Gebruiksaanwijzing /service van het product T 8422 C van de fabrikant Miele
Ga naar pagina of 52
Operating instructions for condenser tumble dryer T 8422 C T o av oid the risk of accidents or damage to the appliance it is essential to r ead these instructions bef ore it is inst alled and used for the f irst time .
Disposal of the packing material The tr ansport and protectiv e packing has been selected fr om materials whic h are en vironment ally friendl y for disposal and can normally be rec ycled. Ensure that an y plastic wr appings , bags etc. are disposed of saf ely and kept out of the reac h of babies and young childr en.
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operating the tumble dryer . .
After Sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 F uture updates (PC) ................................................3 4 Appliance guar antee ......................................
~ It is essential to r ead these instructions . This tumble dryer conf orms to current saf ety requirements . Inappropriat e use can, ho wever , lead to per sonal injury and damage to property . T o av oid the risk of accidents and damage to the tumble dryer , please read these instru ctions carefull y befor e using it for the f irst time .
Technical safety ~ Befor e set ting up the tumble dr yer , chec k it for an y e xternally visible damage. Do not install or use a damaged tumble dryer . ~ Befor e connecting the tumble dryer , ensure that the connection dat a on the data plat e (voltage and connect ed load) match the mains electricity supply .
Correct use ~ T o pre vent the risk of f ire, the follo wing te xtiles must not be dried in this tumble dryer: – items whic h hav e not been washed. – items , such as w orkwear , which hav e not been thoroughl y cleaned and which ar e still soiled with grease , oil or other desposits (suc h as cosmetics , lotions etc).
~ The dryer must not be used without the fluf f filt ers in place or if the fluf f filt ers are damaged in an y w ay . ~ The f luff filt ers must be cleaned regularl y . ~ The dryer must not be used without the condenser unit in place. ~ The f luff filt ers must be thor oughly dried af ter cleaning.
Control panel a Low temperature button Delicate f abrics are dried at a low er temper ature . b Drying level button with indicator lights c Display d Delay start button This but ton is used f or: - Se.
Display The f ollowing ar e selected via the display: – Delay st art – Dur ation of the Cool air and W ar m air progr ammes – P rogr ammable fu nctions The displa y also shows: – P rogr amme d.
Care symbols Befor e drying check the drying symbol on the care label. If there ar e no symbols , dr y at your o wn risk! q .........D r ya tn o r m a lt emper atur e r .
Brief instructions The headings number ed ( A , B , C ...) show the oper ating sequence and can be used as a brief guide to using y our dryer . A Sort the laundry T o ensure an e ven drying result separ ate out the w ashed laundr y and sort it according to: .
D Select a programme ^ Select the progr amme you w ant. The indicat or lamp for the progr amme selected will light up . A drying level or e xtr a option indicator light may also light up , and the dur ation may also be displa yed.
F Start the programme The Star t/Stop but ton will f lash when a progr amme is being selected. The flashing indicat es that a progr amme can be started. ^ P ress the Start/Stop but ton. The Star t/Stop but ton will no w light up constantl y . Drying will appear in the display and the time remaining will st art cou nting down.
Low temperature F or all delicate or minimum iron f abrics with the r symbol on the car e label (e.g . acrylic garments). – The pr ogramme dur ation is longer . – On some progr ammes Low temper ature is a standar d part of the progr amme and so cannot be deselected.
Cottons Max. load: 6 kg* Extra dry, Normal** F abric type Single and multi-lay ered cot ton f abrics such as t ow elling, jerse ywear , T -shir ts , underwear . Notes – Select Extr a dr y for multi-la yer ed and very thick f abrics . – Do not use Extr a dry for jerse y f abrics (e .
Woollens handcare Max. load: 2 kg* F abric type W oollen fabrics Note – T his progr amme only f luffs up w oollen garments . – F abrics ar e not completel y dried in this progr amme. Remo ve g ar ments as soon as the progr amme has finished and leav e to f inish dr ying at room t emper ature .
Automatic Max. load: 3.5 kg* Normal, Hand iron F abric type Mix ed loads of garments suitable for the Cot tons and Minimum iron pr ogr ammes . Sor t according t o colour .
