Gebruiksaanwijzing /service van het product LM21S van de fabrikant Ariens
Ga naar pagina of 28
Owner/Operator Man ual Models 91 1 102 - PRO21SCH 91 1 132 - LM21 91 1 133 - LM21S 91 1 134 - LM21SW 91 1 139 - LM21S 91 1 141 - PRO21SCH W alk Behind Lawn Mower 01270600C 2/06 Printed in USA T ransfer model & serial number label from product registration here.
GB - 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . 8 Controls a nd Fe a t ure s . . . . . . . . . . . . . 9 Operati on . . . . . . . . . . . . . . . . . . . . . . . 10 Mainten ance.
GB - 3 PRODUCT REGISTRA TION The Ariens d ealer must register the product at the time of purchase. Registering the product will help the company process warranty claims or contact you with the latest service information.
GB - 4 NOT A TIONS NOTE: General reference information for proper operation and maintenance practices. IMPORT ANT : S pecific proc ed ures or information required to prevent damage to unit or attachment. PRACTICES AND LA WS Practice usual and customary safe working precautions, for the benefit of yourself and others.
GB - 5 2. DANGER! KEEP HANDS AND FEET A W A Y Do not operate mower unless guards are in operating position or bagger is attached. 3. CAUTION! • Bag is subject t o wear and deterioration. • Check bag frequently , replace when necessary . • Use original bag to comply with s afety specifications.
GB - 6 Keep safety devices or guards in place and functioning properly . NEVER m odify or remove safety devices. Read, understand, and follow all instruct ions in the manual and on the machine bef ore starting. Understand: • How to operate all controls • The functions of all controls • How to STOP in an em ergenc y .
GB - 7 Keep the nozzle in contact with the rim of the fuel tank or container opening at al l times until fueling is complete. Do not use a nozz le lock- open device. Check fuel supp ly before starting engine. DO NOT fill gasoline tank indoors, when engine is running, or while engine is h ot.
GB - 8 CARTON CONTE NTS ASSEMB L Y 1. Unfold and adjust handlebar . See HANDLEBAR HEIGHT on page 18 . NOTE: DO NOT bend the speed control rod (if equipped) when unf olding the handlebars. 2. F ill engine crankcase with oil. See engine manual. 3. Set -up mowe r for bagging, side discharge or m ulching.
GB - 9 1. Engine/Blade Control 2. Wheel Drive Control (91 1 102, 133, 134, 139, 141) 3. Adjustable and Folding Handlebars 4. Swivel Whee l Lock (91 1134) 5. Gra ss Bag 6. Rear Do or 7. Fuel T ank and Cap 8. Fuel Shut off V alve (9 1 1 102, 141) 9. Height Adjustment Pins (91 1 134) 10.
GB - 10 CONTROLS AND FEA TURES See Figure 6 for locations. Engine/Blade Control The engine/blade control must be held against the handlebar to start the engine and blade. Engine/blade control feature on mower stops engine and blade within 3 secon ds whenever operator releases handlebar .
GB - 1 1 Swivel W heel Models (91 1 134) T o change front wheel cutting height , insert height adjuster pin into t he holes that match the desired cutting height and fasten with key ring (Figure 8). T o change rear wheel cutting height, move cutting height levers one notch at a t ime to set the desired c utting height.
GB - 12 S peed Control (se lf-propelled models) S peed control rod changes the mower ’s forward travel speeds. High –Push rod all the way forward. Low –Pull rod all t he way rearward. S tart mowing slowly and use speed control rod to gradually increase speed to a safe, comfortable walking pace.
GB - 13 91 1 141 Fuel shutoff valve open. Fuel shutoff valve closed. FILLING THE FUEL T ANK T o add fuel to fuel tank: 1. Put unit in open or well -ventilated area. 2. St op engine and allow t o cool. 3. Clean fuel cap and surrounding area. 4. Remove cap.
GB - 14 EMERG ENC Y STOPP ING T o stop the m ower in an emergency: 1. Release the engine/blade control. 2. Release the wheel drive control ( self- propelled models). 3. Allow all m oving parts to stop before leaving operator ’s position. ST ARTING AND SHUT OFF See Figure 6 for all Controls and Features.
