Gebruiksaanwijzing /service van het product Maxima (2009) van de fabrikant Nissan
Ga naar pagina of 418
W elcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. This manual was prepared to help you under- stand the operation and maintenance of your vehicle so that you may enjoy many miles (kilome- ters) of driving pleasure.
This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle. All information, specifications and illustrations in this manual are those in effect at the time of printing.
BLUETOOTH 威 is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Visteon. Gracenote 威 is a registered trademark of Gracenote, Inc. The Gracenote logo and logo type, and the “Powered by Gracenote” logo are trademarks of Gracenote.
NISSAN CARE S... Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Y our satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Y our NISSAN dealer is always available to assist you with all your automobile sales and service needs.
T able of Contents Illustrated table of contents Safety—Seats, seat belts and supplemental restraint system Instruments and controls Pre-driving checks and adjustments Monitor, climate, audio, phone.
0 Illustrated table of contents Air bags, seat belts and child restraints ..............0 - 2 Exterior front ......................................0 - 3 Exterior rear .......................................0 - 4 Passenger compartment .................
1. T op tether strap anchor (P . 1-20) 2. Rear head restraint (P . 1-7) 3. Rear seat belts (P . 1-9) 4. Roof-mounted curtain side-impact supplemental air bag (P . 1-35) 5. Front seat-mounted side-impact supplemental air bags (P . 1-35) 6. Front-seat Active Head Restraints (P .
1. Engine hood (P . 3-18) 2. Windshield wiper and washer switch (P . 2-25) 3. Windshield (P . 8-18) 4. Moonroof (if so equipped) (P . 2-44) 5. P ower windows (P . 2-41) 6. Door locks, Nissan Intelligent K ey™, keys, request button (P . 3-4, 3-2, 3-2, 3-2) 7.
1. Rear window defroster switch (P . 2-26) 2. Interior trunk lid release (P . 3-20) 3. T runk lid (P . 3-18) 4. V ehicle loading (P . 9-12) 5. Exterior trunk lid release/request button (P . 3-13) 6. Replacing bulbs (P . 8-28) 7. Fuel-filler cap, fuel recommendation (P .
1. Interior trunk access (P . 1-5) 2. Moonroof (P . 2-44) 3. Sun visors (P . 3-24) 4. Interior lights, illuminated entry (P . 2-48) 5. HomeLink 姞 (if so equipped) (P . 2-51) 6. Interior mirrors (P . 3-25) 7. Glove box (P . 2-39) 8. Front cup holders (P .
1. Side and center vents (P . 4-34) 2. Headlight/fog light/turn signal switch (P . 2-27) 3. Steering wheel switch for audio control and Bluetooth 姞 Hands-Free Phone System (if so equipped) (P . 4-84, 4-88) 4. Meters and gauges (P . 2-3) 5. Driver supplemental air bag/horn (P .
24. Rear control cancel switch (if so equipped) (P . 2-47) 25. V ehicle Dynamic Control (VDC) OFF switch (P . 2-35) 26. Outside mirror controls (P . 3-27) 27. Heated steering wheel switch (if so equipped) (P . 2-34) 28. T runk lid release switch (P . 3-20) * Refer to the separate Navigation System Owner’s Manual (if so equipped) .
1. P ower steering fluid reservoir (P . 8-11) 2. Engine oil filler cap (P . 8-8) 3. Brake fluid reservoir (P . 8-12) 4. Air cleaner (P . 8-17) 5. Fuse block (P . 8-20) 6. Battery (P . 8-13) 7. Fuse/fusible link box (P . 8-20) 8. Engine oil dipstick (P .
W arning light Name Page or Anti-lock Braking System (ABS) warn- ing light 2-10 or Brake warning light 2-11 Charge warning light 2-11 Engine oil pressure warning light 2-11 Low tire pressure warning l.
0-10 Illustrated table of contents MEMO.
1 Safety—Seats, seat belts and supplemental restraint system Seats ............................................1 - 2 Front power seat adjustment .....................1 - 3 Folding rear seat (if so equipped) .................1 - 5 Head restraint adjustment .
WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. Y ou could also slide under the lap belt and receive serious internal injuries.
FRONT POWER SEAT ADJUSTMENT Operating tips ● The power seat motor has an auto-reset overload protection circuit. If the motor stops during operation, wait 30 seconds, then reactivate the switch. ● Do not operate the power seat switch for a long period of time when the engine is off.
Seat lifter (driver’s seat) Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion. Lumbar support (driver’s seat) The lumbar support feature provides lower back support to the driver. Move the lever up or down (manual) or move the switch forward or backward (power) to adjust the seat lumbar area.
Thigh extension (driver’s side only , if so equipped) Pull up and hold the lever to extend the front portion to the desired position. FOLDING REAR SEAT (if so equipped) Interior trunk access For models without a rear center console, the trunk can be accessed from the passenger side of the rear seat for loading and unloading, as shown.
● When returning the seatbacks to the upright position, be certain they are completely secured in the latched posi- tion. If they are not completely secured, passengers may be injured in an acci- dent or sudden stop.
Center armrest Pull the armrest down until it is horizontal. HEAD RESTRAINT ADJUSTMENT T o raise the head restraint, pull it up. T o lower, push and hold the lock knob and push the head restraint down. WARNING Head restraints should be adjusted prop- erly as they may provide significant pro- tection against injury in an accident.
Adjust the head restraint so the center is level with the center of your ears. FRONT-SEAT ACTIVE HEAD RESTRAINTS WARNING ● Always adjust the head restraints prop- erly as specified in this section. Failure to do so can reduce the effectiveness of the Active Head Restraint.
PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly ad- justed and you are sitting upright and well back in your seat with both feet on the floor, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced.
WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly re- strained in the rear seat and, if appro- priate, in a child restraint. WARNING ● The seat belt should be properly ad- justed to a snug fit.
WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never put the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder. ● Position the lap belt as low and snug as possible AROUND THE HIPS, NOT THE WAIST .
CHILD SAFETY Children need adults to help protect them. They need to be properly restrained. In addition to the general information in this manual, child safety information is available from many other sources, including doctors, teachers, government traffic safety offices, and community organizations.
80 lbs (36 kg) . A booster seat should be used to obtain proper seat belt fit. NISSAN recommends that a child be placed in a commercially available booster seat if the shoul- der belt in the child’s seating position fits close to the face or neck or if the lap portion of the seat belt goes across the abdomen.
Fastening the seat belts 䊊 1 Adjust the seat. See “Seats” earlier in this section. 䊊 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage. ● The retractor is designed to lock during a sudden stop or on impact.
The Emergency Locking Retractor (ELR) mode allows the seat belt to extend and retract to allow the driver and passengers some freedom of movement in the seat.
Shoulder belt height adjustment (front seats) The shoulder belt anchor height should be ad- justed to the position best for you. (See “Precau- tions on seat belt usage” earlier in this section.
PRECAUTIONS ON CHILD RESTRAINTS WARNING ● Infants and small children should al- ways be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint can re- sult in serious injury or death. ● Infants and small children should never be carried on your lap.
● If the child restraint is not anchored properly, the risk of a child being in- jured in a collision or a sudden stop greatly increases. ● Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints.
LA T CH (Lower Anchors and T ethers for CHildren) SYSTEM Y our vehicle is equipped with special anchor points that are used with LA T CH (Lower Anchors and T ethers for CHildren) system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system.
Installing child restraint LA T CH anchor attachments LA T CH compatible child restraints include two rigid or webbing-mounted attachments that can be connected to two anchors located at certain seating positions in your vehicle. With this sys- tem, you do not have to use a vehicle seat belt to secure the child restraint.
T op T ether Anchor P oint Locations Anchor points 䊊 1 are located on the rear parcel shelf. Installing top tether strap First, secure the child restraint with the LA T CH system (rear outboard seating positions only) or the seat belt, as applicable.
2. Secure the child restraint anchor attach- ments to the LA TCH lower anchors. Check to make sure the LA TCH attachment is prop- erly attached to the lower anchors. 3. The back of the child restraint should be secured against the vehicle seatback. If necessary, adjust or remove the head restraint to obtain the correct child restraint fit.
6. After attaching the child restraint, test it be- fore you place the child in it. Push it from side to side while holding the seat near the LA T CH attachment path. The child restraint should not move more than 1 inch (25 mm) , from side to side. T ry to tug it forward and check to see if the LA T CH attachment holds the restraint in place.
3. For child restraints that are equipped with webbing-mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.
5. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 2 through 4. CHILD RESTRAINT INSTALLATION USING THE SEAT BELTS WARNING ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front passenger seat.
Front-facing Follow these steps to install a front-facing child restraint using the vehicle seat belt in the rear seats or in the front passenger seat: 1. If you must install a child restraint in the front seat, it should be placed in a front-facing direction only.
4. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode) . It reverts to Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted.
7. If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anchor point (rear seat installation only) .
Rear-facing Follow these steps to install a rear-facing child restraint using the vehicle seat belt in the rear seats: 1. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat. Always follow the restraint manufac- turer’s instructions.
4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. 䊊 5 Remove any additional slack from the child restraint; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seat- back while pulling up on the seat belt.
7. Check that the retractor is in the ALR mode by trying to pull more seat belt out of the retractor. If you cannot pull any more seat belt webbing out of the retractor, the retrac- tor is in the ALR mode. 8. Check to make sure that the child restraint is properly secured prior to each use.
● Do not use towels, books, pillows or other items in place of a booster seat. Items such as these may move during normal driving or a collision and result in serious injury or death.
● Make sure the child’s head will be properly supported by the booster seat or vehicle seat. The seatback must be at or above the center of the child’s ears. For example, if a low back booster seat 䊊 1 is chosen, the vehicle seatback must be at or above the center of the child’s ears.
Follow these steps to install a booster seat in the rear seat or in the front passenger seat: 1. If you must install a booster seat in the front seat, move the seat to the rear- most position. 2. Position the booster seat on the seat. Only place it in a front facing direction.
4. Position the lap portion of the seat belt low and snug on the child’s hips. Be sure to follow the booster seat manufacturer’s in- structions for adjusting the seat belt routing. 5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack.
Roof-mounted curtain side-impact supple- mental air bag system: This system can help cushion the impact force to the head of occu- pants in front and rear outboard seating positions in certain side-impact collisions. The curtain air bags are designed to inflate on the side where the vehicle is impacted.
● The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened. The Advanced Air Bag System monitors the severity of a collision and seat belt us- age then inflates the air bags. Failure to properly wear seat belts can increase the risk or severity of injury in an accident.
WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.
WARNING ● Children may be severely injured or killed when the front air bags, side air bags or curtain air bags inflate if they are not properly restrained.
WARNING Front seat-mounted side-impact supple- mental air bags and roof-mounted curtain side-impact supplemental air bags: ● The side air bags and curtain air bags ordinarily will not inflate in the event of a frontal impact, rear impact, rollover or lower severity side collision.
