Gebruiksaanwijzing /service van het product ONYX 820i van de fabrikant Mackie
Ga naar pagina of 42
OWNER’S MANUAL P remium 8-Channel Analog Mix er with P erkins EQ and F ireWire MUTE SOLO 48V MUTE SOLO 48V MUTE SOLO 48V LINE MUTE SOLO MUTE SOLO TAP E PAN 2 1 MID FREQ MID FREQ BAL/UNBAL BAL/UNBAL .
2 Onyx 820i 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with a dr y cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
Owner ' s Manual 3 Part No. SW0718 Rev . D 02/2010 ©2010 LOUD T echnologies Inc. All Rights Reserved. Loosely based on a dream sequence in which the technical writer is given keys to a sports car of his choice, unlimited gas, and closed roads. The dream suddenly ends and reality kicks in.
4 Onyx 820i Introduction Thank you for choosing a Mackie Onyx 820i professional compact mixer . The Onyx i series of mixers offer built-in Fir eWir e, along with the newest features and latest technologies for live sound r einforcement and analog or digital studio r ecording, all in a durable, road-worthy package.
Owner ' s Manual 5 Ho w T o Use This Manual The fi rst pages after the table of contents ar e the hookup diagrams. These show typical setups for fun times with your mixer .
6 Onyx 820i Contents IMPOR T ANT SAFETY INSTRUCTIONS ........................ 2 QUICK ST ART .......................................................... 3 INTRODUCTION ...................................................... 4 YOU ARE HERE ..............
Owner ' s Manual 7 Hookup Diagrams 1-2 Man Coffeehouse Gig MUTE SOLO 48V MUTE SOLO 48V MUTE SOLO 48V LINE MUTE SOLO MUTE SOLO TA P E PAN 2 1 MID FREQ MID FREQ BAL/UNBAL BAL/UNBAL A LT 3- 4 A LT 3.
8 Onyx 820i Home Studio System: Straight to stereo MUTE SOLO 48V MUTE SOLO 48V MUTE SOLO 48V LINE MUTE SOLO MUTE SOLO TA P E PAN 2 1 MID FREQ MID FREQ BAL/UNBAL BAL/UNBAL AL T 3-4 AL T 3- 4 AL T 3-4 A.
Owner ' s Manual 9 Home Studio System: Recording each channel MUTE SOLO 48V MUTE SOLO 48V MUTE SOLO 48V LINE MUTE SOLO MUTE SOLO TA P E PAN 2 1 MID FREQ MID FREQ BAL/UNBAL BAL/UNBAL ALT 3- 4 ALT .
10 Onyx 820i Club System MUTE SOLO 48V MUTE SOLO 48V MUTE SOLO 48V LINE MUTE SOLO MUTE SOLO TA P E PAN 2 1 MID FREQ MID FREQ BAL/UNBAL BAL/UNBAL AL T 3-4 ALT 3- 4 ALT 3-4 A L T 3-4 ALT 3- 4 LOW MID 400Hz O N Y X M I C P R E HIGH 12kHz LOW 80Hz EQ INSERT INSERT O N Y X M I C P R E HIGH 12kHz LOW 80Hz EQ O N Y X M I C P R E HIGH 12kHz HIGH MID 2.
Owner ' s Manual 11 P ost-Production System This diagram shows a voice-over microphone connected to channel 1 mic input, a video deck's audio output connected to channels 3/4, with its audio inputs receiving the main mix from the 1/4" outputs.
12 Onyx 820i Onyx 820i Features Rear Panel 1. POWER CONNECTION This is a standard 3-prong IEC power connector . Connect the detachable linecord (included in the box with your mixer) to the power r eceptacle, and plug the other end of the linecord into an AC outlet.
Owner ' s Manual 13 These same two channels from the computer can also be chosen as inputs to channels 7 and 8, allowing you to adjust the gain, EQ, level, and pan, as well as to solo, and add to aux send 1 and 2. This is routed using the FW/line input selector [22] on channels 7 and 8.
14 Onyx 820i PHANTOM POWER Most modern professional condenser mics r equire 48V phantom power , which lets the mixer send low-curr ent DC voltage to the mic’s electronics through the same wir es that carry audio. (Semi-pro condenser mics often have batteries to accomplish the same thing.
