Gebruiksaanwijzing /service van het product 12211 van de fabrikant MTD
Ga naar pagina of 48
Models 12211 – Recoil Start 12212 – Electric Start OWNER’S MANUAL 7 HP PONY ® REAR-TINE TILLER • Safety • Assembly • Features and Controls • Operation • Maintenance • Parts List GAR.
2 T able of Contents SECTION 1: SAFETY ........................................... 3 Safety Decals .................................................................... 5 SECTION 2: ASSEMBLY ....................................... 6 Attach Handlebars..
3 TRAINING 1. Carefully read this Owner ’ s Manual, the sepa- rate Engine Owner ’ s Manual, and any other literature you may receive. Be thoroughly familiar with the controls and the proper use of the tiller and its engine. Know how to stop the unit and disengage the controls quickly.
7. Take all possible precautions when leaving the machine unattended. Stop the engine. Remove ignition key on electric start models. Disconnect spark plug wire and move it away from the spark plug.
Section 1: Safety 5 4. To reduce the chances of a fire hazard, keep the engine free of grass, leaves, or excessive grease. 5. Store gasoline in a cool, well-venti- lated area, safely away from any spark- or flame-producing equipment. Store gasoline in an approved container, safely away from the reach of children.
INTRODUCTION Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you read this Section in its entirety before beginning assembly. INSPECT UNIT Inspect the unit and carton for damage immediately after delivery.
3. With forward clutch cable (N, Figure 2-4) on inside of handlebar, position handlebar ends on outside of the two mounting tabs (M, Figure 2-3) on trans- mission top cover. NOTE: The curved handlebar height adjustment bracket appears as shown in C, Figure 2-3 for non-electric start units.
3. The cable is pre-adjusted at the factory, but must be checked for correct tension as explained next: The forward clutch spring coil (between points “ A ” in Figure 2-9) measures 2" in length when neither Forward Clutch Control Lever is pulled up.
9 STEP 7: A TT ACH WHEEL GEAR LEVER 1. Insert the Wheel Gear Lever (P, Figure 2-13) up through the slot in the control panel that is labeled “ WHEEL GEAR.
10 Section 2: Assembly Electric Start Assembly Steps The following steps explain how to prepare and install the battery. FOR YOUR SAFETY, CAREFULLY FOLLOW ALL STEPS AND OBSERVE ALL ACCOM- PANYING SAFETY MESSAGES. Before beginning, check that you have received the following items (see Figure 2-16): 1.
11 Section 2: Assembly B. To Charge the Battery: To obtain maximum battery life, charge the battery using the following method until all cells are gassing freely. A battery is gassing freely when the surface of the electrolyte is covered with tiny bubbles.
Section 2: Assembly 4. Check the tightness of the upper mounting screw that secures the negative cable and starter solenoid to the battery post. See Figure 2-20. Scrape away any paint between the cable and the screw as the paint can prevent a good electrical ground.
13 Before operating your machine, care- fully read and understand all safety, controls and operating instructions in this Manual, the separate Engine Owner ’ s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injury.
REVERSE CLUTCH CONTROL The Reverse Clutch Control (C, Figure 3- 1) controls the engagement of reverse drive to the wheels and tines. The revers- ing feature is used for maneuvering the tiller only – never engage the tines in the ground while going in the reverse direction.
Section 3: Features and Controls ENGINE CONTROLS Refer to the engine manufacturer ’ s Engine Owner ’ s Manual (included in the tiller lit- erature package) to identify the controls on your engine. The following two con- trols are used when stopping or starting the engine.
16 Figure 4-1: Location of main tiller controls. Section 4 INTRODUCTION Read this Section of the manual thor- oughly before you start the engine. Then, take the time to familiarize yourself with the basic operation of the tiller before using it in the garden.
17 Section 4: Operation ST ARTING THE ENGINE The following steps describe how to start and stop the engine. Do not attempt to engage the tines or wheels until you have read all of the operating instruc- tions in this Section.
18 Section 4: Operation 4. For forward motion of the wheels and tines: (a) Pull one or both of the Forward Clutch Control Levers up and hold them against the handlebars. To stop forward motion of the wheels and tines, release the levers. (b) As the tiller moves forward, relax and let the wheels pull the unit along while the tines dig.
19 Section 4: Operation T illing T ips & T echniques Let the tiller do the work • While tilling, relax and let the wheels pull the tiller along while the tines do the digging. Walk on the side that is not yet finished (to avoid making foot- prints in the freshly tilled soil) and lightly, but securely grip the handlebar with just one hand.
20 Section 4: Operation T illing T ips & T echniques Clearing the tines The tines have a self-clearing action which eliminates most tangling of debris in the tines. However, occasionally dry grass, stringy stalks or tough vines may become tangled.
21 Section 4: Operation POWER COMPOSTING Power composting simply means tilling under and burying in the soil all manner of organic matter such as crop residues, leaves, grass clippings and cover crops. This material will decompose during the non-growing season and add important natural nutrients to the soil.
22 Section 5 Maintenance REQUIRED MAINTENANCE SCHEDULE Before Every Every As PROCEDURE Each 10 30 Noted Use Hours Hours Check engine oil level • And every 5 operating hours Clean engine • ▲ Chec.
23 Section 5: Maintenance W ARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on elec- tric start models.
24 Section 5: Maintenance W ARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on elec- tric start models.
25 Section 5: Maintenance W ARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on elec- tric start models.
CHECKING AND ADJUSTING TENSION ON CLUTCH BEL TS Maintaining correct belt tension is impor- tant to good tilling performance and long belt life. A loose belt will slip on the engine and transmission pulleys and cause the tines and wheels to slow down – or stop – even though the engine is running at full speed.
