Gebruiksaanwijzing /service van het product Series 5000 Rack Frame van de fabrikant Lynx
Ga naar pagina of 39
Series 5000 © LYNX Tech nik AG Brunnenweg 3 64331 Weiterstadt Germ any www.l ynx-techn ik.com Reference Manual R FR 5010 / R FR 5011 Series 5000 Rack Frame CardModul e Ver 2.
Reference Manual R FR 5010 Versio n1.4 Page 2 Infor matio n in this d ocum ent is subjec t to chan ge wit hout notice. No part of thi s docu ment may be reproduced or tra ns mit te d in an y fo rm o r by any mean s, ele ctr on ic or mechani cal for any purpose, wi thout express written pe rmission of LYNX Techni k AG.
Reference Manual R FR 5010 Versio n1.4 Page 3 WARNING Electrical supplies in excess of 50 ( fifty) volts peak value are potentially hazardous or lethal. AC supplies b etween 100 and 250 peak volts exist w ithin the rack fr ame chassis when connected to AC pow er.
Reference Manual R FR 5010 Versio n1.4 Page 4 WARNUNG ! Wenn das Gerät an das Wechselstrom netz angeschlossen ist, treten innerhalb des Gerätes Wechselspannungen zwischen 100 und 250 V auf, di e potentiell gefährlich oder tödlich sein können. Desh alb darf Reparatur und Instandhaltung nur von qualifiziertem Personal durchgeführt werden.
Reference Manual R FR 5010 Versio n1.4 Page 5 This Page is intentionally left blank.
Reference Manual R FR 5010 Versio n1.4 Page 6 Warranty LYNX Technik AG warrants that the product will be free fro m defects in materials an d workma nship for a period of two (2) years fro m the dat e of shipm ent.
Reference Manual R FR 5010 Versio n1.4 Page 7 Regulatory information Europe Declar ation of Co nformit y USA FCC 47 Part 15 This device compli es with part 15 of the FCC Rules.
Reference Manual R FR 5010 Versio n1.4 Page 8 Contents Warranty ........... .................... ................... ................. ................ 6 Regulatory information .... .................... ................... ................ 7 Europe ..
Reference Manual R FR 5010 Versio n1.4 Page 9 Electrical Installation. ... ............................................. ............ 31 Install ation In structions . ............................................. ............ 32 Installat ions-Anweisun g .
Reference Manual R FR 5010 Versio n1.4 Page 10 Getting Started Packaging The shipping carton and packaging m a terials provide protecti o n for the module during transit. Please retain the ship ping cartons in case subseque nt shipping of the product becomes necessary.
Reference Manual R FR 5010 Versio n1.4 Page 11 board multifunction LED has various s t ates to indicate dif ferent alarm condit ions and a separate GPO alarm output is provid ed for connection to an external monitoring system.
Reference Manual R FR 5010 Versio n1.4 Page 12 Rack Layout Figure 2 and 3 shows explo ded view s of th e R FR 5010 / R FR 5011 . The Front cover is removed and not shown.
Reference Manual R FR 5010 Versio n1.4 Page 13 Figure 3 – Exploded r ack view For clarity (to show rack construction) power supplies, rear termination panel and conne ction panels for the modules have been omitted. Caut i on : Do not obstruct ventilation holes on top and bottom si des of rack.
Reference Manual R FR 5010 Versio n1.4 Page 14 Power Supply The R FR 5010 / R FR 5011 includes the primary power supply. A secon d identical p ower supply can be added for redundancy. The Power su pply is a sophisticate d design designed for critical applications and includes po wer filtering and integral micro processor .
Reference Manual R FR 5010 Versio n1.4 Page 15 Power Supply seen from Front Sec uri n g Scr ew Integral Fan Handle for rem oval LED A l arm indicator Figure 4: Power Suppl y.
Reference Manual R FR 5010 Versio n1.4 Page 16 Rear Termination Pan el The R FR 5010/ R FR 5011 ha s an integral termination panel on the rear of the rack for the connection of power and various other connections for expansion and interfacing.
Reference Manual R FR 5010 Versio n1.4 Page 17 ! ! A stud is provi d ed on the termination panel for the connectio n of an ext ernal ground . (Figure 5) Note: the chassis is permanently grounde d via the AC connections.
Reference Manual R FR 5010 Versio n1.4 Page 18 Alarm Function This function requires the controller option. The user can assig n triggers for the preferre d Major / Minor and No Alarm conditi ons using the co ntroller and supplied sof tware. The alarm connecto r provides GPO co ntacts for 2 alarm levels and a GPI inpu t for future use.
Reference Manual R FR 5010 Versio n1.4 Page 19 Extend Connection Bus Extension . Thi s connect ion is used to inte rface racks together when using the optional LYNX control system. This is a simple (and inexpe nsive) way to extend the reach of the host RCT 5020 controller into several mo re racks fitted with RCT 5010 bus expanders.
