Gebruiksaanwijzing /service van het product RP-1 van de fabrikant Lyngdorf Audio
Ga naar pagina of 40
Owner´s manual RP-1 RoomPerfect™ MENU MENU ENTER ENTER RP-1 Room Processor.
2.
3 T able of Contents Operating V oltage 4 Unpacking the RP-1 4 Serial Number Registration 4 Introduction 5 Accessories 6 Front Panel 7 Display Indicators 8 Rear Panel 8 Remote Control 10 Connecting th.
4 Operating V oltage The RP-1 can be switched between 115V and 230V mains voltage. In 115V mode the RP-1 requires a mains voltage of 100V -120V at 50-60Hz. In 230V mode the RP-1 requires a mains voltage of 220V -240V at 50-60Hz. The mains voltage setting for your RP-1 can be changed on the rear selector .
5 Introduction Congratulations on the purchase of your L yngdorf Audio RP-1 with RoomPerfect™. This ‘Black Box’ expands your existing music system with the most advanced room correction system on the market. It is implemented in such a way that you will always achieve the perfect result.
6 Owner´s manual RP-1 RoomPerfect™ MENU MENU ENTER ENTER RP-1 Room Processor Accessories Y ou should fi nd the following accessories included: Mains cord 8 m (26.
7 Front Panel 1 2 3 4 MENU MENU ENTER ENTER RP-1 Room Processor Controls The buttons/controls on the front panel of the RP-1 can all be operated with a direct press. 1. Mains Switch Powers the RP-1 on/off. 2. Display Display with all information on menu system and status.
8 Display Indicators 1 3 2 1. Menu Alphanumeric Display (2*20 Characters). 2. Standby Indicator Power On is indicated with display showing all information on status. Standby mode is indicated with the Standby Indicator being lit only . 3. RoomPerfect Logo Is illuminated whena RoomPerfect fi lter is engaged.
9 3. Analog Input Balanced/XLR Left/Right Analog input. Never connect balanced and unbalanced Input at the same time. 4. Analog Input Unbalanced/RCA Left/Right Analog input. The default Input setting is “Balanced / XLR”. This can be changed to “Unbalanced / RCA” from the “Input Connection” menu.
10 Remote Control The remote control is used to access the menu system as well as the buttons directly accessible on the front panel. T o control the RP-1 the RCS (Room Correction System) key must be pressed.
11 16. V olume Up/down No function. 17. Up / Down / Left / Right In normal operation mode the Up/Down toggles between Bypass, Focus and Global fi lter and the Left/ Right toggles between Neutral and the available voicings. In menu mode they are used for navigation in the menu system.
12 Connecting the RP-1 The photos used are only meant as visual aids to show the versatility of the RP-1, L yngdorf Audio doesn’t necessarily carry all other products with the described speci- fi cations in the product assortment. Connecting to sources and amplifi ers The RP-1 is very simple to hook up.
13 3. If your integrated amplifi er or preamp has a ‘tape 2’ loop (sometimes called recording loop) or ‘Pre in/out’: Connect the output of the ‘tape 2’ loop / ‘Pre out’ to the input of the RP-1. • • Then connect the output of the RP-1 to the input of the ‘tape 2’ loop / ‘Pre in’.
14 Setup options of Main and Line outputs As described in “Routing” and “Crossover Frequency” there are many ways to utilize the Main and Line out- puts. Here we have described the three most common set-up´s. Please note the products, outputs and cross- over frequencies are chosen randomly in these descriptions.
15 Menu System The Main Display on the front panel of the RP-1 shows all functionality and current status of the RP-1. An overview of the menu tree can be seen in the ‘Menu T ree’ chapter . Navigating the Menu System Pressing the Menu button on the front panel or the remote enters the menu or steps back one level in the menu system.
16 Menu T ree This is an overview of the entire RP-1 menu structure. RP-1 Mai n Menu Dis p l ay D i spl ay T i m e out D i sp . B r i ghtne ss RoomPer fe c t Gui d e d s e tup Adv anc e d opti ons Mea.
17 Introduction to RoomPerfect™ Once the guided set-up has been successfully completed you have the option to listen to music through two listening settings; Focus and Global room correction fi lters. T o toggle between the two fi lters and ‘Bypass’ you simply press the Up/Down buttons on the front panel or remote control.
18 RoomPerfect™ The sub menus accessible in the RoomPerfect™ menu are: Advanced options is only available when Guided set-up has been performed. Guided Setup When you enter the RoomPerfect™ Main Menu for the fi rst time, only the Guided setup is available.
19 Setting the Measurement V olume Level When setting the measurement volume level, it is important that you always judge whether the calibra- tion volume is too loud. The calibration volume should not be so loud that it causes: • uncomfortably loud sounds that are inconvenient to you or your environment, or • damage to your loudspeakers.
