Gebruiksaanwijzing /service van het product CF-08TX1A1M van de fabrikant Matsushita
Ga naar pagina of 87
ORDER NO. CPD0606050C1 Wireless Display CF-08TX1A1M This is the Service Manual for the follow ing areas. M …for U.S.A. © 2006 Matsushita Electric Industrial C o.
1.
2.
Precautions Care should be exercised with regard to the follo wing in order to avoid the possibility of overheating, fire or damage. Battery Pack A void Heat Do not throw the battery pack into a fire or expose it to excessive heat.
Do not touch the terminal s on the battery pack. The battery pack may no longer function prop erly if the contact s are dirty or d amaged. Do not expose the battery pack to water , or allow it to become wet.
CONTEN TS 1. S pec ifications ·················································································································· 1- 1 2.
Main Specifications Model No. CF-08TX1A1M CPU Intel ® PXA270 Processor 312 MHz Memory (ROM/RAM) 32 MB (Fl ash) /64 MB Display Method 10.4 XGA type Internal LCD Display 65,536 colors (1024 × 768 pixels) W i r e less LAN B u i lt- i n Blu e t o oth B u i lt- i n LAN IEEE 802.
*1 This slot does not support the MultiMedia card. Operation has been confirmed for Panas onic SD Memo ry Cards with up to 2 GB capacity . *2 Theoretical value and not the actual speed. The transfer rate does not become higher even if you use a card tha t supports the higher transfer rate.
2 Introduction Copyright This manual is copyrighted by Matsushita Electric Indu strial Co., Ltd. with a ll rights reserved. No p art of this manual may be r eproduced in any form with out the prior written permission of Mat sushit a Electric Industrial Co.
3 Description of parts A. LCD (T ouchscreen) B. Wireless LAN antenna C. Bluetooth anten na D. Power st atus E. Power button F . Batter y st atus G. D C - I N j a c k H. LAN port I. Cursor control button J. Keyboard b utton K. USB port L. USER button M.
The tether can be att ached to the upper r ight or upper lef t corner of the di splay . It prevents the pen (included) from falling accident ally . Att aching the T ether Using the T ethe r 1 3 2 4 3 .
4 Starting up/Shutting Down St arting Up 1 T urn on the wireless display . When you log on as a Super visor When you log on as a User Press the power b utton with the USER button pressed. • If you do not do so, even when you set enter the Supervisor Password, the wireless display will run in the User operating environment.
A. Auto Launch B. W a it for Network Connection • When the Su pervisor does not add the check mark for [Allow Change Auto Launch] in the [User] ta b of the [Security Set- tings (Supervisor)] screen, [Auto Launch] and [W ait for Network Connection] cannot be set here.
When returning the wireless displa y to its condition at the time of shipment Perform the following pr ocedure while the wire less display is turned off.
OCCURRENCE OF TROUBLE END OF REPAIR WORK Self Test Program NORMAL FINISH ERROR OCCURRENCE TROUBLESHOOTING DISASSEMBLY PROCEDURE Replace defective parts. Self Test Program After repair, make sure that the repaired set operates properly. TEST OK DEFECTIVE PARTS SORTING REPAIR WORK INSPECTION OK FAULT Insert the AC plug.
5.2. Troubleshooting Please t ake n ote of the follow ing two p oint s w ith rega rd to t roubles hooting: 1. Know-h ow of diagnosis u pon o ccurrence of heavy t roubles, e.g. ‘Set cannot be turn ed ON’, ‘ Set f ails to start’ , ‘No di splay o n screen’, etc .
5.3. Self Test Program 1. Introduction This description explains Self- Test Program of this Test. 2. How to Start-up (1) Connect the AC adapto r. ( Unless you connect the AC adapto r, the Self- Test Program does not start. ) (2) Connect the AC adapto r.
5-4 3.1.3. Test register check for the source microcompute r. Check the test register of the source microcomputer 3.1.4. ID check for 2700G Confirm the ID of 2700 G. 3.1.5. Chip ID check for LAN9 118 Check the test register and chip ID of LAN9 118. 3.
If the results of all items are OK, the following display appears. *** SELF TEST *** CPU Type : OK SDRAM March Test : OK Embedded Controller : OK 2700G : OK LAN9 118 : OK PCMCI A : OK Overall Result : OK If only the PCMCI A result is N G , the following display appears.