WARNING ● When sitting in the rear seat, do not hold onto the seatback of the front seat. If the side air bag inflates, you may be seriously injured. Be especially careful with children, who should always be properly restrained. Some examples of dangerous riding positions are shown in the illustrations.
1. Roof-mounted curtain side-impact supplemental air bag inflators 2. Roof-mounted curtain side-impact supplemental air bags 3. Front seat-mounted side-impact supplemental air bag modules 4. Air bag Control Unit (ACU) 5. Supplemental front-impact air bag mod- ules 6.
The NISSAN Advanced Air Bag System has dual stage inflators. It also monitors information from the crash zone sensor, the Air Bag Control Unit (ACU) , seat belt buckle sensors, occupant clas- sification sensor (pattern sensor) and passenger seat belt tension sensor.
Front passenger air bag and status light WARNING The front passenger air bag is designed to automatically turn OFF under some con- ditions. Read this section carefully to learn how it operates. Proper use of the seat, seat belt and child restraints is nec- essary for most effective protection.
ger air bag to be automatically turned OFF . For small adults it may be turned OFF , however if the occupant takes his/her weight off the seat cush- ion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position) , this could cause the sensor to turn the air bag OFF .
Other supplemental front-impact air bag precautions WARNING ● Do not place any objects on the steer- ing wheel pad or on the instrument panel. Also, do not place any objects between any occupant and the steering wheel or instrument panel. Such ob- jects may become dangerous projec- tiles and cause injury if the front air bags inflate.
Front seat-mounted side-impact supplemental air bag and roof- mounted curtain side-impact supplemental air bag systems The side air bags are located in the outside of the seatback of the front seats. The curtain air bags are located in the side roof rails.
● Right after inflation, several side air bag and curtain air bag system components will be hot. Do not touch them; you may severely burn yourself. ● No unauthorized changes should be made to any components or wiring of the side air bag and curtain air bag systems.
The pretensioner system activates in conjunction with the front air bag system. Working with the seat belt retractor, it helps tighten the seat belt when the vehicle becomes involved in certain types of collisions, helping to restrain front seat occupants.
SUPPLEMENTAL AIR BAG WARNING LIGHT The supplemental air bag warning light, displaying in the instrument panel, moni- tors the circuits of the supplemental front-impact air bag, front seat-mounted side-impact supple- mental air bag, roof-mounted curtain side-impact supplemental air bag and seat belt pretensioner systems.
● The front air bag, side air bag, curtain air bag systems and the pretensioner system should be inspected by a NISSAN dealer if there is any damage to the front end or side portion of the vehicle. ● If you need to dispose of the supple- mental air bag or pretensioner systems or scrap the vehicle, contact a NISSAN dealer.
2 Instruments and controls Instrument panel ...................................2 - 2 Meters and gauges ................................2 - 3 Speedometer and odometer .....................2 - 4 T achometer ....................................2 - 5 Engine coolant temperature gauge .
Windows ........................................ 2-41 P ower windows ............................... 2-41 Moonroof (if so equipped) ......................... 2-44 Automatic moonroof ........................... 2-44 Dual Panel Moonroof (if so equipped) .
1. Side and center vents (P . 4-34) 2. Headlight/fog light/turn signal switch (P . 2-27) 3. Steering wheel switch for audio control and Bluetooth 姞 Hands-Free Phone System (if so equipped) (P . 4-84, 4-88) 4. Meters and gauges (P . 2-3) 5. Driver supplemental air bag/horn (P .
24. Rear control cancel switch (if so equipped) (P . 2-47) 25. V ehicle Dynamic Control (VDC) OFF switch (P . 2-35) 26. Outside mirror controls (P . 3-27) 27. Heated steering wheel switch (if so equipped) (P . 2-34) 28. T runk lid release switch (P . 3-20) * Refer to the separate Navigation System Owner’s Manual (if so equipped) .
SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates the vehicle speed. Odometer/T win trip odometer The odometer/twin trip odometer is displayed when the ignition switch is placed in the ON position. The odometer 䊊 1 records the total distance the vehicle has been driven.
T ACHOMETER The tachometer indicates engine speed in revo- lutions per minute (rpm) . Do not rev the engine into the red zone 䊊 1 . CAUTION When engine speed approaches the red zone, shift to a higher gear or reduce en- gine speed. Operating the engine in the red zone may cause serious engine damage.
FUEL GAUGE The gauge indicates the approximate fuel level in the tank. The gauge may move slightly during braking, turning, acceleration, or going up or down hills. The gauge needle returns to E (Empty) after the ignition is placed in the OFF position.
COMPASS DISPLAY Push the button for about 1 second when the ignition switch is placed in the ON position to toggle the outside temperature and compass direction display 䊊 1 on or off. The display will indicate the direction that the vehicle is heading.
Zone variation change procedure The difference between magnetic north and geo- graphical north is known as variance. In some areas, this difference can sometimes be great enough to cause false compass readings. Follow these instructions to set the variance for your particular location if this happens: 1.
1. With the display turned on, press and hold the button for about 13 seconds or the for about 10 seconds. The “C” icon in the compass display will illuminate. 2. Calibrate the compass by driving the vehicle in three complete circles at a maximum speed of 5 MPH (8 km/h) .
or Anti-lock Braking System (ABS) warning light Supplemental air bag warning light Malfunction Indicator Light (MIL) or Brake warning light Continuously V ariable T ransmission (CVT) indicator light S.
If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly . Have the system checked by a NISSAN dealer. If an ABS malfunction occurs, the anti-lock func- tion is turned off.
CAUTION Running the engine with the engine oil pressure warning light on could cause se- rious damage to the engine almost imme- diately. Such damage is not covered by warranty.
● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.
WARNING If the supplemental air bag warning light is on, it could mean that the front air bag, side air bag, curtain air bag systems (if so equipped) and/or pretensioner systems will not operate in an accident. T o help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible.
vehicle is not ready for an emission control sys- tem inspection/maintenance test. See “Readi- ness for inspection/maintenance (I/M) test” in the “T echnical and consumer information” section of this manual.
Push the V ehicle Dynamic Control off switch again or restart the engine and the system will operate normally. See “Vehicle Dynamic Control (VDC) system” in the “Starting and driving” sec- tion of this manual. The Vehicle Dynamic Control light also comes on when you push the push-button ignition switch to the ON position.
HOW TO USE THE VEHICLE INFORMATION DISPLAY Press the button, located on the instru- ment panel just behind the steering wheel, to display the following modes: MPG → MPG/MPH → Time/Miles → Range .
Time/Miles (km) mode The time/miles (km) mode can be selected to show the time and distance driven since the last reset. Range mode The range mode can be selected to give you an estimation of the distance that can be driven before refueling.
Setting mode The setting mode allows you to set reminders or preferences for alerts, maintenance intervals or language displays. In the setting mode screen press to move to: ● Alert ● Maintenance ● Display and press to select the menu. Alert mode The alert mode allows you to set alerts notifying you of time to rest or icy conditions.
Maintenance mode The maintenance mode allows you to set alerts for the reminding of maintenance intervals for the following: ● engine oil ● oil filter ● tires ● other Set a desired interval by pushing to high- light the maintenance field and pressing .
V ehicle information display warnings and indicators 1. Door and trunk open warning 2. Push warning 3. Low fuel warning 4. Low windshield washer fluid warning 5. No key warning 6. Parking brake warning 7. Shift P warning 8. Engine start operation indicator 9.
Door and trunk open warning This warning illuminates when a door or the trunk has been opened when the engine is running. Push warning After the Shift P warning illuminates, the Push warning will illuminate if the ignition switch is placed in the ACC position when the shift selec- tor is moved to the P (Park) position.
NISSAN Intelligent Key™ insertion indica- tor This indicator illuminates when the Intelligent K ey needs to be inserted into the Intelligent Key port. (For example, the Intelligent Key battery is dis- charged.) If this indicator illuminates, insert the Intelligent K ey into the Intelligent Key port in the correct direction.
ways secure your vehicle even if parking for a brief period. Never leave your Intelligent K ey in the vehicle, and always lock the vehicle when unattended.
3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key . If the no start condition re-occurs, NISSAN rec- ommends placing the registered key on a sepa- rate key ring to avoid interference from other devices.
NO TE: Y ou can turn on or turn off the driving speed dependent intermittent wiper func- tion for vehicles with navigation system. Refer to “V ehicle electronic systems” in the “Display screen, heater, air conditioner, au- dio and phone systems” section later in this manual.
NO TE: The top few rows of wires on the rear win- dow are not part of the rear window de- froster system. These wires make up the antenna for the audio system. X ENON HEADLIGHTS (if so equipped) WARNING Ꮨ HIGH VOL T AGE ● When xenon headlights are on, they produce a high voltage.
HEADLIGHT CONTROL SWITCH Lighting 䊊 1 When turning the switch to the posi- tion, the front parking, tail, license plate and instrument panel lights come on. 䊊 2 When turning the switch to the posi- tion, the headlights come on and all the other lights remain on.
Autolight system The autolight system allows the headlights to be set so they turn on and off automatically. The autolight system can: ● T urn on the headlights, front parking, tail, license plate and instrument panel lights au- tomatically when it is dark.
Headlight beam select 䊊 1 T o select the high beam function, push the lever forward. The high beam lights come on and the light illuminates. 䊊 2 Pull the lever back to select the low beam. 䊊 3 Pulling and releasing the lever flashes the headlight high beams on and off.
INSTRUMENT BRIGHTNESS CONTROL The instrument cluster illuminates when the igni- tion switch is in the ON position. The instrument brightness control operates when the headlight control switch is in the AUT O, or position. T urn the control left or right to adjust the bright- ness of the instrument panel lights when driving at night.
Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights flash. WARNING ● If stopping for an emergency, be sure to move the vehicle well off the road.
The climate controlled seat warms up or cools down the front seat by blowing warm or cool air from the surface of the seat. The climate control switch is located on the center console. The climate controlled seat can be operated as follows: 1. Start the engine.
The front seats are warmed by built-in heaters (if so equipped) . The switch is located on the center console. 1. Start the engine. 2. Push the L O or HI position of the switch, as desired. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off.
Push the switch again to turn the heated steering wheel system off manually . The indicator light will go off. NO TE: If the surface temperature of the steering wheel is above 68°F (20°C) when the switch is turned on, the system will not heat the steering wheel.
The power outlets are for powering electrical accessories such as cellular telephones. They are rated at 12 V olt, 120 W (10A) maximum. The power outlet in the front console box is powered directly by the vehicle battery .
SEATBACK POCKETS The seatback pockets are located on the back of the driver’s and passenger’s seats. The pockets can be used to store maps. SUNGLASSES HOLDER (if so equipped) T o open the sunglasses holder, push and release. WARNING ● Keep the sunglasses holder closed while driving to prevent an accident.
CUP HOLDERS CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. ● Use only soft cups in the cup holder. Hard objects can injure you in an accident.
