Gebruiksaanwijzing /service van het product C6/C64 van de fabrikant Mitsubishi Electronics
Ga naar pagina of 173
CNC C6/C64 CONNECTION AND MAINTENANCE MANUAL BNP-B2255E(ENG).
MELDAS and MELSEC are registered tradem ar ks of Mitsubi shi Electric Corporation. Other brands and product names thro ughout this manual are trademarks or regi stered trademarks of their respective holders.
Introduction This manual is called MELDAS C6/C64 CONNECTION AND MAINTENANCE MANUAL an d covers the items related to installation, connection and maintenance of this NC unit. Read this manual thoroughly before usi ng. For safe use, fully understand "Precautions for Safety" on the next page first.
Precautions for Safety Always read this manual and enclosed documents before installation, operation, maintenance and inspection to ensure corre ct usage. Thoroughly under stand the basics, safety information and precautions of the devices before using.
For Safe Use This product is not designed or manufactured on the assumption that the product will be used for the equipment or systems that are to be subject to any fatal consequences. Please inquire our customer service department about any particular usage other than the normal usage as a machine tool.
2. Items related to prevention of fire CAUTION Install the controlle r , servo drive unit, servomot or and regenerati ve resistor on non-combustible material. Installation di re ctly on or near combustible materials could result in fires. If any malfunction in the unit is observed, sh ut off the power at the unit’ s input power side.
4. General Precautions Always follow the precautions below. Incorrect handling could result in faults, injuries or electric shocks, etc. (1) Transportation and installation CAUTION Correctly transport the product s according to the weights. Use servomotor ’s suspe nsion bolts to transport the se rvomoto r itself.
CAUTION T ake care not to cut hands, etc. with the heat radiating fins or metal edge s. Do not block the intake/outt ake ports of the servomotor with the cooling fan. Install the controlle r ’s display unit and ope ration bo ard unit on the spot wh ere cutting oil will not reach.
(2) Items related to wiring CAUTION Correctly wire this product. Failu re to observe this could result in servomotor runa way , etc. Do not install a phase advancin g capacitor , surge ab sorber or radio noise filter on the output side of the servo drive unit.
CAUTION Separate the sign al wire from the drive line or power li ne wh en wiring. Use wires and cables whose wire di ameter , heat resistan ce level and bending cap acity are compatible wi th the system. Ground the device according to the req uirem ents of the country where t he devi ce is to be used.
CAUTION Do not alter . Use a noise filter , etc. to redu ce the ef fect of electromagnet ic disturbances. Electromagneti c disturbances could adve rsely af fect the elec tronic devices used near the servo drive unit. Use the servo drive unit, servomotor and each regenerative re sistor with the designated combination.
(5) Troubleshooting CAUTION Use a servomotor with electromagneti c brakes or establish an external b rake mechanism for the purpose of holding; this serv es as countermeas ures for possible hazard ous situation caused by power failure o r product fault.
CAUTION Do not short-circuit, charge, overheat, incinerate or d isa ssemble the battery . The hard disk unit has a service life, and must be replace d before its expiration. As a precautionary measure, alway s back up the customer ’ s data stored in the hard disk unit.
I CONTENTS I. Connection Manual 1. OUTLINE .................................................................................................................... ...... I -1 2. CONFIGURATION ..............................................................
II 5. CONNECTION OF CO MMUNICATION TERMINAL ....................................................... I -48 5.1 Outline of Communication Terminal ........................................................................ I- 48 5.2 Connection of Power Supply .
III APPENDIX 5 OUTLINE AND INSTALLATION DIMENSIONS FOR SYNCHRONOUS FEED ENCODER .......................................................... I -83 APPENDIX 6 OUTLINE AND INSTALLATION DIMENSIONS FOR GROUNDING PLATE AND CLAMP FITTING .....................
IV II. Maintenance Manual 1. OUTLINE .................................................................................................................... ..... II -1 1.1 Table of Configuration Lists ....................................................
I. Connection Manual.
1. OUTLINE I - 1 1. OUTLINE This manual explains the items required fo r installing and connecting the MELDAS C6/C64. Read this manual thoroughly and understand the product' s functions and performance before starting to use.
2. CONFIGURATION 2.1 System Configuration I - 2 2. CONFIGURATION 2.1 System Configuration MITSUBISHI MELDAS C64 Other C6/C6 4 control unit C6/C64 control un it Synchronous feed encoder Manual pulse gene rator RS-232C device Max.
2. CONFIGURATION 2.2 List of Configuration Units I - 3 2.2 List of Configuration Units 1. Control unit Type Configuration element Details HR851 card Main card HR891 card Back panel FCU6-MU043 FCU6-MU042 FCU6-MU041 C6 Control unit C64 Control unit C64T Control unit HR899 card IC card interface 2.
2. CONFIGURATION 2.2 List of Configuration Units I - 4 3. Communication terminal (display/NC key board) Type Configuration element Details 7.2- type mono- chrome LCD RX213 card FCUA-LD100 7.2-type monochrome LCD with integrated keyboard (Integrated type/machining system sheet) Key switch / escutcheon Control card 24VDC input 7.
2. CONFIGURATION 2.2 List of Configuration Units I - 5 5. Remote I/O unit Type Configuration element Details RX311 Base PCB : DI (sink/source)/ DO (sink) = 32/32 FCUA-DX100 DI (sink/source)/DO (sink) .
3. INSTALLATION 3.1 General Specification I - 6 3. INSTALLATION 3.1 General Specification Type name FCU6-MU043/MU042/MU041 Unit name Control unit During operation 0 to 55°C Ambient temperature During.
3. INSTALLATION 3.1 General Specification I - 7 Type name FCUA-LD100/ FCUA -LD10+KB20 FCU6-DUT32 +KB021 FCUA-CT100/ FCUA-CR10+KB10 Unit name Communication terminal During operation 0 to 50°C 0 to 55.
3. INSTALLATION 3.2 General Connection Diagram I - 8 3.2 General Connection Diagram R S T No-fuse breaker (NFB) 3-phase 200V AC to 230V AC Insert when required OFF ON MC MC C6 DCIN S tablized power su.