GB - 15 Ariens Dealers will provide any service, parts or adjustments which may be required to keep your unit operating at peak ef ficiency . Should engine require se rvice, contact an Ariens Dealer or an authorized engine manufacturer's service center .
GB - 16 T o inst all blade: 1. Replace blade, flat washer , lock washer and bolt on shaft. 2. T orque bolt to 37.5 - 50 lbf-ft (51-68 N•m) (bolt s hould fully compres s lock washer). 3. Connect spark plug wire. Sharpen the Mowe r Blades 1. Remove mower blade from unit.
GB - 17 CHECK DRIVE BEL T (self- propelled m odels) Check drive belt and replace if w orn or damaged. See DRIVE BEL T REPLACEME NT (self-propelled models) on page 19. CHECK F ASTENERS Check all fasteners for proper t ightness. Pay special attention to blade hardware and all guards, shields and safety devices.
GB - 18 SER VICE PO SITION Put unit into se rvice position for eas y access to underneath the deck. 1. Place unit on a flat, level surface. 2. Disconnect spark plug wire. 3. Remove fuel cap, place a piece of plastic bag over the opening and tighten cap securely .
GB - 19 DRIVE BEL T REPLACEMENT (self-pro pelled mode ls) T o remove drive belt : 1. Disconnect spark plug wire. 2. Set the right rear wheel to its lowest cutting height, and the left rear wheel to the third cutting height. This position provides clearance between friction disc and drive sheav e.
GB - 20 5. Tighten upper cable nut until bracket is secure between cable nuts. 6. Engage engine/blade control. Measure distance between middle of z -bend and cable bracket. Measuremen t should be as shown be low . 7. For Honda engine s : Disengage engine/blade control and make sure there is adequate freeplay in the cable.
GB - 21 T o decrease the gap between the friction disc and the aluminum drive plate: 1. Loosen the upper cable nut on the wheel drive control cable, and then tighten t he lower cable nut against the adjuster bracket. See Figure 18. 2. Chec k the adjustment and readjust as needed.
GB - 22 IMPORT ANT : NEVER spray unit with high- pressure wa ter or store unit outdoors. S tore mower in a coo l, dry , protected loc ation. Cleaning Clean unit thoroughly with mild soap and low pressure water . Brush off dirt and debris from all surfaces.
GB - 23 Wheel drive does not engage (Self - Propelled models) 1. W heel drive control n ot engaged. 2. Drive belt out of position. 3. Drive belt worn or damaged. 4. Rear wheels at different cutting heights. 5. Idler spring detached. 6. W heel drive control cable detached or broken.
GB - 24 SPECIFICA TIONS Model Number 91 1 102 91 1 132 911 133 Description LM21SCH LM21 LM 21S Length - in. (cm ) 61.5 (156) Height - in. (cm) 38 (96.5) Width - in. (cm) 23 (58.4) Actual Weight - lbs (kg) 97 (44) 93 (42.2) 109 (49.4) Cutting Width- in.
GB - 25 SPECIFICA TIONS Model Number 91 1 134 91 1 139 911 141 Description LM21SW LM 21S LM21SCH Length - in. (cm ) 61.5 (156) Height - in. (cm) 38 (96.5) Width - in. (cm) 23 (58.4) Actual Weight - lbs (kg) 125 (56.7) 97 (44) 109 (49.4) Cutting Width- in.
Ariens Com pany • 6 55 W . Ryan S t, P .O. Box 1 57 • Brillion, WI 541 10-0157• (920 ) 756-2141 • www .ariens.com AL W2-62905 Ariens Limited Warranti es 2-Year L imited Law n and Garden Consum.
Ariens Com pany • 6 55 W . Ryan S t, P .O. Box 1 57 • Brillion, WI 541 10-0157• (920 ) 756-2141 • www .ariens.com AL W2- 62905 Exceptions, L imitations, Ex clusions These warran tie s are subj.
Ariens Company 655 West Ryan St reet P .O. Box 157 Brillion, W I 541 10-0 157 920-756-2141 Fax 920-756-2407 www .ariens.com.
Een belangrijk punt na aankoop van elk apparaat Ariens LM21S (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ariens LM21S heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ariens LM21S vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ariens LM21S leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ariens LM21S krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ariens LM21S bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ariens LM21S kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ariens LM21S . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