6 Troubleshooting Follow the instr uctions below whe n a problem has occur red. For a sof tware pr ob- lem, refer to the sof tware’ s instructio n manual. If the problem persist s, cont act your technical support of fice. St arting Up Display T ouchscreen Cannot sta rt up.
Shut Down Sound Wireless Communication Connecting Peripherals Cannot shut down. Press the power button for fo ur seconds or longer to shut down the wireless display . No sound. Confirm the volume for [Qu ick Menu] or [V olume & Sounds] in Control Panel.
7 Block Diagram Intel PXA270 C5 Bulverde Micropro cessor I/O 1.8V 13MHz-312MHz ,Core 0.85-1.3V CF-08 Block Diagram Crystal 13.000MHz 32.786KHz AC97 I/F Power-MG I2C I/F AC97 Codec with Touch screen co.
AC Adapter (16V/2.5A) FET Voltage Detector & OVP# Main DC/DC LDO (MAX1586) VA3 VCC_CORE(0.8-1.3V) VA3 Charger (LTC40 08) NTC FET Battery 5200mAh 7.4V Voltage Regulator 3.4V Sub Battery Connector PWR_EN SYS_EN VCC_SRAM(1.1V) VCC_PLL(1.3V) Voltage Detector R ACIN VCC_USIM(3.
8 Wiring Connection Diagram USB PCB IO POWER PCB SW LED PCB MAIN PCB DOCK CON PCB WLAN PCB AUDIO CON PCB LCD Connector by Cable Direct connection by Connectors Parts on Bottom Side SPEAKER ANTENNA PCB.
9-1 9 Disassemb ly/R eassembly Note: Power off the c omputer . Do not shut down to the Suspend o r hibernatio n mode. Do not add peripherals w hile the com puter is i n the Susp end or hib ernation mode ; abnormal operation may result. 9.1. Disassembly Inst ructions 9.
9-2 3. Remove the 12 Screw s <N6 >. 4. Remov e the Cable Ho ld Sheet while ope ning the Rear Cabinet ASS'Y slowl y . 5. Remove the Ca ble ho oked on t he Lam p Cable S p ring. 6. Remove both the Inverter an d the I nverter Case. 7. Remove the Conn ector (CN6) co nnect ed to the IO Power PCB.
9-3 9.1.6. Removing th e WLAN PC B 1. Remove the two Antenna Cables . 2. Remove the four Sc rews <N1> . 3. Remove the La mp Cab le S pring. 4. Remove the WLAN PCB. Screws <N1>:XSB2+4F NL 9.1.7. Removing the Audio Con PCB 1. Disconnect the Ca ble fro m the Co nnect or (CN30 0).
9-4 9.1.10. Removing the WLAN L PCB 1. Remove the Ins ulation She et. 2. Remove the Screw <N7>. 3. Remove both the Ante nna Cab le and the WL AN L PCB. Screw <N7>:DFHE5025 XA 9.1.1 1. Removing the Bluetooth WLAN R PCB 1. Remove the t wo ta pes.
9-5 9.1.14. Removing the LCD Unit and t he Inverter 1. Disconnect the Ca ble fro m the I nverter Connec tor . 2. Remove the Inve rter wi th the I nverter C ase. 3. Remove the Pet T ape. 4. Remove the TS Noise T ap e. 5. Remove the Cab le from th e Cla mper .
9-6 9.2. Reassembly Instructi ons 9.2.1. A ttention whe n CF-0 8 series is rep aired • Please ex ecute writing BI OS ID w hen you e xchange the M ain Boa rd. • Parts (She et and rubber) e tc. relate d vario us the Con ductiv e Cloth and Hea t S preader cannot b e recy cled.
9-7 ■ Prep aration s for back light LCD Prism Sheet LCD Prism Sheet LCD Prism Sheet LCD Panel Frame LCD Panel Frame T ape Holder Sheet Holder Sheet 1 A 0~0.5mm 0~0.5mm 0~0.5mm Insert into the inside the ribs. (4 places in total) wide side Remove the protection films.
9-8 ■ Assembly o f the LCD LCD Refrection Sheet Holder Sheet Holder Sheet LCD Refrection Sheet LCD Refrection Sheet Prism Sheet LIGT GUIDE PANEL LCD FRAME 0~0.5mm Insert after attaching 1. Make the silver side inside. Insert into the inside the ribs.
