Gebruiksaanwijzing /service van het product EP-60R van de fabrikant Lowrance electronic
Ga naar pagina of 48
1 Pub. 988-0154-432 EP-60R Fuel Flow Electronic Sensor Installation, Configuration and Calibration Instructions This document shows how to install an EP-60R Fuel Flow sensor and how to connect it to a NMEA 2000 ® network.
2 Some sonar or GPS display units may require a software upgrade to display NMEA 2000 data correctly. For free software upgrades or additional information on the LowranceNet NMEA 2000 ® network system, visit our web si te, www.lowrance.com. The EP-60R consists of a red cabl e connector and the sensor module.
3 LowranceNET Node Kit for a NMEA 2000 network. Includes a 2-foot extension cable, T connector and two 120-ohm terminators. For complete instructions on se tting up a new NMEA 2000 network or expandin.
4 Cut the fuel hose where you intend to install the EP-60R sensor. Slide a clamp over the hose coming from the tank, then push the hose onto the bottom (inlet) hose barb. Seat the hose flush against the sens or housing, then tighten the hose clamp. Attach the hose leading to the engine on the top (outlet) barb in the same way.
5 Connecting to a NMEA 2000 Network A NMEA 2000 network is a communications link between two or more devices that transfer NMEA 2000 in formation. LowranceNET is the NMEA 2000 networking system develo ped by Lowrance Electronics. A NMEA 2000 network functions like the phone wiring in a house.
6 NMEA 2000 network node located at the end of a NMEA 2000 backbone. NOTE: If you have a double T Connector on your network that is not attached to a device, you must cap the unused connector with a NMEA 2000 cap. This will protect the pin connectors from corrosion.
7 In this example, a new device is added to the N ME A 2000 bus by installing a T conn ector between a T connector and a terminator at the end of the backbone (network bus).
8 Notes.
9 LMF-200: EP-60R Configuration & Calibration This section covers how to use th e EP-60R Fuel Flow with a LMF-200 Multi-function gauge. NOTE: You will notice the LMF-200 does not have an Exit key. Menus will time out after a preset amount of time (3, 5, 10 or 15 seconds).
10 3. Select the tank you want to set up and press MENU , which will open the Tank Size window. 4. Use the UP and DOWN keys to input the number of gallons the tank will hold and press MENU . Repeat steps 3 and 4 for each additional tank. After all tanks have been set up, you will be directed to the m ain display.
11 3. Select U N C FG FF and press MENU . The following message will appear: Hit Menu to Cfg Flow Sns. Press MENU and the Configuration options menu will appear. NOTE: If your unit is set to a sing le-engine configuration, the Configuration Options menu will not appear when you are configuring a fuel flow.
12 If all fuel flows configured (Configuration name unav ailable): 1. Press MENU , use the UP and DOWN k e y s t o s e l e c t S YSTEM S ETUP and press MENU . 2. Highlight B. D EVICES and press MENU . The Bus Devices list will appear. 3. Select the Port FFlow and press MENU .
13 5. You will be taken back to the Bus Devices list, where the fuel flow you selected (formerly Port FFlow) w ill be listed as Stbd FFlow. If the newly configured fuel flow is not shown, refresh the Bus Devices list. Reset The Reset command in the Fuel Flow level menu will clear the sensor’s configuration and calibration settings.
14 To customize Fuel Manage r page: 1. With the Fuel Manager page displayed on the main display, press MENU , select C USTOMIZE and press MENU . 2. Highlight USD (Fuel Used) and press MENU . If your unit is configured for more than one tank, the Select Tank menu will appear.
15 9. The Recalibration (The Recal?) menu will appear with two options: Yes and No. Select Y ES and press MENU . NOTE: If you do not have the fuel rema ining source set to Eng/FFlow, the recalibration message will not appear. 10. The Filled Quantity window will appear.
16 add fuel to a tank without completely filling it up, you must use the Partial Fill command. This will ensure the fuel information in the EP- 60R stays consistent with the amount of fuel actually in the tank. To use Partial Fill: 1. Press MENU , use the UP and DOWN k e y s t o s e l e c t S YSTEM S ETUP and press MENU .