3. INSTALLATION 3.2 General Connection Diagram I - 9 CN1A CN1B L2 L3 C L1 L21 MC1 N D U V W FG FG FG CN2 L1 P CN1A CN1B L2 L3 C L1 L21 MC1 N D U V W FG FG FG CN2 P L1 IM Detector SM S pindle motor wit.
3. INSTALLATION 3.2 General Connection Diagram I - 10 (3) Example of Connection w hen Using V1/V2/SP for Driv e Section Connect to control unit SERVO 1 AC ser v omoto r Motor end detector S pindle mot.
3. INSTALLATION 3.3 Countermeasures against Heat Radiation I - 11 3.3 Countermeasures against Heat Radiation Please refer to the following procedures for heat radiation countermeasures.
3. INSTALLATION 3.4 Noise Countermeasures I - 12 3.4 Noise Countermeasures 3.4.1 Connection of Frame Ground (FG) The frame should basically be grounded at one ground point. Connect the control unit and base I/O unit's 0V (RG) to the FG on the 24VDC stabilized power supply side.
3. INSTALLATION 3.4 Noise Countermeasures I - 13 3.4.2 Shield Clamping of Cables The shield cable connected to the control unit, servo amplifier and spindle amplifier must be connected to the grounding plate to stabilize operation while preventing malfunctioning due to noise.
3. INSTALLATION 3.4 Noise Countermeasures I - 14 The cables connected to the control unit for which the shield must be connected to the ground are shown below.
3. INSTALLATION 3.4 Noise Countermeasures I - 15 3.4.4 Countermeasures against Lightning Surge Protection Generally, lightning surge infiltrates the control power supply from the power supply line. This control power supply or the internal circuit can be damaged by lightning surge via the control power supply.
3. INSTALLATION 3.4 Noise Countermeasures I - 16 (2) Examples of surge absorbers Types of Okay a Electric surge absorbers Surge absorber Type Circuit voltage [Vrms] Max. tolerable circuit voltage [Vrms] Clamp voltage [V] ± 10% Surge resistance level 8/20 µ s [A ] Surge w ithstand voltage (Electrical-discharge start voltage) 1.
3. INSTALLATION 3.5 Installation I - 17 3.5 Installation Each unit is installed in the sealed structure cabinet as a principle. When installing into the cabinet, refer to the following drawings to consider the cont rol unit's heat radiation and wiring, and secure enough space for ventilation.
3. INSTALLATION 3.6 Mounting Conditions I - 18 3.6 Mounting Conditions (1) Parts, highly susceptible to dust, are mounted with a high density inside the unit. Always use a sealed structure for the c abinet, and provide the following treatments. • Always plug the cable inlet with packi ng to prevent dust and oil from entering.
3. INSTALLATION 3.7 Turning the Pow er ON Again I - 19 3.7 Turning the Power ON Again When turning the control unit power ON again after turni ng it OFF, wait at least five seconds or more. If the power is turned ON in less than five seconds, the system may not start up.
4. CONTROL UNIT CONNECTIONS 4.1 Names of Each Control Unit Part I - 20 4. CONTROL UNIT CONNECTIONS The methods for connecting to each unit and device from the control unit are briefly explained in this section.
4. CONTROL UNIT CONNECTIONS 4.2 Connecting the Pow er Supply I - 21 4.2 Connecting the Power Supply A 24VDC power supply is required for the control uni t. Prepare a stabilized power supply that satisfies the following conditions. The DC24VIN connector is used to connect the power supply.
4. CONTROL UNIT CONNECTIONS 4.3 Connecting the Communication Terminal I - 22 4.3 Connecting the Communication Terminal The TERMINAL connector is used to connect the communication terminal (FCUA-L D100, etc.). On the communication terminal side, connect the R000 c able to the CR02 connector, and supply the 24VDC power supply to the CR01 connector.
4. CONTROL UNIT CONNECTIONS 4.4 Connecting the Synchronous Feed Encoder I - 23 4.4 Connecting the Synchronous Feed Encoder The ENC connector is used to connect the sy nchronous feed encoder. Use the CS050 or CS054 connector set (optional, with both ends) when manufac turing the R050 or R054 cable.
4. CONTROL UNIT CONNECTIONS 4.5 Connecting the Sensor Signal (skip) I - 24 4.5 Connecting the Sensor Signal (skip) The SKIP connector is used to c onnect the sensor signal (skip). The sensor signal is used for high-speed signal proce ssing, so take special care to prevent noise induction, etc.
4. CONTROL UNIT CONNECTIONS 4.6 Connecting the Servo Drive Unit I - 25 4.6 Connecting the Servo Drive Unit The SERVO1 connector is used to connect the serv o drive unit. Connect the R000 cable from SERVO1 connector on the control unit to CN1A connector on the servo drive unit.
4. CONTROL UNIT CONNECTIONS 4.7 Connecting the Manual Pulse Generator I - 26 4.7 Connecting the Manual Pulse Generator The HANDLE connector is used to connect the manual pulse generator. Up to three manual pulse generators can be connected. Use the CS000 connector set (optional, with both ends) when manufacturing the F320, F321 or F322 cable.
4. CONTROL UNIT CONNECTIONS 4.8 Connecting the Machine Control Signal I - 27 4.8 Connecting the Machine Control Signal Machine input/output signal types and No.
4. CONTROL UNIT CONNECTIONS 4.8 Connecting the Machine Control Signal I - 28 <Outline of connection> A 2 B2 Mac hi ne control panel DIO B1 A 1 24VDC(+) COM 2.2k Ω SA 0V PL Input circuit sink type Output circuit source type Control circuit S tabilized power supply DCIN 24VDC ( + ) 0V FG 0V 1 2 3 RA A 2 B2 DIO B1 A 1 24VDC(+) 0V COM 2.
4. CONTROL UNIT CONNECTIONS 4.8 Connecting the Machine Control Signal I - 29 <Signal assignment table> DIO Note) The emergency stop signal is input into X7. The PLC interface assignments correspond to X400 to X40F . DO RA <Applicable connector> DI DO DI Extension DIO unit (option mountin g) DIO Machine side control panel, etc.
4. CONTROL UNIT CONNECTIONS 4.8 Connecting the Machine Control Signal I - 30 <Outline of input circuit> The digital signal input circuit includes the sink type and source type. These can be selected by each connector unit. Input circuit Contro l circuit 2.
