Gebruiksaanwijzing /service van het product KFN 14827 SDed van de fabrikant Miele
Ga naar pagina of 80
Operating and installation instructions Frost free fridge-freezer with PerfectFresh zone and ice cube maker KFN 14827 SDE ed To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time.
Guide to the appliance .............................................5 Caring for the environment ..........................................7 Warning and Safety instructions .....................................8 How to save energy ....................
Adjusting the interior fittings .......................................3 1 Moving the shelves ................................................3 1 Split shelf ........................................................3 1 Freezing and storing food .......
Installation ......................................................5 7 Location .........................................................5 7 Climate range ..................................................5 7 Ventilation ..............................
a On/Off sensor for the whole appliance and On/Off sensor for switching the PerfectFresh zone on and off separately b Super cool and Super freeze sensor c Sensor for setting a lower temperature ( X ) .
a Bottle rack b Adjustable shelf c Active charcoal filter holder d Control for setting the humidity in the PerfectFresh zone compartments e PerfectFresh zone compartments f Condensate channel and drai.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
This appliance complies with all relevant legal safety requirements. Improper use can, however, present a risk of both personal injury and material damage. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time.
Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Do not install and use a damaged appliance. A damaged appliance is dangerous. ~ If the connection cable is faulty it must only be replaced by a service technician authorised by the manufacturer to protect the user from danger.
~ The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations.
~ The ice cube maker is not suitable for connection to a hot water supply. ~ Before making plumbing connections, ensure the appliance is disconnected from the mains electricity supply.
~ Do not use defrosting sprays or de-icers, as they might contain substances which could damage the plastic parts or which could cause a build-up of gases and pose a danger to health. ~ Do not use any oils or grease on the door seals, as these will cause the seals to deteriorate and become porous with time.
Normal energy consumption Increased energy consumption Installation site In a ventilated room. In an enclosed, unventilated room. Protected from direct sunlight. In direct sunlight. Not situated near to a heat source (radiator, oven). Situated near to a heat source (radiator, oven).
Before using for the first time The stainless steel surface has a layer of protective foil to prevent scratching during transportation. ^ Do not remove this foil until the appliance has been installed or built in. ^ After removing the protective foil, treat external surfaces with a suitable stainless steel conditioning agent (available from www.
To switch between the PerfectFresh zone and freezer section touch the relevant sensor. If you want to select the freezer section (to check the temperature, for example), ^ touch the freezer sensor.
The freezer section remains switched on and the "Freezer" symbol is lit up. To switch the PerfectFresh zone back on again ^ Select the PerfectFresh zone. The "PerfectFresh" sensor lights up yellow, then touch the On/Off sensor until the temperature display lights up, or ^ Switch the appliance off and then back on again.
The door alarm is automatically disabled when the appliance is in the settings mode. As soon as the door is closed, the door alarm is activated again. Switching the sensor tones on/off The sensor tone which sounds each time a sensor is touched can be deactivated.
The old setting lights up, and your newly selected setting flashes. ^ Touch the On/Off sensor to confirm the new setting. ^ Touch the X sensor repeatedly until c appears in the display.
It is very important to set the correct temperature for storing food in the appliance. Micro-organisms will cause food which is not stored at the correct temperature to deteriorate rapidly. Temperature influences the growth rate of these micro-organisms.
– Each subsequent touch of a sensor: changes the setting incrementally. – Leaving a finger on the sensor: changes the setting continuously. Approx. 5 seconds after taking your finger off a sensor, the current setting of the PerfectFresh zone is automatically shown.
The temperature being set will flash in the display. The following information shows in the display when the sensors are touched: – Touching a sensor once: the last temperature selected flashes. – Each subsequent touch of a sensor: adjusts the temperature shown in 1 °C steps.
^ The temperature display brightness can now be changed by touching the X sensor: d0 : Maximum brightness d1 : Reduced brightness d –: Return to menu. The old setting lights up, and your newly selected setting flashes. ^ Touch the On/Off sensor to confirm the new setting.
