Gebruiksaanwijzing /service van het product Sentra (2011) van de fabrikant Nissan
Ga naar pagina of 366
® 2011 S E NTRA OWN E R’S MAN UAL For y our safety , read car efully and keep in this v ehicle. 2011 N IS SAN SE NTRA B16-D Printing : April 2011 Publication No.
W elcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. This manual was prepared to help you under- stand the operation and maintenance of your vehicle so that you may enjoy many miles (kilome- ters) of driving pleasure.
MODIFICA TION OF Y OUR VEHICLE This vehicle should not be modified. Modification could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or per- formance problems resulting from modi- fications may not be covered under NISSAN warranties.
CALIFORNIA PROPOSITION 65 W ARNING WARNING Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth de- fects or other reproductive harm.
NISSAN CARE S... Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Y our satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Y our NISSAN dealer is always available to assist you with all your automobile sales and service needs.
T able of Contents Illustrated table of contents Safety—Seats, seat belts and supplemental restraint system Instruments and controls Pre-driving checks and adjustments Display screen, heater, air co.
I n f o r m a t i o n P r o v i d e d b y :.
0 Illustrated table of contents Air bags, seat belts and child restraints ..............0 - 2 Exterior front ......................................0 - 3 Exterior rear .......................................0 - 4 Passenger compartment .................
1. T op tether anchor (P . 1-26) 2. Rear head restraint (P . 1-5) 3. Rear seat belts (P . 1-11) 4. Roof-mounted curtain side-impact supplemental air bag (P . 1-41) 5. Front seat-mounted side-impact supplemental air bag (P . 1-41) 6. Front-seat Active Head Restraint (P .
1. Engine hood (P . 3-23) 2. Windshield wiper and washer switch (P . 2-20) 3. Windshield (P . 8-20) 4. Moonroof (if so equipped) (P . 2-37) 5. P ower windows (if so equipped) (P . 2-34) 6. Door locks, keyfob (if so equipped) , NISSAN Intelligent K ey ™ (if so equipped) , keys (P .
1. T runk lid (P .3-23 ) 2. V ehicle loading (P . 9-13) 3. Interior trunk lid release (P . 3-24) 4. Rear window defroster switch (P . 2-21) 5. Child safety locks (P . 3-7) 6. Fuel-filler door (P . 3-25) 7. Fuel-filler cap, fuel recommendation (P . 3-25, P .
1. Rear seat (P . 1-3) 2. Moonroof (if so equipped) (P . 2-37) 3. Interior lights, illuminated entry , moonroof switch (if so equipped) (P . 2-39, P . 2-21, P . 2-37) 4. Sun visors (P . 3-28) 5. Rearview mirror (P . 3-28) 6. Glove box (P . 2-31) 7. Cup holders (P .
1. Headlight/fog light (if so equipped) /turn signal switch (P . 2-21); Manual shift paddles (if so equipped) (P .5-15) 2. Steering wheel switch for audio control and Bluetooth 姞 Hands-Free Phone System (if so equipped) (P . 4-61, 4-63) 3. Driver’s supplemental air bag/Horn (P .
25. Tilt steering (P .3-27) 26. Storage bin (P . 2-28) 27. Hood release lever (P . 3-23) 28 V ehicle Dynamic Control (VDC) off switch (if so equipped) (P .2-16) * Refer to the separate Navigation System Own- er’s Manual (if so equipped) . See the page number indicated in paren- theses for operating details.
MR20DE engine 1. Engine coolant reservoir (P . 8-8) 2. Engine oil filler cap (P . 8-10) 3. Brake fluid reservoir/Clutch fluid reservoir (M/T model) (P . 8-14) 4. Battery (P . 8-15) 5. Air cleaner (P . 8-19) 6. Fuse/fusible link box (P . 8-22) 7. Radiator cap (P .