17 To Reset Trip Fuel (Rst trip f) 1. Press MENU , use the UP and DOWN keys to select S YSTEM S ETUP and press MENU . Highlight F UEL MNGR and press MENU . 2. Select R ST TRIP F (Reset Trip F uel) and press MENU . The Select Engine menu will appear with up to four opti ons.
18 6. Use the UP and DOWN keys to input the desired percentage of tank capacity and press MENU . Let the menus time out to return to the main display. NOTE: To turn off a fuel warning, repeat Steps 1-4, then select O FF from the Level Percentage window mentioned in Step 5.
19 Autoscroll feature if you want the pages to automatically scroll across the screen. Refer to your LMF -200 manual for more information about Autoscroll.
20 menu will appear, allowing you to display data from a single engine or show data from all engines. (If you select F UEL R ANGE (RNG) or if your unit is configured for one engine, you will be taken back to the main display.) 5. Select the desired engine or, to display data from all engines, highlight Vessel and press MENU .
21 LMF-400: EP-60R Configuration & Calibration This section covers how to use th e EP-60R Fuel Flow with a LMF-400 Multi-function gauge. LMF-400 Multi-function Digital gauge.
22 Boat Setup Reset If you want to access the Setup scr een (Boat Setup) after an engine- tank configuration has been chosen you will have to reset the configuration to default settings. To reset engine-tank config uration: 1. Press MENU , highlight S YSTEM S ETUP and press ENTER .
23 1. Press MENU , use the UP and DOWN k e y s t o s e l e c t S YSTEM S ETUP and press ENTER . 2. Highlight B US D EVICES and press ENTER . The Bus Devices list will appear. Bus Devices highlighted in the System Setup menu (left). Searching Bus Devices window (center) wi th Bus Devices list (right).
24 flow to free up its configuration name. If all three fuel flows are configured, which means there is no configuration name available, follow the first set of instructions. If the desired configuration name is available, follow the second set of instructions .
25 EP-60R Fuel Flow Calibration The factory calibration settings for the EP-60R Fuel Flow should be within 3 percent, so calibration will not be necessary in most cases. NOTE : The Fuel Remaining Source must be set to fuel flow for the unit to correctly display fuel level info rmation.
26 2. Press MENU , use the UP and DOWN k e y s t o s e l e c t S YSTEM S ETUP and press ENTER . 3. Highlight F UEL S ETUP and press ENTER . 4. Select R EFILL T ANK and press ENTER . If your unit is configured for more than one tank, the Select Tank menu will open.
27 2. Highlight B US D EVICES and press ENTER . Highlight the fuel flow you want to reset and press ENTER . 3. Select R ESET C AL from the fuel flow menu and press ENTER . The following message will appear: Press Enter to reset the Calibration . 4. Press ENTER to set calibration back to de fault settings.
28 NOTE: When using the Partial Fill command, you will only be able to input into the gauge, an amount of fuel less or equal to the fuel used figure. The unit will not allow you to enter a fuel amount greater than the fuel used figure. 4. Use the UP and DOWN keys to input the amount of fuel added to the tank and press ENTER .
29 To reset seasonal fuel: 1. Press MENU , select S YSTEM S ETUP and press ENTER . 2. Highlight F UEL S ETUP and press ENTER . 3. Select R ESET S EA SONA L and press ENTER . The Select Engine menu will appear with up to four options. (If you have one engine, the reset seasonal fuel message (Step 4) will appear.
30 To set an Engine Warning (A larm): 1. Press MENU , use the UP and DOWN keys to highlight S YSTEM S ETUP , and press ENTER . 2. Highlight E NGINE W A RNINGS and press ENTER . The Engine Warnings menu will appear with up to five options, including Off and All Engines.
31 To customize Single Digital page : 1. After the Single Digital page has been added to the page screen rotation, use the ENTER and EXIT keys to display it on the main screen. 2. Press MENU , use the UP and DOWN keys to select C USTOMIZE and press ENTER .