9-9 LCD PWB Sheet Refrect T ape Pet T ape 1 CN 0~0.5mm Standard attaching position of 1 Match to the PWC outline. Run over the end of the CN metal (0.5 to 1 mm) Parts for electricity removing work Press the Sheet along the edge of the Reflector (Avoid floating.
9-10 ■ Prep arati ons for T ouchscreen ■ Asse mbly of th e T ou chsc reen Front Case Assy TS T ape Attachment Standard Attachment Standard Attachment Standard TOUCH SCREEN ASSY TOUCH SCREEN ASSY P.
9-1 1 ■ Assembly of the LCD Block 9.2.3. Setting the SW LED P CB 1. Connec t the Ca ble to the con necto r (CN501) o f the SW LED PCB. 2. Attac h the tape. 3. Fix the SW LED PCB and SW Board S topper Plate usin g three Screws <N2> . No1 to No3 4.
9-12 ■ Assembly o f the SW LED PCB LED Lens SW Rubber Power Button Power Button Sheet SW Board T ape SW Board Stopper Plate Screw-2 Screw-3 Screw-1 T ape Scroll Button Sheet Scroll Button User Button 1~2mm 0~1mm Attach. Asymmetric shape Ensure it is attached in the notch.
9-13 9.2.4. Setting the Dock Con PCB 1. Fix the Doc king PCB Sheet, the Bas e Joint Cover and the Dock Con PC B using f ive Screws <N3>. No1 to No5 2. Connec t the two C ables to th e two con nectors (CN600, CN601) of the Dock Con PCB. 3. Attac h the FFC Hold Cush ion.
9-14 ■ Assembly of the DOCK CON PCB Base Joint Cover Docking PCB Sheet FFC Hold Cushion Cradle Relay Card FFC (Docking Card) Busterade Screw-4 Screw-3 Screw-5 Screw-1 Screw-2 Caption T ape 0~1mm 10+1mm Ensure the direction is right. Attach to the top side of CN.
9-15 9.2.5. Setting the Bluetooth WLAN R PCB 1. Fix the Antenna Ca ble and the Bluetooth WLAN R PCB using on e Screw <N7 >. 2. Fix the Antenna C able s with t he two t apes . Screw <N7> :DFHE5025XA 9.2.6. Setting the WLAN L PCB 1. Fix th e Antenna C able an d the W LAN L PC B using on e Screw <N7>.
9-16 9.2.7. S etting the U SB PCB 1. Fix the USB Hold Plate and the USB PCB using two Screws <N1>. 2. Attach the Edg e Sheet. Screws <N1>:XSB2+4 FNL 9.2.8. S etting t he S peake r 1. Attach the S peaker . 2. Fix the S peaker Hold S heet usin g two Scre ws <K 1-1-2>.
9-17 9.2. 10. Setti ng the W LAN PCB 1. Fix the WLAN PCB and the lamp Ca ble S pring usin g four Screws <N1>. 2. Fix the two Antenna Cables . Screws <N1>:XSB2+4F NL 9.2. 1 1 . S etti ng th e IO Pow er P CB 1. Fix th e IO Power PCB u sin g eigh t Sc rews <N1> .
9-18 9.2.12. Set ting the M ain PCB 1. Connect the Ca ble to the Conn ector (CN7 ) of the Main PCB. 2. Fix the Main PCB using four Scre ws <N1>. No1 t o No4 3. Connect the Ca bles to th e six C onnectors (CN3,CN4,CN9,CN10,CN12,CN13) of the Main PCB.
9-19 ■ Assembly of the USB PCB, Audio Con PCB, WLAN PCB, I O Power PCB, and Main PCB Lamp Cable Spring Edge Sheet WLAN PCB BA TT CN Cover Sheet Audio Con PCB Screw x2 Screw x4 Screw x8 4 1 2 3 5 3 2 4 6 1 7 8 a b IO Power PCB Screw x4 1~2mm 1~2mm Hook on the boss and tighten together with the Board.
9-20 Shield T ape BT FFC Edge Sheet Shield T ape FFC (Wireless Card) FFC (Wireless Card) Busterade Edge Sheet T ape T ape Power Cable FFC(Audio Card) FFC(Audio Card) A a b c Shield T ape 0~1mm 1~3mm 1~3mm 0~0.5mm 0~0.5mm 1 0.5mm * Paste Sheets firmly .