4. CONTROL UNIT CONNECTIONS 4.8 Connecting the Machine Control Signal I - 31 <Outline of output circuit> There are a sink type (HR881/882) and source ty pe (HR883/884) digital signal output circuits. The SA (servo READY) output circ uit is a source type.
4. CONTROL UNIT CONNECTIONS 4.9 Connecting the Remote I/O Unit I - 32 4.9 Connecting the Remote I/O Unit The RIO-M connector is used to connect the remote I/O unit. Connect the R211 cable from the RIO-M connector on the control unit to RIO1 on the remote I/O unit.
4. CONTROL UNIT CONNECTIONS 4.9 Connecting the Remote I/O Unit I - 33 <Connection to use C6 as slave station> When using the C64 and M600 Series, etc., as the master station and C6 as the slave station, use the RIO-M/S connector. Connect the R211 cabl e from the master station to the RIO-M/S connector on C6.
4. CONTROL UNIT CONNECTIONS 4.10 Connecting the RS-232C Device I - 34 4.10 Connecting the RS-232C Device The SIO connector is used to connect the RS-232C device (serial I/O). The F310 and F311 relay cables are required to c onnect the RS-232C cable. (Refer to the CABLE MANUFACTURING DRAWINGS for details.
4. CONTROL UNIT CONNECTIONS 4.11 Connecting Other Peripheral Devices I - 35 4.11 Connecting Other Peripheral Devices When connecting the MELSEC PLC peripheral devices using the RS-422 interface, connect to the GPP connector side of the F311 relay cable connected to the SIO connector.
4. CONTROL UNIT CONNECTIONS 4.11 Connecting Other Peripheral Devices I - 36 (b) F314 (For personal computer/communication terminal) NC side (TERMINAL) (20pin half-pi tch) PC side (25pin D-SUB) Signal Pin No. Cable con nection & Sig nal directi on Pin No.
4. CONTROL UNIT CONNECTIONS 4.11 Connecting Other Peripheral Devices I - 37 (5) RS-232C cable (F316) MELDAS C6/C 64 side (20pin half-pi tch) GOT side (9pin D-SUB) Signal Pin No.
4. CONTROL UNIT CONNECTIONS 4.12 Connecting the Display Unit with Ethernet I - 38 4.12 Connecting the Display Unit with Ethernet To connect the display unit with Ethernet, the Et hernet card (FCU6-EX875) must be mounted to the extension slot EXT2 on the control unit.
4. CONTROL UNIT CONNECTIONS 4.13 Connecting the Netw ork w ith MELSECNET/10 I - 39 4.13 Connecting the Network with MELSECNET/10 The coaxial bus type and optical loop type networ ks can be used between the controllers in the MELSECNET/10 data link system.
4. CONTROL UNIT CONNECTIONS 4.13 Connecting the Netw ork w ith MELSECNET/10 I - 40 (2) Connecting the optical loop type MELSECNET/10 Connect a dedicated optical fiber cable to t he optical connector on the MELSECNET/10 unit (FCU6-EX879). (Note 1 ) An indoor standard cable AS-2P-5M-A, etc.
4. CONTROL UNIT CONNECTIONS 4.14 Connecting the IO Device with CC-Link I - 41 4.14 Connecting the IO Device with CC-Link The CC-Link unit (FCU6-HR865) must be mounted in the control unit's extension slot to connect IO devices using CC-Link. Connect a dedicated CC-Link cable to the CC- Link unit (FCU6-HR865) terminal block.
4. CONTROL UNIT CONNECTIONS 4.14 Connecting the IO Device with CC-Link I - 42 Wiring the CC-Link terminal block (1) Peel the cable's sheath, and separate the inner wire from the shield mesh. (2) Peel the shield mesh and the inner wire's sheath, and twist the core wires.
4. CONTROL UNIT CONNECTIONS 4.15 Connecting the IO Device with DeviceNet I - 43 4.15 Connecting the IO Device with DeviceNet The DeviceNet unit (FCU6-EX871-40) must be mounted in the control unit's extension slot to connect IO devices with DeviceNet.
4. CONTROL UNIT CONNECTIONS 4.15 Connecting the IO Device with DeviceNet I - 44 Wiring the DeviceNet terminal block (1) Peel the cable's sheath, and separate the inner wire from the shield mesh. (2) Peel the shield mesh and the inner wire's sheath, and twist the core wires.
4. CONTROL UNIT CONNECTIONS 4.16 Control Unit Connector Pin Assignments I - 45 4.16 Control Unit Connector Pin Assignments Se r vo drive unit SERVO1 1 10 11 20 <Cable side connec tor type> Plug .
4. CONTROL UNIT CONNECTIONS 4.16 Control Unit Connector Pin Assignments I - 46 Serial SIO 1 10 11 20 <Cable si d e co n nector t ype > Plug : 10120-600 0EL Shell : 10320-321 0-000 Recommended ma.
4. CONTROL UNIT CONNECTIONS 4.16 Control Unit Connector Pin Assignments I - 47 1 2 3 I/O I/O TXRX1 TXRX1* GND Remote I/O RIO-M 3 1 <Cable side c onnector type> Connector : 1-178288- 3 Contact : .
5. CONNECTION OF COMMUNICATION TERMINAL 5.1 Outline of Communication Terminal I - 48 5. CONNECTION OF COMMUNICATION TERMINAL The communication terminal is described in this chapter. 5.1 Outline of Communication Terminal The communication terminal is configured of the display and keyboard.
5. CONNECTION OF COMMUNICATION TERMINAL 5.2 Connection of Pow er Supply I - 49 5.2 Connection of Power Supply The 24VDC must be supplied to the communication terminal. Prepare a stabilized power supply that satisfies the following conditions. The 9-type CRT type requires 100VAC for the CRT power supply.
5. CONNECTION OF COMMUNICATION TERMINAL 5.2 Connection of Pow er Supply I - 50 5.2.2 Connection of Power Supply to 10.4-type Monochrome LCD (FCU6-DUT32+KB021) Supply 24VDC to the CR01 connector on the rear of the LCD.