QR25DE engine 1. Engine coolant reservoir (P . 8-8) 2. Engine oil filler cap (P . 8-10) 3. Brake fluid reservoir/Clutch fluid reservoir (M/T model) (P . 8-14) 4. Battery (P . 8-15) 5. Air cleaner (P . 8-19) 6. Fuse/fusible link box (P . 8-22) 7. Radiator cap (P .
W arning light Name Page or Anti-lock Braking System (ABS) warn- ing light 2-10 or Brake warning light 2-10 Charge warning light 2-11 Door open warning light 2-11 Electric power steering warning light.
Indicator light Name Page Overdrive off indica- tor light (CVT mod- els) 2-15 Security indicator light 2-15 Side light and head- light indicator light (green) 2-16 Slip indicator light (if so equipped.
MEMO 0-12 Illustrated table of contents I n f o r m a t i o n P r o v i d e d b y :.
1 Safety—Seats, seat belts and supplemental restraint system Seats . ...........................................1 - 2 Front manual seat adjustment ....................1 - 2 Rear folding seat system (if so equipped) .........1 - 3 Head restraints ...
WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. Y ou could also slide under the lap belt and receive serious internal injuries.
Forward and backward Pull the center of the bar up and hold it while you slide the seat forward or backward to the desired position. Release the bar to lock the seat in position. Reclining T o recline the seatback, pull the lever up and lean back. T o bring the seatback forward, pull the lever up and lean your body forward.
Interior trunk access (if so equipped) The trunk can be accessed from the rear seat for loading and unloading, as shown. 1. Stow the outboard seat belts with the clip before folding the rear seatbacks. When folding the passenger’s side rear seatback, first disconnect and stow the cen- ter seat belt.
Folding the rear cushions and seatbacks (if so equipped) 1. Lift up on the front edge of the seat cushion and fold it toward the front of the vehicle. 2. Fold down the rear head restraint. Pull the head restraint forward and rotate until it clicks into the locked position 䊊 1 .
3. T o return the head restraint to the normal position, push down 䊊 1 and release, then rotate up until in position 䊊 2 . 4. Fold down seatbacks. See “Interior trunk access” earlier in this section. WARNING ● Never allow anyone to ride in the cargo area or on the rear seat when it is in the fold-down position.
Center armrest (if so equipped) Pull the armrest down until it is horizontal. HEAD RESTRAINTS WARNING Head restraints supplement the other ve- hicle safety systems. They may provide additional protection against injury in cer- tain rear end collisions.
Components 1. Head restraint 2. Adjustment notches 3. Lock knob 4. Stalks Adjustment Adjust the head restraint so the center is level with the center of the seat occupant’s ears.
T o lower, push and hold the lock knob and push the head restraint down. Removal Use the following procedure to remove the ad- justable head restraints. 1. Pull the head restraint up to the highest position. 2. Push and hold the lock knob. 3. Remove the head restraint from the seat.
Front-seat Active Head Restraints The Active Head Restraint moves forward utiliz- ing the force that the seatback receives from the occupant in a rear-end collision.
PRECAUTIONS ON SEA T BEL T USAGE If you are wearing your seat belt properly ad- justed and you are sitting upright and well back in your seat with both feet on the floor, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced.
WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly re- strained in the rear seat and, if appro- priate, in a child restraint. WARNING ● The seat belt should be properly ad- justed to a snug fit.
WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never put the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder. ● Position the lap belt as low and snug as possible AROUND THE HIPS, NO T THE WAIST .
PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug and always position the lap belt as low as possible around the hips, not the waist. Place the shoulder belt over your shoulder and across your chest.
䊊 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage. ● The retractor is designed to lock dur- ing a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat.
WARNING When fastening the seat belts, be certain that the seatbacks are completely se- cured in the latched position. If they are not completely secured, passengers may be injured in an accident or sudden stop. Unfastening the seat belts 䊊 1 T o unfasten the seat belt, press the button on the buckle.
Center of the rear seat (except SE-R model) The rear seat center seat belt has a connector tongue 䊊 1 and a seat belt tongue 䊊 2 . Both the connector tongue and the seat belt tongue must be securely latched for proper seat belt opera- tion. WARNING ● Always fasten the connector tongue and the seat belt in the order shown.