9-21 9.2.13. Setting the Display Unit 1. Conn ect the C ables to th e conn ectors (CN 2, CN6) of th e Main PCB. 2. Put the two Cable s into the Clampe r . 3. Connec t the Inverte r Cable to t he con nector (CN6 ) of the Pow er PCB as clo sin g the Re ar Ca binet .
9-22 8. Fix the Rear Ca se ASS'Y usi ng 12 Sc rews <N6>. No1 to No12 9. Fix the Antenna Cove r R using t wo Screw s <N4>. 10. Fix the Antenna Cove r L using two Screw s <N4> . Note: T ighte n the Screw s in the numbered order (No1 to No12 ).
9-23 Cable Hold Sheet A A B *Note Ensure the Cable does not run over the Cushions (a,b,c). Note Avoid any stress on the transformer and the coil. Insert the cushions on the both sides with the "Caution to High Voltage" label facing front until they reach the bottom while matching the cushions to the A boss and the rib.
9-24 9.2.14. Set ting the Bat tery Pa ck 1. Open the hand strap cov er . 2. Re move th e hand strap. 3. Sl ide th e Bat tery c over l atc h. 4. Open and remo ve the Battery cove r . 5. F irmly attach the ba tter y pack t o the c onnec tor . 6. Fit the battery co ver , and then clos e the b attery cover .
9-25 ■ Assembl y of the Ba ttery Pack Pen Battery Cover Assy Battery Pack Coa Label(Win Ce) Information Label Model Label Serial Label 10~15mm Important Parts for Safety Important Parts for Safety guide to match the end –2 mm Allowable displacement: max.
9-26 Screw Screw Hand Strap Ensure the direction is right. The side with fewer stitches is placed on the surface. Turn the metal clasp on both sides to the inside.
CF-08TX1A1M 10 Exploded V iew N7 N7 N7 N3 N3 K8 K51 K53 E6 K42 K29 K45 E14 E16 E16 K26 K9 K10 K10 K43 K50 K18 K20 K19 K22 K7 K28 K48 K6 K5 K21 K16 E7 N7 N7 N6 N6 N6 N6 N6 N6 N6 N6 N6 N6 N7 N7 N3 N3 E8.
CF-08TX1A1M K1 K1-1-7 K1-1-5 K1-1-13 K1-1-1 K1-1-4 K1-1-6 K1-1-3 K1-1-12 K1-9 K1-2 K1-6 K1-3 K1-10 K1-3 K1-6 K1-3 K1-7 K1-7 K1-8 K1-7 K1-8 K1-1-12 K1-1-14 K1-1-1 1 K1-1-9 K1-1-10 K1-1-8 K1-1-2 K1-1 K1-5 K1-4 Capton tape (10 25) Capton tape (10 25) Screw tightening torque 0.
CF-08TX1A1M A A K200 K31 K33 E3 K17 K30 K2 N2 N2 K32 K200-4 K200-3 K200-3 K200-6 K200-4 K200-1 K200-4 K200-3 K200-2 K200-2-1 K11 K14 E19 E19-1-1 E19-2 E19-1-2 E20 K201 E19-3 E19-1-3 E19-1 K201 K13 K27 E10 E12 E13 K38 K200-2-6 K200-2-3 K200-2-2 K200-2-5 K200-2-4 K200-2-5 K200-2-6-1 K200-3 K37 K37 K200-4 K200-5 Screw tightening torque 0.
11 Replacement Parts List Note: Important Safety Notice Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer's specified parts. CF-08TX1A1M REF.NO. and AREA PART NO.
K1-1-7 DFHR3C73ZA SPEAKER HOLD SHEET 1 K1-1-8 DFHR3C75ZA BATTERY BOTTOM BLIND SHEET 1 K1-1-9 DFHR3C76YA USB SHEET 1 K1-1-10 DFHR3C78ZA LAN SHEET 1 K1-1-11 DFHR3C79ZA SD SHEET 1 K1-1-12 DFHR3C80ZA PEN HOLD SHEET 2 K1-1-13 DFHR3C82ZA MAIN PCB INS.
