Gebruiksaanwijzing /service van het product X58DF van de fabrikant Lowrance electronic
Ga naar pagina of 64
Pub. 988-0105-951 www.lowrance.com X51 and X58DF Fish-finding & Depth Sounding Sonars Installation and Operation Instructions.
Copyright © 2002 Lowrance Electronics, Inc. All rights reserved. Lowrance ® is a registered trademark of Lowrance Electronics, Inc. Marine-Tex is a trademark of Illinois Tool Works Inc. Lowrance Electronics may find it necessary to change or end our policies, regulations, and special o ffers at any time.
i Table of Contents Introduction .................................................................................. 1 Capabilities and Specificat ions: X51 an d X58DF ........................ 1 Installation ............................................
ii System Setup ............................................................................ 44 Backlight s ................................................................................ 44 Display Co ntrast .........................................
1 Introduction Thank you for buying a Lowrance sonar! Your unit is a high-quality sonar designed for both professi onal and novice fishermen. All Lowrance sonars have an automatic mode that finds and displays the bottom, fish, underwater structure and more – right out of the box.
2 Sonar Frequency: ...................... 200 kHz (o r 50/200 kHz – X58DF only). Transducers: .................. A dual-fr equency Skimmer transducer comes packed with the X58DF. It has 35 ° /12 ° cone angles. Single frequency models for X51 with a 20 ° cone angle are sold separately.
3 both single- and dual-frequency Skimmer transducers. Please read all instructions before proceed ing with any installation. The smaller single-frequency Skimmers typically use a one-piece, stainless steel mounting bracket. The larger dual-frequency Skimmers typically use a two-piece, plastic mounting bracket.
4 then the chosen location must be in the water at all times. If the transducer is not placed in a smooth flow of water, interference caused by bubbles and turbulence will show on the sonar's display in the form of random lines or dots whenever the boat is moving.
5 Align transducer centerline with hull bottom. However, there are times when you may need to adjust the transducer slightly higher or lower. (The slot s in the mounting brackets allow you to loosen the screws and slide the tr ansducer up or down.
6 The following instructions sometime s vary depending on the mounting bracket that came with your transducer. Single frequency Skimmers come with a one-piece stainless steel bracket, while dual frequency Skimmers come with a two-piece plastic mounting bracket.
7 Add ratchets to bracket and transducer. 2. Aligning the transducer on the transom. A. One-piece bracket: Slide the transducer between the two ratch- ets.
8 B. Two-piece bracket: Assemble the transducer and bracket as shown in the following figure. Temporarily slide the bolt though the transducer assembly but don't tighten the nut at this time. Hold the assembled transducer and bracket against the transom.
9 B. Two-piece bracket: Once you determine the correct position for the ratchets, assemble the transducer as shown in the figure in step 2B. Don't tighten the lock nut at this time. 4. Drilling mounting holes. Hold the transducer and bracket assembly against the transom.
10 Both bracket types: Attach the transducer to the transom. Slide the transducer up or down until it's aligned properly with the bottom of the hull as shown in the preceding and following figures. Tighten the bracket's mounting screws, sealing them with the caulking compound.
11 7. Make a test run to determine the results. If the bottom is lost at high speed, or if noise appears on the display, try sliding the trans- ducer bracket down. This puts the transducer deeper into the water, hopefully below the turbulence ca using the noise.
12 TRANSDUCER ORIENTATION AND FISH ARCHES If you do not get good fish arches on your display, it could be because the transducer is not parallel with th e ground when the boat is at rest in the water or at slow trolling speeds. Transducer angles and their effects on fish arches.
13 transducer installation can be made on hulls with flotation materials (such as plywood, balsa wood or fo am) between layers of fiberglass if the material is removed from the chosen area.
14 cation that shot through the hull th e best and follow the instructions on the following pages for a shoot-thru-hull mounting. Shoot-thru-hull transducer locations for high speed or trolling speed operation.
15 Place the transducer into the epoxy, twisting and turning it to force any air bubbles out from under the transducer face. The face of the transducer should be parallel wi th the hull, with a minimum amount of epoxy between the hull and tr ansducer.
16 X51 or X58DF with external speed sensor. A temperature sensor is built into the transducer. X51 using a transducer without built-in temperature sensor.
17 X51 or X58DF with external combination speed and temperature sensor. Speed Sensor Installation Though only the X58DF comes packed with a speed sensor, both units are capable of displaying speed and distance traveled.
18 Stern view showing good location for mounting sensor on transom. Speed sensor mounting configuration: side view (left) and rear view (right.) If the base of the transom has a ra dius, fill the gap between the tran- som and the sensor with the caulki ng compound.
19 Power connections for the X51 and X58DF sonar unit. If possible, keep the power cable away from other boat wiring, espe- cially the engine's wires. This will provide the best isolation from elec- trical noise. If the cable is not lo ng enough, splice #18 gauge wire onto it.
20 In-dash mounting template for X51 and X58DF sonars, showing dimen- sions. NOTE: The figure above is not printed to scale. A scaled template is available for free download from our web site, www.