Stowing the rear center seat belt When folding down the rear seat, the center seat belt can be retracted into a stowed position as follows: 䊊 1 Hold the connector tongue so that the seat belt does not retract suddenly when the tongue is released from the connector buckle.
Attaching the rear center seat belt Always be sure the center seat belt connector tongue and connector buckle are attached. Dis- connect only when folding down the rear seat. T o connect the buckle: 䊊 1 Pull out the connector buckle from the fabric sleeve.
WARNING ● After adjustment, release the adjust- ment button and try to move the shoul- der belt anchor up and down to make sure it is securely fixed in position.
Children need adults to help protect them. They need to be properly restrained. In addition to the general information in this manual, child safety information is available from many other sources, including doctors, teachers, government traffic safety offices, and community organizations.
LARGER CHILDREN Children who are too large for child restraints should be seated and restrained by the seat belts which are provided. The seat belt may not fit properly if the child is less than 4 ft 9 in (142.5 cm) tall and weighs between 40 lbs (18 kg) and 80 lbs (36 kg) .
WARNING ● Failure to follow the warnings and in- structions for proper use and installa- tion of child restraints could result in serious injury or death of a child or other passengers in a sudden stop or collision: – The child restraint must be used and installed properly.
This vehicle is equipped with a universal child restraint anchor system, referred to as the LA T CH (Lower Anchors and T ethers for CHildren) sys- tem. Some child restraints include rigid or webbing-mounted attachments that can be con- nected to these anchors.
LA T CH lower anchor WARNING Failure to follow the warnings and instruc- tions for proper use and installation of child restraints could result in serious in- jury or death of a child or other passen- gers in a sudden stop or collision: – Attach LA TCH system compatible child restraints only at the locations shown in the illustration.
When installing a child restraint, carefully read and follow the instructions in this manual and those supplied with the child restraint. T op tether anchor point locations The child restraint top tether strap must be used when installing the child restraint with the LA T CH lower anchor attachments or seat belts.
2. Secure the child restraint anchor attach- ments to the LA T CH lower anchors. Check to make sure the LA T CH attachment is prop- erly attached to the lower anchors. 3. For child restraints that are equipped with webbing-mounted attachments, remove any additional slack from the anchor attach- ments.
4. After attaching the child restraint, test it be- fore you place the child in it. Push it from side to side while holding the child restraint near the LA T CH attachment path. The child re- straint should not move more than 1 inch (25 mm) , from side to side.
WARNING ● The three-point seat belt with Auto- matic Locking Retractor (ALR) must be used when installing a child restraint. Failure to use the ALR mode will result in the child restraint not being properly secured. The restraint could tip over or be loose and cause injury to a child in a sudden stop or collision.
3. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode) . It reverts to the Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted.
6. After attaching the child restraint, test it be- fore you place the child in it. Push it from side to side while holding the child restraint near the seat belt path. The child restraint should not move more than 1 inch (25 mm) , from side to side. T ry to tug it forward and check to see if the belt holds the restraint in place.
3. The back of the child restraint should be secured against the vehicle seatback. If necessary, adjust or remove the head re- straint to obtain the correct child restraint fit. If the head restraint is removed, store it in a secure place. Be sure to reinstall the head restraint when the child restraint is re- moved.
7. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 1 through 6. FORW ARD-F ACING CHILD RESTRAINT INST ALLA TION USING THE SEA T BEL TS WARNING The three-point seat belt with Automatic Locking Retractor (ALR) must be used when installing a child restraint.
3. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s in- structions for belt routing.
6. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt. 7. Tighten the tether strap according to the manufacturer’s instructions to remove any slack.
10. If the child restraint is installed in the front passenger seat, place the ignition switch in the ON position. The front passenger air bag status light or should illumi- nate. If this light is not illuminated, see ⬙ Front passenger air bag and status light ⬙ in this section.
