Gebruiksaanwijzing /service van het product 350Z (2003) van de fabrikant Nissan
Ga naar pagina of 227
Foreword Welcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. This manual was prepared to help you under- stand the operation and maintenance of your vehicle so that you may enjoy many miles of driving pleasure.
IMPORTANT INFORMATION ABOUT THIS MANUAL You will see various symbols in this manual. They are used in the following ways: WARNING This is used to indicate the presence of a hazard that could cause death or serious personal injury. To avoid or reduce the risk, the procedures must be followed precisely.
Welcome To The World Of NISSAN Your new NISSAN is the result of our dedication to produce the finest in safe, reliable and economical transportation. Your vehicle is the product of a successful worldwide company that manufactures cars and trucks in over 17 countries and distributes them in 170 nations.
NISSAN CUSTOMER CARE PROGRAM NISSAN CARES ... Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Your NISSAN dealer is always available to assist you with all your automobile sales and service needs.
Table of Contents Seats, restraints and supplemental air bag systems Instruments and controls Pre-driving checks and adjustments Heater, air conditioner and audio systems Starting and driving In case of emergency Appearance and care Maintenance and do-it-yourself Technical and consumer information Index Z 02.
1 Seats, restraints and supplemental air bag systems Seats ......................................................................................... 1-2 Front manual seat adjustment....................................... 1-3 Front power seat adjustment (if so equipped) .
WARNING I Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident you could be thrown into it and re- ceive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries.
FRONT MANUAL SEAT ADJUSTMENT WARNING I Do not adjust the driver’s seat while driving so full attention may be given to vehicle operation. The seat may move suddenly and could cause loss of control of the vehicle. I After adjustment, gently rock in the seat to make sure it is securely locked.
FRONT POWER SEAT ADJUSTMENT (if so equipped) WARNING I Do not adjust the driver’s seat while driving so full attention may be given to vehicle operation. I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls.
SEAT LIFTER (for driver’s seat) Turn the dial and adjust the angle of the seat cushion to the desired position. TILTING AND RECLINING PASSENGER’S SEAT FROM DRIVER’S SEAT The passenger’s seatba.
Adjust the head restraints so the center is level with the center of your ears. WARNING Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Do not remove them. Check the adjust- ment after someone else uses the seat.
WARNING I The supplemental front air bags ordi- narily will not inflate in the event of a side impact, rear impact, roll over, or lower severity frontal collision. Al- ways wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.
SSS0132 SSS0016 1-8 Seats, restraints and supplemental air bag systems Z 02.9.13/Z33-D/V5.0 X.
SSS0006 SSS0007 SSS0008 SSS0009 SSS0099 SSS0100 Seats, restraints and supplemental air bag systems 1-9 Z 02.9.13/Z33-D/V5.0 X.
WARNING I Never let children 12 or under ride in this vehicle. Do not attempt to hold them in your lap or arms. Some ex- amples of dangerous riding positions are shown in the previous illustra- tions.
out of the window or lean against the door. Some examples of dangerous riding positions are shown in the pre- vious illustrations. I Do not use seat covers on the front seatbacks. They may interfere with supplemental side air bag inflation. COMPONENTS OF THE SUPPLEMENTAL RESTRAINT SYSTEMS 1.
may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. They may not inflate in certain frontal collisions. Vehicle damage (or lack of it) is not always an indication of proper supplemental air bag operation.
includes changes to the steering wheel and the instrument panel as- sembly by placing material over the steering wheel pad, above the dash- board, or by installing additional trim material around the air bag system. I Work around and on the supplemen- tal front air bag system should be done by a NISSAN dealer.
collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity side impact. They are designed to inflate on the side where the vehicle is impacted. They may not inflate in certain side collisions.
seat covers, around the side air bag. I Work around and on the side air bag and curtain side-impact air bag sys- tem should be done by a NISSAN dealer. Installation of electrical equipment should also be done by a NISSAN dealer. The SRS wiring har- nesses* should not be modified or disconnected.
heard. The smoke is not harmful, but care should be taken not to inhale it as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly.
SUPPLEMENTAL AIR BAG WARNING LIGHT The supplemental air bag warning light, display- ing in the instrument panel, monitors the circuits of the supplemental front air bag, supplemental side air bag (if so equipped) and curtain side-impact air bag (if so equipped) systems, and pre-tensioner seat belt.
WARNING I Once the supplemental front air bag, side air bag or curtain side-impact air bag has inflated, the air bag module will not function again and must be replaced. Additionally, if any of the supplemental front air bags inflate, the activated pre-tensioner seat belt must also be replaced.
PRECAUTIONS ON SEAT BELT USAGE Your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced if you are wearing your seat belt and it is properly adjusted.
I Position the lap belt as low and snug as possible around the hips, not the waist. A lap belt worn too high could increase the risk of internal injuries in an accident. I Be sure the seat belt tongue is se- curely fastened to the proper buckle. I Do not wear the belt inside out or twisted.
CHILD SAFETY Children need adults to help protect them. They need to be properly restrained. WARNING I Never let children 12 or under ride in this vehicle. Do not attempt to hold them in your lap or arms. I Never let children stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving.
should choose a child restraint that fits your vehicle and always follow the manufacturer’s instructions for installation and use. Larger children Children who are too large for child restraint systems should be seated and restrained by the seat belts which are provided.
ceive neck or other serious injuries. You could also slide under the lap belt and receive serious internal inju- ries. I For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly.
Unfastening the seat belts To unfasten the belt, press the button on the buckle. The seat belt will automatically retract. Checking seat belt operation Your seat belt retractors are designed to lock belt movement using two separate methods: I when the belt is pulled quickly from the retractor.
WARNING I Only NISSAN seat belt extenders, made by the same company which made the original equipment belts, should be used with NISSAN seat belts. I Persons who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident.
possible for even the strongest adult to resist the forces of a severe acci- dent. The child could be crushed be- tween the adult and parts of the ve- hicle.
