Gebruiksaanwijzing /service van het product E760 van de fabrikant MTD
Ga naar pagina of 28
IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y MTD PR ODUCTS INC. P .O . BO X 368022 CLEVELAND , OHIO 44136-9722 MODELS E740 E760 Warning: This unit is equipped with an internal combust.
2 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER.
3 • If the snow thrower should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. • Stop engine whenever you leave the operating position, before unclogging the collector/impeller housing or discharge guide, and making any repairs, adjustments, or inspections.
4 SECTION 2: FINDING YOUR MODEL NUMBER This Operators Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain your snow thrower.
5 SECTION 4: CONTENTS OF HARDWARE PACK La y out the hardw are according to the illustration for identification purposes. P ar ts are illustrated appro ximately one-half size . P ar t numbers are shown in parentheses . (Hardware pac k may contain e xtra items which are not used on your unit.
6 SECTION 5: ASSEMBLY INSTRUCTIONS NO TE: Ref erence to right or left side of the snow thro wer can be determined from behind the unit in the operating position. Figure 2 Figure 3 Figure 4 UNP A CKING 1. Remove staples or break glue on the top flaps of the carton.
7 Figure 5 Figure 6 Figure 7 Figure 8 A TT A CHING THE CHUTE ASSEMBL Y (Hard ware B) 1. Place chute assembly over chute opening, with the opening in the chute assembly facing the front of the unit. 2. Place chute flange keepers beneath lip of chute assembly with the flat side down.
8 IMPORTANT: Attach the shift rod and clutch cables as follows. THEN CHECK THE ADJUSTMENTS AS INSTRUCTED, AND MAKE ANY FINAL ADJUSTMENTS NECESSARY BEFORE OPERATING YOUR SNOW THROWER. Failure to follow the instructions may cause damage to the snow thrower.
9 4. Attach track control cable to track control handle by inserting cable ball into slot on track control handle. Pull cable down and up until it snaps into front of track control handle. Repeat on other side. 5. Secure the track control cables to the inside of the lower handle using the cable ties provided.
10 SECTION 6: CONTROLS Figure 14 SHIFT LEVER (See figure 14) The shift lever is located in the center of the handle panel. The shift lever may be moved into one of eight positions. Run engine with throttle in the fast position. Use the shift lever to determine ground speed.
11 SECTION 7: OPERATION GAS AND OIL FILL-UP Service the engine with gasoline and oil as instructed in the separate engine manual packed with your snow thrower. Read instructions carefully. WARNING: Ne v er fill fuel tank indoors, with engine running or while engine is hot.
12 T O ST OP ENGINE 1. Run engine for a few minutes before stopping to help dry off any moisture on the engine. 2. To help prevent possible freeze-up of starter, proceed as follows. Connect power cord to switch box on engine, then to 120 volt AC receptacle.
13 SECTION 8: ADJUSTMENTS WARNING: NEVER attempt to clean chute or make an y adjustments while engine is running. CHUTE ASSEMBL Y ADJUSTMENT The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to the Control section of this manual.
14 SECTION 9: LUBRICATION WARNING: Disconnect the spark plug wire and ground a gainst the engine before perf orming any lubrication or maintenance. ENGINE Refer to engine manual for all engine lubrication instructions.
15 SECTION 10: MAINTENANCE WARNING: Disconnect the spark plug wire and ground a gainst the engine before perf orming any repairs or maintenance. A UGER BEL TS 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws.
16 Figure 22 CHANGING THE FRICTION WHEEL RUBBER The rubber on the friction wheel is subject to wear and should be checked after 25 hours of operation, and periodically thereafter. Replace the friction wheel rubber if any signs of wear or cracking are found.
17 SECTION 11: OFF-SEASON STORAGE WARNING: Never store engine with fuel in tank indoors or in poorl y ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater , clothes dryer or other gas appliance.
18 SECTION 12: TROUBLE SHOOTING GUIDE For repairs beyond the minor adjustments above, contact your local authorized service dealer. T rouble P ossible Cause(s) Corrective Action Engine f ails to star t Fuel tank empty , or stale fuel. Block ed fuel line.
19 Gear Assembly Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 618-0123 Housing-L.H. 1 11 721-0327 Seal-Oil 1 2 618-0124 Housing-R.
20 Handle Assembly.
21 Handle Assembly Ref. No. P art No. Description Qty . Ref. No. P art No. Description Qty . 1 684-0008 Arm-Shift 1 34 741-0475 Bushing-Plastic 1 3 684-0103 P anel-Handle 1 35 747-0798A Rod-Shift 1 4 684-0036 Handle-Engagement-R.H. 1 36 747-0877 Rod-Cam 2 5 684-0037 Handle-Engagement-L.
22 Blower Housing 26’’ Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 05931 Housing-Bearing 1 19 731-1379 Adapter-Chute 1 2 605-5193 Spiral Assemb ly-L.
23 Track and Frame.
24 Track and Frame.
25 Track and Frame Ref. No. P art No. Description Qty . Ref. No. P art No. Description Qty . 1 611-0053 Axle Assembly 2 45 732-0209 Spring 2 2 618-0043 Dog Assembly-R.
26 Engine and V-Belts Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 05896A Brac ket-Idler 1 17 736-0331 W asher-Bell 1 2 629-0071 Cord-Extension 110V 1 18 736-0505 W asher-.
27 George.
28 MANUF A CTURER’S LIMITED W ARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.
Een belangrijk punt na aankoop van elk apparaat MTD E760 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen MTD E760 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens MTD E760 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding MTD E760 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over MTD E760 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van MTD E760 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de MTD E760 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met MTD E760 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