21 Front view (left) and side view (right) showing dimensions of X51 and X58DF sonar unit when mounted on gimbal bracket. If you wish, you can fill in the hole around the cables with a good ma- rine caulking compound. (Some mari ne dealers stock cable hole covers to conceal the opening.
22 for your sonar. You can use your X51 or X58DF on your boat or take it to the dock, on a float tube, on an ice fishing trip or use it as a second sonar in a friend's boat. The PPP-10 Portable Power Pack can be used with eight "D" cell alkaline batteries (not included) or an opti onal sealed, rechargeable battery.
23 NOTE: For optimum operation, the portable transducer should be adjusted so that it is parallel to the gro und. For more information on this, see the earlier segment on Transducer Orientation and Fish Arches. Operation KEYBOARD BASICS The unit sounds a tone when you press any key.
24 2. MENU UP (menu up) 3. MENU DOWN (menu down) These keys appears in the manual text as MENU UP or MENU DOWN . (In some units, the keys may appear as MENU FWD or MENU REV , respec- tively.) Most of the time, the inst ructions require you to press either menu key, so the text simply uses the word MENU .
25 All you have to do to leave on e menu and enter another is press MENU re- peatedly. If you ever get lost in the menus, simply press the PWR key. This clears the menus from the screen. Menus change depending on the mode the unit is in. Messages may appear in menu boxes or new menus can appear , depending on previous selections.
26 Chart menu. Chart is running or scrolling normally at left. Chart is stopped at right, and "Stopped" warning message appears. SCREEN DISPLAY MODES or PAGES The X51 has four screen display mo des, or "Pages:" Full Chart page, Split Chart page, Large Digital page and Flasher page.
27 the depth of fish, structure, and othe r targets. The line at the top of the screen represents the surface. The bottom depth (as determined by the digital sonar) shows in the upper left corner. If yo ur s p ee d se n so r is co n- nected, digital displays for speed and temperature will also be shown.
28 DUAL-FREQUENCY SPLIT CHART (X58DF only) This page shows sonar data from th e 50 kHz transducer element on the left side of the screen and data from the 200 kHz transducer on the right side. All other functions and features are the same as the Full Chart page.
29 Lrg DIGITAL (Large Digital) The Large Digital page shows all information in big numbers. The digi- tal depth display is at the top of this screen, followed by the tempera- ture, speed, and distance readings. NOTE: Temperature, speed, and distance require a temperature or speed sensor.
30 RANGE When turned on for the first time , the unit automatically adjusts the depth range according to water cond itions. It always keeps the bottom displayed in the lower portion of the screen. You can over-ride the automatic range control and manually select a range.
31 To set upper and lower limits, press MENU until the R ANGE menu ap- pears. Press DOWN ARROW to select U SE UL/LL , then press MENU UP to open the Upper Limit menu. Use the arrow keys to select the u pper limit. In the example above, we have selected 10 feet.
32 NOTE: Using the Zoom command while in auto Range mode will always enlarge the echoes near the bottom, because auto Range always keeps the bottom displayed in th e lower portion of the screen. When you Zoom in manual Range mode, echoes are enlarged near the middle of the displayed range.
33 SENSITIVITY Sensitivity controls the unit's ability to pick up echoes. If you want to see more detail, try increasing the sensitivity, a little at a time. There are situations when too much clutte r appears on the screen. Decreasing the sensitivity can reduce the clu tter and show the strongest fish ech- oes, if fish are present.
34 you from turning sensitivity down too low to allow automatic bottom tracking. When you change the setting with auto turned on, the unit will continue to track the bottom and ma ke minor adjustments to the sensi- tivity level, with a bias toward the setting you selected.
35 NOTE: If you want to change the sensitiv ity in Manual Mode, first turn off Auto Sensitivity: press MENU until the S ENSITIVITY A UTOMATIC /M ANUAL menu appears. P re s s DOWN ARROW to select M ANUAL , then press PWR to clear the menu. To adjust the sensitiv ity, follow the same steps used for adjusting sensitivity in auto mode above.
36 Press UP ARROW to increase the level or press DOWN ARROW to de- crease it. The percentage of Grayline in use shows in this menu. Echoes scrolling onto the screen will also show the effects of the Grayline change. If you reach the maximum or minimum level, a tone sounds alerting you to the limits.
37 You may see Fish I.D. symbols on the s creen when actually, there are no fish. The reverse is also true — Fish I.D. can actually miss fish that are present. Does that mean Fish I.D. is broken ? No — the feature is simply inter- preting sonar returns in a specific wa y to help take some of the work out of reading the screen.
38 FISHREVEAL When displaying actual sonar returns, the FishReveal feature helps show fish targets hidden by surface clutter, thermoclines, weed beds and other cover with 10 levels of gray tones. Normal operation (with FishReveal turned off) shows the weakest ech- oes as black and the strongest in light gray.
39 At left, standard FishReveal mode. Right, Inverted Fish Reveal mode. CHART SCROLL SPEED and HYPERSCROLL The rate that echoes scroll across th e screen is called the chart scroll speed. The default for this unit is 60 percent; we recommend that you leave the scroll speed set there for virtually all fishing conditions.