K43 DFHR3C43ZA-0 CARD BLIND SHEET 1 K44 DFHR3C74ZA BATTERY CN COVER SHEET 1 K45 DFHR3C77YA AUDIO SHEET 1 K46 DFHR3C81YA MAIN PCB HOLD SHEET 1 K47 DFHR3E39ZA CAPTON TAPE 1 K48 DFHR6207ZA PEN 1 K49 DFHR.
Replacement Parts List CF-08TX1A1M PART NO. DESCRIPTION Q'TY MAIN PCB C 1 F1G1E103A062 CAPACITOR, 25V, 0.01µF 25 C1 0 C5 0 C 150 C 151 C 164 C 169 C 171 C 187 C 188 C 207 C 245 C 247 C 250 C 266 C 278 C 279 C 280 C 311 C 312 C 313 C 314 C 324 C 325 C 326 C 5 F1G1H1R0A543 CAPACITOR, 50V, 1pF 1 C 7 F1G1A104A014 CAPACITOR, 10V, 0.
C2 7 C2 8 C2 9 C3 0 C3 1 C3 2 C3 3 C3 4 C3 5 C3 6 C3 7 C3 8 C3 9 C4 0 C4 1 C4 2 C4 3 C4 4 C4 9 C5 2 C5 3 C5 5 C5 6 C5 7 C6 5 C6 6 C6 7 C6 8 C6 9 C7 0 C7 1 C7 4 C7 5 C8 1 C8 2 C8 3 C8 4 C8 5 C8 6 C8 7 .
C9 8 C 102 C 103 C 104 C 105 C 106 C 107 C 108 C 109 C 110 C 111 C 112 C 113 C 114 C 115 C 116 C 117 C 118 C 119 C 120 C 121 C 122 C 125 C 126 C 127 C 138 C 139 C 140 C 141 C 142 C 147 C 148 C 152 C 1.
C 232 C 233 C 234 C 239 C 241 C 265 C 274 C 276 C 277 C 281 C 282 C 283 C 284 C 285 C 286 C 287 C 288 C 293 C 294 C 295 C 296 C 297 C 298 C 299 C 300 C 301 C 303 C 304 C 306 C 310 C 315 C 316 C 317 C .
C 221 C 229 C 231 C 235 C 257 C 258 C 259 C 262 C 263 C 268 C 308 C 100 F1J0J1060004 CAPACITOR, 6.3V, 10µF 23 C 101 C 124 C 135 C 137 C 149 C 174 C 183 C 190 C 191 C 236 C 237 C 238 C 242 C 246 C 248.
C 240 C 243 C 227 F1G1H100A452 CAPACITOR, 50V, 10pF 2 C 228 C 251 F1J0J226A048 CAPACITOR, 6.3V, 22µF 6 C 253 C 269 C 336 C 337 C 338 C 260 F1G1H331A450 CAPACITOR, 50V, 330pF 3 C 261 C 264 C 267 F1G1H332A496 CAPACITOR, 50V, 3300pF 1 C 270 EEFUD0J101ER CAPACITOR, 6.
IC 11 IC 15 C3FBRY000001 IC, FLASH MEMORY 1 IC 16 C3ABPY000009 IC, SDRAM 1 IC 19 C0CBCAC00161 IC 1 IC 22 C0JBCZ000523 IC 1 IC 23 C0JBAZ002770 IC, LOGIC 1 IC 26 C0JBAZ002758 IC, LOGIC 1 IC 27 C0JBAZ002.
Q4 4 Q 27 UNR9113J0L TRANSISTOR 3 Q3 3 Q3 6 Q 34 XP0421300L TRANSISTOR 3 Q3 5 Q3 8 R 1 ERJ2GEJ473X RESISTOR, 1/16W, 47K Ω 21 R2 8 R2 9 R3 0 R3 1 R3 2 R3 3 R3 6 R3 8 R 168 R 171 R 177 R 178 R 179 R 31.
R 265 R 275 R 277 R 279 R 283 R 284 R 292 R 325 R 327 R 7 ERJ2GEJ103X RESISTOR, 1/16W, 10K Ω 11 R8 R9 R2 4 R3 7 R4 3 R 243 R 244 R 253 R 255 R 256 R 10 ERJ2GEJ100X RESISTOR, 1/16W, 10 Ω 16 R1 1 R1 2 R1 3 R1 4 R1 5 R1 6 R1 7 R1 8 R1 9 R2 0 R2 1 R2 7 R4 6 R 187 R 331 R 22 ERJ2GEJ122X RESISTOR, 1/16W, 1.