I For a front facing child restraint, check to make sure the shoulder belt does not go in front of the child’s face or neck. If it does, put the shoulder belt behind the child restraint. If you must install a front facing child re- straint in the front seat, see instruc- tions later in this section.
Anchor point location The anchor point q A is located on the luggage area floor. A flap is provided in the carpet for easy access and is marked with the label shown. If you have any questions when installing a top tether strap child restraint on the pas- senger seat, consult your NISSAN dealer for details.
child in a sudden stop or collision. Front facing If you must install a child restraint in the front seat, follow these steps: 1. Turn the air bag ON/OFF switch to the OFF position. 2. Position the child restraint on the front pas- senger seat. Move the seat to the rearmost position.
4. Pull on the shoulder belt until all of the belt is fully extended. At this time, the belt retractor is in the automatic locking mode (child re- straint mode). It reverts back to emergency locking mode when the belt is fully retracted. 5. Allow the belt to retract.
After the child restraint is removed and the seat belt is allowed to wind back into the retractor, the automatic locking mode (child restraint mode) is canceled; the seat belt only locks during a sudden stop or impact. Rear facing When you install a child restraint in the front seat, follow these steps: 1.
4. Pull on the shoulder belt until all of the belt is fully extended. At this time, the belt retractor is in the automatic locking mode (child re- straint mode). It reverts back to emergency locking mode when the belt is fully retracted. 5. Allow the belt to retract.
After the child restraint is removed and the seat belt is allowed to wind back into the retractor, the automatic locking mode (child restraint mode) is canceled; the seat belt only locks during a sudden stop or impact. Seats, restraints and supplemental air bag systems 1-33 Z 02.
2 Instruments and controls Instrument panel ..................................................................... 2-2 Meters and gauges ............................................................... 2-3 Speedometer and odometer ......................
Power windows .............................................................. 2-33 Automatic adjusting function ...................................... 2-34 Interior light ........................................................................... 2-35 Spot light .
1. Headlight and turn signal switch (P.2-21) 2. Instrument brightness control switch (P.2-23) 3. Driver supplemental air bag (P.1-6)/Horn (P.2-24) 4. Meters/gauges (P.2-3) 5. Cruise control main/set switch (P.5-15) 6. Trip computer mode/setting switch (P.
Combination meter: 1. Warning/Indicator lights 2. Turn signal/hazard indicator lights 3. Tachometer 4. Speedometer 5. Instrument brightness control switch (See “Headlight and turn signal switch” later in this section.) 6. Fuel gauge 7. Engine coolant temperature gauge 8.
Triple meter: 1. Trip computer 2. Engine oil pressure gauge 3. Volt meter SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed. Odometer/Twin trip odometer The odometer/twin trip odometer are displayed when the ignition key is in the ON position.
TACHOMETER The tachometer indicates engine speed in revo- lutions per minute (r/min). CAUTION When engine speed approaches the red zone, shift to a higher gear. Operating the engine in the red zone may cause serious engine damage. ENGINE COOLANT TEMPERATURE GAUGE The gauge indicates the engine coolant tem- perature.
FUEL GAUGE The gauge indicates the approximate fuel level in the tank. The gauge may move slightly during braking, turning, acceleration, or going up or down hill. The gauge needle is designed to move to the E (Empty) position when the ignition key is turned to the OFF position.
CAUTION I This gauge is not designed to indi- cate low engine oil level. Use the dipstick to check the oil level. (See “Engine oil” in the “8. Maintenance and do-it-yourself” section.) I If the gauge needle does not move with the proper amount of engine oil, have the vehicle checked by a NISSAN dealer.
TRIP COMPUTER The display of the trip computer is situated in the triple meter. When the ignition switch is turned to ON, the display scrolls all the modes of the trip computer and then shows the mode chosen before the ignition switch is turned OFF. Switches for the trip computer are located on the side of the combination meter panel.
temperature displayed on various signs or bill- boards. Distance to empty (dte — mile or km) The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly being calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption.
by sending a signal from a sensor that is installed in each wheel. Press the trip computer setting switch q B to change the display to F (front) or R (rear). The tire pressure sensor will activate only when the vehicle is driven at speeds above 20 MPH (32 km/h).
or Anti-lock brake warning light Low washer fluid warning light Malfunction indicator lamp (MIL) Automatic transmission check warning light Seat belt warning light Slip indicator light or Brake warnin.
Automatic transmission check warning light (A/T models) When the ignition switch is turned ON, the light comes on for 2 seconds. If the light blinks for approximately 8 seconds, it may indicate the automatic transmission system is not functioning properly.
immediately and call a NISSAN dealer or other authorized repair shop. The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See “Engine oil” in the “8. Maintenance and do-it-yourself” section.
at a low level. Add washer fluid as necessary. See “Window washer fluid” in the “8. Mainte- nance and do-it-yourself” section. Seat belt warning light and chime The light and chime remind you to fasten seat belts.
Malfunction indicator lamp (MIL) If the malfunction indicator lamp comes on steady or blinks while the engine is running, it may indicate a potential emission control mal- function. The malfunction indicator lamp may also come on steady if the fuel filler cap is loose or missing, or if the vehicle runs out of fuel.
mation, see “Traction control system (TCS)” in the “5. Starting and driving” section of this manual. Vehicle dynamic control off indicator light (if so equipped) After turning the ignition key to the ON position, the light will illuminate. The light will turn off in about 1 second if the vehicle dynamic control (VDC) system is operational.
The security condition will be shown by the security indicator light. VEHICLE SECURITY SYSTEM The vehicle security system provides visual and audio alarm signals if parts of the vehicle are disturbed. How to activate the vehicle security system 1. Close all windows.
scribed above, have it checked by your NISSAN dealer. NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) The Nissan Vehicle Immobilizer System will not allow the engine to start without the use of the registered Nissan Vehicle Immobilizer System key.
tem keys that you have when visiting your NISSAN dealer for service. The windshield wiper and washer operates when the ignition key is in the ON position. Push the lever down to operate the wiper at the following speed: q 1 Intermittent — intermittent operation can be adjusted by turning the knob toward q A (Slower) or q B (Faster).