Owner ' s Manual 15 Insert jacks can be used as channel dir ect outputs; post-gain, and pr e-EQ. See the connector section on page 30 (fi gur e G) showing thr ee ways to use insert cables.
16 Onyx 820i 15. T APE INPUTS These ster eo unbalanced RCA inputs allow you to play a tape, CD player , iPod ® dock, or other line-level source. The tape in jacks accept an unbalanced signal using standard hi-fi hookup cables. Push in the tape button [39] to route the tape input to the control room and phones outputs [6, 17].
Owner ' s Manual 17 Channel Controls The vertical channel strips look very similar , and have only a few differ ences between them. Each channel works independently , and just controls the signals plugged into the inputs dir ectly above it.
18 Onyx 820i Plugging a guitar into a lower -impedance line-level input can r esult in the loss of high fr equencies, causing an unnatural and dull sound. Normally , you must use a direct box between a guitar and a mixer’ s input, which serves to convert the impedance of the guitar from high to low .
Owner ' s Manual 19 This 20 dB of attenuation can be very handy when you ar e inserting a hot signal, or when you want to add EQ gain, or both. W ithout this “virtual pad,” there is mor e chance of channel clipping. 24. SEND FIREWIRE PRE/POST Each channel of the mixer can send a Fir eWir e output to your computer or DA W .
20 Onyx 820i 26. MID EQ FREQUENCY (Ch. 1 and 2) This knob sets the center fr equency of the mid EQ level control [27]. This is sweepable from 100 Hz to 8 kHz.
Owner ' s Manual 21 32. AUX SEND 1 and 2 These controls allow you to set up two independent mixes, typically for running stage monitors or external effects processors. The controls ar e off when turned fully down, deliver unity gain at the center , and can provide up to 15 dB of gain turned fully up.
22 Onyx 820i 35. –20 and OL LEDs These LEDs indicate the channel’ s signal level after the gain and EQ controls, but just befor e the channel’s level. So even if the level is turned down, you can see if a signal is pr esent, or if the channel is being overloaded.
Owner ' s Manual 23 the Fir eWir e connection from your computer . Alt 3-4 is the additional ster eo mix bus formed when any channel is muted with the mute/alt 3-4 switch [34]. Selections made her e deliver stereo signals to the control room, phones, and meters.
24 Onyx 820i 42. PHONES Knob This controls the volume at the phones output, from off to maximum gain. W ARNING: The headphone amp is loud, and can cause permanent hearing damage.
Owner ' s Manual 25 Aux Master This section includes the aux sends and the aux r eturns. Aux sends tap signals off the channels, via the aux knobs [32], mix these signals from each channel together , then sends them out the aux send jacks [12] and Fir eWir e outputs 7 and 8.
26 Onyx 820i 50. POWER LED This gr een LED will turn on when the mixer is turned on, as a r eminder of how on it really is. If it is not on, then it is off, and the mixer becomes a rather nice weight for keeping your morning newspaper from blowing away in the wind.
Owner ' s Manual 27 The aux 1-2 switch routes the talkback signal to the aux send 1 and 2 outputs [12]. Use this to communicate with the musicians through their stage monitors when you ar e setting up a live performance.
28 Onyx 820i Appendix A: Ser vice Information If you think your mixer has a problem, please check out the following troubleshooting tips and do your best to confi rm the problem. Visit the Support section of our website (www .mackie.com) where you will fi nd lots of useful information such as F AQs, documentation and any updated PC drivers etc.
Owner ' s Manual 29 “XLR” Connectors Mackie mixers use 3-pin female “XLR” connectors on all microphone inputs, with pin 1 wir ed to the grounded (earthed) shield, pin 2 wir ed to the “h.
30 Onyx 820i TRS Send/Receive Insert Jacks Mackie’ s single-jack inserts are the thr ee- conductor , TRS 1⁄4" phone type. They ar e unbalanced, but have both the mixer output (send) and the mixer input (r eturn) signals in one connector . See Figure F .
