Gebruiksaanwijzing /service van het product 932035 - 724 van de fabrikant Ariens
Ga naar pagina of 32
Owner/Operator Man ual Models 932035 - 724 932503 - 724 932101 - 824 932309 - 824 Sno-Thr o ® 03245600D 4/02 Supercedes 03245600,A,B,C Printed in USA ENGLISH FRANÇAIS ESP A Ñ OL T r ansfer model & serial number label from product registration here.
2 4/29/02 MODEL CERTIFICA TE OF CONFORMITY ISSUED BY THE MANUF ACTURER CERTIFICA T DE CONFORMIT É DU MOD È LE D É LIVR É P AR LE F ABRICANT MODELL-K ONFORMIT Ä TSBESCHEINIGUNG A USGESTELL T DURCH.
3 4/29/02 Stated Sound P ower Le vels are established f ollowing Anne x V “ Inter nal Control of Production ” of directive 2000/14/EC and assessment procedure EN-ISO 3744:1995.
4 ENGLISH 1. T raction Dr ive Clutch Lev er 2. Ignition Switch, push-pull 3. Choke 4. Throttle (Engine Stop) 5. Runner(s) 6. Axle Lock Pin (932101, 309) 7. Belt Cov er 8. Headlight (932101, 309) 9. Discharge Chute De fl ector 10. Discharge Chute 11. Impeller 12.
5 Figure 1 OS0502 OS2100 1 2 3 4 22 21 20 19 18 17 16 15 14 5 7 9 10 11 12 13 8 6.
GB - 6 Controls and Features . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Operation . . . . . . . . . . . . . . . . . . . . . . .
GB - 7 DELIVERY Customer Note: If you ha ve purchased this product without complete assembly and instruction by your retailer , it is your responsibility to: 1.
GB - 8 SAFETY DECALS AND LOCATIONS AL WA YS replace missing or damaged Safety Decals. Refer to fi gure below f or Safety Decal locations. 1. D ANGER! 2. W ARNING! DANGER / PELIGRO ROT ATING PARTS Stop engine & remove ignition key before clearing.
GB - 9 3. D ANGER! 4. HO T SURF A CES! ASSEMBLY SAF ETY RULES Read, understand, and follo w all safety practices in Owner/Operator Manual bef ore beginning assembly . F ailure to follo w instructions could result in personal injur y and/ or damage to unit.
GB - 10 Nev er direct discharge tow ards persons or proper ty that may be injured or damaged b y thrown objects. Use extreme caution on g rav el surfaces . Stay aler t for hidden hazards or traf fi c. Adjust Runners so Scraper Blade does not contact gra vel.
GB - 11 Spark Arrester This product is equipped with an internal combustion type engine . DO NO T use unit on or near any unimprov ed, f orest-cov ered or brush covered land unless e xhaust system is equipped with a spark arrester meeting applicable local, state or f ederal la ws.
GB - 12 T ools Required: • Pliers • Open-End Wrenches: 3/8, 7/16, 1/2, 9/16" and/or Adjustable Wrench • Tire Gauge ASSEMBL Y Handlebar and Shift Rod 1. Remo ve lo wer wing knobs on handlebar assembly (Figure 4). 2. Remo ve upper wing nut and bolt on shift rod.
GB - 13 Check Function of Dual Handle Interlock (932101, 309) Without the engine running, press down (engage) both clutch lev ers. Release attachment clutch lev er . Attachment clutch should remain engaged until traction clutch lev er is released, then both clutches must disengage.
GB - 14 Run in Attachment Belt 1. Start unit in a well-ventilated area according to Star ting and Shut-Off in Operation . 2. Engage attachment clutch le v er and run attachment for about 15 min utes. 3. Stop unit, w ait for all mo ving par ts to stop, and remov e spark plug wire.
GB - 15 Choke Control Knob 1. Choke Closed position: chokes off air to engine f or easier star t. 2. Choke Open position: allows f or normal operation. IMPORT ANT : Gradually open choke after engine star ts. Throttle The throttle controls the engine speed.
GB - 16 PRE-START 1. Frozen Impeller IMPORT ANT : Bef ore star ting engine, check impeller to be sure it is not frozen. T o check impeller : 1. With k ey in “ Stop ” position, squeeze Attachment Clutch Lev er to Engaged position. 2. Pull Recoil Starter Handle.
GB - 17 Electric Start (120V or 240V) (932035, 101, optional on 309, 503) 1. Connect e xtension cord to prongs on star ter . IMPORT ANT : Pre vent damage to unit. Know voltage of y our star ter and only use matching outlets. 2. Plug e xtension into: 240V 3-wire, grounded outlet.