20 When the message ‘Calibration ok. Press Enter to continue’ is displayed, the calibration volume has suc- cessfully been set and saved. Focus Measurement When the calibration is OK, press Enter to start the measuring process and ‘Measuring Focus position …’ will be displayed.
21 For an optimal room correction it is very important that the measurements are: 1. performed more than 1 meter (approx. 3 feet) away from the loudspeakers, 2. not performed behind the loudspeaker , and 3. that there is at least 50 cm/1.5 ft between each measurement.
22 Calculation of Focus and Global Filters When RoomPerfect™ calculates the fi lters the display shows the following, ‘Calculating fi lters - Please wait’. The fi lter calculation process can be expected to take anywhere between 5 seconds and a minute de- pending on the specifi c task.
23 Advanced Options This section describes the options in the advanced menu, which is available after Guided Setup has been completed. Here you can change the listening position and add more room measurements, check the RoomKnowledge of your current set-up, and check the RoomCorrection for the different fi lters.
24 ‘Add more room meas.? Y es/No’ will show in the display: • choose Y es to add another room measurement or , • choose No to stop adding more room measurements. If No is chosen the RP-1 is will return to full scale output. ‘Save room measurement(s)? Y es/No’ will hereafter be shown.
25 Display The sub menus accessible in the Display menu are: Display Di spl ay Ti meout D isp . B ri ghtne ss Display T imeout Di spl ay Ti meout Display T imeout Display T imeout set-up is used for enabling/disabling the 10 sec. display ’ switch’off’ feature.
26 Input Sensitivity Input Sensi ti vi ty The Input Sensitivity setting enables you to match the line level output of your pre-amplifi er to the input sensitivity of the L yngdorf Audio RP-1. The normal settings are: Select ‘High’ for input levels <= 2.
27 Line Out Level This adjusts the overall output level in steps of -0.1 db, it can be attenuated to –40 dB in total. Routing Rout ing In Routing it is possible to apply different settings to the Ma.
28 Crossover Frequency Crossover Frequency is only available when Routing has been setup. The Crossover Frequency can be selected anywhere between 40 – 9999Hz. It is very diffi cult to give exact guidelines to setting a suitable crossover frequency , fi lter type and order since this depends on the exact drivers and confi gurations.
29 Delay If you are using a set-up with two main loudspeakers located at an identical distance to the listening position you don’t need to set a delay .
30 Firmware V ersions The Firmware V ersions menu is used to check the current fi rmware version of your RP-1 and the Room- Perfect™ module as well as the RoomPerfect™ serial number . Factory Reset The Factory Reset setting is used to restore all settings, including RoomPerfect, in the RP-1 to the fac- tory settings.
31 T roubleshooting RoomPerfect™ No microphone connected The error message ‘No microphone connected’ is displayed when no microphone is connected to the RP-1. Solution: • Connect the microphone on the back panel. No signal 1. The error message ‘Fault – No signal’ is displayed when the incoming signal is classifi ed as pure noise.
32 T roubleshooting RP-1 Speakers are humming when the RP-1 is turned on Balanced and unbalanced for Main out connections are used at the same time. Solution: • Disconnect the interfering connection. Speakers are humming when the RP-1 is turned on Balanced and unbalanced for Line out connections are used at the same time.
33 Firmware Upgrading The RP-1 fi rmware can be upgraded using the ‘L yngdorf Audio – Serial Load’ software. This is in the PC package available from www .L yngdorf.com. Press the Enter button while powering On to bring the product into upgrade mode.
34 Connectors Mains Connector Mains voltage to the RP-1 is applied via an IEC320 type connector . The supplied cable with safety ground should be used to connect the RP-1 to a mains outlet. Make sure the rear selector is in the correct setting and connect the power input only to an appropiate AC source.
35 T echnical Specifi cations Audio Parameter V alue Note Balanced input connectors 3 pin XLR, gold-plated. Case=Gnd, Pin1=Gnd, Pin2=Hot(+), Pin3=Cold(-) Balanced input impedance 10KOhm AC-coupled. Unbalanced input connectors RCA (phono) jack, gold-plated.
36 T echnical Assistance For latest version of the fi rmware, the newest version of this document and ‘Questions and Answers’, please check the ‘Support’ section on the L yngdorf Audio website.
37 Appendix V oicing Curves For further information on the V oicing setting, please refer to the “V oicing” chapter . Music 1 Music 2 Open Open Air Relaxed Soft 10 Hz 100 Hz 1kHz 10k Hz -6 -4 -2 0.
38.
39.
40 www .lyngdorf.com.
Een belangrijk punt na aankoop van elk apparaat Lyngdorf Audio RP-1 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lyngdorf Audio RP-1 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lyngdorf Audio RP-1 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lyngdorf Audio RP-1 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lyngdorf Audio RP-1 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lyngdorf Audio RP-1 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lyngdorf Audio RP-1 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lyngdorf Audio RP-1 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