5. CONNECTION OF COMMUNICATION TERMINAL 5.2 Connection of Pow er Supply I - 51 5.2.3 Connection of Power Supply to 9-type CRT (FCUA-CT100/FCUA-CR10+KB10) Supply 100VAC to the connector CRT2 on the rear of the CRT, and 24VDC to the connector CR01 on the rear of the keyboard.
5. CONNECTION OF COMMUNICATION TERMINAL 5.3 Internal Connections I - 52 5.3 Internal Connections 7.2-inch LCD Menu k eys J2 Data keys J2 J1 CNZ24 PCB CR03 CNZ22A CR01 R220 cable R000 cable 24VDC(+) To.
5. CONNECTION OF COMMUNICATION TERMINAL 5.4 Connection of Remote I/O Unit I - 53 5.4 Connection of Remote I/O Unit A maximum of two remote I/O units can be connect ed to the communication terminal.
5. CONNECTION OF COMMUNICATION TERMINAL 5.5 Example of Connecting Multiple Cont rol Units to the Communication Terminal I - 54 5.5 Example of Connecting Multiple C ontrol Units to the Communication Te.
6. CONNECTION OF REMOTE I/O UNIT 6.1 Outline of Remote I/O Unit I - 55 6. CONNECTION OF REMOTE I/O UNIT This chapter describes the connection between remote I/O unit and machine control signals.
6. CONNECTION OF REMOTE I/O UNIT 6.2 Names of Each Remote I/O Unit Section I - 56 6.2 Names of Each Remote I/O Unit Section DS FCU A -DX10 Front view FCU A -DX1 1 / FCU A -DX12 FCU A -DX13.
6. CONNECTION OF REMOTE I/O UNIT 6.3 Setting the Station No. When Using Multiple Remote I/O Units I - 57 6.3 Setting the Station No. When Using Multiple Remote I/O Units When the remote I/O unit is connected with serial lin ks (MC link B), multiple units can be used as long as the total No.
6. CONNECTION OF REMOTE I/O UNIT 6.4 Connection of Remote I/O Pow er Supply I - 58 6.4 Connection of Remote I/O Power Supply 24VDC(+) is required to run the remote I/O unit. Prepare a stabilized power supply that satisfies the following conditions. Output voltage 24VDC ± 5% Ripple ± 5% (P-P) FCUA-DX10 2.
6. CONNECTION OF REMOTE I/O UNIT 6.5 Outline of Digital Signal Input Circuit I - 59 6.5 Outline of Digital Signal Input Circuit The digital signal input circuit can be selected fr om sink type or source type in card units. Input circuit COM (Machine side) A 3,B3 Sink type DI-L/DI-R 0V 0V 0V 0V 0V 24VDC(+) 2.
6. CONNECTION OF REMOTE I/O UNIT 6.5 Outline of Digital Signal Input Circuit I - 60 Input conditions The input signals must be used within the following condition ranges. Sink type Input voltage at external contact ON 6V or less Input current at external contact ON 9mA or more Input voltage at external contact OFF 2 0V or mo re, 2 5 .
6. CONNECTION OF REMOTE I/O UNIT 6.6 Outline of Digital Signal Output Circuit I - 61 6.6 Outline of Digital Signal Output Circuit The digital signal output circuit uses a sink type (DX1 0) or source type (DX1 1). Use within the specific ation ranges shown below.
6. CONNECTION OF REMOTE I/O UNIT 6.7 Outline of Analog Signal Output Circuit I - 62 6.7 Outline of Analog Signal Output Circuit The analog signal output circuit can be used only for the FCUA-D X120/DX121/DX140/DX141.
6. CONNECTION OF REMOTE I/O UNIT 6.8 Outline of Analog Signal Input Circuit I - 63 6.8 Outline of Analog Signal Input Circuit The analog signal input circuit can be used only for the FCUA-DX140/DX141. Input circuit A DC 150 Ω A I A I* Input conditions Max.
6. CONNECTION OF REMOTE I/O UNIT 6.9 Connection of FCUA-DX10 /13 /14 Unit and Machine Control Signal I - 64 6.9 Connection of FCUA-DX10 /13 /14 Unit and Machine Control Signal Input Output Type of machine input/output signal and No.
6. CONNECTION OF REMOTE I/O UNIT 6.9 Connection of FCUA-DX10 /13 /14 Unit and Machine Control Signal I - 65 <Signal assignment table> DI-L Machine side control pane l, etc. <CAUTION> When using two or more re mo te I/ O units or when connec tin g to the communica tion terminal , the signal assignment w ill differ .
6. CONNECTION OF REMOTE I/O UNIT 6.10 Connection of FCUA-DX11 Unit and Machine Control Signal I - 66 6.10 Connection of FCUA-DX11 Unit and Machine Control Signal Input Output Type of machine input/output signal and No.
6. CONNECTION OF REMOTE I/O UNIT 6.10 Connection of FCUA-DX11 Unit and Machine Control Signal I - 67 <Signal assignment table> <CAUTION> When using two or more remote I/O units or when connecting to the communicat ion terminal, the signal assignment will differ .
6. CONNECTION OF REMOTE I/O UNIT 6.11 Connection of FCUA-DX12 Unit and Machine Control Signal I - 68 6.11 Connection of FCUA-DX12 Unit and Machine Control Signal Input Output Analog output Type of machine input/output signal and No.
6. CONNECTION OF REMOTE I/O UNIT 6.11 Connection of FCUA-DX12 Unit and Machine Control Signal I - 69 <Signal assignment table> <CAUTION> When using two or more remote I/O units or when connecting to the communication terminal, the signal assignment will differ .
6. CONNECTION OF REMOTE I/O UNIT 6.12 Connection of FCUA-DX13 Unit and Manual Pulse Generator I - 70 6.12 Connection of FCUA-DX13 Unit and Manual Pulse Generator When connecting the manual pulse generator, the R041 or R042 cable is connected to HANDLE.
6. CONNECTION OF REMOTE I/O UNIT 6.13 Outline of FCUA-DX13 Unit Pulse Input Circuit I - 71 6.13 Outline of FCUA-DX13 Unit Pulse Input Circuit When connecting a pulse generator other than the manual pulse generator (FCUA-HD60) to the FCUA-DX13 unit, use within the specif ications range given below.
