Gebruiksaanwijzing /service van het product Murano (2014) van de fabrikant Nissan
Ga naar pagina of 508
® 2014 M U RAN O OWN E R’S MAN UAL For y our safety , read car efully and keep in this v ehicle. 2014 N I S SAN M U RAN O Z5 1-W Z5 1-W Printing : November 2012 (31) Publication No.
Welcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. This manual was prepared to help you under- stand the operation and maintenance of your vehicle so that you may enjoy many miles of driving pleasure.
.
MODIFICA TION OF Y OUR VEHI- CLE This vehicle should not be modified. Modification could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems result- ing from modification may not be covered under NISSAN warranties.
above call attention to an item in the illustration. CALIFORNIA PROPOSIT ION 65 W ARNING WARNING Engine exhaust, some of its constitu- ents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
NISSAN CARES ... Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Y our satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Y our NISSAN dealer is always available to assist you with all your automobile sales and service needs.
.
Illustrated table of contents 0 Safety — Seats, seat belts and supplemental restraint system 1 Instruments and controls Pre-driving checks and adjustments Monitor, heater, air conditioner, audio, ph.
.
0 Illustrated table of contents Seats, seat belts and Supplemental Restraint System (SRS) ............................................................................ 0-2 Hardtop models .................................................................
0-2 Illustrated table of contents JVO0063X HARDT OP MODELS 1. Rear center seat belt (P .1-23) 2. Head restraints (P .1-11) — Front-seat Active Head Restraints (P .1-14) 3. Seat belts (P .1-15) 4. Armrest (P .1-15) 5. Roof-mounted curtain side-impact and rollover supplemental air bags (P .
SSI0834 CROSSCABRIOLET MODELS 1. Dual pop-up roll bar system (P .1-62) 2. Seat belts (P .1-15) 3. Head restraints (P .1-11) — Front-seat Active Head Restraints (P .1-14) 4. Door-mounted curtain side-impact and rollover supplemental air bags (P .1-46) 5.
0-4 Illustrated table of contents JVO0040X HARDT OP MODELS 1. Hood (P .3-20) 2. Headlight and turn signal lights — Switch operation (P .2-37) — Bulb replacement (P .8-27) 3. Windshield wiper and washer — Switch operation (P .2-32) — Rain-sensing auto wiper system* (P .
SSI0835 CROSSCABRIOLET MODELS 1. Hood (P .3-20) 2. Headlight and turn signal lights — Switch operation (P .2-37) — Bulb replacement (P .8-27) 3. Windshield wiper and washer — Switch operation (P .2-32) — Blade replacement (P .8-18) — Window washer fluid (P .
0-6 Illustrated table of contents SSI0813 HARDT OP MODELS 1. Lift gate (P .3-20) — Remote keyless entry system (P .3-16) — Intelligent Key system (P .3-8) 2. Rear window wiper and washer — Switch operation (P .2-35) — Window washer fluid (P .8-13) 3.
SSI0836 CROSSCABRIOLET MODELS 1. Antenna (P .4-87) — Satellite radio antenna (P .4-47) 2. High-mounted stop light (P .8-29) 3. Rear window defroster (P .2-36) 4. T runk (P .3-25) — Remote keyless entry system (P .3-16) — Intelligent Key system (P .
0-8 Illustrated table of contents SSI0815 HARDT OP MODELS 1. Cargo cover* (P .2-52) 2. Rear personal light (P .2-60) 3. Coat hooks (P .2-55) 4. Automatic drive positioner switch* (P .3-51) 5. Door armrest — Power window switch (P .2-55) — Power door lock switch (P .
SSI0837 CROSSCABRIOLET MODELS 1. Door armrest — Power window switch (P .2-55) — Power door lock switch (P .3-7) — Outside mirror remote control switch (P .3-49) 2. Automatic drive positioner switch (P .3-51) 3. Sun visors (P .3-47) 4. Front map lights (P .
0-10 Illustrated table of contents JVO0067X 1. Heated steering wheel switch* (P .2-41) 2. Power lift gate switch* (Hardtop models) (P .3-20) or trunk lid release switch (Cross- Cabriolet models) (P .3-25) 3. Warning systems switch* (P .2-43) — Lane Departure Warning (LDW) system* (P .
— Heated seat switches* (P .2-42) — All-Wheel Drive (AWD) LOCK switch* (Hardtop models) (P .5-33) — Soft top operating switch (CrossCabriolet models) (P .
0-12 Illustrated table of contents SSI0839 1. Side ventilator (P .4-40) 2. Meters and gauges (P .2-5) 3. Push-button ignition switch (P .5-11) 4. Center ventilator (P .4-40) 5. Center display — Center color display* (P .4-3) — Navigation system** 6.
JVO0043X 1. Instrument brightness control switch (P.2-40) 2. T achometer (P .2-7) 3. Speedometer (P .2-6) 4. Fuel gauge (P .2-8) 5. Warning/indicator lights (P .2-11) 6. T rip computer switch (P .2-25) 7. Dot matrix liquid crystal display (P .2-20) — Trip computer (P .
0-14 Illustrated table of contents SDI2172 VQ35DE ENGINE 1. Power steering fluid reservoir (P .8-11) 2. Drive belt location (P .8-15) 3. Engine oil filler cap (P .8-8) 4. Brake fluid reservoir (P .8-12) 5. Air cleaner (P .8-17) 6. Fuse/fusible link holder (P .
Warning light Name Page All-Wheel Drive (AWD) warning light (AWD models)* 2-12 Anti-lock Braking System (ABS) warning light 2-12 Blind Spot Warning (BSW) light (orange)* 2-13 Brake warning light 2-13 .
0-16 Illustrated table of contents MEMO.
1 Safety — Seats, seat belts and supplemental restraint system Seats ............................................................................................ 1-2 Front seats .......................................................................
1-2 Safety — Seats, seat belts and supplemental restraint system SSS0133 WARNING . Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries.
SSS0792 FRONT SEA TS Manual seat adjustment Forward and backward: Pull the lever * 1 up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. Reclining: T o recline the seatback, pull the lever * 2 up and lean back.
1-4 Safety — Seats, seat belts and supplemental restraint system SSS0793 Seat lifter (if so equipped) : Pull up or push down the adjusting lever to adjust the seat height until the desired position is achieved. SSS0684 Lumbar support (if so equipped) : The lumbar support feature provides lower back support to the driver.
JVR0038X Forward and backward: Moving the switch * A forward or backward will slide the seat forward or backward to the desired position. Pushing the front * 1 or back * 2 end of the slide switch * B will slide the driver seat forward or backward to the desired position (Cross- Cabriolet models driver’s seat only) .
1-6 Safety — Seats, seat belts and supplemental restraint system JVR0039X Reclining: Move the recline switch * A backward until the desired angle is obtained. T o bring the seatback forward again, move the switch * A forward. Push and hold the back * 2 end of the reclining switch * B until the desired angle is obtained.
SSS1028 Lumbar support (if so equipped) : The lumbar support feature provides lower back support to the driver. Push the front * 1 or back * 2 end of the switch to adjust the seatback lumbar area. SSS1172 Front passenger’s seatback switch SSS1175 Remote walk-in switch Walk -in function (front passenger seat, CrossCabriolet models) : CAUTION .
1-8 Safety — Seats, seat belts and supplemental restraint system Alternatively, you can push the remote walk- in switch located on the instrument panel to fold down the front passenger’s seatback and unlock the seat position. 2. Slide the seat forward to the foremost position manually.
SSS0569 REAR SEA TS (Hardtop models) Folding Before folding the rear seats: . Secure the seat belts on the seat belt hooks on the side wall. (See “Seat belt hooks (Hardtop models)” later in this section.) . Disconnect and stow the center seat belt and tongue into the retractor base.
1-10 Safety — Seats, seat belts and supplemental restraint system beep sounds for 4 seconds and the seatback will return to the folded position automatically. Check if there are any obstacles caught that prevent seats from returning to the folded position.
SSS0227A Reclining Pull the reclining strap * A and position the seatback at the desired angle. Release the reclining strap after positioning the seat at the desired angle. The reclining feature allows adjustment of the seatback for occupants of different sizes to help obtain proper seat belt fit.
1-12 Safety — Seats, seat belts and supplemental restraint system JVR0140X The illustration shows the seating positions equipped with head restraints and headrest.
SSS0993 T o raise the head restraint, pull it up. SSS0994 T o lower, push and hold the lock knob and push the head restraint down. SSS0995 Removal Use the following procedure to remove the adjustable head restraints. 1. Pull the head restraint up to the highest position.
1-14 Safety — Seats, seat belts and supplemental restraint system SSS0996 Install 1. Align the head restraint stalks with the holes in the seat. Make sure that the head restraint is facing the correct direction. The stalk with the adjustment notches * 1 must be in- stalled in the hole with the lock knob * 2 .
SSS0229A ARMREST (Hardtop models) Rear armrest Pull the armrest forward until it is horizontal. PRECAUTIONS ON SEA T BEL T USAGE If you are wearing your seat belt properly adjusted, and you are sittin.
1-16 Safety — Seats, seat belts and supplemental restraint system SSS0136 SSS0134 SSS0016 SSS0014.
WARNING . Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be prop- erly restrained in the rear seat and, if appropriate, in a child restraint. . The seat belt should be properly adjusted to a snug fit.
1-18 Safety — Seats, seat belts and supplemental restraint system damaged. PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug, and always position the lap belt as low as possible around the hips, not the waist.
* 1 may also be released. Release the connector tongue by inserting a suita- ble tool (such as a key) into the connector buckle * A . If the seat belt cannot be unbuckled or is already unbuckled, release the child by cutting the seat belt with a suitable tool (such as a knife or scissors) to release the seat belt.
1-20 Safety — Seats, seat belts and supplemental restraint system SSS0290 3. Position the lap belt portion low and snug on the hips as shown. 4. Pull the shoulder belt portion toward the retractor to take up extra slack. Be sure the shoulder belt is routed over your shoulder and across your chest.
restrict further belt movement. If the retractor does not lock during this check or if you have any question about seat belt operation, see a NISSAN dealer. SSS1181 Seat belt guide (front seats, CrossCab- riolet models) When the seat belt guide is used with the front seat, the seat belt can easily be pulled out.
1-22 Safety — Seats, seat belts and supplemental restraint system SSS0351A Shoulder belt height adjustmen t (Hard- top models) The shoulder belt anchor height should be adjusted to the position best for you. (See “Precautions on seat belt usage” earlier in this section.
SSS0846 Rear center seat belt (Hardtop models) The rear center seat belt has a connector tongue * 1 and a seat belt tongue * 2 . Both the connector tongue and the seat belt tongue must be securely latched for proper seat belt opera- tion. SSS0241 WARNING .
1-24 Safety — Seats, seat belts and supplemental restraint system SSS0225 Stowing rear center seat belt : When folding down the rear seat, the rear center seat belt can be retracted into a stowed position as follows: 1.
SSS0232 Attaching rear center seat belt : Always be sure the rear center seat belt connector tongue and connector buckle are attached. Disconnect only when folding down the rear seat. T o connect the buckle: 1. Pull out the connector tongue from the retractor base * 1 .
1-26 Safety — Seats, seat belts and supplemental restraint system SSS0235 Storing rear seat belt buckles (Hardtop models) Before folding down the seat, put the buckles in the storage of the seat cushion to avoid dropping it under the seat cushion.
JVR0183X WARNING Do not allow children to play with the seat belts. Most seating positions are equipped with Automatic Locking Re- tractor (ALR) mode seat belts. If the seat belt becomes wrapped around a child’s neck with the ALR mode acti- vated, the child can be seriously injured or killed if the seat belt retracts and becomes tight.
1-28 Safety — Seats, seat belts and supplemental restraint system properly restrained in the rear seat than in the front seat. This is especially important because your vehicle has a supplemental restraint sys- tem (Air bag system) for the front passen- ger.
SSS0099 SSS0100 PRECAUTIONS ON CHILD RE- STRAINTS WARNING . CrossCabriolet models are not equipped with top tethers. A child restraint system requiring a top tether strap cannot be properly in- stalled and should not be used in your vehicle.
1-30 Safety — Seats, seat belts and supplemental restraint system properly fitted. — Never use the anchor points for adult seat belts or harnesses. — A child restraint with a top tether strap should not be used in the front passenger seat. — Keep seatbacks as upright as possible after fitting the child restraint.
SSS0419B LA TCH label location (Hardtop models) SSS0933 LA TCH label location (CrossCabriol et models) LA TCH Lower Anchors SY STEM Y our vehicle is equipped with special anchor points that are used with the LA T CH (Lower Anchors and T ethers for CHildren) system compatible child restraints.
1-32 Safety — Seats, seat belts and supplemental restraint system SSS0637 LA TCH lower anchor location LA TCH lower anchor location The LA TCH anchors are located at the rear of the seat cushion near the seatback. A label is attached to the seatback to help you locate the LA T CH anchors.
SSS0822 T op tether anchor (Hardtop models) WARNING . If the cargo cover (if so equipped) contacts the top tether strap when it is attached to the top tether anchor, remove the cargo cover from the vehicle or secure it on the cargo floor below its attachment location.
1-34 Safety — Seats, seat belts and supplemental restraint system SSS0639 Rear-facing — step 3 2. Secure the child restraint anchor attach- ments to the LA T CH lower anchors. Check to make sure the LA T CH attachment is properly attached to the lower anchors.
section. (Hardtop models) SSS0100 Rear-facing — step 1 Refer to all Warnings and Cautions in the “Child safety” earlier in this section and “Child re- straints” earlier in this section before installing a child restraint. Follow these steps to install a rear-facing child restraint using the vehicle seat belts in the rear seats: 1.
1-36 Safety — Seats, seat belts and supplemental restraint system SSS0655 Rear-facing — step 3 3. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode) .