2. If necessary, raise or remove the head re- straint to position the top tether strap over the top of the seatback. If the head restraint is removed, store it in a secure place. Be sure to reinstall the head restraint when the child restraint is removed.
Booster seats of various sizes are offered by several manufacturers. When selecting any booster seat, keep the following points in mind: ● Choose only a booster seat with a label certifying that it complies with Federal Motor V ehicle Safety Standard 213 or Canadian Motor V ehicle Safety Standard 213.
Booster seat installation CAUTION Do not use the lap/shoulder belt in the Automatic Locking Retractor mode when using a booster seat with the seat belts. Refer to all W arnings and Cautions in the “Child safety” , “Child restraints” and “Booster seats” sections before installing a child restraint.
If the seating position does not have an adjustable head restraint and it is interfering with the proper booster seat fit, try another seating position or a different booster seat. 4. Position the lap portion of the seat belt low and snug on the child’s hips.
PRECAUTIONS ON SUPPLEMENT AL RESTRAINT S Y STEM This Supplemental Restraint System (SRS) sec- tion contains important information concerning the following systems: ● Driver and passenger supplementa.
WARNING ● The front air bags ordinarily will not inflate in the event of a side impact, rear impact, rollover, or lower severity fron- tal collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.
WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.
ARS1042 ARS1043 ARS1044 1-44 Safety—Seats, seat belts and supplemental restraint system I n f o r m a t i o n P r o v i d e d b y :.
WARNING ● Children may be severely injured or killed when the front air bags, side air bags or curtain air bags inflate if they are not properly restrained.
WARNING ● The seat belts, the side air bags and curtain air bags are most effective when you are sitting well back and upright in the seat with both feet on the floor.
SSS0159 SSS0162 Safety—Seats, seat belts and supplemental restraint system 1-47 I n f o r m a t i o n P r o v i d e d b y :.
1. Roof-mounted curtain side-impact supplemental air bag 2. Front seat-mounted side-impact supplemental air bag modules 3. Supplemental front-impact air bag modules 4. Crash zone sensor 5. Air bag Control Unit (ACU) 6. Occupant classification sensor (pres- sure sensor) 7.
flate if the forces in another type of collision are similar to those of a higher severity frontal impact. They may not inflate in certain frontal collisions. V ehicle damage (or lack of it) is not always an indication of proper front air bag system opera- tion.
Front passenger air bag and status light WARNING The front passenger air bag is designed to automatically turn OFF under some con- ditions. Read this section carefully to learn how it operates. Proper use of the seat, seat belt and child restraints is nec- essary for most effective protection.
weight. It works together with seat belt sensors described later. For example, if a child is in the front passenger seat, the Advanced Air Bag Sys- tem is designed to turn the passenger air bag OFF in accordance with the regulations.
If the passenger air bag status light will not illu- minate even though you believe that the child restraint, the seat belts and the occupant are properly positioned, the system may be sensing an unoccupied seat (in which case the air bag is OFF) . Y our NISSAN dealer can check that the system is OFF by using a special tool.
● Work on and around the front air bag system should be done by a NISSAN dealer. Installation of electrical equip- ment should also be done by a NISSAN dealer.
practical from the door finishers and side roof rails. The side air bags and curtain air bags inflate quickly in order to help protect the front and rear outboard occupants.
● If the vehicle becomes involved in a collision but a pretensioner is not acti- vated, be sure to have the pretensioner system checked and, if necessary, re- placed by your NISSAN dealer. ● No unauthorized changes should be made to any components or wiring of the pretensioner system.
SUPPLEMENT AL AIR BAG W ARNING LIGHT The supplemental air bag warning light, displaying in the instrument panel, moni- tors the circuits for the air bag systems, preten- sioners and all related wiring.
WARNING ● Once a front air bag, side air bag, or curtain air bag has inflated, the air bag module will not function again and must be replaced. Additionally, the ac- tivated pretensioner must also be re- placed. The air bag module and preten- sioner should be replaced by a NISSAN dealer.