40 At right, Scroll Speed menu at default 60 percent setting. At left, Scroll Speed menu, with unit set to HyperScroll mode. If you are running fast, try a HyperScroll setting of 80 to 100 percent. When using HyperScroll, you may al so need to manually decrease the sensitivity for best performance.
41 The ASP noise rejection feature is es pecially useful because it typically lets you operate the boat at all sp eeds without adjusting the sensitivity or other controls. Noise Reject menu. The ASP feature has four setting s — Off, Low, Medium and High.
42 To turn off the fish alarm without turning off fish symbols, press MENU DOWN until F ISH A LARM appears. Press DOWN ARROW to select O FF , then press PWR to clear the menu. Repeat the above steps to turn the alarm back on, but press UP ARROW to select O N before clearing the menu.
43 Press UP ARROW to increase the shallow alarm's depth setting or press DOWN ARROW to decrease it. The number in the shallow alarm’s menu box shows the current shallow alarm setting. When the number reaches the desired setting, press PWR to clear the menu.
44 SYSTEM SETUP To customize the display, press MENU DOWN until the S YSTEM S ETUP menu appears, then press UP ARROW . The display contrast, units of measure, temperature, and system information screens are all under this menu. The Contrast menu appears first.
45 To adjust the contrast, press MENU DOWN until the S YSTEM menu ap- pears, press UP ARROW , and the C ONTRAST menu appears. To decrease screen contrast, press the DOWN ARROW key. Press the UP ARROW key to increase screen contrast. The ba r graph in the Contrast menu box shows a graph of the contrast.
46 TEMPERATURE UNITS OF MEASURE This unit can show the temperature (if a temperature sensor is attached) in degrees Fahrenheit or Celsius. To change the unit of measure, press MENU DOWN until the S YSTEM menu appears. Press UP ARROW , then press MENU until the T EMPERATURE menu appears.
47 RESET DISTANCE LOG You can reset the distance log to zero with this command. Press MENU DOWN until S YSTEM appears, then press UP ARROW . Press MENU until the R ESET L OG menu appears. Press UP ARROW and the log returns to zero. Press PWR to clear the menu.
48 SYSTEM INFO To show the operating software system information, press MENU DOWN until the S YSTEM menu appears, then press UP ARROW . Press MENU DOWN until the S YSTEM I NFO screen appears. Press PWR to clear the screen. System Info screen. SIMULATOR This unit has a built-in simulator th at shows a simulated bottom signal with fish signals.
49 NOTE: If you turn on your unit before a ttaching a transducer, it may enter a demo mode. The words "demo mo de" flash on the bottom of the screen and a sonar chart plays much like the simulator.
50 High boat speed and slow ping speed (caused by the deeper bottom) can reduce the screen refresh rate. This in turn can reduce the amount of detail seen on the sonar chart. Try this command only if you are in deep water, traveling at high speed, and notice a reduction in detail on the sonar chart.
51 The default frequency is 200 kHz, whic h is best for use in shallow water (about 300 feet or less). This freque ncy is the best choice for about 80 percent of the fresh and salt water sport fishing applications. When you get into very deep salt water, 300 to 500 feet or deeper, the 50 kHz fre- quency is the best choice.
52 Menus for changing digital number size. SCALES The depth scale between the upper an d lower limit on the right side of the screen can be turned on or off.
53 Troubleshooting If your unit is not working, or if yo u need technical help, please use the following troubleshooting section befo re contacting the factory customer service department. It may save you the trouble of returning your unit for repair.
54 noise rejection feature. This can cause the unit to eliminate weaker signals such as fish or even structure from the display. 3. The water may be deeper than the sonar's ability to find the bottom. If the sonar can't find the bottom si gnal while it's in the automatic mode, the digital sonar display will flash continuously.
55 NOISE A major cause of sonar problems is electrical noise. This usually ap- pears on the sonar's display as random patterns of dots or lines. In se- vere cases, it can completely cover the screen with black dots, or cause the unit to operate erratically, or not at all.
56 Notes.
57 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRAN CE ELECTRONICS, INC ., the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family or household use.
58 How to Obtain Service… …in the USA: We back your investment in quality pr oducts with quick, expert service and genuine Lowrance parts. If you' re in the United States and you have technical, return or repair qu estions, please contact the Factory Customer Service Department.
Accessory Ordering Information for all countries To order Lowrance GPS accessories such as computer cables or MMC cards, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electr onic equipment or other consumer electronics should be able to assist you with these items.
Visit our web site: Lowrance Pub. 988-0105-951 © Copyright 2002 All Rights Reserved Printed in USA 092402 Lowrance Electronics, Inc..
Een belangrijk punt na aankoop van elk apparaat Lowrance electronic X58DF (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lowrance electronic X58DF heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lowrance electronic X58DF vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lowrance electronic X58DF leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lowrance electronic X58DF krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lowrance electronic X58DF bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lowrance electronic X58DF kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lowrance electronic X58DF . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
