Gebruiksaanwijzing /service van het product T 4123 van de fabrikant Miele
Ga naar pagina of 44
Operating instructions f or v ented tumb le dr y er T 4123 T o avoid the risk of accidents or damage to the machine it is essential to read these Operating instructions before it is installed or used for the first time.
W arning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Caring for the en vironment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Disposal of the packing material .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Installation site .
T o avoid the risk of accidents and damage to the machine please read these instructions carefully befor e using it for the first time. They contain important infor mation on its safety , use and maintenance. Keep these operating instructions in a safe place and ensure that new users are familiar with the content.
If the connection cable is faulty it must only be replaced by a Miele approved service technician to pr otect the user from danger . In the event of a fault or for cleaning purposes, the machine is on.
Always close the door after use. This way you will avoid the danger of: – children climbing onto or into the dryer or hiding things in it. – pets or other small animals climbing into it. Do not let anyone sit or lean on the door , as this can cause the machine to tip up.
Disposal of the packing material The transport and protective packing has been selected from materials which are envir onmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
a Programme selector The programme selector can be turned clockwise or anti-clockwise. b Programme sequence and c heck lamps c Start button Press the Start button to start a programme. The Start indicator lamp will flash as soon as a programme can be started.
W ash care labels Before drying check the drying symbol on the wash care label. Significance of symbols: q Dry at nor mal temperature r Dry at low temperature s Do not tumble dry If no symbol is featu.
Programmes Fabric type Special notes CO TTONS Drying levels maximum load: 5 kg (1) Normal+ Single and multi-layered fabrics, e.g. mixed load of cotton fabrics (e.g. towelling, jerseywear). - Normal (2) Load of similar cotton fabrics (jersey wear , flannelette sheets, towelling).
Programmes Fabric type Special notes MINIMUM IRON Drying levels maximum load: 2.5 kg (1) Normal+ Minimum iron items which are made of synthetic or blended fabrics (e.g. pullovers, dresses, tr ousers) which are not dried adequately in the Normal programme.
Programme Fabric type Special notes Special care programmes W oollens hand care maximum load: 2 kg (1) Woollen fabrics T o refr esh and fluff up woollen garments quickly . Remove garments immediately at the end of the programme. Do not r epeat. Woollen fabrics ar e not dried completely by this programme.
A Prepare the laundry ^ As far as possible, sort laundr y for: - the type of fibre or weave, - the degree of dryness requir ed, - similar size of items, - the moisture content after spinning. This will help towards achieving an even drying result. Fasten duvet covers etc.
C Select a programme ^ T ur n the programme selector to the requir ed programme. See "Consumption data" chart for programme durations. Low temperature ^ For drying par ticularly delicate fabrics (care symbol r ) e.g. acrylics turn the programme selector to the Low temperature position.
Selecting a different pr ogramme As long as the cooling down phase or the anti-crease phase has not been reached it is possible to change a programme after it has started by turning the programme selector to a differ ent programme position. Interrupting a programme ^ Switch the machine off with the I-On / 0-Off button.
Cleaning the fluff filter The fluff which is cr eated by the drying process is collected in the fluff filter in the door . Clean the filter after every drying cycle. ^ Open the door and pull the fluff filter out of the door as illustrated. ^ Use your fingers to remove the fluf f from the surface of the filter .
T umble dryer Disconnect the machine from the power supply . ^ Clean the housing and control panel with a mild cleaning agent or soapy water . Clean the drum and other stainless steel parts with a suitable proprietary stainless steel cleaner following the manufacturer’s instructions.
With the help of the following notes minor faults in the perfor mance of the machine, some of which may result fr om incorrect operation, can be put right without contacting the Service Department.
Prob lem P ossible cause Remedy There is a build up of fluff. Fluff is principally the result of friction when garments are being worn and washed. Machine drying hardly causes any fluff to form and, has been established by resear ch institutes, to have no effect on the lifetime of fabric.
Prob lem P ossible cause Remedy The drying process goes on too long or even switc hes off. Important : Before attempting to remedy one of the following causes, switch the dryer off and switch on again to start the programme again. V entilation to the dr yer is insufficient (e.
Prob lem P ossible cause Remedy The programme has stopped. The Anti-crease/Finish lamp has come on in the sequence display and the buzzer is sounding. This is not a fault. The electronic unit has recognised that ther e is no laundry in the drum and cancelled the programme.
T o change the interior drum lamp ^ Open the door . Before changing the lamp, disconnect the machine from the mains power supply . Y ou will find the interior lamp cover at the top of the drum aperture. ^ Insert the opener under the side edge of the cover as illustrated.
