Gebruiksaanwijzing /service van het product LS0711Z van de fabrikant Makita
Ga naar pagina of 32
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Slide Compound Sa w Equipped with Electric Blade Brake 1.
2 SPECIFICATIONS Blade diameter ........................................................................................... 190 mm (7-1/2”) Hole (arbor) diameter ................................................................................. 15.88 mm (5/8”) Max.
3 For Y our Own Safety Read Instruction Manual Bef ore Operating T ool Save it f or future reference GENERAL SAFETY PRECA UTIONS USA007-1 (F or All T ools ) 1. KNO W Y OUR PO WER TOOL. Read the owner’ s manual carefully . Learn the tool’ s applications and limitations, as well as the specific potential hazards peculiar to it.
4 19. CHECK D AMAGED P AR TS. Before further use of the tool, a guard or other part that is damaged should be carefully chec ked to determine that it will operate properl y and perform its intended fu.
5 ADDITIONAL SAFETY R ULES USB036-2 DO NO T let comf or t or familiarity with product (gained fr om repeated use) replace strict adherence to slide compound saw safety rules. If y ou use this tool unsafely or incorrectl y , y ou can suffer serious per sonal injur y .
6 19. Make sure the shaft lock is released before the s witch is turned on. 20. Be sure that the blade does not contact the turn base in the lowest position. 21. Hold the handle firmly . Be aware that the saw moves up or do wn slightly during start-up and stopping.
7 INST ALLA TION Benc h mounting When the tool is shipped, the handle is lock ed in the lowered position by the stopper pin. Release the stopper pin b y lower- ing the handle slightly and pulling the stopper pin. This tool should be bolted with two bolts to a le vel and stab le surf ace using the bolt holes provided in the tool’ s base.
8 If the see-through blade guard becomes dirty , or sawdust adheres to it in such a wa y that the blade is no longer easily visible , unplug the saw and clean the guard carefully with a damp cloth. Do not use solvents or an y petroleum-based cleaners on the plastic guard.
9 Maintaining maximum cutting capacity This tool is fa ctor y adjusted to provide the maximum cutting capacity f or a 190 mm (7-1/2 ” ) saw blade. When installing a new b lade, alwa ys check the lo wer limit position of the blade and if necessary , adjust it as follo ws: First, unplug the tool.
10 Adjusting the miter angle Loosen the grip by turning counterclockwise. T ur n the turn base while pressing down the loc k lev er . When you hav e mov ed the grip to the position where the pointer points to the desired angle on the miter scale, securely tighten the grip clockwise .
11 • Do not pull the s witch tr igger hard without pressing in the lock-off b utton. This can cause switch breakage . T o prev ent the switch trigger from being accidentally pulled, a lock-off b utton is provided. T o star t the tool, press in the lock- off button and pull the s witch trigger .
12 Socket wrenc h storage The sock et wrench is stored as shown in the figure. When using the sock et wrench, pull it out of the wrench holder . After using the sock et wrench, retur n it to the wrench holder .
13 Press the shaft lock to loc k the spindle and use the socket wrench to loosen the he x bolt clockwise. Then remo ve the he x bolt, outer flange and blade. T o install the blade, mount it carefully onto the spindle , mak- ing sure that the direction of the arrow on the surf ace of the blade matches the direction of the arro w on the blade case.
14 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy . T o attach the dust bag, fit it onto the dust nozzle. When the dust bag is about half full, remov e the dust bag from the tool and pull the f astener out.
15 V ertical vise The vertical vise can be installed in two positions on either the left or right side of the guide fence or the holder assemb ly (optional accessor y). Insert the vise rod into the hole in the guide f ence or the holder assembly and tighten the screw to secure the vise rod.
16 Holders and holder assembl y (optional accessories) The holders and the holder assembly can be installed on either side as a conv enient means of suppor ting workpieces horizontally . Install them as shown in the figure . Then tighten the screws firmly to secure the holders and the holder assembly .