SSS0658 Rear-facing — step 6 6. After attaching the child restraint, test it before you place the child in it. Push it from side to side while holding the child restraint near the seat belt path. The child restraint should not move more than 1 inch (25 mm) , from side to side.
1-38 Safety — Seats, seat belts and supplemental restraint system SSS0646 Forward-facing rigid-mounted — step 2 3. The back of the child restraint should be secured against the vehicle seatback. If necessary, adjust or remove the head restraint to obtain the correct child restraint fit.
child restraint is loose, repeat steps 1 through 6. FORW ARD-FACING CHILD RE- STRAINT INST ALLA TION USING THE SEA T BEL TS WARNING . The three-point seat belt with Auto- matic Locking Retractor (ALR) must be used when installing a child restraint. Failure to use the ALR mode will result in the child re- straint not being properly secured.
1-40 Safety — Seats, seat belts and supplemental restraint system SSS0360B Forward-facing — step 3 3. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing.
SSS0653 Forward-facing — step 6 6. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt.
1-42 Safety — Seats, seat belts and supplemental restraint system SSS0823 Forward-facing — step 10 10. If the child restraint is installed in the front passenger seat, place the ignition switch in the ON position. The front passenger air bag status light should illuminate.
. A booster seat must only be in- stalled in a seating position that has a lap/shoulder belt. LRS0455 Booster seats of various sizes are offered by several manufacturers.
1-44 Safety — Seats, seat belts and supplemental restraint system LRS0464 All U.S. states and Canadian provinces or territories require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated.
LRS0454 Front passenger position 3. The booster seat should be positioned on the vehicle seat so that it is stable. If necessary, adjust or remove the head restraint or headrest to obtain the correct booster seat fit. If the head restraint or headrest is removed, store it in a secure place.
1-46 Safety — Seats, seat belts and supplemental restraint system PRECAUTIONS ON SUPPLEMENT AL RESTRAINT SY STEM This Supplemental Restraint System (SRS) section contains important information concern- ing the following systems: . Driver and passenger supplemental front- impact air bag (NISSAN Advanced Air Bag System) .
SSS0131 SSS0132 WARNING . The front air bags ordinarily will not inflate in the event of a side impact, rear impact, rollover, or lower se- verity frontal collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.
1-48 Safety — Seats, seat belts and supplemental restraint system back against the seatback and as far-away as practical from the steer- ing wheel or instrument panel. Al- ways use the seat belts. . The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened.
SSS0008 SSS0009 SSS0099 SSS0100 WARNING . Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding posi- tions are shown in the illustrations.
1-50 Safety — Seats, seat belts and supplemental restraint system SSS0059A Do not lean against doors or windows. SSS0188A SSS0140 SSS0162 SSS0159 WARNING Front seat-mounted side-impact sup- plementa.
reduce the risk or severity of injury in various kinds of accidents. . The seat belts and air bags are most effective when you are sitting well back and upright in the seat with both feet on the floor.
1-52 Safety — Seats, seat belts and supplemental restraint system SSS0847 Hardtop models NISSAN ADVANCED AIR BAG SY STEM (front seats) 1. Crash zone sensor 2. Supplemental front-impact air bag modules 3. Front seat-mounted side-impact supplemental air bag modules 4.
SSS1174 CrossCabriolet models 1. Crash zone sensor 2. Supplemental front-impact air bag modules 3. Front seat-mounted side-impact supplemental air bags 4. Occupant classification system control unit 5. Occupant classification sensor (pattern sensor) 6.
1-54 Safety — Seats, seat belts and supplemental restraint system front air bag may inflate in a crash, depending on the crash severity and whether the front occupants are belted or unbelted.
an accident. Status light: The front passenger air bag status light is located on the instrument panel below the air conditioner controls. After the ignition switch is placed in the ON position, the f.
1-56 Safety — Seats, seat belts and supplemental restraint system occupants are seated and restrained properly. Using the passenger air bag status light, you can monitor when the front passenger air bag is automatically turned OFF with the seat occu- pied.
. Do not make unauthorized changes to your vehicle’s electrical system, suspension system or front end structure. This could affect proper operation of the front air bag sys- tem. . T ampering with the supplemental air bag system may result in serious personal injury.
1-58 Safety — Seats, seat belts and supplemental restraint system SSS0848 Hardtop models SSS0982 CrossCabriolet moldels FRONT SEA T -MOUNTED SIDE-IM- P ACT SUPPLEMEN T AL AIR BAG AND ROOF-MOUNTED CU.
air bags inflate quickly in order to help protect the occupants. Because of this, the force of the side air bags and curtain and rollover air bags inflating can increase the risk of injury if the occupant is too close to, or is against, these air bag modules during inflation.
1-60 Safety — Seats, seat belts and supplemental restraint system placed together with the retractor and buckle as a unit. . If the vehicle becomes involved in a collision but a pretensioner is not activated, be sure to have the pre- tensioner system checked and, if necessary, replaced by a NISSAN dealer.
SSS1016 SUPPLEMENT AL AIR BAG W ARNING LABELS Warning labels about the supplemental front- impact air bag system are placed in the vehicle as shown in the illustration.
1-62 Safety — Seats, seat belts and supplemental restraint system ment of these systems should be done only by a NISSAN dealer. When maintenance work is required on the vehicle, the front air bags, side air bags, curtain and rollover air bags and pretensioners and related parts should be pointed out to the person performing the maintenance.
WARNING Failure to follow the warnings and instructions in this section may result in serious injury or death. . The dual pop-up roll bars deploy upward at a high speed when acti- vated. Keep hands and other body parts away from the dual pop-up roll bars.
1-64 Safety — Seats, seat belts and supplemental restraint system MEMO.
2 Instruments and controls Cockpit ........................................................................................ 2-3 Instrument panel ........................................................................ 2-4 Meters and gauges ...........
Cargo cover (if so equipped for Hardtop models) .............................................................. 2-52 Luggage hooks (Hardtop models) ............................... 2-53 Luggage cover (CrossCabriolet models) ................... 2-53 Roof rack (if so equipped for Hardtop models) .
JVO0067X 1. Heated steering wheel switch* 2. Power lift gate switch* (Hardtop models) or trunk lid release switch (CrossCabriolet models) 3. Warning systems switch* - Lane Departure Warning (LDW) system* - Blind Spot Warning (BSW) system* 4. Instrument brightness control switch 5.
2-4 Instruments and controls SSI0839 1. Side ventilator 2. Meters and gauges 3. Push-button ignition switch 4. Center ventilator 5. Center display — Center color display* — Navigation system** 6.
JVO0043X 1. Instrument brightness control switch 2. T achometer 3. Speedometer 4. Fuel gauge 5. Warning/indicator lights 6. T rip computer switch 7. Dot matrix liquid crystal display — Trip computer 8. Engine coolant temperature gauge 9. Odometer/twin trip odometer/Continuously V ari- able Transmission (CVT) position indicator 10.
2-6 Instruments and controls JVI0252X Speedometer SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h) .
JVI0253X T ACHOMETER The tachometer indicates engine speed in revolutions per minute (RPM) . Do not rev the engine into the red zone * 1 . CAUTION When engine speed approaches the red zone, shift to a higher gear or reduce engine speed. Operating the engine in the red zone may cause serious engine damage.
2-8 Instruments and controls JVI0338X FUEL GAUGE The gauge indicates the approximate fuel level in the tank. The gauge may move slightly during braking, turning, acceleration, or going up or down hills. The gauge needle returns to E (Empty) after the ignition switch is pushed to the OFF position.
on your everyday route. The compass will be calibrated once it has tracked 3 complete circles. T o turn on and off the compass manually , push the switch * A while the ignition switch is in the ON position.
2-10 Instruments and controls Z ONE VARIA TION CHANGE PROCE- DURE The difference between magnetic north and geographical north is known as variance. In some areas, this difference can sometimes be great enough to cause false compass readings. Follow these instructions to set the variance for your particular location if this happens: 1.
All-Wheel Drive (AWD) warning light (A WD models)* Low tire pressure warning light Exterior light indicator Anti-lock Braking System (ABS) warning light Master warning light Front passenger air bag st.
2-12 Instruments and controls CHECKING BULBS With all doors closed, apply the parking brake and push the ignition switch to the ON position without starting the engine.
tance. (See “Brake system” in the “5. Starting and driving” section.) Blind Spot W arning (BSW) light (orange; if so equipped) When the ignition switch is placed in the "ON" position, the light will first illuminate in orange and turn green.
2-14 Instruments and controls Engine oil pressure warning light This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop.
position as long as the low tire pressure warning light remains illuminated. For additional information, see “Dot matrix liquid crystal display” later in this section, “Tire Pressure Monitoring System (TPMS)” in the “5. Starting and driving” section and “Tire Pressure Monitoring System (TPMS)” in the “6.
2-16 Instruments and controls Master warning light When the ignition switch is in the ON position, the master warning light illuminates if any of the following are displayed on the dot matrix liquid crystal display: . No key warning . Low fuel warning .
is still driveable. For additional information, see “V ehicle Dynamic Control (VDC) system” in the “5. Starting and driving” section of this manual. INDICA T OR LIGHTS All-Wheel Drive (AWD) L OCK indicator light (A WD models) This light illuminates when the ignition switch is placed in the ON position, and turns off within 1 second.
2-18 Instruments and controls Lane Departure Warning (LDW) light (green; if so equipped) The Lane Departure W arning (LDW) light (green) will illuminate when the LDW system is turned on. The light turns off when the system is turned off. (See “Blind Spot W arning (BSW)/ Lane Departure Warning (LDW) systems” in the “5.
Overdrive off indicator light The overdrive off indicator light illuminates when the overdrive off mode is selected. For additional information, see “Continuously V ariable T ransmission (CVT)” in the “5. Starting and driving” section of this manual.
2-20 Instruments and controls AUDIBLE REMINDERS Key reminder chime A chime will sound if the driver side door is opened while the ignition switch is pushed to the ACC position or pushed to the OFF or L OCK position with the Intelligent Key left in the Intelligent Key port.
JVI0540X OPERA TIONAL INDICA T ORS 1. Engine start operation indicator This indicator appears when the shift lever is in the P (Park) position. This indicator means that the engine will start by pushing the ignition switch with the brake pedal depressed.
2-22 Instruments and controls button ignition switch” in the “5. Starting and driving” section.) 3. Key removal indicator This indicator appears when the driver’s door is opened with the ignition switch in the OFF or L OCK position and the key placed in the key port.
the empty (E) position. 11. Low washer fluid warning This warning appears when the washer tank fluid is at a low level. Add washer fluid as necessary. (See “Window washer fluid” in the “8.
2-24 Instruments and controls SIC4237 MAINTENANCE INDICA T ORS 1. Engine oil replacement indicator This indicator appears when the customer set time comes for changing the engine oil. Y ou can set or reset the distance for changing the engine oil. (See “T rip computer” later in this section.
SIC3580 TRIP COMPUTER Switches for the trip computer are located on the right side of the combination meter panel. T o operate the trip computer, push the side or front of the switches as shown above. * A switch * B switch When the ignition switch is pushed to the ON position, modes of the trip computer can be selected by pushing the switch * A .
2-26 Instruments and controls SIC3674 Average fuel consumption (MPG, l/100 km) and speed (MPH or km/h) Fuel consumption: The average fuel consumption mode shows the average fuel consumption since the last reset. Resetting is done by pushing the switch * B for longer than 1 second.
SIC4702 Distance to empty (dte — miles or km) The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly being calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption.
2-28 Instruments and controls SIC3678 Setting Setting cannot be made while driving. A message “Setting can only be operated when stopped” is also displayed on the dot matrix crystal display. The switch * A and switch * B are used in the setting mode to select and decide a menu.
SIC3993 W arning check T o see if there are any of the following warnings and corresponding details, select this menu. . No key warning . Low fuel warning . Low washer fluid warning . Parking brake release warning . Door/lift gate open warning (Hardtop mod- els) .
2-30 Instruments and controls VEHICLE SECURITY S Y STEM (if so equipped) The vehicle security system provides visual and audio alarm signals if someone opens the doors or lift gate/trunk when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.
. Unlocking the door or opening the lift gate/ trunk without using the button on the Intelligent K ey, the request switch or the key. (Even if the door is opened by releasing the door inside lock knob, the alarm will activate.
2-32 Instruments and controls service as soon as possible. Please bring all registered keys that you have when visiting a NISSAN dealer for service. WARNING In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident.
SIC3664 T ype A SIC4395 T ype B SIC3922 T ype C The windshield wiper and washer operates when the ignition switch is in the ON position. Push the lever down to operate the wiper at the following speed: * 1 INT (T ype A or T ype C) — intermittent operation can be adjusted by turning the knob toward * A (Slower) or * B (Faster) .
2-34 Instruments and controls SIC4017 RAIN-SENSING AUTO WIPER S YS- TEM (if so equipped) The rain-sensing auto wiper system can auto- matically turn on the wipers and adjust the wiper speed depending on the rainfall and the vehicle speed by using the rain sensor located on the upper part of the windshield.
WARNING In freezing temperatures the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window. CAUTION . Do not operate the washer continu- ously for more than 30 seconds.
2-36 Instruments and controls The rear window wiper and washer operate when the ignition switch is in the ON position. T urn the switch clockwise from the OFF position to operate the wiper.
XENON HEADLIGHTS (if so equipped) WARNING HIGH VOL TAGE . When xenon headlights are on, they produce a high voltage. T o prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at a NISSAN dealer. .
2-38 Instruments and controls SIC3669 Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically. T o set the autolight system: 1. Make sure the headlight switch is in the AUT O position * 1 .
For automatic headlights off delay setting, see “V ehicle information and settings” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section. SIC3670 Headlight beam select * 1 T o select the low beam, put the lever in the neutral position as shown.