The rear window wiper and washer operate when the ignition switch is in the ON position. Turn the switch clockwise from the OFF position to operate the wiper. q 1 Intermittent — intermittent operation (not ad- justable) q 2 Low — continuous low speed operation Push the switch forward q 3 to operate the washer.
To defog/defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the switch on. The indicator light will come on. Push the switch again to turn the defroster off. It will automatically turn off in approximately 15 minutes.
HEADLIGHT SWITCH Lighting q 1 Turn the switch to the position: The front park, side marker, tail, license plate and instrument lights will come on. q 2 Turn the switch to the position: Headlights will come on and all the other lights remain on. Headlight beam select q 1 To select the low beam, put the lever in the neutral position as shown.
TURN SIGNAL SWITCH q 1 Turn signal Move the lever up or down to signal the turning direction. When the turn is completed, the turn signals cancel automatically. q 2 Lane change signal To indicate a lane change, move the lever up or down to the point where lights begin flashing.
Push the switch (located on the center console) on to warn other drivers when you must stop or park under emergency conditions. All turn signal lights will flash. Some state or provincial laws may prohibit the use of the hazard warning flasher switch while driving.
The front seats are warmed by built-in heaters. The switches located on the center console can be operated independently of each other. 1. Start the engine. 2. Select heat range. I For low heat, press the (Low) side of the switch. I For high heat, press the (High) side of the switch.
The vehicle should be driven with the Vehicle Dynamic Control (VDC) System ON for most driving conditions. When the vehicle is stuck in mud or snow, the VDC system reduces the engine output to re- duce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor.
The digital clock (in the audio unit) displays time when the ignition key is in the ACC or ON position. If the power supply is disconnected, the clock will not indicate the correct time. Readjust the time. ADJUSTING THE TIME Adjust the time in the following steps: 1.
draw. Do not use double adapters or more than one electrical accessory. I Use this power outlet with the engine running. (If the engine is stopped, this could result in a discharged bat- tery.) I Avoid using when the air conditioner, headlights or rear window defroster is on.
INSTRUMENT POCKET (Except for Navigation system equipped models) q A Pushing the button will open the lid. q B To close, pull out the lid straight until it stops , then push down as illustrated. The lid can be damaged unless you follow this instruction when closing the lid.
CAUTION I Do not use for anything other than glasses. I Do not leave glasses in the sun- glasses holder while parking in direct sunlight. The heat may damage the glasses. TRAY The tray can be removed for cleaning by pulling upward q A . WARNING The tray should not be used while driv- ing so full attention may be given to vehicle operation.
Center console: The cup holder is in the center console box. Push the button q 1 to open the console box. The cup holder can be removed for cleaning by pulling it up q 2 . For larger cups, push down the flap q A . Passenger’s side: To use the cup holder, push it once q 1 and draw it out q 2 .
REAR FLOOR BOX The rear floor box is located behind the passen- ger’s seat. Fold the seat to use the rear floor box. When locking or unlocking the rear floor box, use the master key. The rear floor box may be opened by pulling the handle. The rear floor box light illuminates when the box lid is opened with the headlight switch ON.
POWER WINDOWS WARNING I Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before clos- ing the windows. Use the window lock switch to prevent unexpected use of the power windows. I Do not leave children unattended in- side the vehicle.
Automatic operation To fully open or close the window, completely press or lift the switch and release it; it need not be held. The window will automatically open or close all the way. To stop the window, just press or lift the switch on the opposite side.
SPOT LIGHT q A : To turn on the light, push the plastic surface of the light. Push it again to turn off the light. The spot light has a two-position switch. ( q B : DOOR, q C : OFF) When the switch is in the DOOR position, the light will illuminate when a door is opened.
The light on the vanity mirror will turn on when the cover on the vanity mirror is opened. When the vanity mirror light stays on, it will automatically turn off 30 minutes after the ignition switch has been turned to the OFF position. To turn on the light again, turn the ignition switch to the ON position.
WARNING I Do not use the HomeLink Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required by fed- eral safety standards. (These stan- dards became effective for opener models manufactured after April 1, 1982).
3. Using both hands, simultaneously press and hold both the HomeLink button you want to program and the hand-held transmitter but- ton. DO NOT release the buttons until step 4 has been completed. 4. Hold down both buttons until the indicator light on the HomeLink flashes, changing from a “slow blink” to a “rapidly flashing blink”.
light flashes rapidly (indicating successful pro- gramming). NOTE: If programming a garage door opener, etc., it is advised to unplug the device during the “cycling” process to prevent possible damage to the garage door opener compo- nents.
been programmed into HomeLink . Consult the Owner’s Manual of each device or call the manufacturer or dealer of those devices for additional information. When your vehicle is recovered, you will need to reprogram the HomeLink Univer- sal Transceiver with your new transmitter information.
MEMO Instruments and controls 2-41 Z 02.9.13/Z33-D/V5.0 X.
MEMO 2-42 Instruments and controls Z 02.9.13/Z33-D/V5.0 X.
3 Pre-driving checks and adjustments Keys ........................................................................................... 3-2 Doors......................................................................................... 3-2 Locking with key (Driver’s side) .
You can only drive your vehicle using the master or valet keys which are registered to the Nissan Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head. The master key can be used for all the locks. The valet key cannot be used for the rear floor box lock.
LOCKING WITH KEY (Driver’s side) Power The power door lock system allows you to lock or unlock all doors including the rear hatch simultaneously. I Turning the driver’s door key to the rear of the vehicle will lock all doors including the rear hatch.
LOCKING WITH POWER DOOR LOCK SWITCH All door locks will be engaged when the power door lock switch is moved to the LOCK position with the driver’s or front passenger’s door open.
HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Setting hazard indicator and horn mode This vehicle is set in hazard indicator and horn mode when you first receive the vehicle. In hazard indicator and horn mode, when the LOCK button is pushed, the hazard indicator flashes twice and the horn chirps once.