GLOVE BOX Open the glove box by pulling the handle. Use the mechanical key when locking 䊊 1 or unlocking 䊊 2 the glove box. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop. CONSOLE BOX Upper half Pull up on the driver’s side latch to open the upper half of the console box.
GROCERY HOOKS The grocery hooks are located in the trunk and can be used to hang a standard size plastic grocery bag. CAUTION Do not apply a total load of more than 20 lbs (9 kg) to a single grocery hook. CARGO NETS (if so equipped) WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting.
T o install a cargo net, attach the net to the retain- ers. T o remove a cargo net, detach the net from the retainers. P OWER WINDOWS WARNING ● Make sure that all passengers have their hands, etc . inside the vehicle while it is in motion and before closing the windows.
Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close all of the windows. T o open a window , push the switch to the first detent and continue to hold down until the de- sired window position is reached.
Automatic operation T o fully open a window equipped with automatic operation, press the window switch down (only driver’s side shown) to the second detent and release it; it need not be held. The window auto- matically opens all the way. T o stop the window, lift the switch up while the window is opening.
AUTOMATIC MOONROOF The moonroof will only operate when the ignition switch is placed in the ON position. The auto- matic moonroof is operational for about 45 sec- onds, even if the ignition switch is placed in the ACC or OFF position.
When closing: If the control unit detects something caught in the moonroof as it moves to the front, the moonroof will immediately open backward. When tilting down: If the control unit detects something caught in the moonroof as it tilts down, the moonroof will im- mediately tilt up.
● T o tilt the moonroof down and close the sunshade at the same time, push the switch 䊊 2 to the close position until it reaches the second detent.
Sunshade T o open the sunshade: ● T o fully open the sunshade, push the switch 䊊 1 toward the open position until it reaches the first detent. ● T o fully open the sunshade and the moon- roof together, push the switch 䊊 1 toward the open position until it reaches the second detent.
The rear sun shade operates when the ignition switch is in the ACC or ON position. The rear sun shade switch is located on the front console. ● T o raise the sun shade, push the upper side of the switch 䊊 1 . ● T o lower the sun shade, push the lower side of the switch 䊊 2 .
Lights remain on for a maximum of 30 seconds. – Driver’s door is opened. Lights remain on for a maximum of 30 seconds after driver’s door is closed. – Ignition switch is placed in the OFF posi- tion. Lights remain on for a maximum of 30 seconds.
FRONT T o turn the map lights on, press the switches. T o turn them off, press the switches again. CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery. REAR T o turn on the rear lights, press and release the switch 䊊 1 .
The light illuminates when the trunk lid is opened. When the trunk lid is closed, the light goes off. The light will go off after about 30 minutes if the trunk lid is left open, unless the ignition switch is in the ON position.
PROGRAMMING HOMELINK 姞 1. T o begin, press and hold the two outer HomeLink 姞 buttons (to clear the memory) until the indicator light 䊊 1 blinks (after 20 seconds) . Release both buttons. 2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLink 姞 surface.
7. Within 30 seconds of pressing and releas- ing the garage door opener’s program but- ton, quickly and firmly press and release the HomeLink 姞 button you’ve just programmed. Press and release the HomeLink 姞 button up to 3 times to complete the training.
REPROGRAMMING A SINGLE HOMELINK 姞 BUTTON T o reprogram a HomeLink 姞 Universal T ransceiver button, complete the following. 1. Press and hold the desired HomeLink 姞 but- ton.
3 Pre-driving checks and adjustments K e y s .............................................3 - 2 NISSAN Intelligent K ey™ ........................3 - 2 NISSAN V ehicle Immobilizer System keys .........3 - 3 Doors .....................................
1. T wo Intelligent K eys 2. Mechanical keys with built-in transpon- der chip (inside Intelligent K eys) 3. K ey number plate NISSAN INTELLIGENT K EY™ Y our vehicle can only be driven with the Intelligent K eys which are registered to your vehicle’s Intel- ligent K ey system components and NISSAN V e- hicle Immobilizer System components.
Mechanical key The Intelligent Key contains the mechanical key , which can be used in case of a discharged bat- tery . T o remove the mechanical key, release the lock knob on the back of the Intelligent K ey. T o install the mechanical key , firmly insert it into the Intelligent Key until the lock knob returns to the lock position.
Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle. Do not allow the immobilizer system key, which contains an electrical transponder, to come into contact with salt water. This could affect system function.
Opening and closing windows The driver’s door key operation allows you to open and close windows equipped with auto- matic operation at the same time. ● T o open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked.
Lockout protection When the power door lock switch (driver’s or front passenger’s side) is moved to the lock position with the Intelligent K ey in the port and any door open, all doors will lock and unlock automatically .
4. When activated, the hazard indicator will flash twice. When deactivated, the hazard indicator will flash once. 5. The ignition switch must be placed in the OFF and ON position again between each setting change. WARNING ● Radio waves could adversely affect electric medical equipment.
● When the vehicle is parked near a parking meter. In such cases, correct the operating conditions before using the Intelligent K ey function or use the mechanical key . Although the life of the battery varies depending on the operating conditions, the battery’s life is approximately 2 years.
OPERATING RANGE The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range from the request switch 䊊 1 .
● Do not pull the door handle before pushing the door handle request switch. The door will be unlocked but will not open. Release the door handle once and pull it again to open the door. NISSAN INTELLIGENT K EY™ OPERATION Y ou can lock or unlock the doors without taking the key out of your pocket or bag.
NO TE: ● Doors lock with the door handle request switch when the ignition switch is placed in the ON position. ● Doors lock with the door handle request switch while the ignition switch is not in the L OCK position. ● Doors do not lock by pushing the door handle request switch while any door is open.
Unlocking doors 1. Carry the Intelligent Key . 2. Push the door handle request switch 䊊 1 . 3. The hazard warning lights flash once and the outside buzzer sounds once. 4. Push the door handle request switch 䊊 1 again within 60 seconds to unlock all doors.
Opening the trunk lid 1. Push the trunk opener request switch 䊊 A for more than 1 second while carrying the Intel- ligent K ey with you. 2. The trunk will unlatch.
CAUTION After locking the doors using the Intelli- gent Key, be sure that the doors have been securely locked by operating the door handles. Unlocking doors 1. Push the button on the Intelligent Key . 2. The hazard warning lights flash once. 3. Push the button again within 60 sec- onds to unlock all doors.
Releasing the trunk lid Push the button for longer than 0.5 sec- onds to open the trunk lid. The trunk release button will not operate when the ignition switch is in the ON position or when the trunk cancel switch is in the OFF position. See “Cancel switch” later in this section.
T o deactivate: Press and hold the and buttons for at least 2 seconds. The hazard warning lights will flash 3 times to confirm that the horn beep feature has been deactivated. T o activate: Press and hold the and buttons for at least 2 seconds once more.
Symptom Possible Cause Remedy When pushing the ignition switch to stop the engine The SHIFT P warning appears on the dis- play and the inside warning chime sounds continuously. The shift selector is not in the P (Park) position. Shift the shift selector to the P (Park) position.
䊊 1 Pull the hood lock release handle located below the driver side instrument panel. The hood will spring up slightly . 䊊 2 Push the lever at the front of the hood to the side as illustrated with your fingertips and raise the hood. When closing the hood, lower it slowly and make sure it locks into place.
OPENER OPERATION WARNING ● Do not drive with the trunk lid open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Ex- haust gas” in the “Starting and driving” section of this manual.
SECONDARY TRUNK LID RELEASE (if so equipped) T o open the trunk lid from the rear seat: 䊊 1 ● Fold down the center arm rest. ● Insert the mechanical key into the trunk com- partment access lid lock.
OPENING THE FUEL-FILLER DOOR The fuel-filler door automatically unlocks when all doors are unlocked. 1. Unlock the fuel-filler door using one of the following operations. ● Unlock all doors with the keyfob. ● Unlock all doors with the key. ● Press the power door lock switch to the unlock position.
● Do not fill a portable fuel container in the vehicle or trailer. Static electricity can cause an explosion of flammable liquid, vapor or gas in any vehicle or trailer. T o reduce the risk of serious injury or death when filling portable fuel containers: – Always place the container on the ground when filling.
AUTOMATIC OPERATION (if so equipped) Tilt operation Push the switch 䊊 1 up or down to adjust the steering wheel to the desired position. Entry/Exit function The automatic drive positioner system will make the steering wheel move up automatically when the driver’s door is opened and the ignition switch is in the L OCK position.
WARNING Do not adjust the steering wheel while driving. Y ou could lose control of your vehicle and cause an accident. 䊊 1 T o block glare from the front, swing down the main sun visor. 䊊 2 T o block glare from the side, remove the main sun visor from the center mount and swing the visor to the side.
V ANITY MIRRORS T o access the vanity mirror, pull the sun visor down and flip open the mirror cover. The vanity mirror will illuminate when the mirror cover is open.
T ype B and T ype C The indicator light 䊊 2 will illuminate when the automatic anti-glare feature is operating. T o turn off the automatic anti-glare feature, press: ● the O button for inside mirrors without compass. ● the button for inside mirrors with compass.
OUTSIDE MIRRORS The outside mirror remote control will operate only when the ignition switch is in the ACC or ON position. Move the small switch 䊊 1 to select the right or left mirror. Adjust each mirror to the desired position using the large switch 䊊 2 .
Foldable outside mirrors Pull the outside mirror toward the door to fold it. Reverse tilt-down feature (if so equipped) The reverse tilt-down feature will turn both out- side mirror surfaces downward to provide better rear visibility close to the vehicle.
MEMORY STORAGE FUNCTION T wo positions for the driver’s seat, steering col- umn, and outside mirrors can be stored in the automatic drive positioner memory. Follow these procedures to use the memory system. 1. Set the Continuously V ariable T ransmission (CVT) shift selector to the P (Park) position.
6. Move the shift selector to R (Reverse) . 7. Adjust the mirror to the desired viewing po- sition for backing up by operating the out- side mirror control switch. 8. Push the SET switch and, within 5 seconds, push the memory switch 1 or 2 selected in step 3.
The entry/exit function can be adjusted or can- celed. See “Comfort & Convenience settings” in the “Monitor, climate, audio, phone and voice recognition systems” section of this manual. Restarting the entry/exit function If the battery cable is disconnected or if the fuse opens, the entry/exit function will be disabled.
4 Monitor, climate, audio, phone and voice recognition systems Control panel buttons — color screen without Navigation System (if so equipped) ..................4 - 2 How to use the NISSAN controller ...............4 - 3 How to select menus on the screen .
CompactFlash™ (CF) player operation (if so equipped) ............................... 4-70 iP od 姞 * Player Operation (if so equipped) ......... 4-73 Music Box hard-disk drive audio system (if so equipped) ............................... 4-74 CD/CF (CompactFlash™) care and cleaning .