2-40 Instruments and controls headlights turn off automatically. Daytime running light system (Canada only) The daytime running lights automatically illumi- nate when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position or in the position.
SIC3672 FOG LIGHT SWITCH (if so equipped) T o turn the fog lights on, turn the headlight switch to the position, then turn the switch to the position. T o turn them off, turn the switch to the OFF position. The headlights must be on for the fog lights to operate.
2-42 Instruments and controls NOTE: If the surface temperature of the steering wheel is above 68 8 F (20 8 C) when the switch is turned on, the system will not heat the steering wheel.
SIC2770 The seats are warmed by built-in heaters. The switches located on the center console and rear doors (if so equipped for rear seats) can be operated independently of each other. 1. Start the engine. 2. Select heat range. * 1 For high heat, push the HI (High) side of the switch.
2-44 Instruments and controls sounds twice and the Blind Spot Indicator light will flash. For additional information, see “Blind Spot W arning (BSW)/Lane Departure Warning (LDW) systems” in the “5.
SIC3587 Center console SIC3651 Cargo area (Hardtop models) SIC3652 Console box — T ype A SIC3653 Console box — T ype B T o use the power outlet, pull the cover as illustrated. CAUTION . The outlet and plug may be hot during or immediately after use.
2-46 Instruments and controls . When not in use, be sure to close the cap. Do not allow water or any liquid to contact the outlet. SIC3588 T o open the ashtray lid, push the lid down and release it * 1 . T o empty the ashtray, pull out * 2 . The cigarette lighter operates when the ignition switch is in the ON position.
CUP HOLDERS CAUTION . Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. . Use only soft cups in the cup holder. Hard objects can injure you in an accident.
2-48 Instruments and controls SIC4742 CrossCabriolet models The cup holders are located on the center of rear seat. SIC3589 SUNGLASSES HOLDER (Hardtop models) WARNING Keep the sunglasses holder closed while driving to prevent an accident. T o open the sunglasses holder, push * 1 .
SIC3590 GL OVE BOX WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop. T o open the glove box, pull the handle * 1 . T o close, push the lid in until the lock latches. T o lock * 2 /unlock * 3 the glove box, use the mechanical key .
2-50 Instruments and controls SIC3591 Rear Rear (Hardtop models) T o open, push the knob * 1 and pull out * 2 . SIC3593 ST ORAGE BOX (if so equipped) T o open, push the storage box lid * 1 as illustrated. The inner tray can be removed * 2 as illustrated.
SIC3656 T ype B T ype B T o open the cargo floor box, push * A . T o close, push the lid until the lock latches. The net partitions can be removed * B to make a larger storage space. The cargo floor box needs to be removed when you need a spare tire. (See “Flat tire” in the “6.
2-52 Instruments and controls SIC3595 CARGO COVER (if so equipped for Hardtop models) The cargo cover keeps the contents in the cargo area hidden from the outside. T o use the cargo cover, pull it out and hang both sides on the hooks * 1 . T o use the sub cover, hang the straps on the back of the head restraint * 2 .
SIC3596 LUGGAGE HOOKS (Hardtop models) WARNING . Always make sure that the cargo is properly secured. Use the suitable ropes and hooks. . Unsecured cargo can become dan- gerous in an accident or sudden stop. CAUTION Do not apply a total load of more than 22 lb (10 kg) * A or 7 lb (3 kg) * B to a single hook.
2-54 Instruments and controls WARNING . Do not place anything over the luggage cover during soft top op- eration. . Do not place or leave objects under the cover that may push the cover up. . Do not place items on sides that intrude into luggage cover area.
CAUTION Use care when placing or removing items from the roof rack. If you cannot comfortably lift the items onto the roof rack from the ground, use a ladder or stool. SIC3505 COA T HOOKS (Hardtop models) The coat hooks are equipped beside the rear personal lights.
2-56 Instruments and controls SIC3283A 1. Driver side window 2. Front passenger side window 3. Rear left passenger side window 4. Rear right passenger side window 5. Window lock button Main power window switch (driver’s side) T o open or close the window , push down * A or pull up * B the switch and hold it.
SIC3285 Hardtop models SIC4743 CrossCabriolet models Automatic operation The automatic function is available for the switch that has an mark on its surface. T o fully open or close the window, completely push down or pull up the switch and release it; it need not be held.
2-58 Instruments and controls Automatic window lowering (CrossCa b- riolet models) When the soft top operating switch is pressed, the power windows will automatically be low- ered completely. The windows do not rise automatically after the soft top open/close operation is completed.
AUT OMA TIC MOONROOF AND SUN- SHADES The moonroof and sunshades only operates when the ignition switch is in the ON position. The automatic moonroof and sunshades are operational for about 45 seconds, even if the ignition switch is pushed to the OFF position.
2-60 Instruments and controls The auto reverse function can be activated when the moonroof and sunshades are closed by automatic operation when the ignition switch is in the ON position or for about 45 seconds after the ignition switch is pushed to the OFF position.
SIC3250 PERSONAL LIGHTS (Hardtop models) Rear Push the button as illustrated to turn the light on or off. SIC4239 INTERIOR LIGHT CONTROL SWIT CH The interior light control switch has three positions: ON, DOOR and OFF. ON position When the switch is in the ON position * 1 the map lights and rear personal lights will illumi- nate.
2-62 Instruments and controls — remain on while the door is opened. When the door is closed, the lights go off. OFF position When the switch is in the OFF position * 3 , the lights will not illuminate, regardless of the condition. CAUTION Do not use for extended periods of time with the engine stopped.
SIC2131A When the switch is in the ON position * 1 , the light illuminates while the lift gate is opened. When the lift gate is closed, the light will turn off.
2-64 Instruments and controls WARNING . Do not use the HomeLink ® Universal T ransceiver with any garage door opener that lacks safety stop and reverse features as required by federal safety standards. (These standards became effective for opener models manufactured after April 1, 1982) .
JVI0429X 3. Press and hold the programmed HomeLink ® button and observe the indicator light. . If the indicator light * 1 is solid/contin- uous, programming is complete and your device should activate when the HomeLink ® button is pressed and re- leased.
2-66 Instruments and controls indicator light will flash slowly and then rapidly after several seconds upon successful program- ming. DO NOT release until the HomeLink ® indicator light flashes slowly and then rapidly . When the indicator light flashes rapidly, both buttons may be released.
at: www .homelink.com or 1-800-355-3515. The HomeLink ® Universal T ransceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLink ® button that was just programmed. This proce- dure will not affect any other programmed HomeLink ® buttons.
2-68 Instruments and controls MEMO.
3 Pre-driving checks and adjustments Keys .............................................................................................. 3-3 Intelligent Key system ......................................................... 3-3 Mechanical key ..........
Tilt/telescopic steering .......................................................... 3-46 Manual operation .............................................................. 3-46 Electric operation ..........................................................
A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet) , not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record any key numbers so it is very important to keep track of your key number plate.
3-4 Pre-driving checks and adjustments nents when registering new keys, be sure to take all Intelligent Keys that you have to the NISSAN dealer. CAUTION . Be sure to carry the Intelligent Key with you when driving. The Intelli- gent Key is a precision device with a built-in transmitter.
CAUTION Always carry the mechanical key in- stalled in the key. V ALET HAND-OFF When you have to leave a key with a valet, give them the Intelligent Key itself after removing the mechanical key to protect your belongings.
3-6 Pre-driving checks and adjustments Crosscabriolet models . T urning the driver’s door key cylinder to the rear of the vehicle * 2 will lock all doors. . T urning the driver’s door key cylinder once to the front of the vehicle * 1 will unlock the driver’s door.
SP A2300 L OCKING WITH POWER DOOR L OCK SWIT CH Operating the power door lock switch will lock or unlock all the doors. The switches are located on the driver’s and front passenger’s door armrests.
3-8 Pre-driving checks and adjustments SP A2433 CHILD SAFETY REAR DOOR L OCK (Hardtop models) The child safety rear door locks help prevent doors from being opened accidentally, espe- cially when small children are in the vehicle. When the levers are in the lock position * 1 , the rear doors can be opened only from the outside.
computer. . When the vehicle is parked near a parking meter. In such cases, correct the operating conditions before using the Intelligent K ey function or use the mechanical key. Although the life of the battery varies depending on the operating conditions, the battery’s life is approximately 2 years.
3-10 Pre-driving checks and adjustments SP A2074 INTELLIGENT KEY OPERA TING RANGE The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range from the request switch * 1 .
prevent the Intelligent Key from being left in the vehicle. . The door handle request switch is opera- tional only when the Intelligent Key has been detected by the Intelligent Key system. . T o prevent the Intelligent Key from being left inside the vehicle or the trunk, make sure you carry the key with you and then lock the doors or the trunk.
3-12 Pre-driving checks and adjustments When you carry the Intelligent Key with you, you can lock or unlock all doors by pushing the door handle request switch * A (driver’s or front passenger’s) or the lift gate request switch * B within the range of operation.
. When the Intelligent Key is placed inside or near metallic materials. Unlocking doors 1. Push the door handle request switch * A or the lift gate request switch * B once while carrying the Intelligent Key with you. 2. The hazard indicator flashes once and the outside chime sounds once.
3-14 Pre-driving checks and adjustments sound and the trunk will open. BA TTER Y SAVER S Y STEM When all the following conditions are met for a period of time, the battery saver system will cut off the power supply to prevent battery dis- charge. . The ignition switch is in the ACC position, and .
TROUBLESHOO TING GUIDE Symptom Possible cause Action to take When pushing the ignition switch to stop the engine The SHIFT P warning appears on the display and the inside warning chime sounds con- tinuously. The shift lever is not in the P (Park) position.
3-16 Pre-driving checks and adjustments WARNING The Intelligent Key transmits radio waves when the buttons are pushed. The FA A advises that radio waves may affect aircraft navigation and commu- nication systems. Do not operate the Intelligent Key while on an airplane.
SP A2867 T ype C * 1 L OCK button * 2 UNL OCK button * 3 Power lift gate button (if so equipped) * 4 P ANIC button * 5 TRUNK button (CrossCabriolet models) HOW T O USE REMO TE KEYLESS ENTR Y S Y STEM .
3-18 Pre-driving checks and adjustments button * 2 again until the window opens completely. The door windows can be opened or closed by turning the mechanical key in a door lock. (See “Doors” earlier in this section.) Opening/closing lift gate (if so equipped) 1.
Hazard indicator and horn mode: DOOR LOCK DOOR UNLOCK TRUNK UNLOCK Intelligent Key system (Using door handle or lift gate/ trunk request switch) HAZARD - twice OUTSIDE CHIME - twice HAZARD - once OUTS.
3-20 Pre-driving checks and adjustments SP A2437 1. Pull the hood lock release handle * 1 located below the instrument panel; the hood will then spring up slightly. 2. Pull the lever * 2 up at the front of the hood with your fingertips and raise the hood.
SP A2438 OPERA TING MANUAL LIFT GA TE T o open the lift gate, unlock it and push the opener switch * A . Pull up the lift gate to open. The lift gate can be unlocked by: . pushing the unlock button on the Intelligent Key twice. . pushing the lift gate request switch (if so equipped) .
3-22 Pre-driving checks and adjustments SP A2439 SP A2462 SP A2463 SP A2440 Power open When the lift gate is fully closed, the lift gate will fully open automatically by: . pushing the power lift gate switch * A on the instrument panel . pushing the lift gate opener switch * B .
The hazard flashes 4 times and the outside chime sounds when the lift gate starts closing. Reverse function The power lift gate will reverse immediately if one of the following actions is performed during power open or power close. . pushing the power lift gate switch * A on the instrument panel .
3-24 Pre-driving checks and adjustments SP A2464 Safe Mode If the gas stays of the lift gate * 1 lose pressure, the power lift gate safe mode is activated. When the safe mode is activated, the lift gate intermittently closes. Then the lift gate will be pulled to the closed and latched position by a motor.
SP A1915 LIFT GA TE RELEASE If the lift gate cannot be opened due to a discharged battery, follow these steps. 1. Remove the cover inside of the lift gate with a suitable tool. 2. Move the lever toward the direction * A as illustrated to open the lift gate.
3-26 Pre-driving checks and adjustments SP A2866-A TRUNK OPEN REQUEST SWIT CH The trunk lid can be opened by pushing the trunk open request switch * A when the Intelligent Key is within the operating range of the trunk lock/unlock function regardless of the inside lock knob position.
you. See “Keys” earlier in this section. T o connect the power to the trunk lid, push the switch to the ON * B position. SP A2870 INTERIOR TRUNK LID RELEASE WARNING Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured.
3-28 Pre-driving checks and adjustments SP A2872 Interior/exterior view 1. Soft top indicator light (on the combination meter) 2. Soft top operating switch 3. T op lock hole 4. Soft top 5. Rear parcel shelf 6. Skylight glass 7. Rear window 8. T op storage lid 9.
Be sure to follow the operating instructions, and all the warnings and cautions in this section. Improper operation of the top could cause a system malfunction, damage, or dete- rioration of the top material and related parts. SP A2873 WARNING . Do not operate the top when there is not enough clearance behind the vehicle.
3-30 Pre-driving checks and adjustments JVP0094X CAUTION . Make sure the parking area is clear of obstacles and there is enough clearance over the top (for example, in a garage or a covered area) . More than approximately 10 ft (3 m) from the ground * A , more than approxi- mately 5.
JVP0045X WARNING . Never install a cover or film (for example window tint) on the sky- light glass. This may cause the dual pop-up roll bars to operate impro- perly and could result in serious injury or death in the event of a rollover. (see “Dual pop-up roll bar system (CrossCabriolet models)” in the “1.
3-32 Pre-driving checks and adjustments . Do not place anything in the top storage area. The top will not fit there properly, and this could da- mage the top and/or the vehicle body. . Do not sit or place anything on the top, rear parcel shelf, inner flaps, storage lid and trunk lid, especially when the top is being operated.