6. CONNECTION OF REMOTE I/O UNIT 6.14 Connection of FCUA-DX14 Unit and Analog Input/Output Signal I - 72 6.14 Connection of FCUA-DX14 Unit and Analog Input/Output Signal For the analog input/output signal, the R031 cable is connected to AI0. Up to four input points and one output point of the analog input/ output signal can be connected.
6. CONNECTION OF REMOTE I/O UNIT 6.15 Cables I - 73 6.15 Cables The remote I/O unit cable types include the R300 and R301 cables. The R300 cable has one end cut off, and the R301 cable is used for connections with the Izumi Denki terminal block BX1F-T40A (Note 1) .
APPENDIX 1 OUTLINE AND INSTALLATI ON DIMENSIONS FOR CONTROL UNIT Appendix 1.1 Outline and Installation Dimensions for Control Unit I - 74 APPENDIX 1 OUTLINE AND INSTALLATION DIMENSIONS FOR CONTROL UNIT Appendix 1.1 Outline and Installation Dimensions for Control Unit RIO-M RIO-M/S 30 60 2-M 5 ×0 .
APPENDIX 1 OUTLINE AND INSTALLATI ON DIMENSIONS FOR CONTROL UNIT Appendix 1.2 Outline and Installation Dimensions for Control Unit w ith External Extension Unit I - 75 Appendix 1.2 Outline and Installation Dimensions for Control Unit with External Extension Unit 30 60 380 360 ± 0.
APPENDIX 2 OUTLINE AND INSTALLATION DI MENSIONS FOR COMMUNICATION TERMINAL Appendix 2.1 Outline and Installation Dimensions for FCUA-CT100 I - 76 APPENDIX 2 OUTLINE AND INSTALLATION DIMENSIONS FOR COMMUNICATION TERMINAL Appendix 2.
APPENDIX 2 OUTLINE AND INSTALLATION DI MENSIONS FOR COMMUNICATION TERMINAL Appendix 2.2 Outline and Installation Dimensions for FCUA-CR10 I - 77 Appendix 2.2 Outline and Installation Dimensions for FCUA-CR10 250 242 (Square hole dimensi ons) 120 ± 0.
APPENDIX 2 OUTLINE AND INSTALLATION DI MENSIONS FOR COMMUNICATION TERMINAL Appendix 2.3 Outline and Installation Dimensions for FCUA-LD100 I - 78 Appendix 2.3 Outline and Installation Dimensions for FCUA-LD100 MITSUBISHI 382 (Square hole) 9 9 5 130 140 130 130 260 8- φ 4hole(for M3 screw) 5 5 180 10 9 9 190 5 10 70 130 ± 0.
APPENDIX 2 OUTLINE AND INSTALLATION DI MENSIONS FOR COMMUNICATION TERMINAL Appendix 2.4 Outline and Installation Dimensions for FCUA-LD10 and KB20 I - 79 Appendix 2.4 Outline and Installation Dimensions for FCUA-LD10 and KB20 MITSUBISHI 120 130 260 6- φ 4 hole (for M3 screw) 5 5 180 6-M3 scre w 248 (square hole dimensi ons ) 130 ± 0.
APPENDIX 2 OUTLINE AND INSTALLATION DI MENSIONS FOR COMMUNICATION TERMINAL Appendix 2.5 Outline and Installation Dimensions for FCU6-DUT32, KB021 I - 80 Appendix 2.5 Outline and Installati on Dimensions for FCU6-DUT32, KB021 140 210 Menu keys 270 Escutcheon M3x8 scre w Protective cover 45 (50) 20 20 30 6- φ 4 hole 182 ± 0.
APPENDIX 3 OUTLINE AND INSTALLATION DIMENSIONS FOR REMOTE I/O UNIT I - 81 APPENDIX 3 OUTLINE AND INSTALLATION DIMENSIONS FOR REMOTE I/O UNIT 40 135 70 Wi r in g allowance 135 6 168 Heat radiati on allowance 2-M5-0.
APPENDIX 4 OUTLINE AND INSTALLATION DI MENSIONS FOR MANUAL PULSE GENERATOR I - 82 APPENDIX 4 OUTLINE AND INSTALLATION DIMENSIONS FOR MANUAL PULSE GENERATOR 3 - φ 4.8 Equal φ 62 +2 0 φ 72 ± 0.2 (Trisection) 120 ° Packing t2 .0 3.6 φ 77 ± 0.5 φ 80 ± 1 φ 60 ± 0.
APPENDIX 5 OUTLINE AND INSTALLATION DIMENSIONS FOR SYNCHRONOUS FEED ENCODER I - 83 APPENDIX 5 OUTLINE AND INSTALLATION DIMENSIONS FOR SYNCHRONOUS FEED ENCODER A 1chA K 0V B 2chZ L C 3chB M D N 1chA E Case ground P 2chZ F R 3chB G S H +5V T J 68 56 68 56 φ 68 Caution plate Detector (1024P/rev) φ 50 19.