R 221 R 222 R 223 R 357 R 358 R 359 R 360 R 35 ERJ2GEJ104X RESISTOR, 1/16W, 100K Ω 58 R4 9 R7 7 R7 8 R8 9 R9 2 R9 4 R9 6 R9 8 R9 9 R 101 R 102 R 103 R 108 R 111 R 112 R 113 R 114 R 117 R 133 R 134 R .
R 224 R 235 R 245 R 252 R 259 R 260 R 261 R 262 R 287 R 319 R 320 R 341 R 344 R 345 R 346 R 39 ERJ3GEY0R00V RESISTOR, 1/16W, 0 Ω 18 R4 2 R5 3 R7 0 R7 4 R 107 R 123 R 124 R 127 R 129 R 132 R 143 R 269.
R 361 R 362 R 363 R 364 R 365 R 366 R 204 ERJ2RKF49R9X RESISTOR, 1/16W, 49.9 Ω 4 R 205 R 206 R 207 R 210 ERJ3EKF1202V RESISTOR, 1/10W, 12K Ω 1 R 211 ERJ3EKF1242V RESISTOR, 1/10W, 12.4K Ω 1 R 236 ERJ2GEJ101X RESISTOR, 1/16W, 100 Ω 9 R 237 R 238 R 239 R 240 R 290 R 291 R 367 R 368 R 246 ERJ2GEJ472X RESISTOR, 1/16W, 4.
C6 0 C6 1 C6 2 C6 8 C7 3 C 4 F1J0J1060004 CAPACITOR, 6.3V, 10µF 6 C5 C4 4 C5 5 C5 6 C5 8 C 6 F1G1E103A062 CAPACITOR, 25V, 0.01µF 7 C1 1 C4 7 C4 8 C6 9 C7 0 C7 1 C 8 F1H1H104A748 CAPACITOR, 50V, 0.
C 35 F1G1H220A542 CAPACITOR, 50V, 22pF 4 C3 8 C7 6 C7 9 C 36 F1G1H221A450 CAPACITOR, 50V, 220pF 2 C3 7 C 52 F1H0J1050022 CAPACITOR, 6.3V, 1µF 1 C 63 F1G1A683A014 CAPACITOR, 10V, 0.
IC 1 C0ZBZ0001023 IC 1 IC 3 C0ABZA000047 IC, AMP 1 IC 4 C0ABBA000093 IC, OP AMP 1 IC 5 C0DBDJH00009 IC, LINEAR 1 IC 6 C0DBALH00003 IC 1 IC 7 C0EBH0000336 IC 1 IC 8 C2CBYY000186 IC, MICROCONTROLLER 1 I.
R6 R7 R8 R2 9 R8 1 R 101 R 9 ERJ2GEJ103X RESISTOR, 1/16W, 10K Ω 11 R1 0 R2 2 R4 7 R7 0 R7 3 R7 4 R 108 R 109 R 110 R 111 R 11 ERJ2GEJ104X RESISTOR, 1/16W, 100K Ω 19 R1 2 R2 3 R2 4 R2 5 R2 6 R 137 R .
R 27 ERJ2GEJ105X RESISTOR, 1/16W, 1M Ω 1 R 28 ERJ2GEJ3R3X RESISTOR, 1/16W, 3.3 Ω 1 R 30 ERJ2GEJ562X RESISTOR, 1/16W, 5.6K Ω 4 R3 1 R3 2 R5 0 R 33 ERJ2RHD103X RESISTOR, 1/16W, 10K Ω 3 R3 4 R8 3 R 35 ERJ2RKF1003X RESISTOR, 1/16W, 10K Ω 3 R3 6 R4 8 R 37 ERJ2RKF1503X RESISTOR, 1/16W, 150K Ω 2 R3 8 R 39 ERJ3GEYJ562V RESISTOR, 1/16W, 5.
R9 8 R 140 R 160 R 99 ERJ6GEYJ222V RESISTOR, 1/10W, 2.2K Ω 2 R 100 R 102 ERJ2GEJ223X RESISTOR, 1/16W, 22K Ω 1 R 122 ERJ2GEJ102X RESISTOR, 1/16W, 1K Ω 5 R 123 R 126 R 127 R 141 R 143 ERJ2RKF75R0X RESISTOR, 1/16W, 75 Ω 2 R 144 R 145 ERJ2RKF49R9X RESISTOR, 1/16W, 49.