SP A2875 CAUTION . Keep all parts of the top linkage clear of obstructions, or the top latch may not be securely locked. . Do not place anything in the top storage area. Cargo that contacts the top could damage the top and/ or the vehicle body. See Caution label * B attached in the trunk.
3-34 Pre-driving checks and adjustments fully opened or fully closed position. When the soft top is operating, and any of the following conditions occur, the top will stop operating. . When the shift lever is in the R (Reverse) position. . When the vehicle moves at a speed of 3 MPH (5 km/h) or more.
NOTE: If you release the switch and press it again while the top is being opened, the top will slightly move to the closing direction, then start moving to the opening direction again. The top is designed to move in this way. It is not a malfunction. SP A2633 CL OSING THE T OP 1.
3-36 Pre-driving checks and adjustments JVP0049X Opening the soft top Push the ignition switch to the OFF position and make sure to carry the Intelligent Key with you.
TROUBLESHOO TING GUIDE If the soft top stops halfway during operation or does not operate normally, follow the procedures shown in the following table. If the procedures in the following table do not solve the symptom, immediately contact a NISSAN dealer for the inspection.
3-38 Pre-driving checks and adjustments IF THE T OP DOES NO T OPEN OR CL OSE ELECTRICALL Y If you cannot operate the soft top with the operating switch, first check whether all the following operating conditions are met. . V ehicle is stopped . Ignition switch is ON (Run the engine when operating the top.
JVP0097X e. Release the storage lid locks. Pull back the left and right side trim in the trunk room. Push linkage * A on the left and right using the wheel nut wrench or suitable tool to release the storage lid locks * B . CAUTION Use gloves or a cloth to protect your hands when releasing the storage lid locks.
3-40 Pre-driving checks and adjustments JVP0038X f. Push and hold the lever * C toward the front of the vehicle to release the storage lid. g. Close the trunk lid. CAUTION Make sure to close the trunk lid before opening the storage lid. The storage lid may contact the trunk lid and damage it.
j. Move the inner flap * E and * F in the direction of the arrows, then secure the flaps with tape or string. 3. Close the soft top. JVP0041X a. Pull up the soft top simultaneously from the right and left side of the vehicle.
3-42 Pre-driving checks and adjustments soft top forward all the way. JVP0043X c. Close the storage lid. CAUTION Make sure to close the storage lid completely. The storage lid may contact the soft top and damage it. JVP0044X d. Close the front and rear parts of the soft top at the same time as illustrated.
SP A2689 4. Lock the front part of the soft top. a. Remove the cap * 1 as illustrated. b. Insert tool * 2 (located in the trunk) into the hole and turn clockwise. CAUTION . After closing the top manually, have the system checked and/or repaired by a NISSAN dealer as soon as possible.
3-44 Pre-driving checks and adjustments SP A2441 OPENING FUEL -FILLER DOOR T o open the fuel-filler door, push the opener switch located below the instrument panel. T o lock, close the fuel-filler door securely. FUEL -FILLER CAP WARNING . Gasoline is extremely flammable and highly explosive under certain conditions.
. Insert the cap straight into the fuel- filler tube, then tighten the fuel-filler cap until a single click is heard. Failure to tighten the fuel-filler cap properly may cause the mal- function indicator light (MIL) to illuminate.
3-46 Pre-driving checks and adjustments to turn off the L OOSE FUEL CAP warning after tightening the fuel cap. WARNING . Do not adjust the steering wheel while driving. Y ou could lose control of your vehicle and cause an acci- dent. . Do not adjust the steering wheel any closer to you than is necessary for proper steering operation and comfort.
SP A2444A ELECTRIC OPERA TION Tilt or telescopic operation Move the lever to adjust the steering wheel up or down, forward or rearward to the desired position.
3-48 Pre-driving checks and adjustments SIC2872 CROSSCABRIOLET MODELS 1. T o block out glare from the front, swing down the sun visor * 1 . 2. T o block glare from the side, remove the sun visor from the center mount and swing it to the side * 2 . SP A2447 INSIDE MIRROR Adjust the height and the angle of the inside mirror to the desired position.
SP A2422A T ype A SP A2450 T ype B Automatic anti-glare type The inside mirror is designed so that it automatically changes reflection according to the intensity of the headlights of the following vehicle. The anti-glare system will be automatically turned on when the ignition switch is pushed to the ON position.
3-50 Pre-driving checks and adjustments SP A2319 Adjusting outside mirrors The outside mirror control switch is located on the armrest. The outside mirror will operate only when the ignition switch is in the ACC or ON position. T urn the switch right or left to select the right or left side mirror * 1 , then adjust using the control switch * 2 .
SIC2064 V ANITY MIRROR T o use the front vanity mirror, pull down the sun visor and pull up the cover. The automatic drive positioner system has two features: .
3-52 Pre-driving checks and adjustments Initialize entry/exit function If the battery cable is disconnected, or if the fuse opens, the entry/exit function will not work though this function was set on before.
Push the ignition switch to the OFF position, and then push the button on the Intelligent Key . The driver’s seat, steering wheel (if so equipped) and outside mirrors will move to the memorized position. Confirming memory storage . Push the ignition switch to the ON position and push the SET switch.
3-54 Pre-driving checks and adjustments MEMO.
4 Monitor, heater, air conditioner, audio, phone and voice recognition systems Safety note .................................................................................. 4-3 Center multi-function control panel (models with color display screen) ..
Steering-wheel-mounted controls for audio (if so equipped) ..................................................................... 4-86 Antenna ............................................................................... 4-87 Car phone or CB radio ..
WARNING . Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electric shock. . Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock.
4-4 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2268 Without navigation system 1. “ INFO ” vehicle and navigation information but- ton (P .4-9) 2. “ ST ATUS ” status display button (P .4-9) 3. Multi-function controller (P .
HOW T O USE MUL TI-FUNCTIO N CONTROLLER Choose an item on the display using the main directional buttons * 2 (or additional directional buttons * 6 with navigation system) or center dial * 3 , and push the ENTER button * 1 for operation.
4-6 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2473 Selecting the item: T ouch an item to select it. T o select the “Audio” settings, touch the “ Audio” area * 1 on the screen. T ouch the BACK * 2 key to return to the previous screen.
. Delete: Deletes the last character that has been input with one touch. Push and hold the button to delete all of the characters. . OK: Completes character inputs. T ouch screen maintenance If you clean the display screen, use a dry, soft cloth. If additional cleaning is necessary, use a small amount of neutral detergent with a soft cloth.
4-8 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2477 Models with navigation system JVH0179M Models without navigation system HOW T O SELECT MENUS ON THE SCREEN V ehicle functions are viewed on the display screen in menus.
HOW T O USE ST A TUS BUTT ON Y ou can check information related to the audio, climate control system, fuel consumption and navigation system (if so equipped) by pushing the ST A TUS button repeatedly.
4-10 Monitor, heater, air conditioner, audio, phone and voice recognition systems V ehicle information display 1. Push the INFO button on the control panel. 2. Select an item from the INFO menu. 3. After viewing or adjusting the information on the following screens, push the BACK button to return to the INFO menu.
Fuel Economy information The approximate distance to empty, average fuel economy and current fuel economy will be displayed for reference. T o reset the average fuel economy (Avg Fuel Econ or Average Fuel Economy) , select the “Reset Fuel Eco” or “Reset” key.
4-12 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2482 Models with navigation system JVH0184M Models without navigation system 1. Set the interval (mileage) of the maintenance schedule. T o determine the recommended maintenance interval, refer to your “NISSAN Service and Maintenance Guide”.
SAA2483 Others information (models with naviga- tion system) The Others information display will appear when pushing the INFO button and selecting the “Others” key. GPS Position: For the details of this item, see the separate Navigation System Owner’s Manual.
4-14 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2485 Models with navigation system SAA2740 Models without navigation system Audio settings The display as illustrated will appear when pushing the SETTING button and selecting the “ Audio” key.
SAA2554 Example V olume and Beeps settings (models with navigation system) The display as illustrated will appear when pushing the SETTING button, selecting the “V olume & Beeps” key. Audio Volume: T o increase or decrease the audio volume, select the “Audio Volume” and adjust it with the multi-function controller.
4-16 Monitor, heater, air conditioner, audio, phone and voice recognition systems Driver Assistance settings (if so equipped) For the details of the “Driver Assistance” settings, see the following items: . “BSW system operation” in the “5. Starting and driving” section.
SAA2115 Display settings (models without navi- gation system) The “Display” screen will appear when pushing the SETTING button on the control panel. Display: T o turn off the screen, push the ENTER button and turn the “ON” indicator off. When any mode button is pushed with the screen off, the screen turns on for further operation.
4-18 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA3151 Models with navigation system Comfort settings The display as illustrated will appear when pushing the SETTING button, selecting the “Others” key and then selecting the “Comfort” key.
unlocked if the door unlock operation is per- formed again within 60 seconds. When this item is turned to OFF , all the doors will be unlocked after the door unlock operation is performed once. Intelligent Key Lock/Unlock: When this item is turned to ON, door lock/ unlock function by pushing the door handle request switch will be activated.
4-20 Monitor, heater, air conditioner, audio, phone and voice recognition systems to ON, the 12-hour clock is displayed. Offset (hour)/(min) (models with naviga- tion system)/Clock Adjust (models without navigation system) : Adjust the time by increasing or decreasing per hour or per minute.
SAA1092 Models without navigation system The display illustrated will appear when pushing the SETTING button and selecting the “Lan- guage & Units” key. Select Language: Select the “Select Language” key. Choose “English”, “Franc ¸ ais” or “Espan ˜ ol” for your favorite display appearance.
4-22 Monitor, heater, air conditioner, audio, phone and voice recognition systems vehicle in a safe location and apply the parking brake. SAA2492 Full Screen Display: The full screen display will appear when select- ing the “Full Screen Display” key.
— Maximum Size: 2-MB — Colors: 32768 (15-bit) — Maximum File Name lengths: 253-Bytes — Maximum Folders: 500 — Maximum Images per Folder: 1024 . If an electronic device (such as a digital camera) is directly connected to the vehicle using a USB cable, no image will be displayed on the screen.
4-24 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA1896 HOW T O READ THE DISPLA YED LINES Guiding lines which indicate the vehicle width and distances to objects with reference to the vehicle body line * A are displayed on the monitor.
SAA1897 1. Visually check that the parking space is safe before parking your vehicle. 2. The rear view of the vehicle is displayed on the screen * A when the shift lever is moved to the R (Reverse) position. SAA1898 3. Slowly back up the vehicle adjusting the steering wheel so that the predictive course lines * B enter the parking space * C .
4-26 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA1978 DIFFERENCE BETWEEN PREDICTIVE AND ACTUAL DIST ANCES Backing up on a steep uphill When backing up the vehicle up a hill, the distance guide lines and the vehicle width guide lines are shown closer than the actual distance.
the hill is viewed in the monitor closer than it appears. SAA1923 Backing up near a projecting object The predictive course lines * A do not touch the object in the display . However, the vehicle may hit the object if it projects over the actual backing up course.
4-28 Monitor, heater, air conditioner, audio, phone and voice recognition systems course. SAA2404 Models with navigation system SAA2606 Models without navigation system PREDICTIVE COURSE LINE SETTINGS T o turn ON or OFF the predictive course line display , push the SETTING button, select the “Camera” key and push the ENTER button.
. When the temperature is extremely high or low, the screen may not clearly display objects. This is not a malfunction. . When strong light is directly coming on the camera, objects may not be displayed clearly. This is not a malfunction. . V ertical lines may be seen in objects on the screen.
4-30 Monitor, heater, air conditioner, audio, phone and voice recognition systems When the shift lever is shifted into the R (Reverse) position, the monitor display shows view to the rear of the vehicle. The system is designed as an aid to the driver in detecting large stationary objects to help avoid damaging the vehicle.
JVH0364X HOW T O SWIT CH THE DISPLA Y * A : Original screen before the RearView Monitor is operated * B : Rear-wide view screen * C : Rear view screen * 1 : Shift lever is moved into the R(Reverse) position * 2 : Shift lever is moved out of the R (Reverse) position * 3 : Select the “View” key on the screen .
4-32 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA1896 Rear view Guiding lines which indicate the vehicle width and distances to objects with reference to the bumper line * A are displayed on the monitor. Distance guide lines: Indicate distances from the bumper.
HOW T O PARK WITH PREDICTIVE COURSE LINES WARNING . Always turn and check that it is safe to park your car before backing up. Always back up slowly. . Use the displayed lines as a refer- ence. The lines are highly affected by the number of occupants, fuel level, vehicle position, road condi- tion and road grade.
4-34 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA1897 1. Visually check that the parking space is safe before parking your vehicle. 2. The rear view of the vehicle is displayed on the screen * A as illustrated when the shift lever is moved to the R (Reverse) position.
SAA1978 Difference between predictive and actual distances Backing up on a steep uphill: When backing up the vehicle up a hill, the distance guide lines and the vehicle width guide lines are shown closer than the actual distance.
4-36 Monitor, heater, air conditioner, audio, phone and voice recognition systems the hill is viewed in the monitor closer than it appears. SAA1923 Backing up near a projecting object : The predictive course lines * A do not touch the object in the display .
course. HOW T O ADJUST THE SCREEN T o adjust the Display ON/OFF , Brightness, Tint, Color, Contrast and Black Level of the RearView Monitor, push the SETTING button with the RearView Monitor on, select the item key and adjust the level using the multi-function con- troller.
4-38 Monitor, heater, air conditioner, audio, phone and voice recognition systems . The MOD system is not designed to detect surrounding stationary ob- jects. If the MOD system detects moving objects behind the vehicle, a yellow frame will be displayed on the camera image and a chime sounds.