*2: Doors lock with the keyfob while the ignition switch is in the ON position. However, the hazard indicator and horn will not function. *3: Doors lock with the keyfob while any door is open. However, the hazard indicator and horn will not function. Unlocking doors 1.
LOCK button again for 3 more seconds. Releasing the rear hatch 1. Push the REAR HATCH button on the keyfob for longer than 0.5 seconds with the key removed from the ignition key cylinder. 2. The rear hatch opens. Using the panic alarm If you are near your vehicle and feel threatened, you may activate the alarm to call attention as follows: 1.
could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1).
WARNING Do not drive with the rear hatch open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Precautions when starting and driving” in the “5. Starting and driving” section for exhaust gas. OPENER OPERATION The rear hatch release switch is located be- tween the license plate lights.
SECONDARY REAR HATCH RELEASE The secondary rear hatch release mechanism allows opening the rear hatch in the event of discharged battery or emergency. The string handle is located under the strut tower bar inside the luggage compartment.
FUEL FILLER CAP The fuel filler cap is a ratcheting type. Tighten the cap clockwise until ratcheting clicks are heard. Hang the string of the cap on the hook as shown while refueling. WARNING I Gasoline is extremely flammable and highly explosive under certain condi- tions.
— Keep the pump nozzle in contact with the container while you are filling it. — Use only approved portable fuel containers for flammable liquid. I Never pour fuel into the throttle body to attempt to start your vehicle. CAUTION I If fuel is spilled on the car body, flush it away with water to avoid paint damage.
INSIDE MIRROR The night position will reduce glare from the headlights of vehicles behind you at night. WARNING Use the night position only when neces- sary, because it reduces rear view clar- ity. AUTOMATIC ANTI-GLARE INSIDE MIRROR (if so equipped) WARNING Use the AUTO position only when nec- essary, because it reduces rear view clarity.
OUTSIDE MIRRORS WARNING Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use inside mirror or glance over your shoulder to properly judge distances to other objects.
MEMO Pre-driving checks and adjustments 3-15 Z 02.9.13/Z33-D/V5.0 X.
MEMO 3-16 Pre-driving checks and adjustments Z 02.9.13/Z33-D/V5.0 X.
4 Heater, air conditioner and audio systems Ventilators ................................................................................ 4-2 Center ................................................................................. 4-2 Side ............
CENTER Adjust the air flow direction of ventilators. Moving the lever up or down will open q A or close q B the vents. To change the air flow direction, turn the dial q C . SIDE Adjust the air flow direction of ventilators by q A opening, q B closing or q C rotating as illustrated.
1. Air flow control dial 2. Temperature control dial* 3. Fan control dial 4. Rear window defroster button (Refer to the “2. Instruments and controls” section.) 5. Air intake button (Air recirculation and Fresh air) 6. A/C (Air conditioner) button * The display of degrees: “60-75-90” is used for °F (US).
AUTOMATIC OPERATION Cooling and/or dehumidified heating (AUTO) This mode may be normally used all year round as the system automatically works to keep a constant temperature. Air flow distribution and fan speed are also controlled automatically. 1. Turn the fan control dial and air flow control dial to the AUTO position.
( and ) will flash twice, and then the intake air will be controlled automatically. During this AUTO mode, the indicator light of the currently selected mode illuminates. I When the air flow control dial is in the or position, the air recirculation mode does not activate.
The air conditioning system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. This refrigerant will not harm the earth’s ozone layer. How- ever, special charging equipment and lubricant are required when servicing your NISSAN air conditioner.
FM RADIO RECEPTION Range: FM range is normally limited to 25 to 30 miles (40 to 48 km), with monaural (single channel) FM having slightly more range than stereo FM. External influences may sometimes interfere with FM station reception even if the FM station is within 25 miles (40 km).
played. This residue accumulation can cause weak or wavering sound, and should be removed periodically with a head cleaning tape. If the residue is not removed periodically, the player may need to be disassembled for cleaning. Compact Disc (CD) player I During cold weather or rainy days, the player may malfunction due to the hu- midity.
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER 1. CD EJECT button 2. SEEK/APS REW, APS FF/TRACK CHANGE button 3. DISP (Display) CHANGE (Clock, CD play time) button 4. SCAN tuning button 5. CD play button 6. FM band select button 7. AM band select button 8.
Audio main operation ON ⋅ OFF/Volume control: Turn the ignition key to ACC or ON, and then push the ON ⋅ OFF/VOL (Volume) control knob while the system is off to call up the mode (radio or CD) which was playing immediately before the system was turned off.
SCAN tuning: Push the SCAN tuning button to tune from low to high frequencies and stops at each broad- casting station for 5 seconds. Pushing the but- ton again during this 5 second period will stop SCAN tuning and the radio will remain tuned to that station.
skipped through, the first program will be played.) When the (APS REW) button is pushed, the program being played returns to its beginning. Push several times to skip back through programs. The compact disc will go back the number of times the button is pushed.
FM-AM RADIO WITH CASSETTE PLAYER AND COMPACT DISC (CD) CHANGER 1. CD LOAD button 2. SEEK/APS REW, APS FF/TRACK CHANGE button 3. DISP (Display) CHANGE (Clock, CD play time) button 4. SCAN tuning button 5. CD PLAY button 6. TAPE PLAY button 7. FM/AM band select button 8.
Audio main operation Head unit: The tape deck employs a permalloy head which allows for improved reproduction of high fre- quency ranges. Noise is also greatly reduced by the combined use of the Dolby NR (Noise Reduction) system.
change from stereo to monaural reception. TUNE (Tuning): WARNING The radio should not be tuned while driving so full attention may be given to vehicle operation. Use the TUNE button or for manual tuning. To move quickly through the channels, hold either side of the TUNE button down for more than 0.