Reference Manual R FR 5010 Versio n1.4 Page 20 Control Connectio n An external Control Interf ace is provided on the rear termination panel. When an R CT 5020 Rack Controller (or R CT 5030 Master Controller) is fitted to the rack this port ca n be used for two primary functions: 1.
Reference Manual R FR 5010 Versio n1.4 Page 21 LAN Connection This is a standard RJ4 8 connection and i s used to provide stand ard TCP/IP n etwork cont rol connectivity into a contr ol system. To be operational this port requires the R CT 5030 Master Controller is fi tted to the rack.
Reference Manual R FR 5010 Versio n1.4 Page 22 Alarm/LED Status Indicators There are a number of status / alarm ind icators visible throu gh the front panel of the R FR 5010 Rack frame.
Reference Manual R FR 5010 Versio n1.4 Page 23 Power Supply LED Indicators The Table below shows the erro r conditions for the LED on the power supply units.
Reference Manual R FR 5010 Versio n1.4 Page 24 Rack Configuration Assembly If starting with an empty R FR 5010 / R FR 5011 rack frame please follo w the following steps for correct installation of the.
Reference Manual R FR 5010 Versio n1.4 Page 25 Redunda nt Power Supply The basic RFR 5010 / R FR 5011 is supplied with the primary powe r supply installed.
Reference Manual R FR 5010 Versio n1.4 Page 26 D AA3320 W IN L IN R OUT L1 OUT R1 OUT L2 OUT R2 OUT L3 OUT L4 OUT R3 OUT R4 DUAL AUDIO ANALOG DIST AMP D AA3320 D IN OUT DUAL ANALOG AUDIO DISTRIBUTION .
Reference Manual R FR 5010 Versio n1.4 Page 27 Hot Swapping Power Supplies The Series 5000 Card Modules and Power Supplies are fully hot swappable in the event of a fault or failure.
Reference Manual R FR 5010 Versio n1.4 Page 28 Rack Installation If you have an empty R FR 5010 rack frame we recommend you assemble the connectio n plates and modules as well as any options such as the redundant power supply and controller before mounting the Rack Fram e into a 19” inch rack.
Reference Manual R FR 5010 Versio n1.4 Page 29 5101 rack frame may (due to the small airf low gap) restri ct the flow of ai r to this piece of equipmen t. Also do not place equi pment or objects on top of the R FR 5010 rack frame th at could restrict airflow from the top of the rack.
Reference Manual R FR 5010 Versio n1.4 Page 30 Fig.11: Sub D 9 Connector on Front Cover of R FR 5011 Fig.12: Sub D 9 Connector on right si de of R FR 5011.
Reference Manual R FR 5010 Versio n1.4 Page 31 ! ! Electrical Installation. Electrical power is connected to the R FR 5010 / R FR 5011 ch assis via the two I EC power connectors located on the termination panel on the rear of the rack. Th ere is n o power swit ch provided .
Reference Manual R FR 5010 Versio n1.4 Page 32 Installation Instructions The rack frame chassis R FR 5010 / R FR 5011 is intende d for operation in broadcast environments. The operation in excessive d ust and moisture o r extreme temperature requi res special provisions like • dust filters • air conditioning • avoi dance of conden sed wate r.
Reference Manual R FR 5010 Versio n1.4 Page 33 Installa tions-Anweisung Das Ger ät R FR 501 0 / R FR 5011 ist fü r Anwendungen in Fernsehstudios vorgesehen.
Reference Manual R FR 5010 Versio n1.4 Page 34 Settings and Control There are no specific setting and control parameters fo r the card rack. This is pro vided via controller o ption (i f fitted) an d the individ ual CardModule assemblies.
Reference Manual R FR 5010 Versio n1.4 Page 35 Specifications (R FR 5010 / R FR 5011) Mechanical Size 2 RU high x 32.5 cm deep including connectors and front cover.
Reference Manual R FR 5010 Versio n1.4 Page 36 Available Options Below is a list of available options for the R FR 50 10 rack frame. Please refer to product brochures or our web site for more detailed inform ation.
Reference Manual R FR 5010 Versio n1.4 Page 37 Parts List There are no user serviceable electron ic assemblies within the R FR 501 0 module. The parts list below shows high-l evel sub assemblies used in this rack, which can be ordered separate ly for maintena nce purposes.
Reference Manual R FR 5010 Versio n1.4 Page 38 Contact Information Please contact your local d i stributor; this is your local a nd faste st method f o r ob taining su pport and sales information. Lynx Technik can be cont acted directly using the information below.
Reference Manual R FR 5010 Versio n1.4 Page 39 Notes.
Een belangrijk punt na aankoop van elk apparaat Lynx Series 5000 Rack Frame (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lynx Series 5000 Rack Frame heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lynx Series 5000 Rack Frame vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lynx Series 5000 Rack Frame leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lynx Series 5000 Rack Frame krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lynx Series 5000 Rack Frame bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lynx Series 5000 Rack Frame kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lynx Series 5000 Rack Frame . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.