Your appliance has been fitted with a warning system which ensures that the temperature in the appliance cannot rise unnoticed and to avoid energy being wasted if a door is left open. Activating the alarm system The alarm system is always active. It does not have to be switched on manually.
Door alarm The alarm will sound if a door is left open for more than approx. 2 minutes. The alarm off sensor will light up red and the symbol for the section which has the opened door will flash. The alarm will stop and the indicators will go out as soon as the door is closed.
Super cool The Super cool function can be used to rapidly reduce the temperature throughout the PerfectFresh zone to its lowest setting (depending on the room temperature). Switching on Super cool Super cool is particularly recommended for the faster chilling of large amounts of fresh food or drink.
Super freeze Switch the Super freeze function on before putting fresh food into the freezer section. This helps food to freeze quickly and retain its nutrients, vitamins, flavours and appearance. Super freeze is not necessary: – when placing food in the freezer that is already frozen.
For every type of food, there are ideal storage conditions to ensure it stays fresh as long as possible, retaining both flavour and vitamins. The important factors for this are the storage temperature and the humidity. The correct combination of temperature and humidity is a unique feature of the PerfectFresh zone.
Do not store explosive materials in the appliance or any products containing propellants (e.g. spray cans). Danger of explosion. If storing food which contains a lot of fat or oil, make sure that it does not come into contact with plastic components as this could cause stress cracks.
Please take into account that high humidity is only achieved and effective if the food is stored unwrapped or loosely wrapped . – The high humidity setting - is ideal for storing freshly harvested products such as vegetables, salad, herbs, mushrooms and home-grown seasonal fruit.
Unpacked meat and vegetables Different types of unpacked meats and vegetables must be kept separate. To avoid any microbiological cross-contamination, these foods may only be stored together if they are wrapped. Take food out of the PerfectFresh zone approx.
Moving the shelves The shelves can be adjusted according to the height of the food. ^ Raise the shelf, and pull it forwards slightly until the notch at the side is in line with the shelf support. It can then be raised or lowered to the required level.
PerfectFresh zone compartments The compartments in the PerfectFresh zone are on telescopic rails, and can be removed for filling, emptying or cleaning purposes. ^ Pull out the compartment as far as it will go, and then lift it up and out. Push the runners back in again to avoid injury or damage.
Maximum freezing capacity To ensure that fresh food placed in the freezer freezes through to the core as quickly as possible, the maximum freezing capacity must not be exceeded. The maximum freezing capacity for freezing within a 24-hour period is given on the data plate: "Freezing capacity .
Home freezing Only freeze fresh food which is in a good condition. Hints on home freezing – The following types of food are suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, dairy products, pastry, leftovers, egg yolks, egg whites and a range of pre-cooked meals.
Before placing food in the freezer section ^ When freezing more than 2 kg of fresh food, switch on the Super freeze function for some time before placing the food in the freezer (see "Super freeze"). This also helps to prevent food that is already in the freezer from starting to defrost.
Defrosting Frozen food can be defrosted in different ways: – in a microwave oven, – in an oven using the "Fan" or "Defrost" setting, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep the other food cold), – in a steam oven.
Cool pack The cool pack prevents the temperature in the freezer rising too quickly in the event of a power cut. Place the cool pack in the top drawer of the freezer section, directly on top of the food. The cool pack will be at its most effective after it has been in the freezer for approx.
For the automatic ice cube maker to operate it must be connected to the mains water supply. Switching on the ice cube maker ^ Switch on the freezer section. ^ Open the top left drawer a little. ^ Press the On/Off button on the ice cube maker. The indicator light will come on.
Switching off the ice cube maker The ice cube maker can be switched off independently of the freezer section if you do not want the appliance to make any ice cubes.
^ The length of the water intake time for the ice cube maker can now be adjusted by touching the X sensor: E1 : Shortest water intake time, E8 : Longest water intake time, E – : Return to menu. The old setting lights up, and your newly selected setting flashes.
PerfectFresh zone Condensate and frost can build up on the back wall of the PerfectFresh zone whilst in use. These are automatically removed and defrosted by the appliance. The condensate is drained away via a channel and drain hole into an evaporation system at the back of the appliance.