2. PTY SEEK tuning mode After selecting a PTY name, push the SEEK button or within 10 seconds. Tuning to the PTY station will start. If you do not push the SEEK button within the 10 second period, the PTY mode will be can- celed.
once, the program being played starts over from the beginning. Push the (APS REW) but- ton several times to skip back several selections. The tape will go back the number of times the button is pushed. Either the FF or REW symbol flashes on the display window while searching for the selection.
released, the compact disc will return to normal play speed. APS (Automatic Program Search) FF, APS REW: When the (APS FF) button is pushed while the compact disc is being played, the program next to the present one will start to play from its beginning.
CD CARE AND CLEANING I Handle a CD by its edges. Never touch the surface of the disc. Do not bend the disc. I Always place the discs in the storage case when they are not being used. I To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth.
CAUTION I Keep the antenna as far as possible away from the Engine Control Mod- ule (ECM). I Keep the antenna wire more than 8 in (20 cm) away from the Multiport Fuel Injection harness. Do not route the antenna wire next to any harness. I Adjust the antenna standing-wave ratio as recommended by the manu- facturer.
5 Starting and driving Precautions when starting and driving ............................. 5-2 Exhaust gas (Carbon monoxide) .................................. 5-2 Three way catalyst ........................................................... 5-3 Low tire pressure warning system (if so equipped) .
WARNING I Do not leave children, impaired adults, or pets alone in your vehicle. They could accidentally injure them- selves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
d. You have had an accident involv- ing damage to the exhaust system, underbody, or rear of the vehicle. THREE WAY CATALYST The three way catalyst is an emission control device installed in the exhaust system. Exhaust gases in the converter are burned at high tem- peratures to help reduce pollutants.
“Warning/indicator lights and audible remind- ers” in the “2. Instruments and controls” section. WARNING I If the low tire pressure warning light in the meter panel comes on and/or the PSI ind.
times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the-counter drugs which may cause drowsiness). Always wear your seat belt. See “Seat Belts” in the “1. Seats, restraints and supplemental air bag sys- tems” section.
1. Move the selector lever into the P (Park) position. 2. Turn the ignition key slightly in the ON direc- tion. 3. Turn the key toward the LOCK position. 4. Remove the key. If the key is removed from the ignition switch, the selector lever cannot be moved from P (Park) position.
the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steer- ing wheel slightly right and left. WARNING Never remove or turn the key to the LOCK position while driving. The steer- ing wheel will lock.
I Make sure the area around the vehicle is clear. I Maintenance items should be checked peri- odically, for example, each time you check engine oil. I Check that all windows and lights are clean. I Visually inspect tires for their appearance and condition.
AUTOMATIC TRANSMISSION 5 speed automatic transmission The automatic transmission in your vehicle is electronically controlled by a transmission con- trol module to produce maximum power and smooth operation. Shown on the following pages are the recom- mended operating procedures for this transmis- sion.
To move the selector lever, : Push the button while depressing the brake pedal, : Push the button, : Just move the selector lever. Shifting After starting the engine, fully depress the brake pedal and shift the selector lever from P (Park) to R (Reverse), N (Neutral), D (Drive), or Manual shift mode position.
shift mode. Shift range can be selected manu- ally. In the manual shift mode, the shift range is displayed on the position indicator in the meter. Shift ranges up or down one by one as follows: M 1 → ← M 2 → ← M 3 → ← M 4 → ← M 5 M 5 (5th): Use this position for all normal forward driving.
Shift lock release If the battery charge is low or discharged, the select lever may not be moved from the P (Park) position even with the brake pedal depressed. To move the select lever, depress the brake pedal, apply the parking brake, and push the shift lock release button by using a suitable tool as shown.
light, shift to N (Neutral) and release the clutch pedal with the foot brake applied. Up-shift indicator The manual transmission up-shift indicator is situated in the tachometer and shows the driver the time to shift into a higher gear by illuminating.
Suggested up-shift speeds Shown below are suggested vehicle speeds for shifting into a higher gear. These suggestions relate to fuel economy and vehicle performance. Actual up-shift speeds will vary according to road conditions, the weather and individual driv- ing habits.
4. Before driving, be sure the brake warning light goes out. WARNING I Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident. I Do not release the parking brake from outside the vehicle.
1. RESUME or ACCEL switch 2. COAST or SET switch 3. ON ⋅ OFF switch 4. CANCEL switch CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed between 25 to 89 MPH (40 to 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the main switch on.
SET switch. Each time you do this, the set speed will decrease by about 1 MPH (1.6 km/h). To resume the preset speed, push and re- lease the RES/ACCEL set switch. The vehicle will resume the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).
I Follow the recommended periodic mainte- nance schedule. I Keep the tires inflated at the correct pres- sure. Low pressure will increase tire wear and waste fuel. I Keep the front wheels in correct alignment. Improper alignment will cause not only tire wear but also lower fuel economy.
WARNING I Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) for automatic transmission models or in an appropriate gear for manual transmission models. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in an accident.
BRAKING PRECAUTIONS The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at two wheels. Vacuum assisted brake The brake booster aids braking by using engine vacuum. If the engine stops, you can stop the vehicle by depressing the brake pedal.
While the actuator is working, you may feel a pulsation in the brake pedal and hear a noise or vibration from the actuator under the hood. This is normal and indicates that the anti-lock system is working properly. However, the pulsation may indicate that road conditions are hazardous and extra care is required while driving.
On slippery surfaces such as wet asphalt roads, vehicle wheels may spin when the vehicle is accelerated. This wheel spin reduces accelera- tion, or causes the vehicle to swerve, thus decreasing vehicle stability.
surface. The brake LSD system brakes the spin- ning wheel to distribute the driving power to the other driving wheel. If the vehicle is operated with the vehicle dy- namic control system turned off, all VDC and TCS functions will be turned off. The brake LSD system and ABS will still operate with the VDC system off.
FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing, apply de-icer or glycerin to it through the key hole. If the lock becomes frozen, heat the key before inserting it into the key hole.
ice and snow from the windows and wiper blades. I a sturdy, flat board to be placed under the jack to give it firm support. I a shovel to dig the vehicle out of snow-drifts.