JVH0365X T urning the MOD system on or off 1. Push the SETTING button, select the “Driver Assistance” key and push the ENTER button. JVH0345X 2. Then select the “Moving Object Detection (MOD)” key and push the ENTER button. JVH0344X When the MOD system is turned on, the MOD icon * 1 is displayed.
4-40 Monitor, heater, air conditioner, audio, phone and voice recognition systems Camera maintenance If dirt, rain or snow accumulates on the camera, the MOD system may not operate properly. Clean the camera. The camera washer operates automatically when dirt is detected on the camera during driving.
Open or close, and adjust the air flow direction of ventilators. : This symbol indicates that the ventilators are closed. : This symbol indicates that the ventilators are open. WARNING . The air conditioner cooling function operates only when the engine is running.
4-42 Monitor, heater, air conditioner, audio, phone and voice recognition systems For the models with the color display screen, push the “ST A TUS” button to display the heater and air conditioner status screen. (See “How to use ST A TUS button” earlier in this section.
SAA2834 T ype B 1. “ AUT O” automatic air conditioner ON button/ T emperature control dial (driver side) 2. “ A/C” air conditioner ON/OFF button 3. “ ” intake air control button 4. “ ” fan speed control dial/ON/OFF button 5. “ ” upper vent system button 6.
4-44 Monitor, heater, air conditioner, audio, phone and voice recognition systems A visible mist may be seen coming from the ventilators in hot, humid conditions as the air is cooled rapidly. This does not indicate a mal- function. Heating (A/C OFF) The air conditioner does not activate in this mode.
Upper vent system When the “ ” upper vent system button is pushed, the air flow against the driver’s or passenger’s upper body becomes gentle. The indicator light on the button will come on.
4-46 Monitor, heater, air conditioner, audio, phone and voice recognition systems AUDIO OPERA TION PRECAUTION S Radio Push the ignition switch to the ACC or ON position and push the radio band select button to turn on the radio. If you listen to the radio with the engine not running, the ignition switch should be pushed to the ACC position.
Static and flutter: During signal interference from buildings, large hills or due to antenna position, usually in conjunction with increased distance from the station transmitter, static or flutter can be heard. This can be reduced by lowering the treble setting to reduce the treble response.
4-48 Monitor, heater, air conditioner, audio, phone and voice recognition systems . During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely. . The player may skip while driving on rough roads.
or ventilate the player completely. . The player may skip while driving on rough roads. . The CD/DVD player sometimes cannot function when the passenger compartment temperature is extremely high. Decrease the temperature before use. . Only use high quality 4.
4-50 Monitor, heater, air conditioner, audio, phone and voice recognition systems . D TS and DTS 2.0 “ ” are registered trademarks of DTS, Inc. Parental level (parental control) : DVDs with the parental control setting can be played with this system.
regulatory reasons, even when the vehicle is parked. This system supports various USB memory devices, USB hard drives and iPod ® players. Some USB devices may not be supported by this system. . Partitioned USB devices may not be played correctly . . Some characters used in other languages (Chinese, Japanese, etc.
4-52 Monitor, heater, air conditioner, audio, phone and voice recognition systems reduces certain parts of sound that seem inaudible to most people. . WMA — Windows Media Audio (WMA) is a compressed audio format created by Micro- soft as an alternative to MP3.
. The playback order is the order in which the files were written by the writing software, so the files might not play in the desired order. . Music playback order of compressed audio files is as illustrated.
4-54 Monitor, heater, air conditioner, audio, phone and voice recognition systems Specification chart (for FM-AM radio with Compact Disc (CD) changer) : Supported media CD, CD-R, CD-RW Supported file systems CD, CD-R, CD-RW: ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported.
Specification chart (for FM-AM-SAT radio with Compact Disc (CD) player) : Supported media CD, CD-R, CD-RW, DVD-ROM*5, DVD±R*5, DVD±RW*5, DVD±R DL*5, USB2.0 Supported file systems CD, CD-R, CD-RW, DVD-ROM*5, DVD±R, DVD±RW, DVD±R DL: ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported.
4-56 Monitor, heater, air conditioner, audio, phone and voice recognition systems *3 Available codes depend on what kind of media, versions and information are going to be displayed. *4 When VBR files are played, the playback time may not be displayed correctly.
T roubleshooting guide: Symptom Cause and Countermeasure Cannot play Check if the disc or USB device was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player, and if there is, wait until the condensation is gone (about 1 hour) before using the player.
4-58 Monitor, heater, air conditioner, audio, phone and voice recognition systems Compressed Video Files (models with navigation system) Explanation of terms: . DivX ® - DivX ® refers to the DivX ® codec owned by DivX, Inc. used for a lossy compression of video based on MPEG-4.
Bluetooth ® Audio player (models with navigation system) Bluetooth ® is a trademark owned by Bluetooth SIG, Inc. and li- censed to Clarion Co., Ltd. .
4-60 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA3473 FM-AM RADIO WITH COMPACT DISC (CD) CHANGER 1. CD EJECT button 2. ON·OFF/VOLUME control knob 3. Radio station and CD selector buttons 4. Radio tuning / MP3/WMA folder selector / AUDIO control knob 5.
selecting mode as follows. Bass ? T reble ? Fade ? Balance ? Speed Sensitive V olume ? Beep Rotate the Audio control knob to adjust Bass, T reble, Fade and Balance to the desired level. Fade adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers.
4-62 Monitor, heater, air conditioner, audio, phone and voice recognition systems * 1 to * 6 Station memory operations: 12 stations/channels can be set for the FM band (6 for FM1, 6 for FM2) and 6 stations can be set for the AM band. 1. Choose the radio band AM, FM1 or FM2 using the radio band select button.
FF (Fast Forward) , REW (Re- wind)/APS (Automatic Program Search) FF , APS REW: Push the FF or REW button for more than 1.5 seconds while a CD is being played to fast forward or rewind through the track. When the button is released, the compact disc will return to normal play speed.
4-64 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA3474 1. CD EJECT button 2. ON·OFF/VOLUME control knob 3. Radio station and CD selector buttons 4. Radio tuning/AUDIO control knob 5. Radio SCAN (tuning) button 6. CD RPT (repeat)/RDM (random) play button 7.
SAA1852 Without navigation system 1. AM·FM band select button 2. DISC button 3. AUX/SA T band select button FM-AM-SA T RADIO WITH COMP ACT DISC (CD) PLA YER For all operation precautions, see “ Audio opera- tion precautions” earlier in this section.
4-66 Monitor, heater, air conditioner, audio, phone and voice recognition systems FM-AM-SA T radio operation radio (FM/AM) band select : Pushing the radio band select button will change the band as fo.
3. Push and hold the desired station preset button * 1 to * 6 until the radio mutes. 4. The station indicator will then come on and the sound will resume. Memorizing is now complete. 5. Other buttons can be set in the same manner. If the battery cable is disconnected, or if the fuse opens, the radio memory will be erased.
4-68 Monitor, heater, air conditioner, audio, phone and voice recognition systems will start to play. Menu (models with navigation system) : When the “Menu” key on the display is selected while the CD is being played, the menu screen will be displayed.
DVD (Digital V ersatile Disc) PLA YER OPERA TION (models with navigation system) Precautions Start the engine when using the DVD entertain- ment system. Movies will not be shown on the front display while the vehicle is in any drive position to reduce driver distraction.
4-70 Monitor, heater, air conditioner, audio, phone and voice recognition systems button again. DVD operation keys: When the DVD is playing without the operation screen being shown, you may use the touch screen to select items from the displayed video.
Title Menu (DVD-VIDEO) : Some menus specific to each disc will be shown. For details, see the instructions on the disc. Title Search (DVD-VIDEO, DVD-VR) : The scene with the specified title will be displayed each time the “+” side or “ − ” side is selected.
4-72 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA3557 USB MEMORY OPERA TION (if so equipped) Audio main operation Open the console lid and connect a USB memory as illustrated. Then, push the DISC·AUX or AUX button repeatedly to switch to the USB memory mode.
SAA2501 Models with navigation system SAA2611 Models without navigation system Audio file operation or PLA Y : When the DISC·AUX or AUX button is pushed with the system off and the USB memory inserted, the system will turn on.
4-74 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2502 Menu (models with navigation system) : There are some options available during play- back. Select one of the following options that are displayed on the screen if necessary .
Operation keys: T o operate the USB memory, select the desired key displayed on the operation screen using the multi-function controller. Pause Select the “ ” key to pause the movie file. T o resume playing the movie file, select the “ ” key. Play Select the “ ” key to start playing a movie file, for example, after pausing a movie file.
4-76 Monitor, heater, air conditioner, audio, phone and voice recognition systems the “OK” key. The specified folder/file will be played. . Display T o adjust the image quality of the screen, select the preferred adjustment items.
Bluetooth trademark: Bluetooth ® is a trademark owned by Bluetooth SIG, Inc. and li- censed to Clarion Co., Ltd. SAA2505 Connecting procedure 1. Push the SETTING button and select the “Bluetooth” key. SAA2506 2. Select the “Connect Bluetooth” key.
4-78 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2507 3. A confirmation screen will be displayed. Select “No” . Note: Selecting “Y es” will only connect the hands free phone portion of a Bluetooth ® device.
SAA2510 Audio main operation Push the ignition switch to the ACC or ON position. Then, push the DISC·AUX button repeatedly to switch to the Bluetooth ® audio mode. If the system has been turned off while the Bluetooth ® audio device was playing, push- ing the ON·OFF/VOL control knob will start the Bluetooth ® audio device.
4-80 Monitor, heater, air conditioner, audio, phone and voice recognition systems following items. . Shuffle Choose “Shuffle OFF”, “Shuffle All T racks” and “Shuffle Group”. . Repeat Choose from “Repeat OFF”, “Repeat 1 T rack” , “Repeat All T racks” and “Repeat Group” .
SAA3344 iPod ® PLA YER OPERA TION (if so equipped) Connecting iPod ® Open the console lid and connect the iPod ® cable to the USB connector. If compatible, the battery of the iPod ® is charged while the connection to the vehicle.
4-82 Monitor, heater, air conditioner, audio, phone and voice recognition systems . Second generation iPod touch ® (firmware version 2.1.1) . First generation iPod nano ® (firmware ver- sion 1.3.1) . Second generation iPod nano ® (firmware version 1.
REPEA T (RPT) , RANDOM (RDM) : When the RPT button is pushed while a track is being played, the play pattern can be changed as follows: SAA3342 AUXILIARY INPUT JACKS (if so equipped) The auxiliary input jacks are located in the center console.
4-84 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2496 Models with navigation system SAA1567 Models without navigation system AUX Menu When the “Menu” key on the display is selected while in the AUX mode, the menu screen will be displayed.
. A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer edges with the side of a pen or pencil as illustrated. USB memory . Do not touch the terminal portion of the USB memory . . Do not place heavy objects on the USB memory .
4-86 Monitor, heater, air conditioner, audio, phone and voice recognition systems STEERING-WHEEL -MOUNTED CON- TROLS FOR AUDIO (if so equipped) Menu control switch (models with navi- gation system) or.
ANTENNA Window antenna (for Hardtop models) The antenna pattern is printed inside the rear window . CAUTION . Do not place metalized film near the rear window glass or attach any metal parts to it. This may cause poor reception or noise. . When cleaning the inside of the rear window, be careful not to scratch or damage the rear window antenna.
4-88 Monitor, heater, air conditioner, audio, phone and voice recognition systems When installing a car phone or a CB radio in your vehicle, be sure to observe the following cautions, otherwise the new equipment may adversely affect the electronic control modules and electronic control system harness.
Once a cellular phone is connected to the in- vehicle phone module, no phone connecting procedure is required anymore. Y our phone is automatically connected with the in-vehicle phone module when the ignition switch is pushed to the ON position with the registered cellular phone turned on and carried in the vehicle.
4-90 Monitor, heater, air conditioner, audio, phone and voice recognition systems . If reception between callers is unclear, adjusting the incoming or outgoing call volume may improve the clarity. REGULA T ORY INFORMA TION FCC Regulatory information .
JVH0473X CONNECTING PROCEDURE 1. Push the PHONE button or the button, and select the “Connect Phone” key. SAA2520 2. When a PIN code appears on the screen, operate the compatible Bluetooth ® cellular phone to enter the PIN code. The connecting procedure of the cellular phone varies according to each cellular phone.
4-92 Monitor, heater, air conditioner, audio, phone and voice recognition systems JVH0474X 1. Push the PHONE button and select the “Quick Dial” key. 2. Select the “ Add New” key at the top of the screen. JVH0475X 3. Choose the method for entering the phone- book entry.
instead of “Enter Number by Keypad” in step 3. . Copy from Call History The system will show a list of incoming, outgoing or missed calls that were down- loaded from the connected cellular phone (depending on the phone’s compatibility) . Select one of these entries to save in the Quick Dial.
4-94 Monitor, heater, air conditioner, audio, phone and voice recognition systems allow easy dialing using the NISSAN V oice Recognition system. (See “NISSAN voice recognition system (models with navigation system)” later in this section.) T o delete an entry , select the “Delete” key at step 3.
to use touch screen (models with navigation system)” earlier in this section.) SAA2525 RECEIVING A CALL When you hear a phone ring, the display will change to the incoming call mode. T o receive a call, perform one of the following procedures listed below.
4-96 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA3587 DURING A CALL There are some options available during a call. Select one of the following displayed on the screen if necessary. . Hang up Finish the call. . Use Handset T ransfer the call to the cellular phone.
Delete Quick Dial The Quick Dial entries can be deleted all at the same time or one by one. Download Phonebook Download the contacts registered in a Blue- tooth ® cellular phone. Availability of this function depends on each cellular phone. The memory downloading procedure from the cellular phone also varies according to each cellular phone.
4-98 Monitor, heater, air conditioner, audio, phone and voice recognition systems TROUBLESHOO TING GUIDE The system should respond correctly to all voice commands without difficulty.