Once a programme has started - changing the programme Y ou cannot change t o another progr amme once a progr amme has started (this pr ev ents unintentional alter ations). Y ou will need to cancel the curr ent progr amme before y ou can select a new one .
The s ystem loc k pre vents the dryer being used without your kno wledge . It can be activ ated if wished. The dryer's electr onics are then loc ked.
Emptying the condensed water container The condensed w ater will be collect ed in the condensed w ater container unless the appliance has been fit ted with a dr ain hose (see "Installation"). Empty the condensed wat er container af ter ev er y drying progr amme.
Cleaning the fluff filters The f luff which is cr eated b y the drying process is collect ed by the f luff filt ers in the door and the door opening. Clean the filt ers af ter each drying progr amme*. Cleaning them whilst dry Tip: Y ou can also use a v acuum cleaner to r emov e the fluff .
Cleaning them with water If there is a gr eat deal of compacted fluf f on any of the f ilter s , they can be remo ved and cleaned under hot running wat er . ^ Open the door and pull the fluf f filt er out of the door as described pre viously . The two filt ers in the door opening can also be remo ved if y ou need to clean them with w ater .
Cleaning the tumble dryer Disconnect the tumble dryer from the mains electricity supply . Miele br anded cleaning and conditioning produ cts are a vailable t o order fr om your Dealer , the Miele Spare P ar ts Department or via the internet on www .miele-shop.
Cleaning the condenser unit Deter gent residue , hair and fine fluf f from the dryer can get thr ough the fluf f filt ers and bloc k the condenser u nit. Dust fr om the room in whic h the dr yer is installed can also get int o the condenser unit and cause a blockage .
^ P ull the condenser u nit out of its housing by the handle . Checking the condenser unit ^ Hold the condenser unit up to the light as shown . ^ Check t o see if there is an y fluf f inside it. The arr ows in the illustr ation abov e indicate wher e to look.
^ Then f lush the u nit through fr om the front. ^ Check the condenser unit again f or any visible f luff and if necessary flush it through ag ain until it has all gone. ^ Remo ve an y soiling still visible inside the housing unit by hand using a damp cloth.
With the help of the f ollowing not es , minor f aults in the performance of the appliance, some of which ma y result fr om incorrect oper ation, can be put right without contacting the Service Department.
Problem Possible cause Remedy The Clean out airways indicator light comes on. This indicat or light comes on to w arn you that the dryer is not working ef ficientl y . P ossible cause: T he fluff filt ers ar e clogged with fluff or with deter gent residues .
Other problems Problem Possible cause Remedy The drying process goes on too long or even switches off. In some circumstances, the Clean out airways indicator light still comes on, even though the filters are clean. Please check all the possible causes and switch the dryer off and then back on again.
Problem Possible cause Remedy Water leaks from the dryer after the condenser unit has been cleaned. – The inner co ver of the condenser unit has not been lock ed properl y and/or the condenser unit has not been positioned correctl y . – Fluff has collect ed in the condenser unit housing.
Problem Possible cause Remedy The tumble dryer fails to start when switched on. No obvious cause . – Is the dryer switc hed on? – Is the plug correctl y inserted into the soc ket and switc hed on? – Is the door closed properl y? – Has the fuse or circuit break er tripped? The interior drum lighting does not come on.
Changing the lamp Disconnect the tumble dryer from the mains electricity supply . ^ Open the door . Y ou will find the int erior lamp cov er at the top of the drum aperture . ^ Insert a suitable tool, such as a wide bladed scre wdriv er , u nder the side edge of the lamp cov er as illustr ated.
In the ev ent of any f aults which you cannot remedy y ourself , please contact – your Miele dealer or – the Miele Service Department (see back co ver f or contact det ails).
Front view a Mains connection cable b Condensed w ater container c Contr ol panel d Door e Service panel for condenser unit f F our height-adjustable scre w feet g External dr ainage options (e .g. via w ash basin, w ash basin dr ain outlet, or gully).
Rear view a P rotruding lid f or holding when moving the appliance (see arr ows) b Air inlet vent f or cooling the condenser unit c Mains connection cable d External dr ainage of the condensed wa t e .
Levelling the tumble dryer The appliance must be perfectl y level t o ensure saf e and proper oper ation. ^ The scr ew feet can be adjust ed to compensate f or any unev enness in the floor .