MEMO 5-26 Starting and driving Z 02.9.13/Z33-D/V5.0 X.
6 In case of emergency Flat tire ...................................................................................... 6-2 Low tire pressure warning system (if so equipped) ................................................................ 6-2 Changing a flat tire .
LOW TIRE PRESSURE WARNING SYSTEM (if so equipped) The low tire pressure warning system which displays pressure of all tires (except the spare tire) on the trip computer by sending a signal from a sensor that is installed in each wheel.
verse), or the automatic transmission into P (Park). I Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous. I Never change tires if oncoming traffic is close to your vehicle. Wait for pro- fessional road assistance.
Jacking up vehicle and removing the damaged tire Carefully read the caution label attached to the jack body and the following instruc- tions. 1. Place the jack directly under the jack-up point as illustrated above so that top of the jack contacts the vehicle at the jack up point.
I Use the correct jack up points; never use any other part of the vehicle for jack support. I Never jack up the vehicle more than necessary. I Never use blocks on or under the jack. I Do not start or run engine while ve- hicle is on the jack, as it may cause the vehicle to move.
For models equipped with the low tire pressure warning system: After adjusting tire pressure to the COLD tire pressure, the display of the tire pressure infor- mation may show higher pressure than the COLD tire pressure after the vehicle has been driven more than 1 mile (1.
12 volts. Use of an improperly rated battery can damage your vehicle. I Whenever working on or near a bat- tery, always wear suitable eye protec- tors (for example, goggles or indus- trial safety spectacles) and remove rings, metal bands, or any other jew- elry.
CAUTION I Always connect positive (+) to posi- tive (+) and negative (−) to body ground (for example, strut mounting bolt, etc. — not to the battery). I Make sure that cables do not touch moving parts in the engine compart- ment and that clamps do not contact any other metal.
WARNING I Do not continue to drive if your ve- hicle overheats. Doing so could cause a vehicle fire. I To avoid the danger of being scalded, never remove the radiator cap while the engine is still hot. When the ra- diator cap is removed, pressurized hot water will spurt out, possibly causing serious injury.
When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could damage your vehicle. Towing instructions are available from a NISSAN dealer. Local service operators are generally familiar with the appli- cable laws and procedures for towing.
CAUTION I Never tow automatic transmission models with the rear wheels on the ground or four wheels on the ground (forward or backward) as this may cause serious and expensive damage to the transmission. If it is necessary to tow the vehicle with the front wheels raised, always use towing dollies under the rear wheels.
I Pulling devices should be routed so they do not touch any part of the suspension, steer- ing, brake or cooling systems. I Always pull the cable straight out from the front of the vehicle. Never pull on the vehicle at an angle. I Pulling devices such as ropes or canvas straps are not recommended for use in ve- hicle towing or recovery.
7 Appearance and care Cleaning exterior .................................................................... 7-2 Washing ............................................................................. 7-2 Waxing .........................................
In order to maintain the appearance of your vehicle, it is important to take proper care of it. In the following cases, please wash your vehicle as soon as possible to protect the paint surface.
specified for use over clear coats, such as Nissan Liquid or Spray Wax. Your NISSAN dealer can assist you in choosing the proper product. I Wax your vehicle only after a thorough wash- ing. Follow the instructions supplied with the wax. I Do not use a wax containing any abrasives, cutting compounds or cleaners that may damage the vehicle finish.
Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry soft cloth. Before using any fabric protector, read the manufacturer’s recommendations.
SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely before using them. WARNING Do not allow wet belts to roll up in the retractor. NEVER use bleach, dye, or chemical solvents since these may se- verely weaken the seat belt webbing.
CAUTION I NEVER remove dirt, sand or other debris from the passenger compart- ment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. I Never allow water or other liquids to come in contact with electronic com- ponents inside the vehicle as this may damage them.
8 Maintenance and do-it-yourself Maintenance requirements .................................................. 8-2 General maintenance ............................................................ 8-2 Explanation of general maintenance items ............
Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN’s good mechanical condition, as well as its emission and engine performance.
Tire rotation*: Tires cannot be rotated in this vehicle. Wheel alignment and balance: If the vehicle pulls to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel align- ment.
Automatic transmission P (Park) position mechanism: On a fairly steep hill check that the vehicle is held securely with the selector lever in the P (Park) position without applying any brakes. Under the hood and the vehicle The maintenance items listed here should be checked periodically (for example, each time you check the engine oil or refuel).
When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle.
able. See “Owner’s Manual/Service Manual or- der information” in the “9. Technical and con- sumer information” section. You should be aware that incomplete or im- proper servicing may result in operating difficul- ties or excessive emissions, and could affect your warranty coverage.
1. Fuse/fusible link holder 2. Battery 3. Engine oil filler cap 4. Brake fluid reservoir 5. Clutch fluid reservoir (M/T models) 6. Windshield washer fluid reservoir 7. Power steering fluid reservoir 8. Engine coolant reservoir 9. Radiator filler cap 10.
The engine cooling system is filled at the factory with a high-quality, year-round, anti-freeze cool- ant solution. The anti-freeze solution contains rust and corrosion inhibitors, therefore additional cooling system additives are not necessary.
CHANGING ENGINE COOLANT I Major cooling system repairs should be per- formed by your NISSAN dealer. The service procedures can be found in the appropriate NISSAN Service Manual. I Improper servicing can result in reduced heater performance and engine overheating.
CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply parking brake. 2. Run the engine until it reaches operating temperature. 3. Turn off the engine. Wait more than 10 minutes for the oil to drain back into the oil pan. 4. Remove the dipstick and wipe it clean.
I A suitable adapter should be attached to the jack stand saddle. 5. Remove the plastic engine undercover. a. Remove the small plastic clip at the center point of the undercover. b. Then remove the other bolts that hold the undercover in place. CAUTION Make sure the correct lifting and sup- port points are used to avoid vehicle damage.