32 data from a single engine or from all engines on the vessel. (If you select F UEL R ANGE or if your unit is configured for one engine, you will be taken back to the Position menu.) 5. Select the desired engine or, to display data from all engines, highlight Vessel and press ENTER .
33 Display Unit: EP-60R Configuration & Calibration All NMEA 2000 capable Lowrance sonar and sonar/GPS combo display units can be used to configure and calibrate your EP-60R Fuel Flow sensor on a NMEA 2000 network. The LMS-525cDF is one of many Lowrance display units that may be used to configure an EP-60R Fuel Flow sensor.
34 Bus Setup highlighted on the NMEA 2000 menu (left). Bus Setup selected on Networking menu (right). The Engine-Tank Configuration and Tank Select menus as well as the Tank Size dialog box are located on the bottom half of the Bus Configuration menu.
35 Setting Engine-Tank Configuration: 1. Press MENU twice, highlight NMEA 2000 or N ETWORKING and press ENTER . 2. The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Management, NMEA 2000 Alarms, Waypoint Sharing and Backlight Synchronization.
36 menu. To configure or calibrate most devices, you will select it on the NMEA 2000 Devices list and press ENTER . This will open its Device Configuration menu. Bus Configuration menu with five items displayed on the NMEA 2000 Devices list. Engine-Tank Configuration and Tank Select menus are at the bottom of the screen.
37 EP-60R Fuel Flow Configuration When configuring your fuel flow, you will open its Device Configuration menu where you can access the Location and Advanced Options menu.
38 5. Highlight the device and press ENTER . The Device Configuration menu will open. The device name will be reset to its default setting. Press EXIT repeatedly to return to the main display. Location The Location menu allows you to se lect a configuration name that matches the location of the engine connected to your fuel flow sensor.
39 Fuel Management highlighted on Networking menu (left). Fuel Management menu (right). Fuel Management Menu The Fuel Management menu gives you access to the following options: Tank Location, Fuel Added, Add Fu el, Fill Tank, Engine Select, Reset Calibration, Reset Trip and Reset Seasonal.
40 If you filled up the tank: A. Press the F ILL T AN K button and press ENTER . The following message will appear: Are you sure you wish to Fill Tank? Press ENTER . Another message will appear: Do you wish to re-calibrate the device? Highlight N O and press ENTER .
41 4. Highlight F ILL T AN K and press ENTER . The following confirmation message will appear: Are you sure you wish to Fill Tank? NOTE : You must use the unit’s Fill Tank command when filling your fuel tank to keep the fuel flow updated with correct information on the amount of fuel in the tank.
42 To Reset Calibration: Choosing the Reset Calibration command will switch fuel flow calibration settings back to factory defaults. 1. Press MENU twice, select NMEA 2000 or N ETWORKING and press ENTER . 2. Highlight F UEL M AN AG EM E N T and press ENTER .
43 Displaying data from fuel flow The Overlay Data function will be used to show EP-60R Fuel Flow data on your unit's main display. To add ov erlay data from the EP-60R: 1. Press MENU , highlight O VERLAY D ATA and press ENTER . 2. Select (P RESS ENT TO ADD …) and press ENTER .
44 Alarm Status Tab The Alarm Status tab is the second tab at the top of the NMEA 2000 Alarms page. When an alarm has been set for a device, the alarm and its current status will be shown on the Alarm Status window. To view Alarm Status: 1. Press MENU twice, select NMEA 2000 or N ETWORKING and press ENTER .
45 Notes.
46 Notes.
47 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRAN CE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person wh o purchases this p roduct as a consumer item for personal, family or household use.
48 How to Obtain Service… …in the USA: Contact the Factory Customer Se rvice Department. Call toll-free: For Lowrance: 800-324-1356. For Eagle: 800-324-1354 8 a.
Een belangrijk punt na aankoop van elk apparaat Lowrance electronic EP-60R (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lowrance electronic EP-60R heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lowrance electronic EP-60R vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lowrance electronic EP-60R leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lowrance electronic EP-60R krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lowrance electronic EP-60R bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lowrance electronic EP-60R kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lowrance electronic EP-60R . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