External condensed water outlet General notes When drying is in progr ess , condensed w ater is pumped into the condensed w ater container through the dr ain hose at the back of the dryer . The condensed w ater can also be dr ained off dir ectly if the tumble dryer is installed near a sink, dr ain outlet etc.
External drainage via a sink or gully ^ See "F ront vie w" illustr ation. , If you w ant to dr ain the wat er off into a sink y ou will need to secur e the hose carefull y , e .g. by tying it to a tap t o make sur e it cannot slip during use.
1 Adapt er 2 Nut 3 Hose clip 4 End of the hose 5 Non-return v alve 6 T umble dryer drain hose ^ Fit adapt er 1 to the sink dr ain outlet using nut 2 . If this nut has a flat disc in it y ou should tak e the disc out fir st. ^ At tach the end of the hose 4 to adapter 1 .
Electrical connection U.K. All electrical work should be carried out by a suit ably qualif ied and competent person, in strict accordance with current national and local saf ety regulations (BS 7 671 in the UK). Ensure po wer is not supplied t o the appliance until aft er installation work has been carried out.
Programme Load Final spin speed in a domestic washing machine Energy Duration kg* rpm kWh Minut es Cottons Normal 6.0 1 000 (60 % residual moisture)** 1 200 1 400 1 600 1 800 3.30 3.00 2.85 2.55 2.50 89 81 78 70 69 Cottons Hand iron 6.0 1 000 (60 % residual moisture)** 1 200 1 400 1 600 1 800 2.
Height 850 mm Height for building under 820 mm Width 595 mm Depth 580 mm Depth with door open 1 060 mm Suitable for pushing under a workt op Y es Suitable for st acking Y es W eight 51 kg Drum volume 1 1 1 litr es Maximum capacity 6 kg dry weight Capacity of condensed w ater container appro x.
Programmable functions for changing default settings The pr ogrammable functions are used to alt er the tumble dryer´s electronics t o suit changing requir ements .
Extending the range of the drying levels Y ou can e xtend the r ange of the drying levels f or many of the progr ammes: Machine iron+ (drier than Machine ir on). Hand iron+ (drier than Hand iron). Normal+ (drier than Normal). In addition the Extr a dry dr ying lev el can be made av ailable for the Delicates and Denim pr ogr ammes .
Altering the volume of the buzzer The buzz er has t wo volumes . Normal The buzz er sou nds at the end of a progr amme (default set ting). Loud The buzz er sou nds at maximum volume at the end of a progr amme. Follow steps A to F to programme and store in memory.
Memory function The electr onics will memorise any e xtra options select ed for a progr amme. The dur ation selected for the timed drying progr ammes will also be stor ed in memory . These set tings will be selected automaticall y the ne xt time the progr amme is chosen.
Extending the cooling down time The cooling do wn phase which takes place befor e the end of a progr amme can be lengthened if requir ed. This makes the g arments easier to handle . The cooling do wn time – can be e xtended by 5 minut es or 1 0 minutes .
Clean out airways indicator Fluff should be r emov ed aft er drying. The Clean out airwa ys indicat or will remind y ou to clean the f ilters when a certain amount of fluff has collect ed in the filt ers . Y ou can decide at what lev el of fluf f this reminder should be given.
Keypad tone An audible t one sounds each time a but ton is pressed. Follow steps A to F to programme and store in memory. Befor e you begin, fir st ensure that : – The tumble dryer is s witched of f. – The door is closed. A P ress the Start/Stop but ton and k eep it pressed in whilst carrying out steps B - C .
Adjusting the dryer's electronics for very soft water , Extremel y sof t wat er can affect the sensitivity of the control electronics . If the dr yer is installed in an area with v ery sof t w ater , y ou should contact y our local w ater supplier for information and advice reg arding w ater har dness and w ater conductivity .
M.-Nr . 07 1 27 590 / 02 Alter ation rights reserved/2008.
Een belangrijk punt na aankoop van elk apparaat Miele T 8422 C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Miele T 8422 C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Miele T 8422 C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Miele T 8422 C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Miele T 8422 C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Miele T 8422 C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Miele T 8422 C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Miele T 8422 C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