After sales service Repairs In the event of any faults which you cannot remedy yourself, please contact – your Miele Dealer or – The Miele Service Department (see back cover for address).
Front vie w a V enting connection: rear , right or left (supplied with the rear socket open) b Supply cable for electrical connection c Control panel d Door e Four height-adjustable screw feet Install.
Installation site , Make sure the dryer door can be opened without hindrance after installation. T ransporting the machine to its installation site When moving the machine you can hold it by the lid where it pr otrudes to the rear of the dryer .
Aligning the machine The machine must be perfectly level to ensure safe and pr oper operation. ^ The screw feet can be adjusted to compensate for any unevenness in the floor . , A ventilation gap of 10 mm must be maintained between the base of the machine and the floor .
Electrical connection U .K. All electrical work should be carried out only by a suitably qualified and competent person, in strict accordance with national and local safety regulations. Ensure power is not supplied to the machine while installation work is being carried out.
If the colours of the wires in the mains lead of this machine do not correspond with the coloured markings identifying the terminals of your plug, proceed as follows: ^ The wire which is colour ed gre.
General Important Before operating the tumble dryer , a suitable ducting system must be installed to carry the moist air from the dryer to the outside. This can be: . . . . . . flexible ducting hose, or plastic piping connected to the dryer , or . . .
Calculating the effective duct length: Friction against the inner walls of the ducting will slow down the expelled air as it passes through. An elbow , bend, non-return flap or wall vent creates more friction than a straight duct. The friction created by each of these is expressed as an ad ditional duct length factor .
3. Example A W all pipe, with louvred vent = 1 x 3.8 m Additional duct length = 3.8 m B/D 2 Elbows, 90° = 2 x 0.8 m Additional duct length = 1.6 m C 0.5 m plastic piping = 0.5 x 1 m Additional duct length = 0.5 m E Side connection, left = 1 m Additional duct length = 1.
V enting systems overview The various venting systems which are possible ( a b c ) are described on the following pages. Adapter A ring adapter ** (1) is installed in adapter (2) for the installation of a flexible vent duct.
Installation examples - venting system with flexib le ducting Window vent 1. Window vent kit (fitted in a "plexiglass" pane) (separate fitting instructions are supplied with the Miele window vent kit) 2. Adapter for flexible hose Connection to an exhaust flue 1.
b V enting system with plastic piping Plastic piping is a good option where the vented air has to ducted for some distance. The smooth walls of the pipe are less r esistant to the vented air than the walls of a flexible vent hose, for example. Time and energy consumption are better with plastic piping.
c Connecting directly to a wall vent The best method of venting the dryer is to connect it directly to the outside wall of a room. However , it is necessary to inser t the wall vent right through the wall.
W asher dr yer stac k Height of venting outlet for washer dryer stack Miele washing machine with straight or sloping fascia Stacking kit* without worktop: A = 94.
Programmes Capacity Final spin speed (in a domestic washing machine) Electricity consumption Drying time (incl. cooling down time) kg rpm kWh Minutes CO TT ONS Normal+ 5.0 1200 1400 1600 1800 2.70 2.60 2.30 2.25 70 67 60 59 Normal (1) 5.0 800 (70 % residual moisture) 3.
Height 85 cm (adjustable +0.7/-0.7 cm) Height without lid 82 cm Depth with door open 106 cm Width 59.5 cm Depth 58 cm Weight 48 kg Drum volume 100 litres Maximum capacity 5 kg dry weight Length of connection cable 1.
Progr ammable functions f or changing standard settings 39.
Increased drying level in the CO TT ONS programmes The machine is designed to dry using as little energy as possible. However , if you require the laundry to be drier , it is possible to reduce the final moisture level in the COTTONS programmes. Note that pr ogramme durations will be longer if this option is activated.
Increased drying level in the MINIMUM IRON pr ogrammes The machine is designed to dry using as little energy as possible. However , if you require the laundry to be drier , it is possible to reduce the final moisture level in the MINIMUM IRON programmes.
Buzzer An audible tone sounds repeatedly at the end of a programme. The buzzer is activated as standard ex-works. It can be deactivated if wished. The buzzer will sound if there is a fault, even if it has been deactivated. Follow steps A to G to programme and store in memory .
43.
M.-Nr . 06 067 720 / 00 Alteration rights reserved/0504 This paper consists of cellulose which has been bleached without the use of chlorine..
Een belangrijk punt na aankoop van elk apparaat Miele T 4123 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Miele T 4123 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Miele T 4123 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Miele T 4123 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Miele T 4123 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Miele T 4123 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Miele T 4123 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Miele T 4123 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
