Gebruiksaanwijzing /service van het product 20020107 van de fabrikant Masterbuilt
Ga naar pagina of 12
TURKEY FR YER WITH TIMER POTS NOT INCLUDED ON ALL MODELS CHECK P ACKAGING FOR DET AILS LP GAS CYLINDER NOT INCLUDED TOOLS NEEDED: ADJUST ABLE WRENCH, PHILLIPS HEAD SCREWDRIVER MODEL NUMBERS 20020107, 20020109, 20020209, 20020407, 20020507 FOLLOWING THESE INSTRUCTIONS WILL ALLOW YOU T O HA VE A SAFE COOKING EXPERIENCE.
1. Never operate this appliance unattended. 2. Never operate this appliance within 10 ft (3m) of any structure, combustible material or other gas cylinder . 3. Never operate this appliance within 25 ft (7.5 m) of flammable liquid. 4. Do not fill cooking vessel beyond maximum fill line.
W ARNING Cooking with Oil or Grease: • Failure to completely thaw and dry foods may cause oil or grease to overflow . When frying with oil or grease, all food products MUST be completely thawed and towel dried to remove excess water .
W ARNING • This Outdoor Gas appliance is for outdoor use only and shall not be used in a building, garage, tent or any other enclosed area. • Never use or operate this appliance on or under any overhead roof covering (car port), awning, overhang, apartment or condominium balcony or deck.
W ARNING Incorrect • Always perform soapy water test every time you use this appliance. • Avoid bumping or impact to the appliance to prevent spillage or splashing of hot liquid. • Always disconnect gas cylinder from appliance when not in use. • Keep hands, hair and face away from burner flame.
W ARNING • The use of alcohol, prescription or non prescription drugs may impair the consumer ’s ability to properly assemble or safely operate the appliance. • Do not obstruct flow of combustion and ventilation. Keep ventilation opening(s) of the cylinder enclosure free and clear of debris.
P ARTS LIST Remove nut (B) from bottom of burner . Place burner onto burner mount bar with burner bolt sticking down through hole in center of burner mount bar . NOTE: Do not over tighten. Threads should line up, do not damage threads by forcing hose into burner .
7 16 Our #1 Asked Question Y ellow Flame No Flame When the cast iron burner burns yellow or not at all, what should I do? If your burner does not burn, blows out, burns yellow , or there’s a flame inside the venturi, you need to check the burner venturi for any obstructions.
Thermometer Safety Check: • Before each use place the thermometer stem in boiling water and ensure that it registers approximately 212ºF +/- 20ºF (100ºC +/-10ºC). If it does not, contact Masterbuilt to order a replacement. • When thermometer is lowered into HOT oil, do not allow it to pierce into the turkey or food.
Regulator Control V alve Soapy W ater T est W arning and Procedures • The Soapy W ater T est must be performed each time gas cylinder is connected to appliance or each time the appliance is used. • The Soapy W ater T est must be performed outdoors in a well-ventilated area.
1. Check the regulator to be certain it is in the OFF position before connecting to the gas cylinder . Perform soapy water test before each use. 2. Open tank cylinder valve. 3. T o start timer operation, push POWER button; both lights will blink once.
11 12 SAFE ST ORAGE & MAINTENANCE • Before each use of the appliance, check and clean the burner/venturi tubes for insects and insect nests. A clogged tube can lead to a fire inside or behind the burner or beneath the appliance.
Een belangrijk punt na aankoop van elk apparaat Masterbuilt 20020107 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Masterbuilt 20020107 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Masterbuilt 20020107 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Masterbuilt 20020107 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Masterbuilt 20020107 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Masterbuilt 20020107 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Masterbuilt 20020107 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Masterbuilt 20020107 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.