WARNING ● Positioning of the heating or air condi- tioning controls and display controls should not be done while driving in or- der that full attention may be given to the driving operation. ● Do not disassemble or modify this sys- tem. If you do, it may result in accidents, fire, or electrical shock.
CAUTION ● The glass screen on the liquid crystal display may break if it is hit with a hard or sharp object. If the glass breaks, do not touch the liquid crystalline material, which contains a small amount of mer- cury. In case of contact with skin, wash immediately with soap and water.
If you press the BACK button 䊊 4 during setup, the setup will be canceled and/or the display will return to the previous screen. ● Finish setup. In some screens pressing the BACK button 䊊 4 accepts the changes made during setup. HOW TO SELECT MENUS ON THE SCREEN V ehicle functions are viewed on the center dis- play screen in menus.
HOW TO USE THE INFO BUTTON Press the INFO button. The display screen shows vehicle information for your convenience. The information shown on the screen should be a guide to determine the condition of the vehicle.
Fuel economy record Press the INFO button, then select the “Fuel Economy” key , then select the “View” key using the NISSAN controller and press the ENTER button. The average fuel consumption history will be displayed in a graph form along with the average fuel for the previous Reset-to-Reset period.
Displaying the maintenance notice re- minder Select the “Interval Reminder ON” key and press the ENTER button to display the MAINTENANCE INFORMA TION automatically at the set mainte- nance interval. The indicator light will illuminate when it is ON.
Display settings Select the “Display” key and press the ENTER button. The Display settings screen will appear. Brightness/contrast : Select the “Brightness” key or the “Contrast” key to adjust the brightness or contrast of the map background.
T o turn the screen on: ● Press the SETTING button and select the “Display” key and then select the “Display ON” key. Then set the screen to on by press- ing the ENTER button, or ● Hold th.
Daylight Savings Time: When this item is enabled (indicator light illumi- nated) , daylight savings time is on. T o turn off the daylight savings time, touch the “ON” key; the amber indicator light will disappear. Time Zone: Select the “Time Zone” key; the Time Zone screen will appear.
Clock Adjust : Adjust the time by manually inputting the correct time. ● 0–9 : Select to change the number in the display . ● Modify: Select to change the number at the cursor position. ● >: Select to move the cursor position to the right. ● <: Select to move the cursor position to the left.
Auto Interior Illumination: Select to turn on or turn off the illumination of the interior lights when any door is unlocked. Auto Headlights Sensitivity: Select to adjust the sensitivity of the automatic headlights higher (right) or lower (left) .
Language / Units Use the NISSAN controller to select the “Lan- guage / Units” key and press the ENTER button. Select which setting you want to change using the NISSAN controller and selecting either the “Select Language” key or the “Select Units” key by pressing the ENTER button.
OFF BUTTON T o change the display brightness, press the OFF button. Pressing the button again will change the display to the day or the night display . Then, adjust the brightness by using the NISSAN controller. The display brightness can also be adjusted us- ing the + (brighter) button or the ⫺ (dimmer) button.
9. OFF brightness control button (P . 4-28) 10. - (brightness control) button 11. VOICE button* 12. SETTING button (P . 4-22) 13. MAP button* 14. BACK (previous) button (P . 4-15) 15. ZOOM IN button* *For Navigation system control buttons, refer to the separate Navigation System Owner’s Manual.
If you press the BACK button 䊊 4 during setup, the setup will be canceled and/or the display will return to the previous screen. ● Finish setup. In some screens pressing the BACK button 䊊 4 accepts the changes made during setup. For the VOICE button 䊊 5 functions, refer to the separate Navigation System Owner’s Manual.
Adjusting the item: T ouch the “+” key 䊊 1 or the “ ⫺ ” key 䊊 2 to adjust the settings. T ouch the “UP” key 䊊 3 to scroll up to the previous page, or touch the “DOWN” key 䊊 4 to scroll down to next page. Inputting characters: T ouch the letter or number key 䊊 1 .
HOW TO SELECT MENUS ON THE SCREEN V ehicle functions are viewed on the center dis- play screen in menus. Whenever a menu selec- tion is made or menu item is highlighted, different areas on the screen provide you with important information. See the following for details.
Fuel economy Press the INFO button, then select the “Fuel Economy” key using the NISSAN controller and press the ENTER button to display Average Fuel Economy , Distance to Empty and Fuel Economy Record.
Maintenance items Press the INFO button and select the “Mainte- nance” key using the NISSAN controller and press the ENTER button; the maintenance infor- mation will be displayed on the screen.
Displaying the maintenance notice re- minder Select the “Interval Reminder ON” key and press the ENTER button to display the MAINTENANCE INFORMA TION automatically at the set mainte- nance interval. The indicator light will illuminate when it is ON.
HOW TO USE THE SETTING BUTTON When the SETTING button is pressed, the SET - TINGS screen will appear on the display . Y ou can select and/or adjust several functions, features and modes that are available for your vehicle. Use the NISSAN controller to select each item to be set and press the ENTER button.
Display off: Select the “Display ON” key. The indicator of the “Display ON” turns amber and the message above will be displayed briefly . When the audio, HV AC (Heater and air conditioner) , or any mode button on the control panel is operated, the dis- play turns on for that operation.
Clock Format : Choose either the 12h (12–hour) clock display or the 24h (24–hour) clock display . Offset Adjust : Adjust the time by increasing or decreasing per minute. Daylight Saving Time: When this item is enabled (indicator light illumi- nated) , daylight saving time is on.
Comfort & Convenience settings Select the “Comfort & Conv .” key by using the NISSAN controller and pressing the ENTER but- ton. The comfort and convenience option screen will be displayed. Y ou can set the following operating conditions by selecting the desired item using the NISSAN controller, then pressing the ENTER button.
Slide Driver Seat Back on Exit: Select to turn on or turn off the driver’s seat moving backwards for easy exit when the ignition switch is in the OFF position and the driver’s door is opened. After getting into the vehicle and pushing the ignition switch to the ACC position, the driver’s seat moves to the previous position.
Select Language: Select the “English” key or the “Français” key to change the language shown on the display . If you select the “Français” key, French language will be displayed so please use the French Own- er’s Manual.
Beep setting With this option on (indicator light illuminated), a beep will sound if any control panel button is pressed. Phone settings For phone settings refer to “Bluetooth 姞 Hands- Free Phone System with Navigation System (if so equipped)” later in this section.
● Do not put anything on the rear view camera. The rear view camera is in- stalled above the license plate. ● When washing the vehicle with high- pressure water, be sure not to spray it around the camera. Otherwise, water may enter the camera unit causing wa- ter condensation on the lens, a mal- function, fire or an electric shock.
● If the battery is disconnected or be- comes discharged, the predicted course lines may be displayed incor- rectly. If this occurs, please perform the following procedures: – T urn the steering wheel from lock to lock while the engine is running.
3. Slowly back up the vehicle adjusting the steering wheel so that the predicted course lines 䊊 B enter the parking space 䊊 C . 4. Maneuver the steering wheel to make the vehicle width guide lines 䊊 D parallel to the parking space 䊊 C while referring to the pre- dicted course lines.
the hill is viewed in the monitor further than it appears. Backing up on a steep downhill When backing up the vehicle down a hill, the distance guide lines and the vehicle width guide lines are shown further than the actual distance. For example, the display shows 3 ft (1.
Backing up near a projecting object The predicted course lines 䊊 A do not touch the object in the display. However, the vehicle may hit the object if it projects over the actual backing up course. Backing up behind a projecting object The position 䊊 C is shown further than the position 䊊 B in the display.
● When the temperature is extremely high or low , the screen may not clearly display ob- jects. This is not a malfunction. ● When strong light directly enters the cam- era, objects may not be displayed clearly. This is not a malfunction. ● V ertical lines may be seen in objects on the screen.
Side LHA1133 Rear LHA1134 Monitor, climate, audio, phone and voice recognition systems 4-35 墌 REVIEW COPY— 2009 Maxima (max) Owners Manual—USA_English (nna) 11/03/08—debbie 墍.
1. T emperature control buttons (driver’s side) 2. AUT O climate control ON button 3. (front defroster) button 4. Air recirculation button 5. MODE (manual air flow control) button 6. T emperature control buttons (passen- ger’s side) 7. DUAL (passenger side temperature control) ON/OFF button 8.
AUTOMATIC OPERATION Cooling and/or dehumidified heating (AUT O) This mode may be used all year round as the system automatically works to keep a constant temperature. Air flow distribution and fan speed are also controlled automatically . 1. Push the AUTO button on.
The air recirculation cannot be activated when the air conditioner is in the front defrosting mode or the front defrosting and foot out- let mode. Fresh air intake Push the fresh air intake button to draw outside air into the passenger compartment. The indicator light on the button will come on.
1. T emperature control dial (driver’s side)/ AUT O (automatic) climate control ON button 2. A/C (air conditioner) ON/OFF button 3. Air recirculation button 4. Fresh air intake button 5. MODE (manual air flow control) button 6. T emperature control buttons (passen- ger’s side)/DUAL (passenger’s side temperature control) ON/OFF button 7.
AUTOMATIC OPERATION Cooling and/or dehumidified heating (AUT O) This mode may be used all year round as the system automatically works to keep a constant temperature. Air flow distribution and fan speed are also controlled automatically . 1. Push the AUTO button on.
The air recirculation cannot be activated when the air conditioner is in the front defrosting mode or the front defrosting and foot out- let mode. Fresh air intake Push the fresh air intake button to draw outside air into the passenger compartment. The indicator light on the button will come on.
The rear seat passengers can adjust the climate control system using the climate controls in the rear armrest panel. 1. AUT O button 2. button 3. switch For information on canceling the rear seat con- troller, see “Rear control cancel switch (if so equipped)” in the “Instruments and controls” sec- tion.
The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner.
Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter) , static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response.
Compact disc (CD) player CAUTION ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player. ● T rying to load a CD with the CD door closed could damage the CD and/or CD changer. ● Only one CD can be loaded into the CD player at a time.
● The CF player sometimes cannot function when the passenger compartment tempera- ture is extremely high. Decrease the tem- perature before use. ● Do not expose a CF card to direct sunlight. ● Confirm that a CF card is inserted correctly . iP od 姞 * player (if so equipped) ● Some characters used in other languages (Chinese, Japanese, etc.
Compact Disc (CD)/CompactFlash™ (CF) with MP3 or WMA T erms: ● MP3 — MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well-known compressed digital audio file format. This format allows for near “CD quality” sound, but at a fraction of the size of normal audio files.
● If there is a file in the top level of the disc, “Root Folder” is displayed. ● The playback order is the order in which the files were written by the writing software.
Specification chart : Supported media CD, CD-R, CD-RW , CF Supported file systems CD, CD-R, CD-RW: ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. CompactFlash card: F A T12, FA T16, FA T32 Supported versions*1 MP3 V ersion MPEG1, MPEG2, MPEG2.