CAUTION The dipstick must be inserted in place to prevent oil spillage from the dipstick hole while filling the engine with oil. See “Capacities and recommended fuel/ lubricants” in the “9. Technical and consumer information” section for drain and refill capac- ity.
Check the fluid level in the reservoir tank. The fluid level should be checked using the HOT range at fluid temperatures of 122 - 176°F (50 - 80°C) or using the COLD range at fluid tem- peratures of 32 - 86°F (0 - 30°C). CAUTION I Do not overfill.
CLUTCH FLUID Check the fluid level in the reservoir. If the fluid level is below the MIN. line, add Genuine Nissan Brake Fluid or equivalent DOT 3 fluid up to the MAX. line. If fluid is added frequently, the system should be thoroughly checked by your NISSAN dealer.
WARNING Anti-freeze is poisonous and should be stored carefully in marked containers out of the reach of children. CAUTION Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint. I Keep the battery surface clean and dry.
or rub your eyes. Thoroughly wash your hands. If you get acid on your eyes, skin or clothing, immediately flush with water for at least 15 min- utes and seek medical attention.
1. Power steering fluid pump 2. Alternator 3. Crankshaft pulley 4. Air conditioner compressor H : Tension checking points WARNING Be sure the ignition key is in the OFF or LOCK position. The engine could rotate unexpectedly. 1. Visually inspect each belt for signs of unusual wear, cuts, fraying, oil adhesion or looseness.
Platinum-tipped spark plugs It is not necessary to replace the platinum-tipped spark plugs as frequently as the conventional type spark plugs since they will last much longer. Follow the maintenance schedule but, do not reuse them by cleaning or regapping.
CAUTION I After wiper blade replacement, return the wiper arm to its original position. Otherwise it may be damaged when the engine hood is opened. I Make sure the wiper blade contacts the glass, otherwise the arm may be damaged from wind pressure. I Worn windshield wiper blades can damage the windshield and impair driver vision.
REPLACING Replace the wiper blades if they are worn. 1. Pull the wiper arm. 2. Push the lock pin, then remove the wiper blade. 3. Insert the new wiper blade to the wiper arm until a click sounds. If necessary, clean the windshield washer nozzle with a needle or small pin.
CHECKING PARKING BRAKE From the released position, pull the parking brake lever up slowly and firmly. If the number of clicks is out of the range listed above, see your NISSAN dealer. CHECKING BRAKE PEDAL With the engine running, check the distance between the upper surface of the pedal and the metal floor.
BRAKE BOOSTER Check the brake booster function as follows: 1. With the engine off, press and release the brake pedal several times. When brake pedal movement (distance of travel) remains the same from one pedal application to the next, continue on to the next step.
system checked and repaired by your NISSAN dealer. Fusible links If any electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace only with genuine NISSAN parts. PASSENGER COMPARTMENT If any electrical equipment does not operate, check for an open fuse.
Replace the battery as follows: 1. Open the lid using a suitable tool. 2. Replace the battery with a new one. Recommended battery: CR2025 or equiva- lent Make sure that the ⊕ side faces the bottom case. 3. Close the lid securely. 4. Push the keyfob button two or three times to check its operation.
1. Headlight (low-beam, high-beam) 2. Spot light 3. Front park light 4. Front turn signal light 5. Front side marker light 6. Luggage compartment light 7. High-mounted stop light 8. Rear combination light (Side marker, Stop/Tail) 9. License plate lights 10.
HEADLIGHTS Replacing If replacement is required, see a NISSAN dealer. Xenon headlight bulb: WARNING HIGH VOLTAGE When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble the headlight assembly.
EXTERIOR AND INTERIOR LIGHTS Item Wattage (W) Bulb No. Front turn signal* 21 T20 Front park light* 5 T10 Front side marker light* 5 T10 Rear combination light (Upper) Stop/Tail 21/5 T20 Side marker li.
Rear combination light (Stop/Tail, Side marker) q 1 Remove the covers and the bolts from the 3 places. q 2 Use a flat-bladed screwdriver to make a clearance between the light unit and the vehicle. q 3 Pull the light unit toward the direction shown in the illustration.
If you have a flat tire, see “Flat tire” in the “6. In case of emergency” section. TIRE PRESSURE Maximum inflation pressure Do not exceed the maximum inflation pressures shown on the side wall of the tire. Tire inflation pressure Check the tire pressure (including spare) at least once a month and always prior to long distance trips.
parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. COLD tire pressures are shown on the tire placard affixed to the inside of the console box lid.
All season tires NISSAN specifies all season tires on some models to provide good performance for use all year around, including snowy and icy road con- ditions. All season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than all season tires and may be more appropriate in some areas.
Tire wear and damage WARNING I Tires should be periodically in- spected for wear, cracking, bulging, or objects caught in the tread. If ex- cessive wear, cracks, bulging, or deep cuts are found, the tire should be replaced. I The original tires have a built-in tread wear indicator.
replacement and/or system reset- ting. (For models with the low tire pressure warning system) I Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warn- ing. I The use of retread tire is not recom- mended.
spare tire. Tire chains will not fit properly on the T-type spare tire and may cause damage to the vehicle. I Tire tread of the T-type spare tire will wear at a faster rate than the original tire. Replace the T-type spare tire as soon as the tread wear indicators appear.
9 Technical and consumer information Capacities and recommended fuel/lubricants ................ 9-2 Fuel recommendation ...................................................... 9-3 Engine oil and oil filter recommendation .................... 9-5 Recommended SAE viscosity number .
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure instructed in the “8.
FUEL RECOMMENDATION Use unleaded premium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research octane number 96). If premium gasoline is not available, unleaded regular.
Aftermarket fuel additives NISSAN does not recommend the use of any fuel additives (that is, fuel injector cleaner, oc- tane booster, intake valve deposit removers, etc.
ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It is essential to choose the correct quality, and viscosity oil to ensure satisfactory engine life and performance. NISSAN recommends the use of a low friction oil (energy conserving oil) in order to improve fuel economy and conserve energy.
Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Oil and filter other than the specified quality, or oil and filter change intervals longer than recommended could reduce engine life.
Contact your NISSAN dealer when servicing your air conditioning system. Technical and consumer information 9-7 Z 02.9.13/Z33-D/V5.0 X.
ENGINE Model VQ35DE Type Gasoline, 4-cycle Cylinder arrangement 6-cylinder, V-slanted at 60° Bore x Stroke in (mm) 3.760 x 3.205 (95.5 x 81.4) Displacement cu in (cm 3 ) 213.45 (3,498) Firing order 1-2-3-4-5-6*1 Idle speed rpm See the emission control label on the underside of the hood.
WHEELS AND TIRES Road wheel Type Size Offset in (mm) Aluminum Front 17 x 7-1/2JJ 1.18 (30) 18 x 8JJ* Rear 17 x 8JJ 1.30 (33) 18 x 8JJ* 1.18 (30) 18 x 8-1/2JJ* 1.
When planning to travel in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with too low an octane rating may cause engine damage. All gasoline vehicles must be operated with unleaded engine gaso- line.
ENGINE SERIAL NUMBER The number is stamped on the engine as shown. F.M.V.S.S. CERTIFICATION LABEL The Federal Motor Vehicle Safety Standards (F.M.V.S.S.
TIRE PLACARD The cold tire pressure is shown on the tire placard affixed to the inside of the console box lid. AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed inside of the hood as shown. STI0324 STI0325 9-12 Technical and consumer information Z 02.
Use the following steps to mount the license plate: Before mounting the license plate, confirm that the following parts are enclosed in the vinyl bag. I License plate bracket I J-nut x 2 I Screw x 2 I Screw grommet x 2 1.
8. Install the license plate with bolts that are no longer than 0.55 in (14 mm). WARNING I It is extremely dangerous to ride in a cargo area inside of a vehicle.
ceeded. If GVWR is exceeded, remove cargo as necessary. If either the front or rear GAWR is exceeded, shift the load or remove cargo as necessary. LOADING TIPS I The GVW must not exceed GVWR or GAWR as specified on the F.M.V.S.S. certi- fication label.
MAXIMUM LOAD LIMITS Maximum trailer loads Never allow the total trailer load to exceed 1,000 lb (454 kg). The total trailer load equals trailer weight plus its cargo weight. Towing loads greater than 1,000 lb (454 kg) or using improper towing equipment could adversely affect vehicle handling, braking and performance.
TOWING LOAD/SPECIFICATION CHART Unit: lb (kg) MAXIMUM TOWING LOAD 1,000 (454) MAXIMUM TONGUE LOAD 110 (49) TOWING SAFETY Trailer hitch Choose a proper hitch for your vehicle and trailer.
load, worn suspension or other possible causes of either condition. I Always secure items in the trailer to prevent load shifts while driving. I Be certain your rear view mirrors conform to all federal, state or local regulations. If not, install any mirrors required for towing before driving the vehicle.
sion oil more frequently. See the Service and Maintenance Guide. DOT (Department Of Transportation) Quality Grades: All passenger car tires must conform to federal safety requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
WARNING The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combi- nation, can cause heat buildup and pos- sible tire failure.
Due to legal requirements in some states/ areas, your vehicle may be required to be in what is called the “ready condition” for an Inspection/Maintenance (I/M) test of the emis- sion control system. The vehicle is set to the “ready condition” when it is driven through certain driving patterns.
A genuine NISSAN Service Manual is the best source of service and repair information for your vehicle. Filled with wiring diagrams, illustrations and step-by-step diagnostic and adjustment procedures, this manual is the same one used by the factory trained technicians working at autho- rized NISSAN dealerships.
Insist on the use of Genuine Nissan Collision Parts! If you want your vehicle to be restored using parts made to Nissan’s original exacting speci- fications — if you want to help it to last and hold its resale value, the solution is simple. Tell your insurance agent and your repair shop to only use Genuine Nissan Collision Parts.
MEMO 9-24 Technical and consumer information Z 02.9.13/Z33-D/V5.0 X.
10 Index A ABS (Anti-lock brake system)................................ 5-20 Air bag ON/OFF switch .......................................... 1-21 Air bag system Front (See supplemental front air bag system) ...........................................
Controls, Heater and air conditioner controls (automatic) ..................................................................... 4-3 Coolant Capacities and recommended fuel/ lubricants ................................................................. 9-2 Changing engine coolant .
Tachometer ............................................................. 2-5 Trip computer ......................................................... 2-8 General maintenance .................................................. 8-2 H Hatch, Rear hatch....
N New vehicle break-in ................................................ 5-17 Nissan vehicle Immobilizer System ....................... 2-16 Nissan Vehicle Immobilizer System, Engine start................................................................
Security systems (Nissan Vehicle Immobilizer System), Engine start ............................................... 2-18 Security systems (See vehicle security system) ......................................................................... 2-16 Servicing air conditioner .
V Vanity mirror light ...................................................... 2-36 Vehicle Dimensions and weights ..................................... 9-9 Dynamic control (VDC) system....................... 5-22 Identification number (VIN)............
FUEL RECOMMENDATION: Use unleaded premium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research octane number 96). If premium gasoline is not available, unleaded regula.
QUICK REFERENCE 1. Engine oil (P.8-10) 2. Brake fluid (P.8-13) 3. Meters and gauges (P.2-3) 4. Fuel filler lid release (P.3-10) 5. Hood release (P.3-8) 6. Seat belt (P.1-18) 7. Door lock/key (P.3-2) 8. Rear hatch release (P.3-9) 9. Engine coolant (P.8-8) 10.
Een belangrijk punt na aankoop van elk apparaat Nissan 350Z (2003) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Nissan 350Z (2003) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Nissan 350Z (2003) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Nissan 350Z (2003) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Nissan 350Z (2003) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Nissan 350Z (2003) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Nissan 350Z (2003) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Nissan 350Z (2003) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