A range of Miele cleaning and conditioning agents is available from the Miele UK Spare Parts Department or via the internet at www.miele-shop.com. Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents.
Cleaning the ice cube tray The ice cubes are formed in a tray before they are dropped down into the drawer. This tray should be cleaned regularly to remove any stale ice or water. ^ Connect the appliance to the electricity supply. ^ Open the top left drawer a little.
Door seals Do not use any oils or grease on the door seals as these will cause the seal to deteriorate and become porous over time. The door seals should be cleaned regularly with clean water, and then wiped dry with a soft cloth.
The active charcoal filters should be changed approx. every 6 months. When the Change active charcoal filter indicator lights up red, the active charcoal filters need to be changed. To change the active charcoal filters ^ Pull the active charcoal filter holder upwards to remove it from the shelf.
If you have delayed changing the active charcoal filters and the indicator is not lit up, you will need to reset the counter when you replace the active charcoal filters via the settings mode. ^ Touch and leave your finger on the X sensor. ^ At the same time, briefly touch the On/Off sensor (without letting go of the X sensor).
Repairs to electrical appliances should only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.
. . . the frozen food is thawing because the freezer section is too warm. Is the room temperature lower than the ambient temperature for which the appliance is designed? ^ If so, raise the temperature of the room.
The warmest temperature will show in the display for about 1 minute. The display will then revert to showing the current temperature in the freezer. ..." dn " appears in the temperature display. The demonstration function is activated. ^ Call the Service Department.
. . . the floor of the PerfectFresh zone is wet. The condensate drain hole is blocked. ^ Clean the condensate channel and drain hole. If you still cannot remedy the fault having followed these suggestions, please contact the Miele Service Department.
Normal noises What causes them Brrrrr... Humming noise made by the motor (compressor). This noise can get louder for brief periods when the motor is switching on. Blubb, blubb.... A gurgling noise can be heard when coolant is circulating through the pipes.
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – your Miele Dealer or – Miele (see back cover for contact details). When contacting your Dealer or Miele, please quote the model and serial number of your appliance.
Notes on connecting to the mains water supply Connection to the mains water supply should only be carried out by a qualified and competent person in accordance with national and local regulations. The water quality must conform to the requirements for drinking water in the country the appliance is being installed in.
^ The stainless steel hose should be attached to the solenoid valve at the base of the appliance at the back. ^ Ensure that the hose is fitted correctly and that it is water tight. ^ Turn on the stopcock slowly and check the whole water system for leaks.
All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK). The appliance is supplied with a mains cable and moulded plug ready for connection to an a.
All electrical work should be carried out by a suitably qualified and competent person in accordance with local and national safety regulations. The appliance is supplied with a mains cable and moulded plug ready for connection to 220-240 V 50 Hz supply.
Do not place any appliance which gives off heat, such as a toaster or microwave oven, on top of this appliance, as this would increase the appliance's energy consumption. This appliance has side-wall heating and can be installed side-by-side with another refrigeration appliance.
Aligning the appliance ^ To align the appliance, adjust the feet using the spanner supplied. ^ If necessary, also align the two rear adjusting devices a using a socket wrench b . Turn the adjusting device clockwise to raise the appliance up at the back.
Appliance dimensions ABC KFN 14827 SDE ed 1850 mm 600 mm 630 mm Installation 59.
To avoid a build-up of condensation and resultant damage, refrigerators and freezers should not normally be installed side-by-side. However, this appliance has side wall heating, and can be installed side-by-side with certain other Miele appliances. Your dealer will be able to advise you on which models are suitable.
^ Close the doors to check whether the door handles are correctly aligned with one another. The top of both appliances must be the same height. If they are not, the covers will not fit properly. ^ Push the two appliances together, and align them again.
^ Position wide brackets j at the top and bottom on the back, and push the top bracket upwards until it is in the correct position (z). ^ Secure the brackets at the sides using hex screws k supplied. Do not drill holes for these screws in the appliance.
