Gebruiksaanwijzing /service van het product HK1820 van de fabrikant Makita
Ga naar pagina of 17
PR ODUCT P 1/17 T ECHNICAL INFORMA TION Dimensions: mm (") W idth (W) Height (H) Length (L) 351 (13-3/4) 102 (4) 203 (8) L H W Continuous Rating (W) V oltage (V) Cycle (Hz) Input Output Max. Output (W) 110 120 220 230 240 5.3 5.0 2.6 2.5 2.4 50/60 50/60 50/60 50/60 50/60 550 --- 550 550 550 260 260 260 260 260 390 390 390 390 390 Models No.
P 2 /1 7 [2] LUBRICATION Apply the following lubricants to protect parts and product from unusual abrasion: *Makita grease N.No.1 to the portions designated with black triangle *Makita grease R.No.00 to the portions designated with gray triangle *Makita grease N.
Motor housing P 3 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -1. Chuck Section R epair DISASSEMBLY DISASSEMBL Y M5x20 Pan head screw (2 pcs) Handle section Cap 38 Do the reverse of the disassembling steps. 2) Remove Cap 38 with slotted screwdriver. 4) Remove Chuck cover and Compression spring 42.
Remove Barrel cover support and Barrel cover. P 4 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -2. Barrel, Tool Holder, Cylinder Section R epair DISASSEMBLY 1) Disassemble the Chuck section as described in Figs. 2 , 3 . 2) Disassemble Tool holder, Ring 25 and Cylinder section from Barrel as described in Figs.
P 5 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -2. Barrel, Tool Holder, Cylinder Section R epair DISASSEMBLY Ring 39 1. Pull out Striker from Cylinder section. 2. Remove ring 25, Urethane ring 26 and Ring spring 37 from Cylinder. 3. By removing Ring 39, you can see Pin 6 (3 pcs) that join Tool holder with Cylinder.
P 6 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -2. Barrel, Tool Holder, Cylinder Section R epair ASSEMBLY Fig. 9 Do the reverse of the disassembling steps. Note: Rubber ring 13 is directional when assembled to Impact bolt. Be sure to assemble as illustrated to left in Fig.
P 7 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -4. Motor Section R epair 1) Disassemble Handle section as illustrated in Fig. 2 2) Separate the contact of Carbon brushes from Commutator as described in Fig. 11 . 3) Disassemble Crank housing complete from Motor housing as illustrated in Fig.
P 8 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -4. Motor Section R epair 5) Remov e Crank section from Crank housing complete by tapping Crank housing complete with plastic hammer . ( Fig. 14 ) 6) Remov e Armature from crank housing complete using 1R023, 1R225 and arbor press as described in Fig.
P 9 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -5. Gear (Crank) Section R epair DISASSEMBL Y Fig. 16 ASSEMBL Y Do the rev erse of the disassembling steps. Note: Make sure that O Ring 39 is mounted to Bearing box of Crank section before assembling Crank section to Crank housing complete.
P 1 0 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -6. Handle Section R epair DISASSEMBL Y M5x20 Pan head scre w (2 pcs) 5x25 T apping scre w (2 pcs) Handle section Handle section consists of the follo wing main parts: Handle base, Handle, Handle cover And it can be disassembled as illustrated in Figs.
P 1 1 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -7. Recommended F astening T orque of Scr ews and Bolts R epair T ighten the bolt to the recommended torque described in Fig. 21 . Fig. 21 Fig. 22 [4] MAINTENANCE PR OGRAM When replacing carbon brush, it is recommended to do the follo wing maintenance at the same time for longer service life of the machine.
P 1 2 /1 7 C ircuit diagram White Red Orange Blue Brown Color index of lead wires' sheath Black Clear Fig. D-1A Connector housing A Polyolefin tube (Protecti ve tube) Connector housing B Switch Connector Power supply cord Controller High V oltage Areas wher e Radio Interference Suppression Is Requir ed Fig.
W iring diagram P 1 3 /1 7 Handle base, viewed from Controller side Handle Through hole for passing Lead wires from Controller and Connector housing to the opposite side Handle cov er Handle, vie wed from Handle cover side Handle base Controller Be careful not to pinch the Lead wires with the ribs.
W iring diagram P 1 4 /1 7 Fig. D-4A Fig. D-5A Handle base, vie wed from Controller side Handle base, viewed from Handle side Handle, viewed from Handle co ver side red blue Lead wires cov ered with P.
W iring diagram P 1 5 /1 7 Fig. D-4B Fig. D-5B [2] Wiring in Handle Base and Handle Low V oltage Areas wher e Radio Interference Suppr ession Is Required The Lead wires to Connector housing A must be tight between Controller and Lead wire holder .
W iring diagram P 1 6 /1 7 Fig. D-4C Fig. D-5C [2] Wiring in Handle Base and Handle Other Areas where Radio Interfer ence Suppression Is Not Requir ed Put the slack portion of Lead wires in this space. Route all of the Lead wires to Switch through between the boss and the rib .
W iring diagram P 1 7 /1 7 Fig. D-6 [3] Connecting Connector Housing with Brush Holder Unit Rear cov er The side where Lead wires are drawn out must be placed on Rear co ver side as illustrated blow .
Een belangrijk punt na aankoop van elk apparaat Makita HK1820 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita HK1820 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita HK1820 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita HK1820 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita HK1820 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita HK1820 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita HK1820 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita HK1820 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
