Gebruiksaanwijzing /service van het product KFN 14943 SDed van de fabrikant Miele
Ga naar pagina of 64
Operating and Installation Instructions Fridge-Freezer Combination KFN 14943 SD ed To prevent accidents and machine damage read these instructions before installation or use.
Description of the appliance .........................................4 Caring for the environment ..........................................6 Warning and Safety Instructions .....................................7 How to save energy ..................
Freezing and storing food ..........................................3 0 Maximum freezing capacity ..........................................3 0 Freezing fresh food ................................................3 0 Storing frozen food ...............
a ON button for the whole appliance and ON/OFF button for switching the refrigerator and freezer sections on and off individually b DynaCool button c Super Cool / Super Freeze button d Button to set t.
a Fan b Interior lighting c Butter and cheese compartment d Bottle shelf e Egg tray / serving shelf f Retainer for the Active AirClean filter g Shelves h Condensate channel and drain hole i Fruit and .
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc.
This appliance complies with all applicable safety laws and regulations. However, improper use can result in personal injury and material damage. Read the operating instructions carefully before operating the appliance for the first time. They contain important information on the installation, safety, operation and care of your appliance.
Technical safety ~ Before setting up the appliance, check it for any external damage. Do not install and use a damaged appliance. A damaged appliance may endanger your safety! ~ If the connection cable is damaged it must be replaced by a Miele approved service technician to protect the user from danger.
~ The electrical safety of this appliance can only be guaranteed if it is properly grounded in compliance with all applicable local and national safety regulations.
Correct use ~ Do not handle frozen items when your hands are wet. Your hands could freeze to the item(s). Risk of injury! ~ Never put ice or popsicles in your mouth immediately after taking them out of the freezer - your lips or tongue could freeze to the item(s).
~ Do not use defrosting sprays or de-icers. They may cause a build-up of potentially explosive gasses or contain substances that can damage the plastic or that could pose a danger to health. ~ Do not use any oils or grease on the door seals. They can cause the seals to deteriorate over time.
Normal energy consumption Increased energy consumption Installation site In a well ventilated room. In an enclosed, poorly ventilated room. Protected from direct sunlight. In direct sunlight. Away from heat sources (radiator, stove/oven). Near heat sources (radiator, stove/oven).
Before first use The stainless steel surfaces on the inside and outside of the appliance are covered with protective sheeting. ^ Do not remove the protective sheeting until the appliance has been installed in its final location.
Use this button to switch back and forth between the refrigerator section and the freezer section. If you want to select the freezer section (e. g. to check the temperature), ^ tap the button to switch from the refrigerator section to the freezer section; the Freezer symbol will light up yellow.
That section is now switched off, while the other section remains on. To switch a section back on again, ^ select the section you wish to switch on; the corresponding symbol lights up yellow. ^ Touch the ON/OFF button until the temperature display lights up, or ^ switch the appliance off and then back on again.
Turning the button sound on and off If you prefer the buttons to be silent when touched, you can turn the button sound off. ^ Touch the X button and keep your finger on the button. ^ Now tap the ON/OFF button once (WITHOUT releasing the X button!). ^ Keep your finger on the X button for another 5 seconds until c is displayed.
^ Whenever you finish changing a setting, tap the ON/OFF button to confirm. ^ Keep tapping the X button until c is displayed. ^ Tap the ON/OFF button. You have left the settings mode. When the safety lock is activated, the safety lock indicator X will light up show in the temperature display.
The correct temperature is very important for storing food. If food is not stored at the correct temperature, bacteria can multiply rapidly, causing the food to spoil. This can be prevented or slowed down by selecting the correct temperature. Temperature affects the rate at which bacteria can multiply.
Setting the temperature The temperatures for the refrigerator section and the freezer section are set separately. ^ Select the refrigerator or the freezer section. The Refrigerator or Freezer symbol lights up yellow. ^ Set the temperature with the buttons beside the display.
Changing the brightness of the temperature display You can adjust the brightness of the temperature display to suit the lighting conditions of the room. ^ Touch the X button and keep your finger on the button. ^ Now tap once on the ON/OFF button (WITHOUT releasing the X button!).
The appliance is equipped with an alarm system to ensure that the temperature in the freezer section does not rise unnoticed and to avoid energy being wasted if the door is left open. Switching the alarm system ON The alarm system is always active. It does not need to be switched on manually.
Door alarm If one of the appliance doors is left open for longer than approx. 2 minutes, the alarm signal will sound. The alarm off button lights up red and the symbol of the temperature section with the open door flashes. Once the appliance door is shut, the alarm stops and the displays go out.