2. The coiled part of the forward clutch spring (E, Figure 5-10) measures 2" in length when the Forward Clutch Control levers are not pulled up. Pull either Forward Clutch Control Lever up against the handlebar and measure the length of the coil on the forward clutch spring.
Removing Forward Clutch Belt 1. Stop engine, allow it to cool and dis- connect spark plug wire before working near belts. Also remove ignition key on electric start models. 2. Remove the two nuts (C, Figure 5-13) and remove the belt cover. 3. Move the reverse clutch belt (B, Figure 5-16) out of the way.
pull down on the belt and roll it onto the large, forward-most groove of the trans- mission pulley (P, Figure 5-20). 7. Reinstall the belt cover. 8. Test for correct tension on the forward clutch belt (see Checking Forward Belt Tension) .
Section 5: Maintenance W ARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on elec- tric start models.
31 Section 5: Maintenance W ARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on elec- tric start models.
32 TROUBLESHOOTING Before performing any corrections, refer to the appropriate information in this Manual, or in the Engine Owner ’ s Manual, for the correct safety precautions and operating or maintenance procedures. Contact your local authorized Engine Service Dealer for engine service.
33 P ARTS LIST Models 12211 and 12212 HOOD, BRACKET and DEPTH REGULA TOR 1 1917605 Tine Hood (Incl. hood flap and Ref.17) ............................................ 1 2 1100243 Lockwasher, 3/8.................................. 2 3 2527 Bracket – hood & depth regulator (Incl.
34 P ARTS LIST Models 12211 and 12212 HANDLEBAR ASSEMBL Y and CONTROL LEVERS 10 See page 36, Ref. 47, for attach- ment screw..
35 Models 12211 and 12212 P ARTS LIST REF. PART No. No. DESCRIPTION QTY. REF. PART No. No. DESCRIPTION QTY. 1 1918811 Handlebars (Incl. Refs. 2, 3 & 3A) ....... 1 2 9126 Grip ..................................................... 2 3 1918770 Decal, Control Panel .
P ARTS LIST Models 12211 and 12212 Reverse Clutch Cable 1 2 6 5 7 3 4 13 14 15 16 17 16 49 21 25 24 35 45 46 20 49 50 51 43 43 44 37 47 37 40 42 48 41 44 38 40 39 20 23 8 12 26 27 3 28 29 30 31 9 22 1.
37 Models 12211 and 12212 P ARTS LIST ENGINE, SUPPORT BRACKETS, PULLEYS, BEL TS, BEL T COVER 1 ** Engine – standard recoil start ............ 1 ** Engine – electric start ........................ 1 2 1917326 Bracket, Clutch Cable .................
38 Models 12211 and 12212 P ARTS LIST TRANSMISSION HOUSING, COVERS, SEALS, GASKETS, PLUGS NOTE 1: These screws are a special sealing screw that cannot be reused without risking the loss of transmission oil. If these screws are loosened or removed, they must be replaced with new screws.
39 P ARTS LIST Models 12211 and 12212 MAIN DRIVE SHAFT 1 1714 Bearing, Tapered Roller with Race .... 1 2 20718 Spur Gear ..............................
40 Models 12211 and 12212 P ARTS LIST WHEEL SHAFT , ECCENTRIC SHAFT and TILLER SHAFT ASSEMBLIES REF. PART No. No. DESCRIPTION QTY. REF. PART No. No. DESCRIPTION QTY. 1 9621 Oil Seal .............................................. 2 2 9511 Retaining Ring (heavy-duty, external) 2 3 1166-1 Shim, 1-1/64 I.
41 P ARTS LIST Models 12211 and 12212 1 1100043 Hex Hd. Screw, 3/8-16 x 1-1/4* .......... 16 2 1270-2A Bolo Tine-single. Right hand tine used on left side of tiller. (Incl. two ea. Refs. 1 and 3) ..................... 8 3 1733398 Hex Locknut, 3/8-16 .
42 P ARTS LIST Models 12211 and 12212 ELECTRIC ST ART ASSEMBL Y 30 31.
43 Models 12211 and 12212 P ARTS LIST ELECTRIC ST ART ASSEMBL Y 1 96512 Battery, 12 Volt, 9 Amp (Incl. Ref. 7) ........................................... 1 2 9462 Battery Cap (yellow) .......................... A/R 2A 9248 Battery Cap (white) .......
44 P ARTS LIST Models 12211 and 12212 ROW MARKER A TT ACHMENT ROW MARKER ATTACHMENT – PART # 12589 (Complete – Attaches to Furrower Attachment) MAIN SUPPORT/YOKE ASSEMBLY PART # 1904522001 DET AIL.
45 Models 12211 and 12212 P ARTS LIST ROW MARKER A TT ACHMENT & BUMPER A TT ACHMENT Row Marker Attachment (option) – Part #12589 1 1904522001 Main Support & Yoke Assy – complete. (Incl. Ref. No.'s 10,11,12,13,14,15,16,17 & 18)....
46 Models 12211 and 12212 P ARTS LIST HILLER/FURROWER A TT ACHMENT HILLER/FURROWER – PART #12579 (Viewed from front of tiller) 1 1900771001 Furrower Blade .................................. 1 2 1186098 Carriage Bolt, 5/16-18 x 3/4 .............. 4 3 1177548 Star Washer, External Tooth, 5/16.
47 NOTES.
1905624 (2/01) Printed in U.S.A. © 2001 Garden Way Incorporated CUSTOMER SERVICE INFORMA TION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory so that we can provide you with warranty benefits and informational bulletins.
Een belangrijk punt na aankoop van elk apparaat MTD 12211 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen MTD 12211 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens MTD 12211 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding MTD 12211 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over MTD 12211 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van MTD 12211 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de MTD 12211 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met MTD 12211 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