WARNING . Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.
4-100 Monitor, heater, air conditioner, audio, phone and voice recognition systems . Do not place the cellular phone in an area surrounded by metal or far away from the in- vehicle phone module to prevent tone quality degradation and wireless connection dis- ruption.
SAA1858 CONTROL BUTTONS 1. PHONE SEND button Push the button to initiate a VR session or answer an incoming call. Y ou can also use the button to skip through system feedback and to enter commands during a call. 2. PHONE END button Push the button to cancel a VR session or end a call.
4-102 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA1858 Giving voice command: 1. Push and release the switch located on the steering wheel. SAA2574 2. A list of commands appears on the screen, and the system announces, “Please say a command after the beep.
How to speak commands: The V oice Recognition System requires a certain way to speak voice commands. Speak normally and clearly in the direction of the microphone (located in front of the rearview mirror) . Every digit of the number must be spoken individually and in a normal manner.
4-104 Monitor, heater, air conditioner, audio, phone and voice recognition systems List of voice commands: COMMAND ACTION “Call/Dial” “<name>” Dials the specified <name>. “Call/Dial” “Redial” Dials the last number. “Call” “Number” “<number>” Dials the specified <number>.
SAA2575 P AIRING PROCEDURE Up to 5 cellular phones can be registered. 1. Push the button on the steering wheel. The system announces the available com- mands. 2. Speak: “Connect Phone” . The system ac- knowledges the command and announces the next set of available commands.
4-106 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2578 5. The system asks the user to speak a name for the phone. Speak: “Y es” . The system acknowledges the command and registers the cellular phone. If the name is too long or too short, the system tells the user, then prompts the user for a name again.
5. Once the call has ended, press the button on the steering wheel. RECEIVING A CALL When the ring tone is heard, press the button on the steering wheel. Once the call has ended, press the button on the steering wheel. NOTE: T o reject a call when the ring tone is heard, press the button on the steering wheel.
4-108 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2582 PHONE SETTINGS Call . (a name) If there are entries stored in the Phone Book, a number associated with a name and location can be dialed. See “Phone book registration” in this section to learn how to store entries.
phonebook. When the system acknowl- edges the command, the system announces all voicetags registered in the system. Playback of the list can be stopped at any time by pressing a button on the steering wheel.
4-110 Monitor, heater, air conditioner, audio, phone and voice recognition systems . Callback Use the Callback command to dial the last incoming call. . Help The system announces the available com- mands. SAA2585 Connect Phone . Add Phone Use the Pair Phone command to connect a compatible phone to the Bluetooth ® Hands- Free Phone System.
system asks the user to confirm. NOTE: When the user deletes a phone, the associated phone book for that phone will also be deleted. . Replace Phone Use the Replace Phone command to change the priority level of the active phone. The priority level determines which phone is active when more than one paired Blue- tooth ® phone is in the vehicle.
4-112 Monitor, heater, air conditioner, audio, phone and voice recognition systems . The ignition switch is placed in the OFF or L OCK position. NISSAN Voice Recognition allows hands-free operation of the Phone, Navigation, Information and Audio systems in one of two modes, Standard Mode or Alternate Command Mode.
SAA2529 Activating Standard Mode When the Alternate Command Mode is active, perform the following steps to switch to the Standard Mode. 1. Push the SETTING button on the instrument panel. 2. Select the “Others” key. 3. Select the “Voice Recognition” key.
4-114 Monitor, heater, air conditioner, audio, phone and voice recognition systems . Let’s Practice Mode that allows practicing by following the instructions of the system voice. . Using the Address Book T utorial for entering a destination by using the Address Book.
SAA2533 Useful tips for correct operation Y ou can display useful speaking tips to help the system recognize your voice commands cor- rectly. Select “Help on Speaking” to start display.
4-116 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2535 2. A list of commands appears on the screen, and the system announces, “Would you like to access Phone, Navigation, Information, Audio or Help?”. 3. After the tone sounds and the icon on the screen changes from to , speak a command.
“zero” for the number “0 (zero)”, “oh” for the letter “o (oh)”. Send digits using dial tone: . Press the T ALK switch during a phone call. . The menu will be launched and you will be provided with the following guidance: "Please say the digits to dial".
4-118 Monitor, heater, air conditioner, audio, phone and voice recognition systems Command List Category Command: Command Action Phone Operates the Phone function Navigation Operates the Navigation function Information Displays the vehicle Information function Audio Operates the Audio function.
. Information Command: Command Action Fuel Economy Displays fuel economy information. Maintenance Displays maintenance information. T raffic Information T urns the traffic information system ON and OFF. Where am I? Displays your current location. . Audio Command: Command Action AM T urns to the AM band, selecting the station last played.
4-120 Monitor, heater, air conditioner, audio, phone and voice recognition systems V oice command examples T o use the NISSAN Voice Recognition function, speaking one command is sometimes sufficient, but at other times it is necessary to speak two or more commands.
JVH0481X 4. Speak “Dial Number”. SAA2537 5. Speak “8 0 0” . Selecting the “Manual Controls” key switches the screen to the keypad to input the phone number manually. SAA2538 6. The system announces, “Please say the next three digits or dial, or say change number.
4-122 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2539 8. The system announces, “Please say the last four digits” or say change number. 9. Speak “ 6200 ” . SAA2540 10. The system announces, “Dial or Change Number?” 11.
SAA1859 Example 2 - Placing an international call to the phone number 011-81-111-222-3333: 1. Push the T ALK switch located on the steering wheel. SAA2535 2. The system announces, “Would you like to access Phone, Navigation, Information or Help?” 3.
4-124 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2541 5. Speak “011811112223333”. SAA2542 6. Speak “Dial”. 7. System makes a call to 011-81-111-222- 3333. NOTE: Any digit input format is available in the International Number input process.
SAA2529 Activating Alternate Command Mode When the Standard Mode is active, perform the following steps to switch to the Alternate Command Mode. 1. Push the SETTING button on the instrument panel. 2. Highlight the “Others” key. 3. Highlight the “Voice Recognition” key.
4-126 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2545 5. Select a category from the list. JVH0483X 6. Select an item. 7. If necessary, scroll the screen using the multi-function controller to view the entire list. 8.
Command List The words in italics are variable. Phone Commands: Command Action Dial Number Makes a call to a spoken phone number. Quick Dial Makes a call to a contact that is stored in the Quick Dial. Phonebook Makes a call to a contact that is stored in the mobile phone.
4-128 Monitor, heater, air conditioner, audio, phone and voice recognition systems Navigation Commands: Command Action Destination Home Sets a route to your home that is stored in the Address Book. Address Searches for a location by the street address specified, and sets a route to the location.
Information Commands: Command Action Fuel Economy Displays fuel economy information. Maintenance Displays maintenance information. Where am I? Displays your current location. T raffic Information T urns the traffic information system ON and OFF. Weather Information Displays weather information.
4-130 Monitor, heater, air conditioner, audio, phone and voice recognition systems Audio Commands: Command Action CD Starts to play a CD. FM T urns to the FM band, selecting the station last played. AM T urns to the AM band, selecting the station last played.
Help Commands: Command Action Command List Navigation Commands Displays the navigation command list. Phone Commands Displays the phone command list. Audio Commands Displays the audio command list. Information Commands Displays the information command list.
4-132 Monitor, heater, air conditioner, audio, phone and voice recognition systems General Commands: Command Action Go back Corrects the last recognition result to return to the previous screen Exit C.
SAA2547 Displaying user guide Y ou can confirm how to use voice commands by accessing a simplified User Guide, which contains basic instructions and tutorials for several voice commands. 1. Push the INFO button on the instrument panel. 2. Select the “Others” key using the multi- function controller and push the ENTER button.
4-134 Monitor, heater, air conditioner, audio, phone and voice recognition systems . Speak in a natural voice without pausing between words. SAA1859 Giving voice command 1. Push and release the T ALK switch located on the steering wheel. SAA2548 2. A list of commands appears on the screen, and the system announces, “Please say a command” .
Repeat the command in a clear voice. . Push the BACK button once to return to the previous screen. . If you want to cancel the command, push and hold the T ALK switch for 1 second.
4-136 Monitor, heater, air conditioner, audio, phone and voice recognition systems SAA2550 4. Select the user whose voice is memorized by the system. 5. Select the “Start Speaker Adaptation Learn- ing” key. SAA2551 6. Select a category to be learned by the system from the following list.
SAA2553 Speaker Adaptation function settings: Edit User Name Edit the user name using the keypad displayed on the screen. Delete Voice Data Resets the user’s voice that the voice recogni- tion system has learned.
4-138 Monitor, heater, air conditioner, audio, phone and voice recognition systems TROUBLESHOO TING GUIDE The system should respond correctly to all voice commands without difficulty . If problems are encountered, follow the solutions given in this guide for the appropriate error.
5 Starting and driving Precautions when starting and driving ................................ 5-3 Exhaust gas (carbon monoxide) ...................................... 5-3 Three-way catalyst .............................................................
Brake system ........................................................................... 5-37 Braking precautions ......................................................... 5-37 Parking brake break-in ...................................................
WARNING . Do not leave children or adults who would normally require the support of others alone in your vehicle. Pets should not be left alone either. They could accidentally injure themselves or others through inadvertent op- eration of the vehicle.
5-4 Starting and driving — Y ou notice a change in the sound of the exhaust system. — Y ou have had an accident invol- ving damage to the exhaust system, underbody, or rear of the vehicle. THREE-W A Y CA T AL YST The three-way catalyst is an emission control device installed in the exhaust system.
pressure telltale. Y our vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
5-6 Starting and driving tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If the light still illuminates while driving after adjusting the tire pressure, a tire may be flat. If you have a flat tire, replace it with a spare tire as soon as possible.
For Canada: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interfer- ence, including interference that may cause undesired operation of the device.
5-8 Starting and driving speed is reduced. Do not attempt to drive the vehicle back onto the road surface until vehicle speed is reduced. 6. When it is safe to do so, gradually turn the steering wheel until both tires return to the road surface. When all tires are on the road surface, steer the vehicle to stay in the appropriate driving lane.
you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol-related accidents. Although the local laws vary on what is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol.
5-10 Starting and driving your vehicle to roll over. . Do not grip the inside or spokes of the steering wheel when driving off- road. The steering wheel could move suddenly and injure your hands. Instead drive with your fin- gers and thumbs on the outside of the rim.
. Spinning the front wheels on slip- pery surfaces may cause the AWD warning light to flash and the AWD system to automatically switch from the AWD mode to the 2WD mode.
5-12 Starting and driving SSD0436 Operating range for engine start function The Intelligent Key functions can only be used for starting the engine when the Intelligent K ey is within the specified operating range * 1 .
until the shift lever is moved to the P (Park) position. When the ignition switch cannot be pushed toward the LOCK position, proceed as follows: 1. Move the shift lever into the P (Park) position. 2. Push the ignition switch to the OFF position. (The ignition switch position indicator will not illuminate.
5-14 Starting and driving SSD0837 INTELLIGENT KEY BA TTER Y DIS- CHARGE If the battery of the Intelligent Key is almost discharged, the guide light * B of the key port * A blinks and the indicator appears on the dot matrix liquid crystal display. (See “Dot matrix liquid crystal display” in the “2.
1. Apply the parking brake. 2. Move the shift lever to the P (Park) or N (Neutral) position. (P is recommended.) The starter is designed not to operate unless the shift lever is in either of the above positions. 3. Push the ignition switch to the ON position.
5-16 Starting and driving CONTINUOUSL Y VARIABLE TRANS- MISSION (CVT) The Continuously V ariable T ransmission (CVT) in your vehicle is electronically controlled to produce maximum power and smooth operation. The recommended operating procedures for this transmission are shown on the following pages.
SSD0691 T o move the shift lever, : Push the button * A while depressing the brake pedal. : Push the button * A . : Just move the shift lever. Shifting After starting the engine, fully depress the brake pedal, push the shift lever button and move the shift lever from the P (Park) position to any of the desired shift positions.
5-18 Starting and driving SSD0692 Overdrive (O/D) OFF switch When the O/D OFF switch is pushed with the shift lever in the D (Drive) position, the indicator light in the instrument panel illuminates. Use the overdrive off mode when you need improved engine braking.
SSD0693 Shift lock release If the battery charge is low or discharged, the shift lever may not be moved from the P (Park) position even with the brake pedal depressed and the shift lever button pushed. T o move the shift lever, perform the following procedure: 1.
5-20 Starting and driving SP A2331 T o apply: Fully depress the parking brake pedal * 1 . T o release: 1. Firmly apply the foot brake * 2 . 2. Depress the parking brake pedal * 1 and the parking brake will be released. 3. Before driving, be sure the brake warning light goes out.
system. . The LDW system is only a warning device to help inform the driver of a potential unintended lane depar- ture. It will not steer the vehicle or prevent loss of control. It is the driver’s responsibility to stay alert, drive safely, keep the vehicle in the traveling lane, and be in control of the vehicle at all times.
5-22 Starting and driving BSW SY STEM OPERA TION The BSW system operates above approximately 20 MPH (32 km/h) . When the camera unit detects vehicles in the detection zone, the Blind Spot Indicator light located inside the outside mirrors will illuminate.
JVS0159X SSD0885 Example Perform the following steps to enable or disable the BSW system. 1. Push the SETTING * 1 button and highlight the “Driver Assistance” key on the display using the multi-function controller. Then push the ENTER * 2 button. JVH0345X 2.
5-24 Starting and driving SSD1156 Warning systems switch The warning systems switch is used to tem- porarily turn off the warning systems (Lane Departure Warning (LDW) and Blind Spot Warning (BSW) systems) that are activated using the settings menu. WARNING .
