Standard Residential • Mobile Home Approved Tested and Listed by OMNI-Test Laboratories, Inc. Beaverton, Oregon Report # 028–S–50-5 ANSI Z21.
2 Introduction Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Introduction We welcome you as a new owner of a Lopi Sturbridge stove. In purchasing a Sturbridge you have joined the growing ranks of concerned individuals whose selection of an energy system reflects both a concern for the environment and aesthetics.
Table of Contents 3 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Introduction Introduction & Important Information ................2 Safety Precautions Safety Precautions ......................................4 Specifications Features .............
4 Safety Precautions Travis Industries 1 0 0 - 0 1 1 4 2 4050114 • IF YOU SMELL GAS: * Do not light any appliance * Extinguish any open flame * Do not touch any electrical switch or plug or unplug a.
Safety Precautions 5 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 • Do not place clothing or other flammable items on or near the heater. Because this heater can be controlled by a thermostat there is a possibility of the heater turning on and igniting any items placed on or near it.
6 Specifications Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Features: - Ember Fyre™ Burner for "Wood Fire" Look - Works During Power Outages (millivolt system) - High Efficiency - Optiona.
Installation (for qualified installers only) 7 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Installation Warnings: ! Failure to follow all of the requirements may result in property damage, bodily injury, or even death.
8 Installation (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Installation Hints: • If converting to LP, convert the appliance prior to installation.
Installation (for qualified installers only) 9 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Heater Placement Requirements • Heater must be installed on a level surface capable of supporting the heater and vent • Due to the high temperature, the heater should be located out of traffic and away from furniture and draperies.
10 Installation (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Gas Line Installation ! The gas line must be installed in accordance with all local codes, if any; if not, follow current ANSI Z223.
Installation (for qualified installers only) 11 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Vent Requirements ! Always maintain the required 1” clearance (air space) to combustible materials to prevent a fire hazard. Do not fill air spaces with insulation.
12 Installation (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Approved Vent Configurations Restrictor Position • A restrictor is built into the appliance to control the flow rate of exhaust gases. This ensures proper flames for the wide variety of vent configurations.
Installation (for qualified installers only) 13 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Measuring Vent Lengths Vent Horizontal Run Vent Horizontal Run is measured from the start of the horizontal section to the end of the termination.
14 Installation (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Approved Venting Configurations for Horizontal Terminations • 12 ’ Maximum System Height • 15 ’ Maximum Offset • The termination must fall within the shaded area shown in the chart.
Installation (for qualified installers only) 15 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Approved Venting Configurations with a Vertical Termination • Remove the diffuser plate (see “ Diffuser .
16 Installation (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 V e n t T e r m in a t io n R e q u ir e m e n ts ( se e illu s tr a tio n b e lo w) ! Venting terminals shall not be recessed into a wall or siding.
Finalizing the Installation (for qualified installers only) 17 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Finalizing the Installation ! Make sure the gas control valve is “ OFF ” and the heater is cool prior to conducting service. 1 Remove the glass (see page 19) 2 Install the log set and coals (see page 21).
18 Finalizing the Installation (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 6 Let the heater burn for thirty minutes. Adjust the air shutter, if necessary, to achieve the correct looking flame (see the illustration below).
Finalizing the Installation (for qualified installers only) 19 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Glass Removal WARNING : Make sure the gas control valve is “OFF” and the heater is cool prior to conducting service. Lift the stove top off the stove and place it aside.
20 Finalizing the Installation (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Glass Frame Removal and Installation (continued) The spring pin can come loose from the latch assembly. This occurs when it is turned 1/4 turn when it is disengaged.
Finalizing the Installation (for qualified installers only) 21 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Log Installation ! Make sure the gas control valve is “ OFF ” and the heater is cool prior to conducting service.
22 Operation Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Before You Begin Warning: Read this entire manual before you use your new stove (especially the section "Safety Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily injury, or even death.
Operation 23 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Starting The Pilot Flame The pilot flame is required to ignite the main burners (it also plays a safety role). It should be left on once lit. It will stay lit unless the gas control valve is turned to "OFF".
24 Operation Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Starting the Stove for the First Time Fumes from the Painted Surfaces Curing Burn the heater at a medium setting for approximately one hour the first time. This will cure the painted surfaces. Fumes from the paint curing and oil burning off the steel may occur.