C 303 C 304 F1J0J1060004 CAPACITOR, 6.3V, 10µF 2 C 308 C 305 F1G0J224A001 CAPACITOR, 6.3V, 0.22µF 1 C 306 F1G1A104A014 CAPACITOR, 10V, 0.1µF 4 C 309 C 310 C 311 C 307 F1G1H471A496 CAPACITOR, 50V, 4.
CN 3 K1QZA1AE0001 CONNECTOR 1 F 1 K5H5011A0015 FUSE, 5A 1 IC 1 N5HZD0000006 IC, LAN MODULE 1 IC 2 N5HZZ0000045 IC, BLUETOOTH MODULE 1 R 4 ERJ2GEJ104X RESISTOR, 1/16W, 100K Ω 1 L 2 J0JDC0000045 INDUCT.
CF-08 Printed Circuit Board 1 3 7 2 4 5 6 8 BC D F H L A EG I J K Main PCB.
1 3 7 2 4 5 6 8 BC D F H L A EG I J K Main PCB.
1 3 7 2 4 5 6 8 BC D F H L A EG I J K Dock Con PCB Audio Con PCB USB PCB SW LED PCB IO Power PCB.
IO Power 1 I/F CONNECT OR CF- 08 Schematic Diagram Note: All Schematic Diagrams are confidential. 11 10 9 8 7 6 5 4 3 2 1 BC D F H A EG I J SD slot(Reverse) SIGN50660 SDVCC SDVCC PXSDCLK SDDET# PXSDD2 C3 0.1u SDWP PXSDD1 SDVCC R10 10k FPS009-2608-0(01) CN3 1 2 3 4 5 6 7 8 9 10 12 11 13 6.
IO Power 2 DCIN/ BA TTER Y 11 10 9 8 7 6 5 4 3 2 1 BC D F H A EG I J NJM12904V(TE1) IC4 - 2 1 O + 3 SMBCLKE C13 0.1u R42 0.1 NJM12904V(TE1) IC4 V- 4 V+ 8 VSEL R40 0.
IO Power 3 CHARGER 11 10 9 8 7 6 5 4 3 2 1 BC D F H A EG I J C24 10u 25V B R53 3K 0.5% R49 36.5K 1% CHGPWM CHGEN CHARGE DCIN PGND PGND PGND UNR9213J0L Q13 3 1 2 #919AS-160M=P3 L6 1 2 R55 100k 0.
IO Power 4 V A3,V A5 11 10 9 8 7 6 5 4 3 2 1 BC D F H A EG I J Nch-MOSFET Nch-MOSFET 1608 3225 C C A 1005 1005 1005 1005 A A C 1005 2012 3225 1005 1608 1608 1608 1005 1005 1005 1005 1005 1005 1005 100.
IO Power 5 EC 11 10 9 8 7 6 5 4 3 2 1 BC D F H A EG I J 005:E7 2012 001:H6 005:E7;005:G10 005:E7 005:E7 002:D4 002:E8;005:B8;005:D3 005:D10;005:F3 002:F10;005:A11;005:C6 003:C8 002:E8;005:A8;005:D3 00.
IO Power 6 OVERPROTECT 11 10 9 8 7 6 5 4 3 2 1 BC D F H A EG I J 03P2J-T2-AZ D28 2 3 1 UDZS6.2B D31 2 1 UDZS6.2B D30 2 1 DAN222 D27 2 1 3 ACIN R105 100 BATVOL R99 2.
WLAN 1 SYCHIPWLAN/ BT BOARD 11 10 9 8 7 6 5 4 3 2 1 BC D F H A EG I J.
WLAN 2 SYCHIPWLAN/ BT BOARD 11 10 9 8 7 6 5 4 3 2 1 BC D F H A EG I J.
Een belangrijk punt na aankoop van elk apparaat Matsushita CF-08TX1A1M (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Matsushita CF-08TX1A1M heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Matsushita CF-08TX1A1M vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Matsushita CF-08TX1A1M leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Matsushita CF-08TX1A1M krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Matsushita CF-08TX1A1M bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Matsushita CF-08TX1A1M kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Matsushita CF-08TX1A1M . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