T roubleshooting guide: Symptom Cause and Countermeasure Cannot play Check if the CD/CF was inserted correctly . Check if the CD/CF is scratched or dirty . Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player.
1. CD eject button 2. VOL/ON·OFF control knob 3. Station and CD select (1 - 6) buttons 4. L OAD CD button 5. TUNE/FOLDER and AUDIO control knob (Bass, T reble, Fade, Balance, SSV (if so equipped) , and Beep) 6. AUX IN jack 7. AUX button 8. TRACK button 9.
AUDIO control knob (Bass, Treble, Fade, Balance, SSV and Beep) : Press the AUDIO control knob to change the mode as follows: Bass → T reble → Fade → Balance → Beep ON/OFF → Bass T o adjust Bass, T reble, Fade and Balance, press the AUDIO control knob until the desired mode appears in the display.
● Artist name displays the name of the artist of the song playing. ● Album title displays the title of the album of the song playing. FM/AM radio operation FM/AM band select : Pressing the AM·FM .
T o insert 6 CDs to the CD changer, press the L OAD button for more than 1.5 seconds. The slot numbers (1 – 6) will illuminate on the display when CDs are loaded into the changer. DISC button: When the DISC button is pressed with the sys- tem off and the compact disc loaded, the system will turn on and the compact disc will start to play .
SCAN button: While listening to a CD, press the SCAN button to preview the first 10 seconds of each track on the CD playing. Pressing the SCAN button again during this 10 second period stops the scan and the CD remains on that track. CD EJECT: Current/Selected disc: ● Press the button, then press the slot number (1 – 6) for the desired disc.
1. CD eject button 2. VOL/ON·OFF control knob 3. Station and CD select (1 - 6) buttons 4. L OAD CD button 5. TUNE/FOLDER and AUDIO control knob (Bass, T reble, Fade and Balance) 6. AUX button 7. TRACK button 8. SEEK/CA T button 9. DISC button 10. RPT/RDM button 11.
FM/AM/SA T RADIO WITH COMPACT DISC (CD) CHANGER (if so equipped) For all operation precautions, see ⬙ Audio opera- tion precautions ⬙ earlier in this section.
For information on how to use the NISSAN con- troller, see “How to use the NISSAN controller” earlier in this section. Clock operation For additional information on setting the clock, see “ Adjusting the time” earlier in this section.
FM/AM/SA T radio operation FM/AM band select : Pressing the AM·FM button will change the band as follows: AM → FM1 → FM2 → AM When the AM·FM button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played.
If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Radio data system (RDS) : RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band) .
When the CD button is pressed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play . When the CD button is pressed with the com- pact disc loaded with the tape or the radio play- ing, the tape or radio will automatically be turned off and the compact disc will start to play .
CD IN indicator: The slot numbers (1 – 6) will illuminate if CDs have been loaded into the changer in CD mode only . AUX (auxiliary) input jacks The auxiliary input jacks are located inside the center console 䊊 1 . NTSC compatible devices such as video games, camcorders and portable video players can be connected to the auxiliary input jacks.
AUX settings Select the “Settings” key using the NISSAN con- troller and press the ENTER button. Choose one of the display modes by selecting the “ ” key or the “ ” key: ● Normal ● Wid.
1. CD eject button 2. VOL/ON·OFF control knob 3. Station select (1 - 6) buttons 4. TUNE/FOLDER and AUDIO control knob (Bass, T reble, Fade and Balance) 5. CompactFlash insert slot 6. DISC·AUX button 7. TRACK button 8. SEEK/CA T button 9. SA T* button 10.
FM/AM/SA T RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) For all operation precautions, see ⬙ Audio opera- tion precautions ⬙ earlier in this section.
For information on how to use the NISSAN con- troller, see “How to use the NISSAN controller” earlier in this section. Clock operation For additional information on setting the clock, see “ Adjusting the time” earlier in this section.
FM/AM/SA T radio operation FM/AM band select : Pressing the AM·FM button will change the band as follows: AM → FM1 → FM2 → AM When the AM·FM button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played.
If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Radio data system (RDS) : RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band) .
CD select buttons: T o play another CD that has been loaded, press a CD select button (1 – 6) . CD EJECT button: When the button is pressed with the com- pact disc loaded, the compact disc will be ejected. When button is pressed while the com- pact disc is being played, the compact disc will eject and the system will turn off.
AUX settings Select the “Settings” key using the NISSAN con- troller and press the ENTER button. Choose one of the display modes by selecting the “ ” key or the “ ” key: ● Normal ● Wid.
DISC·AUX button: When the DISC·AUX button is pressed with the system off and the CF card inserted, the system will turn on. If another audio source is playing and a CF card is inserted, press the DISC·AUX but- ton repeatedly until the center display changes to the CompactFlash™ mode.
SEEK/CA T and TRACK buttons: Press the SEEK/CA T button or the TRACK button while the CF card is being played, the next track or the beginning of the current track on the CF will be played. Press and hold the SEEK/CA T (rewind) button or the TRACK (fast forward) button for more than approximately 1.
iP od 姞 * PLAYER OPERATION (if so equipped) Connecting iP od 姞 Open the center console lid and open the iP od 姞 cover. Connect the cable 䊊 1 as illustrated, and then connect the other end of the cable to your iP od 姞 䊊 2 . Y our vehicle is equipped with the spe- cialized cable for connecting the iPod 姞 to your vehicle audio unit.
● Albums ● Artists ● Genres ● Composers ● Audiobooks The following keys shown on the screen are also available: ● MENU: returns to the previous screen. ● : plays/pauses the music selected. SEEK/CA T and TRACK buttons: When the SEEK/CA T button or TRACK button is pressed for less than 1.
Recording CDs 1. Operate the audio system to play a CD. For information on playing CDs, see “Com- pact Disc (CD) player operation” earlier in this section. 2. T ouch the “REC” key . REC CD appears on the screen. NO TE: ● The system starts playing and recording the 1st track on the CD when the “REC” key is selected.
Playing recorded songs Select the Music Box audio system by using one of the following methods: ● Press the SOURCE select switch on the steering wheel. For information, see “Steering wheel switch for audio control” later in this section. ● Press the DISC·AUX button repeatedly until the center display changes to the Music Box mode.
Music Box menu There are some options available during play- back. T ouch the “Menu” key , then select one of the following that are displayed on the screen, if necessary . Refer to the following information for each item: ● Play by Artist Plays songs by an artist whose music is currently being played.
● Search Albums Displays a list of albums in order of the date when they were stored in the system. Se- lecting an album displays all of the tracks on the album and starts playing the first track. T ouch the “Sort” key to re-sort albums in one of the following order: – Rec.
● T ransfer Missing Titles to CF T ransfers the information of the album re- corded without titles to a CompactFlash™ card. Visit www .nissanusa.com/gracenote/ for details. – Music Box Settings For information, see “Music Box settings” later in this section.
Restoring deleted data Deleted music data can be restored by perform- ing the following: 1. T ouch the “Menu” key and then the touch the “Music Box System Info.” key on the screen. 2. T ouch the “Deleted Items” key and then the “ Album/T rack” key.
Music Box settings T o set up the Music Box hard-disk drive audio system to your preferred settings, touch the “Menu” key during playback, then touch the “Mu- sic Box System Info.
GRACENO TE SOFTW ARE, OR GRACENO TE SERVERS, EXCEPT AS EXPRESSL Y PERMIT - TED HEREIN. Y ou agree that your non-exclusive license to use the Gracenote Data, the Gracenote Software, and Gracenote Servers will terminate if you vio- late these restrictions.
CD/CF (CompactFlash™) CARE AND CLEANING CD: ● Handle a CD by its edges. Do not bend the disc. Never touch the surface of the disc. ● Always place the discs in the storage case when they are not being used. ● T o clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth.
● Do not store the cards in highly humid loca- tions. ● Do not expose the cards to direct sunlight. ● Do not spill any liquids on the cards. Refer to the CompactFlash™ card Owner’s Manual for more details. 1. P ower on and SOURCE select switch 2.
SOURCE select switch Push the source select switch to change the mode in the following sequence: AM → FM → iP od 姞 *4 (if so equipped) → Music Box*2 (if so equipped) → CD*1 → CompactFlash™*1 (if so equipped) → AUX*3. *1: These modes are only available when com- patible media storage is inserted into the device.
1. VOL (volume) control switch 2. TUNE/TRACK switch 3. ON/OFF button 4. SRC (source) select button 5. Display REAR AUDIO CONTROLS (if so equipped) The audio system can also be operated using the rear controls.
ANTENNA Window antenna The antenna pattern is printed inside the rear window . CAUTION ● Do not place metalized film near the rear window glass or attach any metal parts to it. This may cause poor recep- tion or noise. ● When cleaning the inside of the rear window, be careful not to scratch or damage the rear window antenna.
WARNING ● Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.
module when the ignition switch is placed in the ON position with the paired cellular phone turned on and carried in the vehicle. Y ou can register up to 5 different Bluetooth 姞 cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time.
BLUETOOTH 威 is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Visteon. USING THE SYSTEM The NISSAN Voice Recognition system allows hands-free operation of the Bluetooth 姞 Phone System. If the vehicle is in motion, some commands may not be available so full attention may be given to vehicle operation.
● T o speed the operation you can say multiple commands. For example, press the button then say “Phonebook, New entry” rather than “Phonebook.” W ait for the voice feedback prompt then say “New entry” . How to say numbers NISSAN V oice Recognition requires a certain way to speak numbers in voice commands.
CONTROL BUTTONS The control buttons for the Bluetooth 姞 Hands- Free Phone System are located on the steering wheel. PHONE/SEND Press the button to initiate a VR session or answer an incoming call. Y ou can also use the button to skip through system feedback and to enter commands during a call.
Pairing procedure NO TE: The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. Main Menu “Setup” 䊊 A “Pair phone” 䊊 B “New phone” 䊊 C Initiate from handset 䊊 D Name phone 䊊 E Assign priority 䊊 F Choose ringtone 䊊 G 1.
3-digit prefix and the last 4-digits. For ex- ample, 555-121-3354 can be said as “five five five” as the 1st group, then “one two one” as the 2nd group, and “three three five four” as the 3rd group. For dialing more than 10 digits or any special characters, say “In- ternational” .
See “Phone book” later in this section to learn how to store entries. When prompted by the system, say the name of the phone book entry you wish to call. The system acknowledges the name. If there are multiple locations associated with the name, the system asks you to choose the loca- tion.
NO TE: If a call is ended or the cellular phone network connection is lost while the Mute feature is on, the Mute feature will be reset to “off” for the next call so the other party can hear your voice. “Phone book” NO TE: Phone book commands are not available when the vehicle is moving.
.
“Record” 䊊 A The system announces “Recording” and a tone sounds, signaling you to begin. Speak the information you wish to record clearly . When you are done, press the or button on the steering wheel. A tone sounds and the system announces “Memo recorded.