17 1. Press cutting (cutting small workpieces) W or kpieces up to 50 mm (2 ” ) high and 97 mm (3-13/16 ” ) wide can be cut in the f ollowing wa y . Push the carriage toward the guide f ence fully and tighten the clamp screw on the turn base clockwise to secure the carriage.
18 • Ne ver perf or m the slide cut with the handle lock ed in the lowered position b y pressing the stopper pin. • Ne ver loosen the clamp screw which secures the carriage while the blade is rotating. This ma y cause serious injur y . 3. Miter cutting Ref er to the previously cov ered “ Adjusting the miter angle ” .
19 When perfo r ming compound cutting, ref er to “ Press cut- ting ” , “ Slide cutting ” , “ Miter cutting ” and “ Be vel cut ” e xplanations. 6. Cutting cro wn and cove moldings Crown and co ve moldings can be cut on a compound miter saw with the moldings laid flat on the turn base.
20 Example: In the case of cutting 52/38 ° type crown molding f or position (1) in Fig. A: • Tilt and secure be vel angle setting to 33.9 ° LEFT . • Adjust and secure miter angle setting to 31.
21 EN0002-1 Compound Miter Saw Miter and Bevel Angle Settings 000031 52 ˚ 38 ˚ Ceiling W all W all to Crown Molding Angle: 52/38 degrees W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel An gle (deg.) Miter Angle (deg.
22 EN0003-1 Compound Miter Saw Miter and Bevel Angle Settings 000032 45 ˚ 45 ˚ Ceiling W all W all to Crown Molding Angle: 45 degrees W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel An gle (deg.) Miter Angle (deg.) W all Angle (deg.
23 7. Cutting aluminum ex trusion When securing aluminum e xtr usions, use spacer b locks or pieces of scrap as shown in the figure to pre v ent def or mation of the aluminum. Use a cutting lubricant when cutting the aluminum e xtrusion to prev ent build-up of the aluminum material on the blade.
24 9. Cutting repetitive lengths When cutting se veral pieces of stoc k to the same length, ranging from 220 mm (8-5/8 ” ) to 385 mm (15-1/8 ” ), use of the set plate (optional accessor y) will f acilitate more efficient operation. Install the set plate on the holder (optional accessor y) as sho wn in the figure.
25 Carr y the tool b y carr ying grip as shown in the figure . If you remov e the holders, dust bag, etc., you can carry the tool more easily . CA UTION: • Alwa ys secure all moving por tions bef ore carr ying the tool. • Stopper pin is f or carr ying and storage purposes only and not f or any cutting operations.
26 Make sure that the pointer points to 0 ° on the miter scale. If the pointer does not point to 0 ° , loosen the screw which secures the pointer and adjust the pointer so that it will point to 0 ° . 2. Bevel angle (1) 0 ° be vel angle Push the carriage toward the guide f ence and tighten the clamp screw on the turn base to secure the carriage.
27 Make sure that the pointer on the arm point to 0 ° on the be vel scale on the arm holder . If it does not point to 0 ° , loosen the screw which secures the pointer and adjust the pointer so that it will point to 0 ° . (2) 45 ° be vel angle Adjust the 45 ° bev el angle only after perf or ming 0 ° be vel angle adjustment.
28 After use • After use, wipe off chips and dust adhering to the tool with a cloth or the like . Keep the b lade guard clean according to the directions in the pre viously covered section titled “ Blade guard ” . Lubricate the sliding por tions with machine oil to pre vent rust.
29 Fold Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitb y , Ontario L1N 7B7.
30 Y our answer s to the following questions are appreciated. Date Purchased Model No. Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Da y Y ear 20 Und.
31 F actory Ser vice Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “ tools ” or con- tact our customer service department (Tel) 1-800-263-3734 When you need service.
Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Een belangrijk punt na aankoop van elk apparaat Makita LS0711Z (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita LS0711Z heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita LS0711Z vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita LS0711Z leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita LS0711Z krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita LS0711Z bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita LS0711Z kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita LS0711Z . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