GB - 18 Ariens Dealers will provide any service or adjustments which may be required to k eep your unit operating at peak ef fi ciency . Should engine service be required, contact an Ar iens dealer or an authorized engine manuf acturer's service center.
GB - 19 CLEAN ENGINE Refer to Engine Man ual for detailed instructions. CHECK ENGINE OIL The engine crankcase oil should be check ed ev ery 5 hours of operation. Oil le vel MUST be maintained in safe oper ating range on dipstick at all times or engine damage will result (See Engine Manual).
GB - 20 DISCHARGE CHUTE DEFLECTOR De fl ector must sta y in selected position while throwing snow . T o adjust, loosen then retighten hardware to desired de fl ector drag f orce (Figure 9). DISCHARGE CHUTE If chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on spring (Figure 10).
GB - 21 RUNNERS Runners should be adjusted (Figure 11) as conditions require. 1. P osition unit on a hard, fl at, smooth lev el surface . 2. Adjust runners by inserting a spacer of desired thickness under center of scraper blade , loosen runner hardware, slide runners to fl at surface.
GB - 22 SPEED SELECTOR ADJUSTMENT T o adjust (Figure 13): 1. Remo ve hair pin from adjustment piv ot pin. 2. Pull shift rod and adjustment piv ot pin out of speed selector lev er . 3. Place the speed selector in the f astest rev erse speed position. 4.
GB - 23 Replace Attachment Drive Belt 1. Place ne w belt onto lower pulle y and while holding brake out of w ay , tip unit together . 2. Secure b lower housing to fr ame with cap screws . 3. Place belt onto engine shea ve . 4. Mak e sure engine sheav e and attachment pulley align.
GB - 24 T RACTION DRIVE BELT REPLACEMENT NO TE: Housing and frame must be tipped apar t and attachment drive belt remov ed from engine sheav e in order to change traction drive belt (Figures 14 & 15). 1. Remo ve attachment drive belt (See Remov e Attachment Drive Belt ).
GB - 25 8. Chec k belt fi nger clearance. With clutch lev er engaged, belt fi ngers should be 1/16 – 1/8 in (1.6-3 mm) from belt. Adjust belt fi ngers as necessar y . 9. Replace belt co ver . 10. Chec k that auger/impeller stops within 3 seconds after attachment clutch/ impeller brake bail is released.
GB - 26 FRICTION DISC REPLACEMENT (932035, 503) Remove Friction Disc (Figure 19): 1. Shut off engine , remov e key , disconnect spark plug wire and allow unit to cool completely . 2. Tip the unit up onto front housing on a lev el surf ace. 3. Remo ve loc knut and bolts from wheel axles and remov e wheels.
GB - 27 FRICTION DISC REPLACEMENT (932101, 309) Remove Friction Disc (Figure 20): 1. Shut off engine , remov e key , disconnect spark plug wire and allow unit to cool completely . 2. Tip the unit up onto front housing on a lev el surf ace. 3. Remo ve loc k pins from wheel axles and remov e wheels.
GB - 28 9. Reinstall tires with clip pins . 10. Set unit upright. 11. Replace spark plug wire on spark plug. SHORT T ERM IMPORT ANT : NEVER spra y unit with high pressure water or store unit outdoors. Run with attachment clutch engaged a fe w minutes after each use to free unit of any loose or melting snow .
GB - 29 T o obtain a complete par ts manual, fi nd your model and serial number . Then go to www .ar iens.com or call 1-800-678-5443. * A vailab le in CE countries. Small rubber beads collect in frame 1. F r iction disc wear . 1. Normal friction disc wear .
GB - 30 SPECIFICATIONS Model Number 932309 932101 932503 932035 Description 824 824 724 724 Engine - T ecumseh HMSK80- 155700W HMSK80- 155699W OHSK70- 72507E OHSK70- 72517E P ower Max - HP (Kw/min -1 ) 8 (5.97) 7 (5.22) F ast Idle Speed-RPM (min -1 ) 3600 ± 150 Displacement - in.
GB - 31 3 Y ear Limited Sno-Thro W arranty Ariens Company warrants to the original purchaser that consumer products manufactured by Ariens Company will be free from def ects in material and workmanshi.
Ariens Company 655 West Ryan Str eet P .O. Box 157 Brillion, WI 54110-0157 920-756-2141 Fax 920-756-2407 www .ariens.com.
Een belangrijk punt na aankoop van elk apparaat Ariens 932035 - 724 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ariens 932035 - 724 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ariens 932035 - 724 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ariens 932035 - 724 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ariens 932035 - 724 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ariens 932035 - 724 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ariens 932035 - 724 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ariens 932035 - 724 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