“Select phone” 䊊 C Use the Select Phone command to select a phone of lesser priority when two or more phones paired with Bluetooth 姞 Hands-Free Phone Sys- tem are in the vehicle at the same time. The system asks you to name the phone and confirm the selection.
SPEAKER ADAPTATION (SA) MODE Speaker Adaptation allows up to two out-of- dialect users to train the system to improve rec- ognition accuracy. By repeating a number of commands, the users can create a voice model of their own voice that is stored in the system.
● No ● select ring tone ● dial eight five six nine two ● Bluetooth on ● setup change priority ● call three one nine oh two ● nine seven pause pause three oh eight ● Cancel ● call bac.
T ROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty . If problems are en- countered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved.
WARNING ● Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.
module when the ignition switch is placed in the ON position with the paired cellular phone turned on and carried in the vehicle. Y ou can register up to 5 different Bluetooth 姞 cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time.
REGULATORY INFORMATION FCC Regulatory information – CAUTION: T o maintain compliance with FCC’s RF exposure guidelines, use only the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regula- tions.
NO TE: If a phone is already paired with the sys- tem, Step 1 will not work. T o pair another phone, press the SETTING button, then se- lect the “Phone” key and press the ENTER button. Scroll to the bottom of the list and select the “Bluetooth Setup” key and press the ENTER button.
PHONEBOOK Up to 40 phone numbers can be stored in the phonebook. 1. Press the SETTING button, then select the “Phone” key and press the ENTER button. 2. Select the “Phonebook” key and press the ENTER button. 3. Select one of the “None (Add New)” keys from the name list of the phonebook and press the ENTER button.
There are different methods to input a phone number. Select one of the following options for Step 4 above. Enter Data by Keypad: Input the name and phone number manually us- ing the keypad displayed on the screen. For in- formation on how to use the touch screen, see “How to use the touch screen” earlier in this section.
4. After the call is over, perform one of the following to finish the call: a. Select the “Hang up” key on the Call in Progress screen and press the ENTER button. b. Press the switch on the steering wheel. c. When the Call in Progress screen is dis- played, press the PHONE button on the instrument panel to hang up.
There are some options available when receiving a call. Select one of the following displayed on the screen. Answer: Accept an incoming call to talk. On Hold: Put an incoming call on hold. Reject Call: Reject an incoming call. T o finish the call, follow one of the procedures listed below: a.
ENDING A CALL T o finish the call, perform one of the following procedures: ● Select the “Hang up” key on the Call in Progress display and press the ENTER but- ton. ● Push the switch on the steering wheel. ● When the Call in Progress screen is dis- played press the PHONE button on the in- strument panel to hang up.
● Download All: Download all of the contacts registered in the Bluetooth 姞 cellular phone. Availability of this function depends on each cellular phone. The memory downloading procedure from the cellular phone also varies according to each cellular phone.
● Priority Change If multiple phones are registered to the sys- tem, you can change the priority of the phones on the shown list. The system shows the priority level of each phone. Select phone to change priority . Then, select an- other phone to swap priority levels.
T o access the settings, press the SETTING but- ton, then highlight “V olume and Beeps” using the NISSAN controller and press the ENTER button. Y ou can also adjust the volume of an incoming voice during a call by pushing the volume control switch on the steering wheel or by turning the volume control knob on the instrument panel.
Displaying user guide If you use the NISSAN Voice Recognition system for the first time or you do not know how to operate it, you can display the User Guide for confirmation. Y ou can confirm how to use voice commands by accessing a simplified User Guide, which con- tains basic instructions and tutorials for several voice commands.
Getting started Before using the V oice Recognition system for the first time, you can confirm how to use com- mands by viewing the Getting Started section of the User Guide. 1. Highlight “Getting Started” and press the ENTER button. 2. Y ou can confirm the page by scrolling the screen using the NISSAN controller.
USING THE SYSTEM Initialization When the ignition switch is placed in the ON position, NISSAN V oice Recognition is initialized, which takes a few seconds. When completed, the system is ready to accept voice commands. If the switch is pressed before the initializa- tion completes, voice commands will not be ac- cepted.
Operating tips ● Say a command after the tone. V oice com- mands cannot be accepted when the icon is . ● Commands that are available are always shown on the display and spoken through voice menu prompts. Commands other than those that are displayed are not accepted.
Standard Mode command list Category Command: COMMAND ACTION Phone Displays Phone function commands. Navigation Displays Navigation function commands. Information Displays V ehicle Information.
Phone Command: COMMAND ACTION Dial Number Makes a call to a spoken phone number up to 10 digits. Change Number Corrects the phone number when it is not recognized (available during phone number entry) . Redial Makes a call to the last dialed number. Phonebook Makes a call to a contact that is stored in the Phonebook.
V oice command examples Some basic voice command examples are de- scribed here. For navigation system commands, see the sepa- rate Navigation System Owner’s Manual. Example 1 — Placing a call to the phone number 800-662-6200: 1. Press the switch located on the steering wheel.
4. Say “Dial Number”. 5. Say “800”. 6. The system announces, “Please say the next three digits or dial, or say change number.” 7. Say “662”.
8. The system announces, “Please say the last four digits” or say change number. 9. Say “6200”. 10. The system announces, “Dial or Change Number?” 11.
Example 2 — Placing an international call to the phone number 011-81-111-222-3333: 1. Press the switch located on the steering wheel. 2. The system announces, “Would you like to access Phone, Navigation, Information or Help?” 3. Say “Phone”.
5. Say “011811112223333”. 6. Say “Dial”. 7. The system makes a call to 011-81-111- 222-3333. NO TE: Any digit input format is available in the International Number input process, as well as the special characters such as star (*) , pound (#) , and plus (+) .
Activating Alternate Command Mode 1. Press the SETTING button on the instru- ment panel. 2. Highlight the “Others” key on the display and then press the ENTER button. 3. Highlight the “Voice Recognition” key and then press the ENTER button. 4.
Only manual controls such as the touch screen can navigate the command list menu. As an alternative to the voice command “Help” , you may access the command list using the fol- lowing steps: 1. Press the INFO button on the instrument panel. 2. Highlight the “Others” key using the NISSAN controller and press the ENTER button.
Alternate Command Mode command list Navigation Command: COMMAND ACTION Home Sets a route to your home that is stored in the Address Book. Address Book Displays the first 5 entries of the Address Book. Previous Destinations Sets a route to a previous destination.
COMMAND ACTION North Up Changes the Map display to keep north pointing up on the screen. Zoom In Changes the map scale to a smaller number. Zoom Out Changes the map scale to a larger number. Landmark Icons Shows or hides the points of interests on the displays.
Audio Command: COMMAND ACTION Radio T urns the radio on, selecting the station and band last played. Radio AM T urns to the AM band, selecting the station last played. Radio FM T urns to the FM band, selecting the station last played. Satellite Radio T urns to the SA T band, selecting the station last played.
Displaying user guide Y ou can confirm how to use voice commands by accessing a simplified User Guide, which con- tains basic instructions and tutorials for several voice commands. 1. Press the INFO button on the instrument panel. 2. Highlight the “Others” key using the NISSAN controller and press the ENTER button.
● Placing Calls T utorial for making a phone call by voice command operation. ● Help on Speaking Displays useful tips for how to correctly speak commands in order for them to be properly recognized by the system. ● V oice Recognition Settings Describes the available V oice Recognition settings.
2. A list of commands appears on the screen, and the system announces, “Please say a command from the displayed list or say Help to show all commands.
Say , “six two zero zero” . Using this method of phone digit entry can improve recognition perfor- mance. NO TE: When speaking a house number, speak the number “0” as “zero” or “oh”. If the letter “O” is included in the house number, it will not be recognized as “0” even if you speak “oh” instead of “zero”.
4. Select the user whose voice is to be memo- rized by the system and press the ENTER button. 5. Select a category to be learned by the sys- tem from the following list and then press the ENTER button. ● Navigation ● Audio ● Phone ● Vehicle Info.
Speaker Adaptation function settings Edit Name: Edit the user name using the keypad displayed on the screen. Store Result : When this item is turned to ON, the V oice Rec- ognition system can easily recognize the user’s voice that it has learned. Reset Result : Resets the user’s voice that the V oice Recogni- tion system has learned.
T ROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty . If problems are en- countered, follow the solutions given in this guide for the appropriate error. Where the solutions are listed by number, try each solution in turn, starting with number one, until the problem is resolved.
4-138 Monitor, climate, audio, phone and voice recognition systems MEMO.
5 Starting and driving Precautions when starting and driving ................5 - 2 Exhaust gas (carbon monoxide) ..................5 - 2 Three-way catalyst ..............................5 - 2 Tire pressure monitoring system (TPMS) ..........5 - 3 Avoiding collision and rollover .
WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle.
CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously re- duce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat.
Additional information: ● The TPMS does not monitor the tire pressure of the spare tire. ● The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h) . Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving) .
● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.
OFF-ROAD RECOVERY While driving, the right side or left side wheels may unintentionally leave the road surface. If this occurs, maintain control of the vehicle by follow- ing the procedure below . Please note that this procedure is only a general guide.
DRINKING ALCOHOL/DRUGS AND DRIVING WARNING Never drive under the influence of alcohol or drugs. Alcohol in the bloodstream re- duces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others.
The ignition lock is designed so that the ignition switch position cannot be switched to OFF until the shift selector lever is moved to the P (Park) position. When the ignition switch cannot be pushed to- ward the OFF position, proceed as follows: 1. Move the shift selector into the P (Park) position.
CAUTION Do not leave the vehicle with the ignition switch in ACC or ON positions when the engine is not running for an extended pe- riod. This can discharge the battery.
NO TE: The Intelligent Key port does not charge the Intelligent Key battery. If you see the low battery indicator, replace the battery as soon as possible. See “NISSAN Intelligent Key™ battery replacement” in the “Mainte- nance and do-it-yourself” section.
1. Apply the parking brake. 2. Move the shift selector to P (Park) or N (Neutral) . P (Park) is recommended. The starter is designed not to operate if the shift selector is in any of the driving positions. 3. Push the ignition switch to the ON position.
WARNING ● Do not depress the accelerator pedal while shifting from P (Park) or N (Neu- tral) to R (Reverse) , D (Drive) , Ds (Drive Sport) or (M) Manual shift mode. Al- ways depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident.
The CVT can operate in two manual drive modes: ● M (Manual) mode - With the shift selector in the manual shift gate Ds (Drive Sport) mode, M (Manual) mode can be selected by mov- ing the shift selector up (+) or down (–) or using the shift paddles (if so equipped) up (+) or down (–) .
WARNING Apply the parking brake if the shift selec- tor is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage.
on a winding road and feel smooth acceleration or deceleration on a hilly road by moving in a lower gear automatically. When canceling the DS mode, return the shift selector to the D (Drive) position. The transmission returns to the normal driving mode.
