Gebruiksaanwijzing /service van het product AfterBurner van de fabrikant MegaTech
Ga naar pagina of 20
Entire Contents ©2005 Megatech International O WNERS MANU AL ®.
Getting Acquainted with Y our AfterBurner .....................................3 Safety W arnings ...............................................................................3 The Radio System .......................................................
Review the components of the AfterBurner to ensure that your kit is complete before you begin fi nal assembly . (See Figure 1 ) Kit Contents: A. AfterBurner Nitro-Powered High-Speed Funny Car B. 2-Channel Radio T ransmitter C. Body W ashers and Clips D.
This vehicle is not a toy and must be operated by an adult who will handle this car safely and take responsibility to avoid any injury . This model is designed to be operated only in appropriate areas.
Fuel is the most critical component for making your engine perform properly . Improper fuels will cause hard starting, poor performance, and excessive wear on the engine. Fuel for your vehicle must contain a blend of BOTH synthetic oil and castor oil.
Remove the antenna from the slot on top of the transmitter . Slide it into the hole on top of the transmitter and turn clock wise until snug. Do not over-tighten. A. Be sure that both the transmitter and receiver switches are in the “off” position.
the throttle trigger operates the slide carburetor . If the servos do not respond, remove the batteries and make sure they are installed correctly . E. T urn off the power switch on the car and then on the transmitter . Although your AfterBurner comes factory-assembled, it is important to fi nely adjust the steering trim before operating.
Important! For best performance, maximum enjoyment and longest service, your Q 1.6 HP engine must be properly broken in before you adjust it for maximum power . Breaking in your engine enables match- ing surfaces and parts to establish the correct running tolerances.
Figure 9 - Closing the high speed valve First, fully extend your antenna and turn the transmitter on. If the green light ever goes dark or the red light comes on, your transmitter batteries are low . Y ou should replace them right away . Next turn on the car ’ s receiver .
for another full tank of fuel. Be careful not to maneuver it too harshly or use any more than half throttle. T o adjust the high speed needle valve, carefully turn the high speed needle valve clockwise 1/8 of a turn at a time. This allows the engine to run faster and at a higher pitch sound.
The Brake System Before running your AfterBurner , be sure to do a brake check. W ith the car runing at idle, roll it forward. It should roll freely . Now roll the car forward again and push the throttle trigger forward. The car should come to a stop almost immediately .
Proper care and simple maintenance should keep your AfterBurner running well for a long time. Make sure you thoroughly check your vehicle after each run to make sure no parts were bent or broken. Also check to make sure the screws, fasteners, bolts and hardware are secure and tight after each run.
13 Parts Listing P ar ts Listing Part# Description 1685 5*8*2.5 Premium Bearing (2 Pack) 16109 Side Exhaust Header 780201 Air Filter 780203 Flywheel 780204 Radio Box 780205 2-speed Spur Gear 42t 780206 2-speed Spur Gear 38t 780207 Suspension Hinge Pins (50mm) 780215 Brake Pads (Pr) 780218 Brake Disc 780222 Suspension Arms 780224 Upper Arms (Pr .
780204 780243 780243 781043 780225 780225 780293 780207 781032 780224 780293 780294 780296 780227 780222 781060 780305 780297 781105 781032 781032 780239 780226 780226 781040 780304 780310 780205 7802.
780204 780243 780243 781043 780225 780225 780293 780207 781032 780224 780293 780294 780296 780227 780222 781060 780305 780297 781105 781032 781032 780239 780226 780226 781040 780304 780310 780205 7802.
16 Limited W ar ranty Megatech Product Support If you hav e questions about your model, or you’ re having a problem with your model simply call us at 1-201-662-2800. Our customer support team is av ailable from 10:30am to 4:30pm eastern standard time to answer your questions.
17 state to state. Megatech is not obligated to pro vide upgraded products at a reduced rate when a previous product’ s production cycle has ended. Me gatech reserves the right to modify warranty provisions without notice.
MT C7810 D ARK THUNDER NITRO POWERED HIGH SPEED DRAGSTER MT C7501 CHRIS CHIANELLI SIGNA TURE Q-SERIES COMPLETER P A CK FOR A UT O ST ART VEHICLES MT C7502 CHRIS CHIANELLI SIGNA TURE Q-SERIES COMPLETER.
MT C7501 CHRIS CHIANELLI SIGNA TURE Q-SERIES COMPLETER P A CK FOR A UT O ST ART VEHICLES MT C7502 CHRIS CHIANELLI SIGNA TURE Q-SERIES COMPLETER P A CK FOR PULL ST ART VEHICLES MT C7805 TEMPEST GLADIA .
www .me ga tec h.com Megatech International - 8300 T onnelle A venue North Bergen NJ 07047 - (201) 662-2800.
Een belangrijk punt na aankoop van elk apparaat MegaTech AfterBurner (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen MegaTech AfterBurner heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens MegaTech AfterBurner vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding MegaTech AfterBurner leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over MegaTech AfterBurner krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van MegaTech AfterBurner bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de MegaTech AfterBurner kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met MegaTech AfterBurner . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.