SSD1026 BSW DRIVING SITUA TIONS Another vehicle approaching from be- hind The Blind Spot Indicator light illuminates if a vehicle enters the detection zone from behind in an adjacent lane.
5-26 Starting and driving SSD1034 If the driver activates the turn signal while another vehicle is in the detection zone, then the Blind Spot Indicator light flashes and a chime will sound twice. JVS0154X SSD0672 LDW light (orange, green) LDW SY STEM OPERA TION The LDW system operates above approximately 43 MPH (70 km/h) .
T urning on or off the LDW system The LDW system is turned on or off using the setting menu on the center display. S YSTEM ON: The LDW light (green) on the instrument panel will light up. S YSTEM OFF: The LDW light (green) on the instrument panel will go out.
5-28 Starting and driving JVH0345X 2. Highlight the “Lane Departure Warning” key , select ON (enabled) or OFF (disabled) and push the ENTER * 2 button.
of the curve. BSW/LDW TEMPORARY DISABLED ST A TUS When the lift gate is open and/or the low washer fluid is detected, the BSW and/or LDW system is turned off temporarily. The BSW light (green) and/or the LDW light (green) will blink, and either of the following message will appear on the dot matrix liquid crystal display: .
5-30 Starting and driving PRECAUTIONS ON CRUISE CON- TROL . If the cruise control system malfunctions, it will cancel automatically. The CRUISE in- dicator light on the meter panel will then blink to warn the driver. . If the engine coolant temperature becomes excessively high, the cruise control system will cancel automatically.
accelerator pedal. Y our vehicle will maintain the set speed. . T o pass another vehicle, depress the accelerator pedal. When you release the pedal, the vehicle will return to the previously set speed. . The vehicle may not maintain the set speed on winding or hilly roads.
5-32 Starting and driving Follow these easy-to-use Fuel Efficient Driving Tips to help you achieve the most fuel economy from your vehicle. 1. Use smooth accelerator and brake pedal application. . Avoid rapid starts and stops. . Use smooth, gentle accelerator and brake application whenever possible.
. Keep your engine tuned up. . Follow the recommended scheduled main- tenance. . Keep the tires inflated to the correct pressure. Low tire pressure increases tire wear and lowers fuel economy. . Keep the wheels in correct alignment. Improper alignment increases tire wear and lowers fuel economy.
5-34 Starting and driving L OCK mode The AWD LOCK indicator light will illuminate. AUT O mode The AWD LOCK indicator light will turn off. AWD mode Wheel driven AWD L OCK indica- tor light Use condi- t.
SSD0336B A WD W ARNING LIGHT The AWD warning light is located in the meter. The AWD warning light illuminates when the ignition switch is pushed to the ON position. It turns off soon after the engine is started. If any malfunction occurs in the A WD system while the engine is running, the warning light will come on.
5-36 Starting and driving SSD0488 WARNING . Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. . Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) .
WARNING If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be harder to operate. The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. If the engine stops or the drive belt breaks, you will still have control of the vehicle.
5-38 Starting and driving ANTI-L OCK BRAKING SY STEM (ABS) WARNING . The Anti-lock Braking System (ABS) is a sophisticated device, but it cannot prevent accidents resulting from careless or dangerous driving techniques. It can help maintain vehicle control during braking on slippery surfaces.
Normal operation The ABS operates at speeds above 3 to 6 MPH (5 to 10 km/h) . The speed varies according to road conditions. When the ABS senses that one or more wheels are close to locking up, the actuator rapidly applies and releases hydraulic pressure.
5-40 Starting and driving that tests the system each time you start the engine and move the vehicle forward or in reverse at a slow speed. When the self-test occurs, you may hear a “clunk” noise and/or feel a pulsation in the brake pedal. This is normal and is not an indication of a malfunction.
FREEING A FROZEN DOOR L OCK T o prevent a door lock from freezing, apply deicer through the key hole. If the lock becomes frozen, heat the key before inserting it into the key hole or use the remote keyless entry keyfob.
5-42 Starting and driving . Allow more stopping distance under these conditions. Braking should be started sooner than on dry pave- ment. . Allow greater following distances on slippery roads. . Watch for slippery spots (glare ice) . These may appear on an otherwise clear road in shaded areas.
MEMO Starting and driving 5-43.
5-44 Starting and driving MEMO.
6 In case of emergency Hazard warning flasher switch .............................................. 6-2 Emergency engine shut off ..................................................... 6-2 Flat tire .....................................................
6-2 In case of emergency SIC2574 Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights will flash. WARNING . If stopping for an emergency, be sure to move the vehicle well off the road.
TIRE PRESSURE MONIT ORING SY S- TEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pressure of all tires except the spare.
6-4 In case of emergency CHANGING A FLA T TIRE (Hardtop models) If you have a flat tire, follow the instructions below . Stopping the vehicle 1. Safely move the vehicle off the road and away from traffic. 2. T urn on the hazard warning flashers. 3. Park on a level surface and apply the parking brake.
Getting the spare tire and tools 1. Open the lift gate. 2. Remove the cargo cover (if so equipped) . (See “Cargo cover (if so equipped for Hardtop models)” in the “2. Instruments and controls” section.) 3. Open the cargo floor board. (See “Cargo floor box (if so equipped for Hardtop models)” in the “2.
6-6 In case of emergency SCE0853 T ype B 5. T ype B: Open the cargo floor board. SCE0716 Jacking tools 6. Remove the jacking tools and the spare tire. Jacking tools: Remove the jack by turning it, then remove the other tools. SCE0700 Spare tire (if so equipped) Spare tire: T urn the clamp to remove the tire.
SCE0630 Removing wheel cover (if so equipped) WARNING Never use your hands to remove the wheel cover. This may cause personal injury. T o remove the wheel cover, use the jack rod * 1 as illustrated. Apply cloth * 2 between the wheel and jack rod to prevent damaging the wheel and wheel cover.
6-8 In case of emergency SCE0572 Jack-up point 1. Place the jack directly under the jack -up point as illustrated so the top of the jack contacts the vehicle at the jack-up point. Align the jack head between the two notches in the front or the rear as shown.
JVE0028X Installing the spare tire The spare tire is designed for emergency use. (See specific instructions under the heading “ Wheels and tires” in the “8. Maintenance and do-it-yourself” section.) 1. Clean any mud or dirt from the surface between the wheel and hub.
6-10 In case of emergency accident or sudden stop. . The T-type spare tire and small size spare tire are designed for emer- gency use. See specific instructions under the heading “ Wheels and tires” in the “8. Maintenance and do-it-yourself” section.
— when the sealant has passed its expiration date (shown on the label attached to the bottle) — when the cut or the puncture is approximately 0.25 in (6 mm) or longer — when the tire sidewall is.
6-12 In case of emergency Before using emergency tire puncture repair kit . If any foreign object (for example, a screw or nail) is embedded in the tire, do not remove it. . Check the expiration date of the sealant (shown on the label attached to the bottle) .
SCE0868 2. T ake the hose * 1 and the power plug * 2 out of the air compressor. Remove the cap of the bottle holder from the air compressor. SCE0869 3. Remove the cap from the tire sealant bottle, and screw the bottle clockwise onto the bottle holder.
6-14 In case of emergency SCE0871 6. Push the ignition switch to the “ACC” position. Then turn the compressor switch to the ON ( − ) position and inflate the tire up to the pressure that is specified on the tire and loading information label affixed to the driver’s side center pillar if possible, or to the minimum of 180 kPa (26 psi) .
9. After driving, make sure that the air com- pressor switch is in the OFF position, then screw the hose securely onto the tire valve. Check the tire pressure with the pressure gauge. The temporary repair is completed if the tire pressure does not drop.
6-16 In case of emergency . Whenever working on or near a battery, always wear suitable eye protectors (for example, goggles or industrial safety spectacles) and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting.
5. Start the engine of the booster vehicle * B and let it run for a few minutes. 6. Keep the engine speed of the booster vehicle * B at about 2,000 rpm, and start the engine of the vehicle * A being jump started. CAUTION Do not keep the starter motor engaged for more than 10 seconds.
6-18 In case of emergency 3. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. (If steam or coolant is escaping, turn off the engine.) Do not open the hood further until no steam or coolant can be seen.
When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could damage your vehicle. T owing instructions are available from a NISSAN dealer. Local service operators are familiar with the applicable laws and procedures for towing.
6-20 In case of emergency SCE0439 All-Wheel Drive (AWD) models T OWING RECOMMENDED BY NISSAN All-Wheel Drive (AWD) models NISSAN recommends that towing dollies be used when towing your vehicle or place the vehicle on a flatbed truck as illustrated.
SCE0438 T wo-Wheel Drive (2WD) models T wo-Wheel Drive (2WD) models NISSAN recommends that your vehicle be towed with the driving (front) wheels off the ground or place the vehicle on a flat bed truck as illustrated. For All-Wheel Drive (AWD) models, see “ All- Wheel Drive (AWD) models” earlier in this section.
6-22 In case of emergency SCE0717 Front SCE0718 Tie down and recovery hook VEHICLE RECOVERY (freeing a stuck vehicle) WARNING . Stand clear of a stuck vehicle. . Do not spin your tires at high speed. This could cause them to explode and result in serious injury.
. Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recov- ery. Rocking a stuck vehicle If your vehicle is stuck in sand, snow, mud, etc., use the following procedure: 1. T urn off the Vehicle Dynamic Control (VDC) system.
6-24 In case of emergency MEMO.
7 Appearance and care Cleaning exterior ....................................................................... 7-2 Washing ................................................................................. 7-2 Soft top care and cleaning (CrossCabriolet models) .
7-2 Appearance and care In order to maintain the appearance of your vehicle, it is important to take proper care of it. T o protect the paint surface, wash your vehicle as soon as you can: . after a rainfall to prevent possible damage from acid rain .
SOFT T OP CARE AND CLEANING (CrossCabriolet models) Proper care and handling should be observed to maintain a good appearance of the soft top. Improper care may cause the top cloth’s surface to stiffen, stain, or mat. Follow the instructions shown in this section.
7-4 Appearance and care CAUTION . When cleaning the inside of the windows, do not use sharp-edged tools, abrasive cleaners or chlorine- based disinfectant cleaners. They could damage the electrical conduc- tors, radio antenna elements or rear window defroster elements.
Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dam- pened in mild soap solution, then wipe clean with a dry soft cloth.
7-6 Appearance and care tion. . Properly position the mats in the floorwell using the floor mat posi- tioning aid. See “Floor mat posi- tioning aid” later in this section. The use of genuine NISSAN floor mats can extend the life of your vehicle carpet and make it easier to clean the interior.
MOST COMMO N F ACT ORS CONTRI- BUTING T O VEHICLE CORROSION . The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas. . Damage to paint and other protective coat- ings caused by gravel and stone chips or minor traffic accidents.
7-8 Appearance and care MEMO.
8 Maintenance and do-it-yourself Maintenance requirement ........................................................ 8-2 Scheduled maintenance .................................................... 8-2 General maintenance ..................................
8-2 Maintenance and do-it-yourself Some day-to-day and regular maintenance is essential to maintain your vehicle’s fine mechan- ical condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed.
Lights*: Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts (lug nuts)*: When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts.
8-4 Maintenance and do-it-yourself Windshield defroster: Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Windshield wiper and washer*: Check that the wipers and washer operate properly and that the wipers do not streak.
When performing any inspection or mainte- nance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle.
8-6 Maintenance and do-it-yourself difficulties or excessive emissions, and could affect warranty coverage. If in doubt about any servicing, we recommend that it be done by a NISSAN dealer. SDI2172 VQ35DE ENGINE 1. Power steering fluid reservoir 2. Drive belt location 3.
The engine cooling system is filled at the factory with a pre-diluted mixture of 50% Genuine NISSAN Long Life Antifreeze/Coolant (blue) and 50% water to provide year-round anti-freeze and coolant protection. The antifreeze solution contains rust and corrosion inhibitors.
8-8 Maintenance and do-it-yourself SDI2173 CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir when the engine is cold. If the coolant level is below the MIN level * 2 , open the reservoir cap and add coolant up to the MAX level * 1 .
opening. Do not overfill * 3 . 6. Recheck oil level with the dipstick. It is normal to add some oil between oil maintenance intervals or during the break- in period, depending on the severity of operating conditions. CAUTION Oil level should be checked regularly.
8-10 Maintenance and do-it-yourself SDI2355 Engine oil and filter 1. Place a large drain pan under the drain plug * A . 2. Remove the oil filler cap * B . 3. Remove the drain plug with a wrench and completely drain the oil. CAUTION Be careful not to burn yourself, as the engine oil is hot.
Correct as required. 13. T urn the engine off and wait more than 10 minutes. Check the oil level with the dipstick. Add engine oil if necessary. After the operation 1. Lower the vehicle carefully to the ground. 2. Dispose of waste oil and filter properly.
8-12 Maintenance and do-it-yourself CAUTION . Do not overfill. . Use Genuine NISSAN PSF or equivalent. For additional brake fluid information, see “Capacities and recommended fuel/lubricants” in the “9. T echnical and consumer information” section of this manual.
SDI2179 Fill the window washer fluid reservoir periodi- cally . Add window washer fluid when the low window washer fluid warning appears on the dot matrix liquid crystal display. T o fill the window washer fluid reservoir, lift the cap and pour the window washer fluid into the reservoir opening.
8-14 Maintenance and do-it-yourself contact your skin, eyes, fabrics, or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 minutes and seek medical attention.
JUMP ST ARTING If jump starting is necessary, see “Jump starting” in the “6. In case of emergency” section. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer. CAUTION . Do not ground accessories directly to the battery terminal.
8-16 Maintenance and do-it-yourself in poor condition or loose, have it replaced or adjusted by a NISSAN dealer. 2. Have the belt condition checked regularly. WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely.