● In the manual shift mode, the transmis- sion may shift up automatically to a higher range than selected if the en- gine speed is too high. When the ve- hicle speed decreases, the transmis- sion automatically shifts down and shifts to 1st gear before the vehicle comes to a stop.
Accelerator downshift — in D (Drive) position and manual shift mode For passing or hill climbing, depress the accel- erator pedal to the floor. This shifts the transmis- sion down into lower range, depending on the vehicle speed. High fluid temperature protection mode This transmission has a high fluid temperature protection mode.
T o engage: Firmly depress the parking brake. T o release: 1. Firmly apply the foot brake. 2. Move the shift selector to the P (Park) posi- tion. 3. Firmly depress the parking brake pedal and it will release. 4. Before driving, be sure the brake warning light goes out.
T o set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. T ake your foot off the accelerator pedal. Y our vehicle maintains the set speed. ● T o pass another vehicle, depress the ac- celerator pedal.
● Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelerator position. ● Drive at moderate speeds on the highway . Driving at high speed lowers fuel economy . ● Avoid unnecessary stopping and braking. Maintain a safe distance behind other ve- hicles.
WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. ● Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) .
The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds.
This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer. ANTI-LOCK BRAKING SYSTEM (ABS) WARNING ● The Anti-lock Braking System (ABS) is a sophisticated device, but it cannot pre- vent accidents resulting from careless or dangerous driving techniques.
When the ABS senses that one or more wheels are close to locking up, the actuator rapidly ap- plies and releases hydraulic pressure. This action is similar to pumping the brakes very quickly . Y ou may feel a pulsation in the brake pedal and hear a noise from under the hood or feel a vibration from the actuator when it is operating.
● Do not modify the vehicle’s suspension. If suspension parts such as shock ab- sorbers, struts, springs, stabilizer bars, bushings and wheels are not NISSAN approved for your vehicle or are ex- tremely deteriorated the Vehicle Dy- namic Control system may not operate properly.
DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti- freeze, drain the cooling system, including the engine block. Refill before operating the vehicle. For details, see “Changing engine coolant” in the “Maintenance and do-it-yourself” section of this manual.
ENGINE BLOCK HEATER (if so equipped) WARNING ● Do not use your engine block heater with an ungrounded electrical system or a 2-pronged adapter. Y ou can be se- riously injured by an electrical shock if you use an ungrounded connection. ● Disconnect and properly store the en- gine block heater cord before starting the engine.
5-28 Starting and driving MEMO.
6 In case of emergency Flat tire ...........................................6 - 2 Tire Pressure Monitoring System (TPMS) ..........6 - 2 Changing a flat tire .............................6 - 2 Jump starting . . . ..................................6 - 8 Push starting .
TIRE PRESSURE MONITORING SYSTEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pres- sure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated.
WARNING ● Make sure the parking brake is securely applied and the CVT is shifted into P (Park) . ● Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous. ● Never change tires if oncoming traffic is close to your vehicle.
Open the trunk. Lift the trunk floor carpeting and spare tire cover. Remove the jack 䊊 1 and wheel nut wrench 䊊 2 from the tool box on the right side of the trunk compartment.
Jacking up vehicle and removing the damaged tire WARNING ● Never get under the vehicle while it is supported only by the jack. If it is nec- essary to work under the vehicle, sup- port it with safety stands. ● Use only the jack provided with your vehicle to lift the vehicle.
Always refer to the proper illustrations for the correct placement and jack-up points for your specific vehicle model and jack type. Carefully read the caution label attached to the jack body and the following instruc- tions. 1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench.
4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated ( 䊊 A , 䊊 B , 䊊 C , 䊊 D , 䊊 E ) . Lower the vehicle completely. WARNING ● Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off.
T o start your engine with a booster battery, the instructions and precautions below must be fol- lowed. WARNING ● If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle.
WARNING Always follow the instructions below. Failure to do so could result in damage to the charging system and cause personal injury. 1. If the booster battery is in another vehicle, position the two vehicles to bring their bat- teries near each other.
CAUTION ● CVT models cannot be push-started or tow-started. Attempting to do so may cause transmission damage. ● Do not push start this vehicle. The three-way catalyst may be damaged. If your vehicle is overheating (indicated by an extremely high temperature gauge reading) or if you feel a lack of engine power, detect abnormal noise, etc.
When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could dam- age your vehicle. T owing instructions are avail- able from a NISSAN dealer. Local service opera- tors are generally familiar with the applicable laws and procedures for towing.
CAUTION ● Never tow CVT models with the front wheels on the ground or four wheels on the ground (forward or backward) , as this may cause serious and expensive damage to the transmission. If it is nec- essary to tow the vehicle with the rear wheels raised always use towing dollies under the front wheels.
V EHICLE RECOVERY (freeing a stuck vehicle) Pulling a stuck vehicle Do not use the hook (if so equipped) to tow the vehicle. WARNING ● Stand clear of a stuck vehicle. ● Do not spin your tires at high speed. This could cause them to explode and result in serious injury.
6-14 In case of emergency MEMO.
7 Appearance and care Cleaning exterior ..................................7 - 2 W ashing ......................................7 - 2 W axing ........................................7 - 2 Removing spots ................................7 - 3 Underbody .
In order to maintain the appearance of your ve- hicle, it is important to take proper care of it. T o protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads.
REMOVING SPOTS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store.
CAUTION Follow the directions below to avoid staining or discoloring the wheels: ● Do not use a cleaner that uses strong acid or alkali contents to clean the wheels. ● Do not apply wheel cleaners to the wheels when they are hot. The wheel temperature should be the same as am- bient temperature.
CAUTION ● Never use benzine, thinner or any simi- lar material. ● Small dirt particles can be abrasive and damaging to leather surfaces and should be removed promptly. Do not use saddle soap, car waxes, polishes, oils, cleaning fluids, solvents, deter- gents or ammonia-based cleaners as they may damage the leather’s natural finish.
SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See “Seat belt maintenance” in the “Safety – Seats, seat belts and supplemen- tal restraint system” section of this manual.
CAUTION ● NEVER remove dirt, sand or other de- bris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. ● Never allow water or other liquids to come in contact with electronic compo- nents inside the vehicle as this may damage them.
7-8 Appearance and care MEMO.
8 Maintenance and do-it-yourself Maintenance requirements ..........................8 - 2 General maintenance ..............................8 - 2 Explanation of general maintenance items .........8 - 2 Maintenance precautions . . . ...................
Y our new NISSAN has been designed to have minimum maintenance requirements with long service intervals to save you both time and money . However, some day-to-day and regular maintenance is essential to maintain your NIS- SAN’s good mechanical condition, as well as its emission and engine performance.
When driving in areas using road salt or other corrosive materials, check lubrication frequently . Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely .
Seat belts Check that all parts of the seat belt system (for example, buckles, anchors, adjusters and retractors) operate properly and smoothly, and are installed securely.
When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle.
1. P ower steering fluid reservoir 2. Engine oil filler cap 3. Brake fluid reservoir 4. Air cleaner 5. Fuse block 6. Battery 7. Fuse/Fusible link box 8. Engine oil dipstick 9. Radiator cap 10. Drive belt location 11. Engine coolant reservoir* 12. Windshield washer fluid reservoir* NO TE: Side covers removed for clarity.
The engine cooling system is filled at the factory with Genuine NISSAN Long Life Antifreeze/Coolant to provide year-round anti- freeze and coolant protection. The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary .
CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheat- ing. WARNING ● T o avoid the danger of being scalded, never change the coolant when the en- gine is hot.
CAUTION Oil level should be checked regularly. Op- erating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty. CHANGING ENGINE OIL 1. Park the vehicle on a level surface and apply the parking brake.
CAUTION Be careful not to burn yourself. The engine oil may be hot. 7. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with a wrench. Do not use excessive force. Drain plug tightening torque: 22 - 29 ft-lb (29 - 39 N·m) 8.
CAUTION ● Use only Genuine NISSAN CVT Fluid NS-2-V . Do not mix with other fluids. ● Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2-V will damage the CVT, which is not covered by the NISSAN new vehicle limited warranty. When checking or replacement of CVT Fluid is required, we recommend your NISSAN dealer for servicing.
For further brake fluid specification information, refer to “Capacities and recommended fuel/lubricants” in the “T echnical and consumer information” section of this manual. WARNING ● Use only new fluid from a sealed con- tainer. Old, inferior or contaminated fluid may damage the brake system.
Refill the reservoir more frequently when driving conditions require an increased amount of win- dow washer fluid. Recommended fluid is Genuine NISSAN Wind- shield W asher Concentrate Cleaner & Anti- freeze or equivalent. CAUTION ● Do not substitute engine anti-freeze coolant for window washer solution.
1. Remove the battery caps with a screwdriver as shown. Use a cloth to protect the battery case. 2. Check the fluid level in each cell. If it is necessary to add fluid, add only distilled water to bring the level up to the bottom of the filler opening.
CAUTION ● Do not ground accessories directly to the battery terminal. Doing so will by- pass the variable voltage control sys- tem and the vehicle battery may not charge completely. ● Use electrical accessories with the en- gine running to avoid discharging the vehicle battery.
2. Have the belt checked regularly for condi- tion and tension in accordance with the maintenance schedule found in the “NISSAN Service and Maintenance Guide” .
The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance log shown in the “NISSAN Service and Mainte- nance Guide.” When replacing the filter, wipe the inside of the air cleaner filter housing and the cover with a damp cloth.
CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent.
Be careful not to let anything get into the washer nozzle 䊊 A . This may cause clogging or improper windshield washer operation. If something gets into the nozzle, remove it with a needle or small pin 䊊 B . If the brakes do not operate properly , have the brakes checked by a NISSAN dealer.
T wo types of fuses are used. T ype 䊊 A is used in the fuse boxes in the engine compartment. T ype 䊊 B is used in the passenger compartment fuse box. T ype A fuses are provided as spare fuses. They are stored in the passenger compartment fuse box.
3. Remove the fuse box cover by pushing the tab and lifting the cover up. 4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment. 5. If the fuse is open 䊊 A , replace it with a new fuse 䊊 B .
PASSENGER COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire. If any electrical equipment does not operate, check for an open fuse. 1.
4. If the fuse is open 䊊 A , replace it with an equivalent good fuse 䊊 B . 5. Push the fuse box cover to install. 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer. CAUTION Be careful not to allow children to swallow the battery or removed parts.
NISSAN INTELLIGENT K EY™ Replace the battery in the Intelligent K ey as fol- lows: 1. Remove the mechanical key from the Intelli- gent K ey. 2. Insert a small screwdriver 䊊 A into the slit 䊊 B of the corner and twist it to separate the upper part from the lower part.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.
EXTERIOR AND INTERIOR LIGHTS Item Wattage (W) Bulb No.* Headlight assembly High (Halogen) 60 9005/HB3 Low (Halogen) (if so equipped) 55 H11 Low (Xenon) (if so equipped) 35 D2S Park/T urn 27/8 3457NAK Side marker 55 WY5W Front fog light 55 H11 Front personal/map lights 8 — Glove box light 3.