APPENDIX 6 OUTLINE AND INSTALLATION DI MENSIONS FOR GROUNDING PLATE AND CLAMP FITTING I - 84 APPENDIX 6 OUTLINE AND INSTALLATION DIMENSIONS FOR GROUNDING PLATE AND CLAMP FITTING The shield wire generally only needs to be grounded to the connector's case frame.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS I - 85 APPENDIX 7 CABLE MANUFACTURING DRAWINGS As a rule, most F /R cables used with this product ar e not sold by Mitsubishi. Thus, manufacture the required cables using the cable manufacturing drawings on the following pages as a reference.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.1 F310 Cable Manufacturing Draw ing I - 86 Appendix 7.1 F310 Cabl e Manufacturing Draw ing Application : Control unit - serial device connection (Cable from control unit to junction plate.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.2 F311 Cable Manufacturing Draw ing I - 87 Appendix 7.2 F311 Cabl e Manufacturing Draw ing Application : Control unit - serial device connection (Cable from control unit to junction plate.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.3 F320 Cable Manufacturing Draw ing I - 88 Appendix 7.3 F320 Cabl e Manufacturing Draw ing Application : Control unit - manual pulse generator connec.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.4 F321 Cable Manufacturing Draw ing I - 89 Appendix 7.4 F321 Cabl e Manufacturing Draw ing Application : Control unit - manual pulse generator connec.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.5 F322 Cable Manufacturing Draw ing I - 90 Appendix 7.5 F322 Cabl e Manufacturing Draw ing Application : Control unit - manual pulse generator connec.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.6 F340 Cable Manufacturing Draw ing I - 91 Appendix 7.6 F340 Cabl e Manufacturing Draw ing Application : External skip signal input (4 points) List of parts used F340 Note (2) 1 2 3 5 Cotrol unit side Skip signal inpu t 4 SKIP F340 Assembly dr awin g No.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.7 F350 Cable Manufacturing Draw ing I - 92 Appendix 7.7 F350 Cabl e Manufacturing Draw ing Application : Control unit - machine electric cabinet List of parts used No.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.8 F351 Cable Manufacturing Draw ing I - 93 Appendix 7.8 F351 Cabl e Manufacturing Draw ing Application : Extension DIO - machine electric cabinet List of parts used No.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.9 FCUA-R000 Cable Manufacturing Draw ing I - 94 Appendix 7.9 FCUA-R000 Ca ble Manufacturing Draw ing Application : Control unit – servo drive unit connection Servo drive unit – servo drive unit connection Control unit - communication terminal connection, etc.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.10 FCUA-R050 Cable Manufacturing Draw ing I - 95 Appendix 7.10 FCUA-R050 Ca ble Manufacturing Draw ing Application : Control unit - synchronous feed .
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.11 FCUA-R051 Cable Manufacturing Draw ing I - 96 Appendix 7.11 FCUA-R051 Ca ble Manufacturing Draw ing Application : Control unit - synchronous feed .
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.12 FCUA-R054 Cable Manufacturing Draw ing I - 97 Appendix 7.12 FCUA-R054 Ca ble Manufacturing Draw ing Application : Control unit - synchronous feed .
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.13 FCUA-R055 Cable Manufacturing Draw ing I - 98 Appendix 7.13 FCUA-R055 Ca ble Manufacturing Draw ing Application : Control unit - synchronous feed .
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.14 FCUA-R211 Cable Manufacturing Draw ing I - 99 Appendix 7.14 FCUA-R211 Ca ble Manufacturing Draw ing Application: Control unit – remote I/O unit .
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.15 FCUA-R220 Cable Manufacturing Draw ing I - 100 Appendix 7.15 FCUA-R220 Ca ble Manufacturing Draw ing Application: Supply of 24V to control unit, r.
APPENDIX 7 CABLE MANUFACTURING DRAWINGS Appendix 7.16 F300 Cable Manufacturing Draw ing I - 101 Appendix 7.16 F300 Cabl e Manufacturing Draw ing Application : Main card in control unit – front panel internal connection List of parts used 1 2 4 3 F300 F300 Y 11 5 ± 5mm Assembly dr awin g No.
The procurement type is FCUA-CS/CN □□□ . Connector type A pplication Package contents CS000 Control unit - CT100 Control unit - C1 C1-C1 Connector (3M) 10120-3000VE × 2 pcs. Connector case (3M) 10320-52F0-008 × 2 pcs. CS020 Control unit - General-purpose RS-232C device Connector (3M) 10120-3000VE × 1 pc.
The procurement type is FCUA-CS/CN □□□ . Connector type A pplication Package contents CN211 IO communication connector Connector (Tyco Electronics AMP) 1-178288-3 × 1 pc. Y X D-3 AMP Gold contact (Tyco Electronics AMP) 1-175218-2 × 3 pcs. CN220 24VDC power supply connector Connector (Tyco Electronics AMP) 2-178288-3 × 1 pc.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.1 Introduction I - 104 APPENDIX 9 EMC INSTALLATION GUIDELINES Appendix 9.1 Introduction EMC Directives became mandatory as of January 1, 1996. The target products must have a CE mark attached indicating that the product complies with the Directives.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.2 EMC Directives I - 105 Appendix 9.2 EMC Directives The EMC Directives largely r egulate the following two items. • Emission ..... Capacity to prevent out put of obstructive noise that adv ersely affects external devices.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.3 EMC Countermeasures I - 106 Appendix 9.3 EMC Countermeasures The main items relating to EMC countermeasures include the following. (1) Store the device in a sealed metal panel. (2) Ground all conductors that are floating electrically.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.4 Panel Structure I - 107 Appendix 9.4 Panel Structure The design of the panel is a very important factor for the EMC countermeasures, so take the following countermeasures into consideration. Appendix 9.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.4 Panel Structure I - 108 Appendix 9.4.2 Countermeasures for door (1) Use metal for all members configuring the door. (2) When joining the door, use a gasket to lower t he impedance of the contacting sections, or use a structure with a large contact area as shown below.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.4 Panel Structure I - 109 Appendix 9.4.3 Countermeasures for power supply (1) Shield the power supply section and insert a filt er to prevent the noise from flowing in or out. Selection of the noise filter capacity will differ according to the drive amplifier and devices being used.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.5 Countermeasures for Wiring in Panel I - 110 Appendix 9.5 Countermeasures for Wiring in Panel Cables act as antennas to propagate unnecessary noi se, and thus must be appropriately shielded and treated.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.5 Countermeasures for Wiring in Panel I - 111 Appendix 9.5.2 NC Unit grounding wire Operation panel Control pan el Control unit FG cable FG cable 200.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.5 Countermeasures for Wiring in Panel I - 112 Appendix 9.5.3 Shield treatment of cables Use shielded cables for the cables wir ed outside the panel in the C6/C64 Series. Use a shield clamp (refer to 9.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.5 Countermeasures for Wiring in Panel I - 113 (3) Servo communication cable [FCUA-R000 cable] • Use a shield clamp within 10cm from the panel's inlet/outlet. • Install a ferrite core on both ends of the connected units.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.6 Parts for EMC Countermeasures I - 114 Appendix 9.6 Parts for EMC Countermeasures Appendix 9.6.1 Shield clamp fitting The effect can be enhanced by directly connecting the outer sheath of the cabl e to the grounding plate as shown below.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.6 Parts for EMC Countermeasures I - 115 Appendix 9.6.2 Ferrite core The ferrite core is mounted integrally with the plastic case. This can be installed with one touch without cutti ng the interface cable or power supply cable.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.6 Parts for EMC Countermeasures I - 116 Appendix 9.6.3 Surge protector (1) Surge absorber Make sure that surge does not directly enter the AC line of the general-purpose stabilized power supply (prepared by user) supplied to the c ontrol unit and DIO.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.6 Parts for EMC Countermeasures I - 117 (2) Part name : RAV-781BYZ-4 Manufacturer : Okatani Denki Sangyo Circuit voltage 50/60Hz Vrms Max. tolerab le circuit voltage Clamp vol t a ge V ± 10% Surge resistance level 8/20µs Surge w ithstand voltage 1.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.6 Parts for EMC Countermeasures I - 118 (2) Example of surge absorber installation Example of surge absorber in stallation Control panel (Rel ay pa nel, etc.
