Gebruiksaanwijzing /service van het product TE653ELW-M van de fabrikant Meade
Ga naar pagina of 24
TE653ELW-M Complete Weather Forecaster with Indoor/ Outdoor Temperature and Humidity USER MANUAL MADE IN CHINA.
INTRODUCTION Thank you for selecting a Meade Instruments W eather Forecaster . This device combines precise time keeping, monitoring and displaying of current temperature data from up to three remote locations (additional sensors are required).
INST ALLA TION Communications between the main unit (receiver) and the remote sensor (transmitter) is wireless. This allows you to greater flexibility in choosing the location of remote sensor . The remote transmits data up to 164 feet (50 meters) over an open, unobstructed area.
4 REMOTE SENSOR FEATURES • Remote temperature transmission to the main unit via 433 MHz signal • Case can be wall mounted using built-in hanger • 164 feet transmission range without interference.
PLACEMENT • The remote sensor should be placed under eaves or a similar location with free air circulation, sheltered from direct sunlight and extreme weather . • Ideally , place the remote sensor over soil, rather than asphalt, which would cause false readings.
FRONT REAR 6 MADE IN CHINA A H G F E B L I D J K C M N O.
A. WEA THER FORECAST/ PRESSURE window B. TEMPERA TURE/ HUMIDITY window C. CLOCK window D. DOWN button • Select the next available mode • Press and hold for 2 seconds to search for wireless signal from remote sensor .
BA TTERY INST ALLA TION • Remove the battery door located at the back of the main unit. • Insert two (2) AA batteries and replace the battery compartment door . PLACEMENT • Make sure that the main unit is locating within the operating range of all remote sensors.
PRESSURE OPERA TION The pressure window displays: current barometric pressure, sea level pressure, and weather forecast. The information contains a number of historical statistics: pressure/ temperature/ humidity history bar -chart for the past 24 hours.
New Moon W aning Crescent First Quarter W axing Gibbous Full Moon W aning Gibbous Last Quarter W aning Crescent CHANGING PRESSURE AND ALTITUDE UNITS • Press MODE as needed, until “LOCAL” pressure is displayed. • Press and hold HISTOR Y , until the pressure unit is flashing.
Icon Status Searching for the signals from the remote sensor Corresponding remote sensor signal received successfully No signals received for over 1 hour REMOTE SENSORS ST A TUS The wave icon above th.
VIEWING MAX/MIN AND MINIMUM READINNGS Press the MEMORY button recalling: • Current temperature and humidity • Minimum temperature and humidity • Maximum temperature and humidity at the remote location.
ICON Atomic Time Reception Strength Undefined data (Flashing) No Reception for the past 24 hours W eak signal, but can be decoded Strong signal • The atomic clock receiver is programmed that it will search for the atomic time signal daily for 0:00, 3:00, 6:00, and 12:00 am.
CLOCK ALARMS There are two time alarms – Weekday alarm ( W ) and Single day alarm ( S ) - and one Ice Warning Alarm ( PRE-AL ). • If Weekday (W) alarm is activated, it will sound at the set time a.
Issue Main unit Radio Controlled T ime signal is not received Cannot locate remote sensor Cannot change the channel Data does not match data on the main unit Place unit by the window and keep it there.
BA TTERY INST ALLA TION • Remove the battery door located at the back of the main unit. • Insert two (2) AA batteries and replace the battery compartment door . PLACEMENT • Make sure that the main unit is locating within the operating range of all remote sensors.
PRESSURE OPERA TION The pressure window displays: current barometric pressure, sea level pressure, and weather forecast. The information contains a number of historical statistics: pressure/ temperature/ humidity history bar -chart for the past 24 hours.
New Moon W aning Crescent First Quarter W axing Gibbous Full Moon W aning Gibbous Last Quarter W aning Crescent CHANGING PRESSURE AND ALTITUDE UNITS • Press MODE as needed, until “LOCAL” pressure is displayed. • Press and hold HISTOR Y , until the pressure unit is flashing.
Icon Status Searching for the signals from the remote sensor Corresponding remote sensor signal received successfully No signals received for over 1 hour REMOTE SENSORS ST A TUS The wave icon above th.
VIEWING MAX/MIN AND MINIMUM READINNGS Press the MEMORY button recalling: • Current temperature and humidity • Minimum temperature and humidity • Maximum temperature and humidity at the remote location.
ICON Atomic Time Reception Strength Undefined data (Flashing) No Reception for the past 24 hours W eak signal, but can be decoded Strong signal • The atomic clock receiver is programmed that it will search for the atomic time signal daily for 0:00, 3:00, 6:00, and 12:00 am.
CLOCK ALARMS There are two time alarms – Weekday alarm ( W ) and Single day alarm ( S ) - and one Ice Warning Alarm ( PRE-AL ). • If Weekday (W) alarm is activated, it will sound at the set time a.
Issue Main unit Radio Controlled T ime signal is not received Cannot locate remote sensor Cannot change the channel Data does not match data on the main unit Place unit by the window and keep it there.
MADE IN CHINA Meade Instruments Corp. 27 Hubble Irvine, CA 92618 U.S.A. ©201 1 Meade Instruments Corp. All Rights Reserved. All user manual contents and information are subject to change.
Een belangrijk punt na aankoop van elk apparaat Meade TE653ELW-M (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Meade TE653ELW-M heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Meade TE653ELW-M vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Meade TE653ELW-M leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Meade TE653ELW-M krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Meade TE653ELW-M bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Meade TE653ELW-M kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Meade TE653ELW-M . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