Super Cool The Super Cool function can be used to rapidly reduce the temperature in the refrigerator section to its lowest setting (depends on the room temperature). Switching Super Cool ON Super Cool is particularly recommended for the fast chilling of large amounts of fresh food or drinks.
Super Freeze For best results, switch on the Super Freeze function before putting fresh food into the freezer. Fresh food will be frozen quickly, so that the nutritional value, vitamins, appearance and taste are maintained. Exceptions: – if you are loading frozen food into the freezer.
DynaCool If the dynamic cooling function (DynaCool) is not switched on, the natural circulation of air in the appliance can create different temperature zones in the refrigerator as the cold, heavy air will sink to the lowest section of the appliance.
Different storage zones Due to the natural circulation of air in the appliance, there are different temperature zones in the refrigerator. Cold, heavy air sinks to the lowest section of the appliance. Make use of these different zones when placing food in the appliance.
Moving the shelves The shelves in the refrigerator section can be adjusted according to the height of the food. ^ Lift the shelf, pull it forwards slightly, lift the recess over the support ribs and move the shelf up or down. The edge of shelf's rear stop must face upwards so that food does not touch the rear wall and freeze to it.
Moving the serving shelf / bottle shelf ^ Lift the hanging container up and out of the stainless steel support frame. ^ Push the stainless steel support frame up and remove it by pulling it forward. ^ Replace the stainless steel support frame at the desired location.
Adjusting the bottle divider (may vary by model) The bottle divider can be moved to the left or right. This holds the bottles more securely in position when the door is opened and closed. The bottle divider can be removed completely (e.g. for cleaning): ^ Slide the front edge of the bottle divider up and lift the bottle divider out.
Maximum freezing capacity To ensure that fresh food placed in the freezer freezes through to the core as quickly as possible, the maximum freezing capacity must not be exceeded. The maximum freezing capacity within a 24-hour period is listed on the data plate, as "Freezing capacity .
Home freezing Only freeze food that is fresh and in good condition! Hints for home freezing – The following types of food are suitable for home freezing: fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, dairy products, baked goods, leftovers, egg yolks, egg whites and most pre-cooked meals.
Before placing food in the freezer ^ When freezing more than 2 kg of fresh food, switch on the Super Freeze function ahead of time (see Super Freeze). This will protect the food that is already in the freezer with an added boost of cold. Placing food in the freezer Food to be frozen can be placed anywhere in the freezer section.
Defrosting frozen foods Frozen food can be defrosted in various ways: – in the microwave, – in a regular oven, using the "fan" or "defrost" setting, – at room temperature, – in the refrigerator (as it thaws, the frozen food will help cool the other food in the refrigerator), – in a steam oven.
Using the cool pack The cool pack prevents the temperature in the freezer from rising too quickly in the event of a power outage. Place the cool pack in the upper drawer, directly on top of the food. The cool pack will be at its most effective after it has been in the freezer for approximately 24 hours.
Refrigerator section The refrigerator defrosts automatically. During normal operation, condensate and frost can build up on the rear wall of the refrigerator and drawers. You do not need to remove this, as it will defrost and evaporate automatically with the heat generated by the appliance.
Never use abrasive cleaners on the appliance, or products that contain washing soda, acids, chlorine bleach or chemical solvents. Note that so-called non-abrasive cleaners are also unsuitable as they can cause dull patches. For all stainless steel surfaces, use a suitable stainless steel cleaner (available through Miele Customer Service).
Cleaning the ventilation slits ^ The ventilation slits should be cleaned on a regular basis with a brush or vacuum cleaner. A build-up of dust will increase the amount of energy the appliance consumes. Door seal Do not use any grease or oil on the door seal as they will cause the seal to deteriorate over time.
The prompt to change the active charcoal filter will occur approx. every 6 months. When the display for an active charcoal filter change lights up red, the active charcoal filters must be changed. Replacing the active charcoal filters ^ Pull the retainer for the active charcoal filters up and off the shelf.
If you changed the active charcoal filters at a later date and the active charcoal filter change display is off, the timer must be reset via the settings mode: ^ Touch the X button and keep your finger on the button. ^ Now tap once on the ON/OFF button (WITHOUT releasing the X button!).
Repairs to electrical appliances must be carried out by qualified professionals. Work performed by unqualified persons can place the user at considerable risk of harm. What should I do i f... . . . the refrigerator or freezer section does not cool? ^ Check that the respective section is switched on.
. . . the frozen food thaws because it is too warm in the freezer section? ^ Did the room temperature drop below that for which the appliance was designed? Increase the room temperature. The compressor will run less often if the room temperature is too low.