^ Push short trim m into the gap at the top of the appliances. Make sure that the gap in the trim faces the front. The trim must sit flush with the top of the appliances at the front. ^ Fit cover n in the space between the control panels. Make sure that the outer edges of the cover are flush with the control panels.
To change the door hinging you will need the following tools : – a cross-slotted screwdriver, – a flat-bladed screwdriver, – a selection of Torx screwdrivers, – a spanner. Two people are needed for changing the door hinging. Removing the door handles: ^ Pull door handle a towards you.
Removing the soft-close mechanism for the upper door: ^ Open the upper door. ^ Prise open a from the soft-close mechanism by inserting a flat-bladed screwdriver into the gap from above and easing it off bit by bit. Take care not to damage the door seal.
^ Slide soft-close mechanism bracket f as far as it will go towards the handle side of the door, and undo screws g on the soft-close mechanism. ^ Using a flat-bladed screwdriver, slide the soft-close door mechanism towards the handle side of the door, and lever it out at the side.
Caution. The upper door is not secure as soon as the upper hinge plate is removed. ^ Close the upper door. ^ Undo screws m in upper hinge plate n and pull it upwards and off.
^ Push hinge pin e up and out from underneath. The soft-close mechanism is now no longer fixed to the appliance. ^ Remove panel a . ^ Slide soft-close mechanism bracket f as far as it will go towards the handle side of the door, and undo screws g on the soft-close mechanism.
^ Remove cap l from the bush in the door and refit on the opposite side. Refitting the lower door: ^ Remove cover a by pulling it forwards. ^ Pull cover b off. ^ Screw foot c into hinge pin as far as it will go. ^ With the help of another person, carefully tilt the appliance backwards and pull hinge pin c out.
^ Fit hinge pin i into middle hinge plate k in the lower door. Replacing the lower soft-close door mechanism: ^ Remove cover a from panel b , rotate it by 180° and refit it on the other side. ^ Insert the soft-close mechanism back into the door, starting at the right hand side.
^ Attach panel b to soft-close mechanism bracket d . ^ Align bracket d to the hinge plate, and insert pin e from above so that the right angle fits into the recess. ^ Click cover f back into place. Make sure that cover f fits properly so that the door can be closed without hindrance and the pin is protected.
Replacing the upper soft-close door mechanism: ^ Remove cover a from panel b , rotate it by 180° and refit it on the other side. ^ Insert the soft-close mechanism back into the door, starting at the right hand side. ^ Slide the soft-close mechanism back into the door as far as it will go towards the appliance using a flat-headed screwdriver.
Make sure that cover e fits properly so that the door can be closed without hindrance and the pin is protected. ^ Remove retaining clip g . ^ Replace panel b onto the soft-close mechanism from above, clicking it back into place first at the bottom and then at the top.
Refitting the handle: Please make sure you follow the instructions below carefully when you refit the handle. The door seal will be damaged if the handle is fitted incorrectly. ^ Loosely attach the handle to the opposite side of the door with the two front screws b .
The appliance doors can be aligned with the housing after they have been fitted. In the following illustration the door is shown open to make it easier to see what you have to do. Align the lower door using the long outer slots in the lower hinge plate: ^ Remove centre screw a from the hinge plate.
a Top box b Appliance c Housing unit d Wall The appliance can be installed in a kitchen run. To match the height of the rest of the kitchen, the appliance can be fitted with a suitable top box a . A ventilation gap of at least 50 mm depth must be allowed for behind the appliance across the entire width of the top box for air to circulate.
77.
78.
79.
Alteration rights reserved / 5209 KFN 14827 SDE ed M.-Nr. 07 807 670 / 00.
Een belangrijk punt na aankoop van elk apparaat Miele KFN 14827 SDed (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Miele KFN 14827 SDed heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Miele KFN 14827 SDed vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Miele KFN 14827 SDed leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Miele KFN 14827 SDed krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Miele KFN 14827 SDed bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Miele KFN 14827 SDed kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Miele KFN 14827 SDed . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