Owner ' s Manual 31 Appendix C: T echnical Information Specifi cations Noise Char acteristics: Equivalent Input Noise (EIN), mic input at insert, 150 Ω source impedance, 20 to 20 kHz: 60 dB (max) gain: -127 dBu 40 dB gain: -126.
32 Onyx 820i 14.2 in / 361 mm 9.0 in/ 229 mm 3.7 in/ 94 mm WEIGHT 10.0 lb 4.5 kg 3.8 in / 96 mm 1.6 in / 40.6 mm MUTE SOLO 48V MUTE SOLO 48V MUTE SOLO 48V LINE MUTE SOLO MUTE SOLO 19.0 in/ 482.6 mm (with optional rack ears) MUTE SOLO 48V MUTE SOLO 48V MUTE SOLO 48V LINE MUTE SOLO MUTE SOLO 13.
Owner ' s Manual 33 Block Diagram solo logic Contro l Room level Main level Aux Retu rn 2 L R Insert HPF Level Pan Solo Aux Sends Level Tape L R L/3 R/4 Aux 1 out Aux 2 out Aux 1 level Phones Con.
34 Onyx 820i The optional Rack Ear Kit allows the Onyx 820i mixer to be mounted in a standard 19” rack. It will be out of harm’ s way and the band may continue tearin’ it up without fearing any consequences. The mixer takes up nine rack spaces. Be sur e to allow for an extra space or two above to make connections.
Owner ' s Manual 35 Appendix E: FireWire The mixer comes with a CD containing the PC driver softwar e needed to use your mixer's internal FireW ire interface with W indows XP or Windows Vista. Mac OS X contains built-in drivers, so no softwar e installation is r equired.
36 Onyx 820i 6. Select "Install," and the driver softwar e will be installed. 7. The following message confi rms that the driver softwar e has been successfully installed.
Owner ' s Manual 37 7. Select the “Next” command and the driver softwar e will begin installing. 8. When W indows pr esents you with a warning about the softwar e not having passed Windows testing, select “Continue Anyway .” 9. Repeat steps 3-8 to allow a second driver to be installed.
38 Onyx 820i USING THE ONYX 820i WITH A MAC The Onyx 820i works with Mac OS 10.4.11 and higher . This OS includes the Apple Fir eWir e 2.0 driver . The Onyx 820i will only work with the 2.0 driver , so if you have an OS befor e 10.4.11, you will need to check your system for updates from the nice folks at Apple.
Owner ' s Manual 39 Appendix F: Modifi cations The following modifi cations can be carried out on the Onyx 820i by an authorized service center . Authorized service centers may be found online at: www .mackie.com/scripts/service_centers/search.
40 Onyx 820i MUTE SOLO 48V MUTE SOLO 48V MUTE SOLO 48V LINE MUTE SOLO MUTE SOLO TAP E PAN 2 1 MID FREQ MID FREQ BAL/UNBAL BAL/UNBAL A L T 3- 4 A L T 3- 4 A L T 3-4 A L T 3- 4 A L T 3-4 LOW MID 400Hz O N Y X M I C P R E HIGH 12kHz LOW 80Hz EQ INSERT INSERT O N Y X M I C P R E HIGH 12kHz LOW 80Hz EQ O N Y X M I C P R E HIGH 12kHz HIGH MID 2.
Owner ' s Manual 41 Onyx 820i Limited W arranty Please keep your sales receipt in a safe place. This Limited Product W arranty (“Product W arranty”) is provided by LOUD T echnologies Inc. (“LOUD”) and is applicable to products purchased in the United States or Canada through a LOUD-authorized reseller or dealer .
16220 W ood-Red Road NE • W oodinville, W A 98072 • USA United States and Canada: 800.898.3211 Europe, Asia, Centr al and South America: 425.487 .4333 Middle East and Africa: 31.20.654.4000 F ax: 425.487 .4337 • www .mackie.com E -mail: sales@mackie.
Een belangrijk punt na aankoop van elk apparaat Mackie ONYX 820i (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Mackie ONYX 820i heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Mackie ONYX 820i vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Mackie ONYX 820i leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Mackie ONYX 820i krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Mackie ONYX 820i bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Mackie ONYX 820i kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Mackie ONYX 820i . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
