Gebruiksaanwijzing /service van het product X9 van de fabrikant Magnadyne
Ga naar pagina of 28
Installation Manual Model: X9 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.
T able of Contents Installer Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Component Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield Receiver/Antenna • The combination windshield receiver/antenna mounts on the windshield (inside). • We suggest you mount it on the lower left-hand side of the windshield. Warning! Do not mount in such a manner that it obstructs the driver’s view.
HC8 8-Pin Accessory Harness Violet / White T ach Input Green (-) Common Door Pin Input Violet (+) Common Door Pin Input Blue (-) Hood/T runk Alarm Pin Input Gray (-) Remote Start Hood Pin Safety Input.
5 Harness Quick Reference (continued) HC6 6-Pin Accessory Harness Pink (-) Ignition #3 Output Orange (-) Ground When Armed Output Violet/Black (-) Programmable Channel #4 Output Red / White (-) Channe.
HC1: White 6-Pin High Current Remote Starter Harness (continued) Remove the two 20A fuses prior to connecting these wires and do not replace them until the harness has been plugged into the control module. These wires are the source of current for all the circuits the relay harness will energize.
7 Wiring (continued) By default, the Brown wire is the positive (+) output connection for the siren. Current capacity is 2 amps. Make connection to the (+) red wire from the siren. Connect the (-) black wire coming from the siren to a good chassis ground.
Wiring (continued) 8 HC3: Black 3-Pin Door Lock Harness (continued) 5 Wire Ground at Rest Door Locking Systems 87 87A 85 86 30 87 87A 85 86 30 To +12 Volts (Battery +) To Power Lock Switch To Power Lo.
Wiring (continued) 9 Unlock Driver's Door First for 3-Wire Negative Door Lock Systems 87 87A 85 86 30 Unlock Wire Passenger's Door Lock Unlock To +12V or Ground To +12V or Ground Driver&apos.
10 Unlock Driver's Door First Wiring for 3-Wire Positive Door Lock System 87 87A 85 86 30 87 87A 85 86 30 To +12 Volts (Battery +) To Power Door Lock Switch Lock/ Unlock Wires Lock Unlock 87 87A .
The Black/White wire is a safety input wire. The remote start unit will not activate unless this wire is grounded. When this wire is disconnected from ground, the remote start system is disabled. 1. The primary connection point for the Black/White wire is at the Neutral Safety Switch located on/at the transmission shifting lever.
12 Brown Wire: Positive Safety Shut Down Input This wire provides instant shutdown for the remote start, when it receives +12 volts. If the brake lights switch in the vehicle switches +12 volts to the brake light circuit, connect this wire to the output side of the brake switch.
13 Wiring (continued) HC6 White 6-Pin Connector Some vehicles may require a 3rd ignition connection in order to start the vehicle engine. The Pink wire provides a 200mA (-) ground output that becomes active during engine cranking (default Setting).
This wire will provide a 1 second pulse ground when Channel 3 is activated. The current capacity of this wire is 200mA. This feature allows you to remote control trunk release or other electric device.
This wire will become grounded when the alarm is in a armed state. This wire can be connected to an optional starter / ignition disable relay - ECU disable relay, fuel pump disable relay or it can be used to activate other functions of the vehicle such as window roll-up.
16 P4 Sensor 2-Stage Sensor: Allows easy connection with quick disconnect ability for other optional devices. 1. Red: +12 Volt Constant Input 2. Black: Main Sensor Ground 3.
17 SAVE 4 4 SAVE 4 4 Examine the 3 different feature charts enclosed and decide which feature will get changed. Circling the feature to be changed will make the programming process much easier to perform. Before 15 seconds has passed, push and release the valet switch 2 times holding the button down on the 2nd press.
18 One Chirp Two Chirps Three Chirps Four Chirps Button One LED Pulse Two LED Pulses Three LED Pulses Four LED Pulses (Default Setting) Remote Feature Programming Press the transmitter buttons as illustrated to adjust the features required.
19 One Chirp Two Chirps Three Chirps Four Chirps Button One LED Pulse Two LED Pulses Three LED Pulses Four LED Pulses (Default Setting) Ignition Controlled Door Lock Only Ignition Controlled Door Unlo.
20 ON OFF 3X 5X + 1X (Hold) With the ignition switch in the OFF position, Turn the ignition switch On - Off - On - Off - On - Off Turn On the Ignition 3 long chirps and 3 flashes of the parking lights will confirm exit of the programming mode.
21 Alarm Feature Programming (Group 3) (continued) Before 15 seconds has passed, push and release the valet switch 8 times holding the button down on the 8th press. Wait until four (4) short chirps/beeps + one (1) long chirp/beep is heard. Release the button.
22 10 Minute Run Time 20 Minute Run Time 30 Minute Run Time 5 Minute Run Time Factory Alarm Disarm when trunk release (CH#3) is activated Without this Feature Step 3 (continued) One Chirp Two Chirps T.
23 Engine Crank Detection Programming Explanations Use the transmitter buttons as illustrated to adjust the features required. Keep re-pressing the transmitter button that relates to the feature you want to adjust until the correct amount of chirp/beeps is heard.
24 Press Buttons Chirp/ LED Flash Checking Type Follow Programming and Test Procedure 1 Voltage Type A. Press two times to start the engine. Allow engine to run for more than 10 seconds. B. If engine starts without cranking too long or too short and runs for more than 10 seconds, press to exit programming mode (3 chirps confirm exit).
25 The unit has the ability to report the cause of the last shutdown of the remote start system. 1. Turn the ignition switch to “On” position. 2. Press the ( ) button on the transmitter 3.
26 In this test mode, the installer can save time adjusting the optional sensor sensitivity without using the traditional arming/disarming procedures to adjust the sensor. With the ignition switch in the OFF position, turn the ignition switch On - Off - On - Off - On - Off.
27 Turn the ignition switch from the OFF position to the ON position 3 times leaving it in the Off position the third time. ON ON 3X Step 1 Before 15 seconds has passed, push and release the valet switch 12 times. Holding on the 12th press. You will hear 6 short beeps.
HC1 White 6-Pin P2 Blue 2-Pin P6 Blue 4-Pin HC2 White 5-Pin HC3 Black 2-Pin HC8 Black 8-Pin HC6 White 6-Pin P4 White 4-Pin P1 White 2-Pin P7 Brown 4-Pin Data Port Wiring Diagram X9-IM 7-24-08 Rev.
Een belangrijk punt na aankoop van elk apparaat Magnadyne X9 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Magnadyne X9 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Magnadyne X9 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Magnadyne X9 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Magnadyne X9 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Magnadyne X9 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Magnadyne X9 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Magnadyne X9 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