APPENDIX 9 EMC INST ALLATION GUIDELINES Appendix 9.6 Parts for EMC Countermeasures I - 119 Appendix 9.6.4 Selection of stabilized power supply Consider the following characteristics when select ing the stabilized power supply (prepared by user). Use a power supply that complies with CE Marking or that follows the Safety Standards given below.
II. Maintenance Manual.
1. OUTLINE 1.1 Table of Configuration Lists II - 1 1. OUTLINE 1.1 Table of Configuration Lists The C6/C64 control unit is configured of the following modules.
1. OUTLINE 1.2 Control Section Module Configuration II - 2 1.2 Control Section Module Configuration Front panel Clear c over F300 cable HR899 card R400 cable Card installation fitting Fan Frame FG fit.
2. EXPLANATION OF MODULE FUNCTIONS 2.1 HR851 Card II - 3 2. EXPLANATION OF MODULE FUNCTIONS 2.1 HR851 Card [Block diagram] RISC DRAM SRAM FLROM RT C Cassette memory (For maintenance) External power supply 24VDC/3A External I/O interface RTBU S CPU peripheral control PLC operation Power supply circuit (DC/DC) Battery 3.
2. EXPLANATION OF MODULE FUNCTIONS 2.1 HR851 Card II - 4 [Connector layout diagram] FAN CS1 ICCARD RTBUS DC24IN TEST RIO-M/S ISP RIO-M CBUS SW 2 DIO NCRST LED3 SKIP U:TERM INAL L:SIO U:HANDLE L:ENC U:.
2. EXPLANATION OF MODULE FUNCTIONS 2.2 HR899 Card II - 5 2.2 HR899 Card [Block diagram] ICCARD SLOT [Explanation of functions] The HR899 card functions as the IC Card interface.
2. EXPLANATION OF MODULE FUNCTIONS 2.3 HR891 Card II - 6 2.3 HR891 Card [Block diagram] RTBUS For HR851 card connect ion For extensio n card connection For extension card connection For extension ba ck p anel co nnection RT2 RT1 EXRT [Explanation of functions] The HR891 card functions as the control unit's back panel.
2. EXPLANATION OF MODULE FUNCTIONS 2.4 HR881/882/883/884 Card II - 7 2.4 HR881/882/883/884 Card [Block diagram] RTBUS DI DO MAC303 DI I/F DO I/F Connect to control unit’s back panel MAC303 A O I/F M.
2. EXPLANATION OF MODULE FUNCTIONS 2.5 HR875/876 Card II - 8 2.5 HR875/876 Card [Block diagram] RTBUS Connect to control unit’s back panel Ethernet Controller EEPROM PLD T rans- former PCIEXT EXTPCI.
2. EXPLANATION OF MODULE FUNCTIONS 2.6 HR877/878 Card II - 9 2.6 HR877/878 Card [Block diagram] RTB U S Buff PLD HR877 HR878 Rotary switch, setting, et c.
2. EXPLANATION OF MODULE FUNCTIONS 2.6 HR877/878 Card II - 10 [Connector layout diagram] NETWORK x 100 x 10 x 10 x 1 x 1 GROUP STA TION DIPSW MODE ISP [Explanation of settings] NETWORK : Network No. setting sw itch Set the netwo rk number between 1 and 239 w ith the thr ee rotary sw itches.
2. EXPLANATION OF MODULE FUNCTIONS 2.7 HR877/879 Card II - 11 2.7 HR877/879 Card [Block diagram] RTBUS Buff PLD HR877 HR879 Rotary switch, setting, etc.
2. EXPLANATION OF MODULE FUNCTIONS 2.7 HR877/879 Card II - 12 [Connector layout diagram] OUT IN T R T R NETWORK x 100 x 10 x 10 x 1 x 1 GROUP ST A TION DIPSW MODE ISP [Explanation of settings] NETWORK : Network No. setting sw itch Set the netwo rk number between 1 and 239 w ith the thr ee rotary sw itches.
2. EXPLANATION OF MODULE FUNCTIONS 2.8 HR865 Card II - 13 2.8 HR865 Card [Block diagram] Rotary switch, setting, etc. EEPRO M SRAM CPU CC-Link master gate array R TBUS 2-port RAM OI Gate array fo r bus I/F DC/DC Te r m i n a l block PLD PROM [Explanation of functions] The HR865 card functions as the CC- Link's master/local station.
2. EXPLANATION OF MODULE FUNCTIONS 2.8 HR865 Card II - 14 [Explanation of settings] MODE : Mode setting switch Set the unit's operation state (Default setting: 0) Master station Local station 0 :.
2. EXPLANATION OF MODULE FUNCTIONS 2.8 HR865 Card II - 15 [Explanation of LEDs] L1 L2 L3 L4 L5 L6 L7 L8 R1 R2 R3 R4 R5 R6 R7 R8 LED display status Master station (St andby master station) Local statio.
2. EXPLANATION OF MODULE FUNCTIONS 2.9 HR871 Card II - 16 2.9 HR871 Card [Block diagram] R S 2 3 2 C R TBUS PLD EEPROM DeviceNet master modul e ST A1,ST A2 LED DPORT DNET SIO RS232C DNM [Explanation of functions] The HR871 card functions as the DeviceNet ma ster when the DeviceNet master module is added on.
