Gebruiksaanwijzing /service van het product 4304T van de fabrikant Makita
Ga naar pagina of 19
Jig Saw Model 4304T 4305T MODEL 4304T MODEL 4305T Variable Speed Variable Speed Length Max. cutting capacities Strokes Overall Net of stroke Wood Mild Steel Aluminum per minute length weight 26" 135" 10" 249 mm 19-314") 2.4 kg (1") (5-5/16"1 13/8"1 (%?$'I 500 - 3'000 287 mm (5.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool.
Installing or removing the saw blade CAUTION: .Always be sure that the tool is switched off and unplugged before installing or removing the blade. .Always clean off the blade and blade holder before installing the blade.
For 4305T 1. Press the button to raise the blade installing knob. 2. Rotate the blade installing knob in the 0 direction and the clamp on the blade holder will open. Open the clamp a little more than the thickness of the blade to be installed. 3. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go.
Switch action For 4304T CAUTION : Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. For 4304T To start the tool, simply pull the trigger. Release the trigger to stop.
Refer to the table at right tO Select the pro- Workpiece to be cut However, the appropriate speed may differ Mild Steel per speed for the workpiece to be cut. with the type or thickness of the work- piece. In general, higher speeds will allow Stainless Steel you to cut workpieces faster but the Aluminum service life of the blade will be reduced.
Flush cutting I Loosen the base securing lever and slide the base all the way back. Then tighten the base securing lever to secure the base. cutouts Cutouts can be made with either of two methods A or B.
Finishing edges I To trim edges or make slight dimensional adjustments, run the blade lightly along the cut edges. Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause significant blade wear. The underside of the workpiece can be greased instead of using a coolant.
Guide rule (rip fence; optional accessory) When cutting widths of under 150 mm (5-29/32") repeatedly, use of the guide rule will assure fast, clean, straight cuts. To install it, loosen the bolt on the front of the base. Slip in the guide rule and secure the bolt.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning the clamp on the blade holder If chips or foreign matter get into the clamp on the blade holder, clean out the clamp after removing it from the blade holder.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
9 Jia saw blade No. 58 Aoolication 4 - 60 mm thick 15/32" - 2-318") 4 - 60 mm thick 15/32" - 2-3/8") s Blade type Wood and olvwood I Plastics No. 8-17 Aluminum I Mild steel I Feature s 5 - 60 mm thick 5 - 60 mm thick 113/64' - 2-3/8"1 s 113/64" - 2-3/8"1 No.
JIG SAW Model 4304T Note: The switch, noise suppressor and other part configurations may differ from country to country. 15.
ITEM NO. NO. USED MACHINE ~ 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1.
JIG SAW Model 4305T Note: The switch, noise suppressor and other part configurations may differ from country to country. 17.
45 46 47 48 49 50 51 Head Cover Set IWith Item 26) Gear Shaft Flat Washer 8 Needle Bearing 810 Helical Gear 51 Needle Bearing 810 Flat Washer 26 Push Plate Balance Plate Balance Plate Flat Washer 26 C.
i -. . . . . . . . . . MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Een belangrijk punt na aankoop van elk apparaat Makita 4304T (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita 4304T heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita 4304T vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita 4304T leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita 4304T krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita 4304T bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita 4304T kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita 4304T . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