..." dn " appears in the temperature display? The demo mode is activated. ^ Call Customer Service. . . . the appliance cannot be switched off? The safety lock is activated.
Normal noises What causes them? Brrrrr... Humming noise made by the motor (compressor). This noise may get louder for brief periods, whenever the motor kicks in. Blubb, blubb.... A gurgling noise can be heard when coolant is circulating through the pipes.
In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service Department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
, Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
Do not place any devices that produce heat (such as a toaster or microwave) on top of the appliance. This would increase the energy consumption of the appliance! This fridge/freezer should not be placed side-by-side with a second model.
Adjustments ^ Use the wrench provided to adjust the feet as needed, so that the appliance is level. ^ If necessary, unscrew the foot a from the hinge bracket in order to support the appliance door.
Appliance dimensions ABC KFN 14943 SD ed 2020 750 630 Installation information 48.
The appliance comes with right-hand hinging. If left-hand door hinging is preferred, then follow these instructions to change the door hinge: You will need the following tools: – a crosstip screwdriver, – a flathead screwdriver, – various sizes of Torx screwdrivers, – a fork wrench.
Before changing the hinging, remove any items of food from the shelves in the appliance door. Removing the top soft-close mechanism: ^ Open the top door of the appliance. ^ Loosen the panel a from the soft-close mechanism: From below, slide a flathead screwdriver into the recesses, then slowly and carefully lift off the panel.
^ Remove the cover d . Now the soft-close mechanism and the appliance are no longer connected. ^ Remove the panel a . ^ Push the shock absorber arm f as far as possible towards the handle side. ^ Loosen the three screws g on the soft-close mechanism and the spacer.
Caution! The top door of the appliance is no longer secured as soon as the hinge bracket is removed when following the instructions below! ^ Close the top door of the appliance. ^ Loosen the screws m on the top hinge bracket n and remove the hinge bracket by pulling up.
^ Push the pin e up and out. Now the soft-close mechanism and the appliance are no longer connected. ^ Remove the panel a . ^ Push the shock absorber arm f as far as possible towards the handle side. ^ Loosen the three screws g on the soft-close mechanism and the spacer.
^ Lift the plugs l out of the door bearing bushing in the appliance door and place it on the other side. Mounting the bottom door of the appliance: ^ Remove the cover a towards the front. ^ Pull the cover b off. ^ Screw the adjustment foot at the bearing pin c completely in.
^ Put the bearing pin i in the middle of the appliance through the hinge bracket k into the bottom door of the appliance. Mounting the bottom soft-close mechanism: ^ Remove the cover a from the panel b , turn it 180° and replace it on the other side.
^ Hang the panel b on the shock absorber arm d . ^ Pull the shock absorber arm d towards the hinge bracket and insert the pin e from the top so that the square rests in the recess. ^ Put on the cover f in such a way that it engages. Take care that the cover f sits correctly to ensure that the door closes properly and the pin is secured.
Mounting the top soft-close mechanism: ^ Remove the cover a from the panel b , turn it 180° and replace it on the other side. ^ Hook the spacer on the handle side into the retainer (A). ^ Hook the soft-close mechanism into the retainer (B) on the appliance side.
^ Remove the securing device g . ^ Place the panel b onto the soft-close mechanism from above, engaging it at the bottom first and then at the top. ^ Close the top door of the appliance. Remounting the door handles: The following instructions must be followed when attaching the door handle, otherwise the door seal could be damaged.
The appliance doors can be aligned with the appliance housing afterwards. In the following figure, the appliance door is not closed so that the individual steps can be seen more clearly. Align the bottom door in the bottom hinge bracket via the outer, elongated holes: ^ Remove the middle screw a from the hinge bracket.
a adapter cabinet b appliance c kitchen cabinet d wall The appliance can be installed in any fitted kitchen. To match the appliance to the height of the fitted kitchen, a suitable adapter cabinet a can be installed over the appliance. A ventilation gap of at least 2 inches (50 mm) must be provided between the adapter cabinet and the kitchen wall.
61.
62.
63.
Subject to change without notice / 4709 KFN 14943 SD ed M.-Nr. 07 589 450 / 01.
Een belangrijk punt na aankoop van elk apparaat Miele KFN 14943 SDed (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Miele KFN 14943 SDed heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Miele KFN 14943 SDed vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Miele KFN 14943 SDed leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Miele KFN 14943 SDed krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Miele KFN 14943 SDed bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Miele KFN 14943 SDed kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Miele KFN 14943 SDed . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