Operation 25 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Adjusting the Blower Speed (optional) The blower helps transfer the heat from the heater into the room. It will not turn on until the heater is up to temperature (approximately 10 minutes after starting).
26 Maintenance (for qualified service personnel only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Maintaining Your Stove's Appearance Painted Surfaces • Painted surfaces should be cleaned with a duster (make sure the stove is cool). If scratches occur, lightly sand the area with fine sandpaper.
Maintenance (for qualified service personnel only) 27 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Troubleshooting Table Problem: Possible Cause: Don't Call for Service Until You: Pilot Will Not L.
28 Maintenance (for qualified service personnel only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 How this Stove Works ! This stove was designed with safety as the primary concern. Many of the components inside this stove are for safety purposes. Therefore, only certified gas service technicians should service this stove.
Maintenance (for qualified service personnel only) 29 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Wiring Diagram Caution : Label all wires prior to disconnection when servicing controls.
30 Safety Label Travis Industries 1 0 0 - 0 1 1 4 2 4050114 The safety (listing) label is on the back of the stove. A copy of the safety label is shown below. Sturbridge V ented Gas Fireplace Heater Report No. 028-S-50-5 Certified for USA T ested to: ANSI Z21.
Limited 7 Year Warranty 31 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 To register your TRAVIS INDUSTRIES, INC. 7 Year Warranty, complete the enclosed warranty card and mail it within ten (10) days of the appliance purchase date to: TRAVIS INDUSTRIES, INC.
32 Optional Equipment (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Optional Accessories • Aroma-Therapy Tray (S.N. 3105-12739 or greater) 98500385 • Double Doors, Ne.
Optional Equipment (for qualified installers only) 33 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 LP Conversion Instructions Install the conversion kit prior to installing the gas line to ensure proper gas use. 1 Remove the glass (see page 19). Remove the log set (if installed - page 21) 2 Remove the burner (see illustration below).
34 Optional Equipment (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 3 Follow the directions below to remove the natural gas orifice. Apply thread sealant to the LP orifice ( it has "1.2" stamped on it) and tighten in place with a 1/2" open end wrench.
Optional Equipment (for qualified installers only) 35 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 5 Remove the regulator from the front of the gas control valve. Replace with the propane regulator, using the new gasket and screws included with the regulator.
36 Optional Equipment (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Blower (part # 99000154) WARNING: Turn the gas control valve to off and make sure the appliance has fully cooled prior to conducting service .
Optional Equipment (for qualified installers only) 37 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 3 Attach the wiring harness following the directions below (do not plug in the power cord at this time). Do not plug the heater in until installation is complete.
38 Optional Equipment (for qualified installers only) Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Fireback (Part # 99900146) WARNING: Turn the gas control valve to off and make sure the appliance has fully cooled prior to conducting service . • Make sure the heater is shut off (pilot out) and fully cool prior to installation.
Optional Equipment (for qualified installers only) 39 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Stone or Cast Inserts WARNING: Turn the gas control valve to off and make sure the appliance has fully cooled prior to conducting service .
40 Installation Addenda Travis Industries 1 0 0 - 0 1 1 4 2 4050114 ADDENDUM #1 Class A Chimney Conversion Kit Simpson Duravent provides a conversion kit for those wishing to use an existing wood stove chimney to vent this direct vent stove. The illustration below gives an overview of this type of installation.
Installation Addenda 41 Travis Industries 1 0 0 - 0 1 1 4 2 4050114 ADDENDUM #2 Masonry Chimney Conversions • Follow the requirements and use the equipment listed in the illustration below to install this appliance into an interior masonry chimney.
42 Index Travis Industries 1 0 0 - 0 1 1 4 2 4050114 Approved Vent Configurations .......................... 12-15 Adjusting the Blower Speed ..............................2 5 Adjusting the Flame Height ...............................2 4 Air Shutter Adjustment .
Een belangrijk punt na aankoop van elk apparaat Lopi Direct Vent Freestanding Stove (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lopi Direct Vent Freestanding Stove heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lopi Direct Vent Freestanding Stove vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lopi Direct Vent Freestanding Stove leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lopi Direct Vent Freestanding Stove krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lopi Direct Vent Freestanding Stove bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lopi Direct Vent Freestanding Stove kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lopi Direct Vent Freestanding Stove . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