3. TROUBLESHOOTING 3.1 List of Unit LEDs II - 17 3. TROUBLESHOOTING 3.1 List of Unit LEDs SKIP DIO EXT2 SERVO1 EXT1 MAINT ENANCE LED1 LE D2 ENC HANDLE SIO TERMINAL IC CARD DC24V IN SERVO2 LED1 LED2 DC.
3. TROUBLESHOOTING 3.2 Troubleshooting II - 18 3.2 Troubleshooting 3.2.1 Confirmation of trouble state Confirm "when", "when doing what", and "what kind of" trouble occurred. (1) When? What time did the trouble occur? (2) When doing w hat? What was the NC operation mode? • During automatic operation .
3. TROUBLESHOOTING 3.2 Troubleshooting II - 19 3.2.2 When in trouble If the system does not operate as planned or if there is any trouble in the operation, confirm the following points and then contact the Mitsubishi Service Center. − Examples of trouble − • The power does not turn ON.
3. TROUBLESHOOTING 3.2 Troubleshooting II - 20 (1) Problems related to the pow er supply The power does not turn ON. Cause Remedy The door interlock is applied. If the control panel door is not completely closed, close it. If the door interlock is applied even when the door is closed, the door interlock circuit is damaged.
3. TROUBLESHOOTING 3.2 Troubleshooting II - 21 The power turns OFF. Cause Remedy There is a problem in the power supply. Check whether the voltage fluct uates at certain time zones. Check whether an instantaneous power failure has occurred. A problem occurs when the peripheral device starts operating.
3. TROUBLESHOOTING 3.2 Troubleshooting II - 22 (3) Problems related to remote I/O The communication alarm LED ALM (red) lights. Cause Remedy The remote connection cable is not connected. The cable is disconnected or has a connector contact fault. Check the connection of the R211 cable between the NC control section and remote I/O unit.
4. DAILY MAINTENANCE AND PERIO DIC INSPECTION AND MAINTENANCE 4.1 Maintenance Tools II - 23 4. DAILY MAINTENANCE AND PERIODIC INSPECTION AND MAINTENANCE 4.
4. DAILY MAINTENANCE AND PERIO DIC INSPECTION AND MAINTENANCE 4.2 Maintenance Items II - 24 4.2.1 Escutcheon (1) Cleaning the escutcheon 1) Keep the rear side of the escutcheon as clean as possible. 2) Wipe the escutcheon with a soft, clean, dry clot h.
4. DAILY MAINTENANCE AND PERIO DIC INSPECTION AND MAINTENANCE 4.3 Replacement Methods II - 25 4.3 Replacement Methods 4.3.1 Cable If the cable is replaced without turning the power OFF, the normal unit or peripheral devices could be damaged, and risks could be imposed.
4. DAILY MAINTENANCE AND PERIO DIC INSPECTION AND MAINTENANCE 4.3 Replacement Methods II - 26 (2) For a flat cable type connector with latches, open the latches in the directions of the arrows, and pull the connector off.
4. DAILY MAINTENANCE AND PERIO DIC INSPECTION AND MAINTENANCE 4.3 Replacement Methods II - 27 4.3.2 Durable parts (1) Battery All data, such as the parameters and machin ing programs that need to be backed up when the power is turned OFF, are saved by a lithium batte ry installed in the control unit battery holder.
4. DAILY MAINTENANCE AND PERIO DIC INSPECTION AND MAINTENANCE 4.3 Replacement Methods II - 28 (2) Cooling fan A fan is mounted on the control unit to cool the inside of the control unit. Applicable cooling fan ........... 109P0424H702 (Sanyo Denki) or MMF-04C24DS-ROF (Melco Technolex) Cooling fan lif e.
4. DAILY MAINTENANCE AND PERIO DIC INSPECTION AND MAINTENANCE 4.3 Replacement Methods II - 29 4.3.3 Control Unit (1) Control unit Always turn the machine power OFF before replacing the control unit. (1) Disconnect all cables connected to the control unit.
4. DAILY MAINTENANCE AND PERIO DIC INSPECTION AND MAINTENANCE 4.3 Replacement Methods II - 30 (2) Remote I/O unit Always turn the machine power OFF befor e replacing the remote I/O control unit. (1) Disconnect all cables connec ted to the remote I/O unit.
4. DAILY MAINTENANCE AND PERIO DIC INSPECTION AND MAINTENANCE 4.3 Replacement Methods II - 31 4.3.4 Control PCB (1) Main card Always turn the control unit power OFF before replacing the main card. (1) Confirm that the control unit power is OFF. (If the power is not OFF, turn it OFF.
4. DAILY MAINTENANCE AND PERIO DIC INSPECTION AND MAINTENANCE 4.3 Replacement Methods II - 32 (2) Extension card Always turn the control unit power O FF before replacing the extension card. (1) Confirm that the control unit power is OFF. (If the power is not OFF, turn it OFF.
Revision History Date of revision Manual No. Revision det a ils Nov . 1999 BNP-B2255A Correction of mist akes; Addition of Appendix 9 EMC Installation Guidelines Nov . 2000 BNP-B2255B • Details related to generation of smoke added to "Safe ty Precautions".
Notice Every effort has been made to keep up with sof tware and hardware revisions in the contents described in this manual. However , please understand that in some unavoidable cases simult aneous revision is not possible. Please contact your Mit subishi Electric dealer with any questions or comments regarding the use of this product.
BNP-B2255E(ENG) MC6/C64 008-107 (0403) MEE Specifications subject to change without notice. Printed in Japan on recycled paper. MITSUBISHI ELEC T R IC CO R PO R A T ION HEAD OFFICE : MITSUBISHI DENKI BLDG., 2-2-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN MODEL Manual No.
Een belangrijk punt na aankoop van elk apparaat Mitsubishi Electronics C6/C64 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Mitsubishi Electronics C6/C64 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Mitsubishi Electronics C6/C64 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Mitsubishi Electronics C6/C64 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Mitsubishi Electronics C6/C64 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Mitsubishi Electronics C6/C64 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Mitsubishi Electronics C6/C64 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Mitsubishi Electronics C6/C64 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.