SDI2180 Pull the tabs * 1 and pull out the cover * 2 . The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance log shown in the “NISSAN Service and Main- tenance Guide”. When replacing the filter, wipe the inside of the air cleaner housing and the cover with a damp cloth.
8-18 Maintenance and do-it-yourself CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent.
SDI2199 Be careful not to clog the washer nozzle * A . This may cause improper windshield washer operation. If the nozzle is clogged, remove any objects with a needle or small pin * B .B e careful not to damage the nozzle. Contact a NISSAN dealer if checking or replacement is required.
8-20 Maintenance and do-it-yourself light to moderate stops is normal and does not affect the function or performance of the brake system. Proper brake inspection intervals should be followed. For additional information, see the maintenance log section of your “NISSAN Service and Maintenance Guide”.
SDI1754 5. If the fuse is open * A , replace it with a new fuse * B . Spare fuses are stored in the passenger compartment fuse box. 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer. Fusible links If any electrical equipment does not operate and fuses are in good condition, check the fusible links.
8-22 Maintenance and do-it-yourself SDI2704 Example Extended storage fuse switch T o reduce battery drain, the extended storage fuse switch comes from the factory switched off. Prior to delivery of your vehicle, the switch is pushed in (switched on) and should always remain on.
SDI2451 Replace the battery as follows: 1. Remove the mechanical key from the key. 2. Insert a small screwdriver into the slit of the corner and twist it to separate the upper part from the lower part. Use a cloth to protect the casing. 3. Replace the battery with a new one.
8-24 Maintenance and do-it-yourself may cause undesired operation. Note: Changes or modifications not ex- pressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For Canada: This device complies with RSS-210 of Industry Canada.
JVM0092X HARDT OP MODELS 1. Front turn signal/parking light* or Front turn signal light** 2. Headlight (high-beam)* or Front parking light** 3. Headlight (low-beam)* or Headlight (low-beam, high-beam)** 4. Side marker light 5. Front map light 6. Rear personal light 7.
8-26 Maintenance and do-it-yourself SDI2723 CROSSCABRIOLET MODELS 1. Front turn signal light 2. Front parking light 3. Headlight (low-beam, high-beam) 4. Front side marker light 5. Front map light 6. Front fog light 7. Step light 8. High-mounted stop light 9.
HEADLIGHTS Fog may temporarily form inside the lens of the exterior lights in the rain or in a car wash. A temperature difference between the inside and the outside of the lens causes the fog. This is not a malfunction. If large drops of water collect inside the lens, contact a NISSAN dealer.
8-28 Maintenance and do-it-yourself * B Low-beam bulb.
EXTERIOR AND INTERIOR LIGHTS Item Wattage (W) Bulb No. Headlight High/Low beams (Xenon)* 35 D2S High beam (Halogen) (Hardtop) 65 HB3 Low beam (Halogen) (Hardtop) 55 H11 Front turn signal/parking light.
8-30 Maintenance and do-it-yourself Replacement procedure s All other lights are either type A , B, C, D, E or F . When replacing a bulb, first remove the lens and/or cover. SDI1679 SDI2200 Side marker light (Halogen headlight model) 1. Remove the rubber cover.
SDI2184 Front fog light (if so equipped) SDI2030 Front map light SDI2031 Rear personal light (if so equipped) SDI1500B Cargo light (Hardtop models) SDI1451B T runk light (CrossCabriol et models) Maint.
8-32 Maintenance and do-it-yourself SDI2032 V anity mirror light (if so equipped) If you have a flat tire, see “Flat tire” in the “6. In case of emergency” section. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) .
WARNING . Improperly inflated tires can fail suddenly and cause an accident. . The Gross Vehicle Weight rating (GVWR) is located on the F.M.V. S.S./C .M.V.S.S. certification la- bel. The vehicle weight capacity is indicated on the Tire and Loading Information label.
8-34 Maintenance and do-it-yourself SDI2503 Tire and Loading Information label * 1 Seating capacity: The maximum num- ber of occupants that can be seated in the vehicle. * 2 V ehicle load limit: See “Vehicle load- ing information” in the “9. T echnical and consumer information” section.
SDI1949 Checking the tire pressure 1. Remove the valve stem cap from the tire. 2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem sideways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage.
8-36 Maintenance and do-it-yourself CrossCabriolet models: SIZE COLD TIRE INFLA TION PRES- SURE FRONT ORIGINAL TIRE P235/55R20 102T 230 kPa, 33 PSI REAR ORIGINAL TIRE P235/55R20 102T 230 kPa, 33 PSI SDI1575 Example TIRE LABELING Federal law requires tire manufacturers to place standardized information on the side- wall of all tires.
6. T wo- or three-digit number (94): This number is the tire’s load index. It is a measurement of how much weight each tire can support. Y ou may not find this information on all tires because it is not required by law. 7. H: Tire speed rating. Y ou should not drive the vehicle faster than the tire speed rating.
8-38 Maintenance and do-it-yourself * 6 T erm of “tubeless” or “tube type” Indicates whether the tire requires an inner tube (“tube type”) or not (“tube- less”) . * 7 The word “radial” The word “radial” is shown, if the tire has radial structure.
match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tires may be used.
8-40 Maintenance and do-it-yourself SDI1662 CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km) . (See “Flat tire” in the “6. In case of emergency” section for tire replacing procedures.) As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.
. The original tires have built-in tread wear indicators. When wear indicators are visible, the tire(s) should be replaced. . Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician, because some tire damage may not be obvious.
8-42 Maintenance and do-it-yourself TPMS. . Do not install a damaged or de- formed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warning. . The use of retread tire is not re- commended.
pressure for standard tires, as in- dicated on the Tire and Loading Information label. . With the TEMPORAR Y USE ONL Y spare tire installed do not drive your vehicle at speeds faster than 50 MPH (80 km/h) .
8-44 Maintenance and do-it-yourself MEMO.
9 T echnical and consumer information Capacities and recommended fuel/lubricants ................... 9-2 Fuel recommendation ......................................................... 9-3 Engine oil and oil filter recommendation .......................
9-2 T echnical and consumer information The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure instructed in the “8. Maintenance and do-it-yourself” section to determine the proper refill capacity.
FUEL RECOMMEND A TION Hardtop models Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91) . CrossCabriolet models NISSAN recommends the use of unleaded premium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Re- search octane number 96) .
9-4 T echnical and consumer information . E-15 fuel contains more than 10% oxygenate. E-15 fuel will adversely affect the emission control devices and systems of the vehicle and should not be used. Damage caused by such fuel is not covered by the NISSAN new vehicle limited warranty.
JVT0159X 1. API certification mark 2. API service symbol ENGINE OIL AND OIL FIL TER RE- COMMENDA TION Selecting the correct oil It is essential to choose the correct grade, quality , and viscosity engine oil to ensure satisfactory engine life and performance, see “Capacities and recommended fuel/lubricants” earlier in this section.
9-6 T echnical and consumer information interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes. . repeated short distance driving at cold outside temperatures .
ENGINE Model VQ35DE T ype Gasoline, 4-cycle Cylinder arrangement 6-cylinder, V-slanted at 60 8 Bore 6 Stroke in (mm) 3.760 6 3.205 (95.5 6 81.4) Displacement cu in (cm 3 ) 213.45 (3,498) Firing order 1-2-3-4-5-6 Idle speed rpm No adjustment is necessary.
9-8 T echnical and consumer information DIMENSIONS AND WEIGHTS Overall length in (mm) 189.9 (4,822)*1 190.1 (4,828)*2 Overall width in (mm) 74.1 (1,883)*1 74.5 (1,893)*2 Overall height in (mm) 67.0 (1,703)*1 68.0 (1,728)*1, *3 66.2 (1,681)*2 Front tread in (mm) 63.
STI0374 VEHICLE IDENTIFICA TION NUMBER (chassis number) The vehicle identification number is located as shown. Remove the cover to access the number. STI0562 ENGINE SERIAL NUMBER The number is stamped on the engine as shown.
9-10 T echnical and consumer information F .M.V .S.S./C.M.V .S.S. CERTIFICA TION LABEL The Federal/Canadian Motor Vehicle Safety Standards (F .M.V .S.S.
STI0339 AIR CONDITIONER SPECIFICA TION LABEL The air conditioner specification label is at- tached as shown. T echnical and consumer information 9-11.
9-12 T echnical and consumer information STI0821 Use the following steps to mount the license plate: Before mounting the license plate, confirm that the following parts are enclosed in the plastic bag. . License plate bracket . Screw 6 2 1. Park the vehicle on flat, level ground.
WARNING . It is extremely dangerous to ride in a cargo area inside the vehi- cle. In a collision, people riding in these areas are more likely to be seriously injured or killed. . Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
9-14 T echnical and consumer information STI0445 Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the avail- able cargo and luggage load capacity of your vehicle.
9-16 T echnical and consumer information L OADING TIPS . The GVW must not exceed GVWR or GA WR as specified on the F .M.V .S.S./ C.M.V .S.S. certification label. . Do not load the front and rear axle to the GAWR. Doing so will exceed the GVWR. WARNING .
guide includes information on trailer towing capability and the special equipment required for proper towing. CrossCabriolet models: Do not tow a trailer with your vehicle. MAXIMUM LOAD LIMITS Maximum trailer loads Never allow the total trailer load to exceed the value specified in the “T owing Load/Specifica- tion” chart.
9-18 T echnical and consumer information CAUTION Vehicle damage resulting from impro- per towing procedures are not covered by NISSAN warranties. STI0542 T ongue load When using a weight carrying or a.
required to achieve the rating. Additional pas- sengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load.
9-20 T echnical and consumer information Always verify that available capacities are within the required ratings..
T OWING L OAD/SPECIF ICA TION T OWING L OAD/SPECIFICATION CHART Unit: lb (kg) MODEL VQ35DE WEIGHT CVT MAXIMUM TRAILER WEIGHT*1 3,500 (1,588) MAXIMUM TONGUE L OAD 350 (159) GROSS COMBINED WEIGHT RA TING 8,300 (3,765) RECOMMENDED EQUIPMENT*2 Sway Control Device (SCD) 1: All towing above 1,000 lb (454 kg) requires the use of trailer brakes.
9-22 T echnical and consumer information . Choose the proper class hitch ball based on the trailer weight. . The diameter of the threaded shank of the hitch ball must be matched to the ball mount hole diameter. The hitch ball shank should be no more than 1/16´´ smaller than the hole in the ball mount.
turning corners. T railer lights CAUTION When splicing into the vehicle electrical system, a commercially available power-type module/converter must be used to provide power for all trailer lighting.
9-24 T echnical and consumer information . Do not use the Lane Departure W arning (LDW) system (if so equipped) . . Always drive your vehicle at a moderate speed. Some states or provinces have specific speed limits for vehicles that are towing trailers.
vehicle. . Do not correct trailer sway by steering or applying the brakes. 2. When the trailer sway stops, gently apply the brakes and pull to the side of the road in a safe area. 3. T ry to rearrange the trailer load so it is balanced as described earlier in this section.
9-26 T echnical and consumer information NISSAN” in the “6. In case of emergency” section of this manual. Continuously Variable T ransmiss ion (CVT) All-Wheel Drive (AWD) models: Do not tow an AWD vehicle with any of the wheels on the ground.
WARNING The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combi- nation, can cause heat build-up and possible tire failure.
9-28 T echnical and consumer information For Canada If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform T ransport Canada in addition to notifying NISSAN.
the I/M test, check the vehicle’s inspection/ maintenance test readiness condition. Place the ignition switch in the ON position without starting the engine. If the Malfunction Indicator Light (MIL) comes on steady for 20 seconds and then blinks for 10 seconds, the I/M test condition is “not ready”.
9-30 T echnical and consumer information Genuine NISSAN Service Manuals for this model year and prior can be purchased. A genuine NISSAN Service Manual is the best source of service and repair information for your vehicle. This manual is the same one used by the factory trained technicians working at NISSAN dealerships.
10 Index A ABS (Anti-lock Braking System) ............................ 5-38 Advanced air bag system ......................................... 1-52 Air bag system Advanced air bag system .................................. 1-52 Door-mounted curtain side-impact and rollover supplemental air bag system .
10-2 Compact Disc (CD) changer (See audio system)................................................. .............. 4-62 Compact Disc (CD) player (See audio system)................................................. .............. 4-67 Compass ...........
Fuel Capacities and recommended fuel/lubricants............................... 9-2 Fuel economy........................................................ 5-33 Fuel economy information (display)................. 4-11 Fuel octane rating ..................
10-4 Fog light switch .................................................... 2-41 Headlight switch ................................................... 2-37 Headlights bulb replacement ............................ 8-27 Indicator lights ..................
Car phone or CB radio ...................................... 4-88 Power Front seat adjustment ............................................ 1-4 Power door lock ............................................ .......... 3-5 Power outlet ...................
10-6 Push starting ......................................................... 6-17 Starting the engine ....................................... ....... 5-15 ST A TUS button.............................................................. 4-9 Status light, Front passenger air bag .
V ehicle dynamic control (VDC) off switch ..... 2-44 V ehicle dynamic control (VDC) system.......... 5-39 V ehicle dynamic control (VDC) warning light .......................................................... 2-16 V ehicle information and settings (display) .
FUEL RECOMMEND A TION: Hardtop models Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91) . CrossCabriolet models NISSAN recommends the use of unleaded premium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Re- search octane number 96) .
® 2014 M U RAN O OWN E R’S MAN UAL For y our safety , read car efully and keep in this v ehicle. 2014 N I S SAN M U RAN O Z5 1-W Z5 1-W Printing : November 2012 (31) Publication No.
Een belangrijk punt na aankoop van elk apparaat Nissan Murano (2014) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Nissan Murano (2014) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Nissan Murano (2014) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Nissan Murano (2014) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Nissan Murano (2014) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Nissan Murano (2014) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Nissan Murano (2014) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Nissan Murano (2014) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
