Gebruiksaanwijzing /service van het product GS110TP-100NAS van de fabrikant NETGEAR
Ga naar pagina of 32
202-10596-01 March 2010 v1.0 NETGEAR , Inc. 350 East Plumeria Drive San Jose, California 95134 USA GS110TP Hardware Installation Guide.
ii v1.0, March 2010 © 2010 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR, the NETGEAR logo, and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
Contents iii v1.0, March 2010 Contents GS110TP Hardware Installation Guide About This Manual Conventions, Formats, and Scope .................................................................................... v How to Print this Manual ..............
iv Contents v1.0, March 2010 Chapter 4 Installation Step 1: Preparing the Site .............................................................................................. 4-1 Step 2: Installing the Switch ...........................................
v v1.0, March 2010 About This Manual The NETGEAR ® ProSafe TM GS110TP Hardware Installation Guide describes how to install and power on the GS110TP Smart PoE Switch. The information in this manual is intended for readers with intermediate computer and Internet skills.
Danger: This is a safety warning. Failure to take heed of this notice may result in personal injury or death. GS110TP Hardware Installation Guide vi About This Manual v1.
1-1 v1.0, March 2010 Chapter 1 Introduction Congratulations on the purchase of your NETGEAR GS110TP Smart PoE Switch. The GS110TP Smart PoE Switch is a supplement to the Gigabit Advanced Smart Switch family. Available as a desktop or wall-mountable switch, the GS110TP Smart PoE Switch is not intended to be rack- mountable.
GS110TP Hardware Installation Guide 1-2 Introduction v1.0, March 2010 The GS110TP Smart PoE Switch is a free-standing switch. It is IEEE-compliant and offers low latency for high-speed networking. All ports can automatically negotiate to the highest speed.
GS110TP Hardware Installation Guide Introduction 1-3 v1.0, March 2010 • Standard NETGEAR 1xx series chassis. • NETGEAR Green product features. • External 48V/1.25A PA. PoE Features The GS110TP Smart PoE Switch supports IEEE 802.3af PSE features: • Ports 1 through 8 support IEEE 802.
GS110TP Hardware Installation Guide 1-4 Introduction v1.0, March 2010 Package Contents Figure 1-1 shows the package contents of the NETGEAR GS110TP Smart PoE Switch.
2-1 v1.0, March 2010 Chapter 2 Physical Description This chapter describes the NETGEAR GS110TP Smart PoE Switch hardware features. Topics include: • GS110TP Front and Back Panel Configuration • LE.
GS110TP Hardware Installation Guide 2-2 Physical Description v1.0, March 2010 • Power and Status LED • PoE Max LED Figure 2-2 illustrates the NETGEAR GS110TP Smart PoE Switch back panel. Power Connector Figure 2-2 The back panel contains the following: • A DC input for the supplied 48V/1.
GS110TP Hardware Installation Guide Physical Description 2-3 v1.0, March 2010 System LEDs The following table describes the system LED designations. Table 2-2. System LEDs LED Designation Power/Status LED • Solid Green = Power is supplied to the switch and the switch is operating normally.
GS110TP Hardware Installation Guide 2-4 Physical Description v1.0, March 2010 To simplify the procedure for attaching devices, all RJ-45 ports support Auto Uplink. This technology allows attaching devices to the RJ-45 ports with either straight-through or crossover cables.
3-1 v1.0, March 2010 Chapter 3 Applications Your NETGEAR GS110TP Smart PoE Switch is designed to provide flexibility in configuring your network connections. It can be used as a stand-alone device or with 10 Mbps, 100 Mbps, and 1000 Mbps hubs and switches.
GS110TP Hardware Installation Guide 3-2 Applications v1.0, March 2010.
4-1 v1.0, March 2010 Chapter 4 Installation This chapter describes the installation procedures for your NETGEAR GS110TP Smart PoE Switch. Switch installation involves the following steps: Step 1: Prep.
GS110TP Hardware Installation Guide 4-2 Installation v1.0, March 2010 Step 2: Installing the Switch The GS110TP Smart PoE Switch can be used on a flat surface or mounted on the wall. Installing the Switch on a Flat Surface The switch ships with four self-adhesive rubber footpads.
GS110TP Hardware Installation Guide Installation 4-3 v1.0, March 2010 Step 3: Checking the Installation Before applying power to the switch, perform the following: • Inspect the equipment thoroughly. • Verify that all cables are installed correctly.
GS110TP Hardware Installation Guide 4-4 Installation v1.0, March 2010 Connect each PC to an RJ-45 network port on the Switch front panel ( Figure 4-1 ). Use Category 5 (Cat5) Unshielded Twisted-Pair (UTP) cable terminated with an RJ-45 connector to make these connections.
Note: When the device powers up, there is a default IP address already configured on the device. The default IP address is 192.168.0.239 and subnet mask 255.
GS110TP Hardware Installation Guide 4-6 Installation v1.0, March 2010.
Troubleshooting A-1 v1.0, March 2010 Appendix A Troubleshooting This chapter provides information about troubleshooting the NETGEAR Smart Switch. Topics include the following: • Troubleshooting Chart • Additional Troubleshooting Suggestions Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems.
GS110TP Hardware Installation Guide A-2 Troubleshooting v1.0, March 2010 Additional Troubleshooting Suggestions If the suggestions in Troubleshooting Chart do not resolve the problem, refer to the troubleshooting suggestions in this section.
GS110TP Hardware Installation Guide Troubleshooting A-3 v1.0, March 2010 Auto-Negotiation The RJ-45 ports negotiate the correct duplex mode and speed if the device at the other end of the link supports auto negotiation.
GS110TP Hardware Installation Guide A-4 Troubleshooting v1.0, March 2010.
Technical Specifications B-1 v1.0, March 2010 Appendix B Technical Specifications Network Protocol and Standards Compatibility IEEE 802.3i 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x flow control IEEE 802.3z 1000BASE-X IEEE 802.
GS110TP Hardware Installation Guide B-2 Technical Specifications v1.0, March 2010 Interface Eight RJ-45 connectors for 10BASE-T, 100BASE-TX, and 1000BASE-T (Auto Uplink™ on all ports) Two SFP slots .
GS110TP Hardware Installation Guide Technical Specifications B-3 v1.0, March 2010 Electromagnetic Emissions FCC Class B CE Class B: Includes EN55022 (CISPR 22), 55024, and 50082-1 VCCI Class B C-Tick .
GS110TP Hardware Installation Guide B-4 Technical Specifications v1.0, March 2010.
Index-1 v1.0, March 2010 Index Numerics 1U 1-3 8-pin 2-3 A Applying AC Power 4-4 Auto Uplink 2-4 Auto-negotiating 1-2 Autosensing 1-2 , 2-3 B Backpressure 1-2 C Category 5 Unshielded Twisted-Pair 1-2 .
GS110TP Hardware Installation Guide Index-2 v1.0, March 2010 O Operating Conditions 4-2 Operating Environment 4-1 Operating humidity 4-2 Overview 1-1 P Package Contents 1-4 Pause Frame Flow Control 1-.
Een belangrijk punt na aankoop van elk apparaat NETGEAR GS110TP-100NAS (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen NETGEAR GS110TP-100NAS heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens NETGEAR GS110TP-100NAS vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding NETGEAR GS110TP-100NAS leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over NETGEAR GS110TP-100NAS krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van NETGEAR GS110TP-100NAS bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de NETGEAR GS110TP-100NAS kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met NETGEAR GS110TP-100NAS . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