1. Headlight assembly 2. Map light 3. Rear personal lights 4. Fog light 5. Step light 6. High-mounted stop light (T ype A) 7. T runk light 8. High-mounted stop light (T ype B) 9.
Replacement procedures All other lights are either type A , B, C or D. When replacing a bulb, first remove the lens, lamp and/or cover. Indicates bulb removal Indicates bulb installation Use a cloth 䊊 1 to protect the housing. Use a cloth 䊊 1 to protect the housing.
Use a cloth 䊊 1 to protect the housing. Use a cloth 䊊 1 to protect the housing. Step light LDI0341 Rear personal light WDI0670 T runk light WDI0343 Maintenance and do-it-yourself 8-29 墌 REVIEW C.
If you have a flat tire, see the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pressure of all tires except the spare.
WARNING ● Improperly inflated tires can fail suddenly and cause an accident. ● The Gross V ehicle Weight Rating (GVWR) is located on the F .M .V .S.S./C .M .V .S.S. certifica- tion label. The vehicle weight ca- pacity is indicated on the Tire and Loading Information label (if so equipped) .
Tire and loading information label 䊊 1 Seating capacity: The maximum num- ber of occupants that can be seated in the vehicle. 䊊 2 V ehicle load limit: See loading infor- mation in the “T echnical and con- sumer information” section. 䊊 3 Original tire size: The size of the tires originally installed on the vehicle at the factory .
Checking tire pressure 1. Remove the valve stem cap from the tire. 2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem side- ways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage.
Size Cold Tire Inflation Pres- sure Front Original Tire P245/45VR18 230 kPa, 33 PSI P245/40/VR19 230 kPa, 33 PSI Rear Original Tire P245/45VR18 230 kPa, 33 PSI P245/40/VR19 230 kPa, 33 PSI Spare Tire .
䊊 1 Tire size (example: P215/65R15 95H) 1. P: The “P” indicates the tire is de- signed for passenger vehicles (not all tires have this information) . 2. Three-digit number (215): This num- ber gives the width in millimeters of the tire from sidewall edge to side- wall edge.
䊊 2 TIN (Tire Identification Number) for a new tire (example: DO T XX XX XXX XXXX) 1. DO T : Abbreviation for the “Depart- ment Of T ransportation” . The symbol can be placed above, below or to the left or right of the Tire Identification Number.
䊊 7 The word “radial” The word “radial” is shown if the tire has radial structure. 䊊 8 Manufacturer or brand name Manufacturer or brand name is shown.
studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS CAUTION Tire chains/cables should not be installed on P245/40VR19 size tires. Installation of the tire chains/cables on P245/40VR19 size tires will cause damage to the ve- hicle.
Wheel nut tightening torque: 83 ft-lb (113 N·m) The wheel nuts must be kept tight- ened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval. WARNING ● After rotating the tires, check and adjust the tire pressure.
Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in “Wheels and tires” in the “T echnical and consumer information” section of this manual.
Care of wheels ● W ash the wheels when washing the vehicle to maintain their appearance. ● Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed. ● Do not use abrasive cleaners when washing the wheels.
8-42 Maintenance and do-it-yourself MEMO.
9 T echnical and consumer information Capacities and recommended fuel/lubricants .........9 - 2 Fuel recommendation . . . ........................9 - 3 Engine oil and oil filter recommendations ..........9 - 5 Air conditioner system refrigerant and oil recommendations .
The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity. Capacity (Approximate) Recommended Fluids and Lubricants US measure Imp measure Liter Fuel 20 gal 16-5/8 gal 75.
FUEL RECOMMENDATION Use unleaded premium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) num- ber (Research octane number 96) . If unleaded premium gasoline is not available unlea.
If any driveability problems such as engine stall- ing and difficult hot-starting are experienced after using oxygenate-blend fuels, immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. T ake care not to spill gasoline during refu- eling.
ENGINE OIL AND OIL FILTER RECOMMENDATIONS Selecting the correct oil It is essential to choose the correct grade, quality and viscosity engine oil to ensure satisfactory engine life and performance. See “Capacities and recommended fuel/lubricants” earlier in this section.
Y our engine was filled with a high-quality engine oil when it was built. Y ou do not have to change the oil before the first recommended change interval.
ENGINE Model VQ35DE T ype Gasoline, 4-cycle, DOHC Cylinder arrangement 6-cylinder, V-block, Slanted at 60° Bore x Stroke in (mm) 3.760 x 3.205 (95.5 x 81.4) Displacement cu in (cm 3 ) 213.45 (3,498) Firing order 1–2–3–4–5–6 Idle speed No adjustment is necessary .
WHEELS AND TIRES Wheels 18 x 8.0JJ 19 x 8.0JJ Tires P245/45VR18 P245/40VR19 Spare tire T145/80D17 Speed rating 18” V 19” V DIMENSIONS AND WEIGHTS Overall length in (mm) 190.6(4,843) Overall width in (mm) 73.2(1,860) Overall height in (mm) 57.8(1,467) Front T rack 18 inch tire in (mm) 62.
When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline.
ENGINE SERIAL NUMBER The number is stamped on the engine as shown. F .M.V .S.S./C.M.V .S.S. CERTIFICATION LABEL The Federal/Canadian Motor V ehicle Safety Standard (F .
TIRE AND LOADING INFORMATION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed to the underside of the hood as shown.
Use the following steps to mount the front license plate: 䊊 1 Make holes on the plastic finisher at the location mark (small dimple) using a 0.31 in (8 mm) drill. Apply light pressure to the drill. Install the license plate holder using the two screws provided with the holder.
● Vehicle Capacity Weight, Load limit, T otal load capacity - maximum total weight limit specified of the load (passengers and cargo) for the ve- hicle.
Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle.
WARNING Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and perfor- mance and may lead to accidents. CAUTION ● Do not tow a trailer or haul a heavy load for the first 500 miles (800 km) . Y our engine, axle or other parts could be damaged.
T emperature conditions also can affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating.
Maximum Gross V ehicle W eight (GVW)/Maximum Gross Axle W eight (GA W) The GVW of the towing vehicle must not exceed the Gross Vehicle W eight Rating (GVWR) shown on the F .
4,546 lb. (2062 kg) GVWR – 4,446 lb. (2016 kg) GVW = 100 lb. (45 kg) Available for tongue weight 1,000 lb. (454 kg) Capacity available for towing 100 lb.
● The threaded shank of the hitch ball must be long enough to be properly secured to the ball mount. There should be at least 2 threads showing beyond the lock washer and nut. Ball mount The hitch ball is attached to the ball mount and the ball mount is inserted into the hitch receiver.
T railer lights CAUTION When splicing into the vehicle electrical system, a commercially available power- type module/converter must be used to provide power for all trailer lighting.
● Check your hitch, trailer tire pressure, ve- hicle tire pressure, trailer light operation, and trailer wheel lug nuts every time you attach a trailer to the vehicle. ● Be certain your rearview mirrors conform to all federal, state or local regulations.
● Avoid towing a trailer for your vehicle’s first 500 miles (805 km) . ● For the first 500 miles (805 km) that you do tow , do not drive over 50 MPH (80 km/h) . ● Have your vehicle serviced more often than at intervals specified in the recommended Maintenance Schedule in the “NISSAN Ser- vice and Maintenance Guide” .
CAUTION ● Failure to follow these guidelines can result in severe transmission damage. ● Whenever flat towing your vehicle, al- ways tow forward, never backward. ● DO NO T tow any automatic transmis- sion vehicle with all four wheels on the ground (flat towing) .
WARNING The temperature grade for this tire is es- tablished for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, ei- ther separately or in combination, can cause heat build-up and possible tire failure.
Due to legal requirements in some states and Canadian Provinces, your vehicle may be re- quired to be in what is called the “ready condi- tion” for an Inspection/Maintenance (I/M) test of the emission control system. The vehicle is set to the “ready condition” when it is driven through certain driving patterns.
This vehicle is equipped with an Event Data Re- corder (EDR) . The main purpose of an EDR is to record, in certain crash or near crash-like situa- tions, such as an air bag deployment or hitting a road obstacle, data that will assist in understand- ing how a vehicle’s systems performed.
For Canada T o purchase a copy of a genuine NISSAN Ser- vice Manual or Owner’s Manual please contact your nearest NISSAN dealer. For the phone num- ber and location of a NISSAN dealer in your area call the NISSAN Information Center at 1-800- 387-0122 and a bilingual NISSAN representa- tive will assist you.
10 Index A Active Head Restraint .............. 1 - 8 Air bag (See supplemental restraint s y s t e m ) ..................... 1 - 3 5 Air bag system Front (See supplemental front impact air bag system) ............... 1 - 4 2 A i r b a g w a r n i n g l i g h t .
C Capacities and recommended fuel/lubricants ................... 9 - 2 Car phone or CB radio ............. 4 - 8 7 C a r g o n e t .................... 2 - 4 0 Cargo (See vehicle loading information) . . .9-12 C D c a r e a n d c l e a n i n g .......
F Flashers (See hazard warning flasher switch) ...... 2 - 3 2 Flat tire ...................... 6 - 2 Floor mat positioning aid ............. 7 - 5 Fluid Brake fluid .................. 8 - 1 2 Capacities and recommended f u e l / l u b r i c a n t s ..
K Keyfob battery replacement .......... 8 - 2 3 Keyless entry With Intelligent Key system (See Intelligent Key system) ........ 3 - 1 3 Keys, For Intelligent K ey system ......... 3 - 2 L Labels Air conditioner specification label ..... 9 - 1 1 C.M.V .
Outside mirror control ............. 3 - 2 7 Outside mirrors ................. 3 - 2 7 Overheat I f y o u r v e h i c l e o v e r h e a t s.......... 6 - 1 0 Owner’s manual order form .......... 9 - 2 7 Owner’s manual/service manual order information .
S R S w a r n i n g l a b e l ............... 1 - 4 9 Starting Before starting the engine ......... 5 - 1 0 Jump starting ................. 6 - 8 Precautions when starting and driving . . .5-2 Push starting ................ 6 - 1 0 Starting the engine .
V ehicle security system ............. 2 - 2 3 V ehicle security system (NISSAN vehicle immobilizer system) , e n g i n e s t a r t ............. 2 - 2 4 , 3 - 3 , 5 - 1 0 V entilators .................... 4 - 3 4 V i s o r s ...................... 3 - 2 4 V oice recognition system .
Een belangrijk punt na aankoop van elk apparaat Nissan Maxima (2009) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Nissan Maxima (2009) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Nissan Maxima (2009) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Nissan Maxima (2009) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Nissan Maxima (2009) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Nissan Maxima (2009) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Nissan Maxima (2009) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Nissan Maxima (2009) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