2 Instruments and controls Instrument panel ...................................2 - 2 Meters and gauges ................................2 - 3 Speedometer and odometer . . ...................2 - 4 T achometer ....................................2 - 5 g (gravity) -force gauge (if so equipped) .
Windows ........................................ 2-34 P ower windows (if so equipped) ................ 2-34 Manual windows (if so equipped) ................ 2-37 Moonroof (if so equipped) ......................... 2-37 Electric moonroof ..............
1. Headlight/fog light (if so equipped) /turn signal switch (P . 2-21); Manual shift paddles (if so equipped) (P .5-15) 2. Steering wheel switch for audio control and Bluetooth 姞 Hands-Free Phone System (if so equipped) (P . 4-61, 4-63) 3. Driver’s supplemental air bag/Horn (P .
25. Tilt steering (P .3-27) 26. Storage bin (P . 2-28) 27. Hood release lever (P . 3-23) 28 V ehicle Dynamic Control (VDC) off switch (if so equipped) (P .2-16) * Refer to the separate Navigation System Own- er’s Manual (if so equipped) . See the page number indicated in paren- theses for operating details.
SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates the vehicle speed. Odometer/T win trip odometer The odometer/twin trip odometer is displayed when the ignition switch is placed in the ON position. The odometer records the total distance the ve- hicle has been driven.
Loose fuel cap warning message Push the reset button 䊊 A for more than 1 second to reset the L OOSE FUEL CAP warning mes- sage 䊊 B after the fuel cap has been tightened. For additional information see “Fuel-filler cap” in the “Pre-driving checks and adjustments” section of this manual.
ENGINE COOLANT TEMPERA TURE GAUGE NO TE: The ignition switch must be placed in the ON position for the gauge to give a reading. The gauge indicates the engine coolant tempera- ture. The engine coolant temperature is within the normal range when the reading is within the zone 䊊 A shown in the illustration.
The indicates that the fuel-filler door is located on the passenger’s side of the vehicle. CAUTION ● If the vehicle runs out of fuel, the Malfunction Indicator Light (MIL) may come on. Refuel as soon as possible. After a few driving trips, the light should turn off.
Distance to empty (dte—mile or km) The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly be- ing calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption.
or Anti-lock Braking System (ABS) warning light NISSAN Intelligent Key™ warning light (if so equipped) Malfunction Indicator Light (MIL) or Brake warning light P position selecting warning light (CV.
CHECKING BULBS With all doors closed, apply the parking brake and place the ignition switch in the ON position without starting the engine. The following lights will come on: or , , , , , If equipped,.
Anti-lock Braking System (ABS) warning indicator When the parking brake is released and the brake fluid level is sufficient, if both the brake warning light and the Anti-lock Braking System (ABS) warning light illuminate, it may indicate the ABS is not functioning properly.
Low fuel warning light This light comes on when the fuel level in the fuel tank is getting low . Refuel as soon as it is conve- nient, preferably before the fuel gauge reaches E (Empty) . There will be a small reserve of fuel in the tank when the fuel gauge reaches E (Empty) , showing no more fuel bars.
● When a spare tire is mounted or a wheel is replaced the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.
Refer to “Seat belts” in the “Safety—Seats, seat belts and supplemental restraint system” section for precautions on seat belt usage. Supplemental air bag warning light When the ignition switch is placed in the ON or ST ART position, the supplemental air bag warn- ing light illuminates for about 7 seconds and then turns off.
The high beam indicator light also comes on when the passing signal is activated. Malfunction Indicator Light (MIL) If this indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control malfunction.
For vehicles with Intelligent Key: This light blinks when the ignition switch is placed in the L OCK position with the key removed from the ignition switch. The blinking security indicator light indicates that the security systems equipped on the vehicle are operational.
NISSAN Intelligent K ey™ door buzzer (if so equipped) The Intelligent Key door buzzer sounds if any one of the following improper operations is found. ● The ignition switch is not returned to the L OCK position when locking the doors. ● The Intelligent Key is left inside the vehicle when locking the doors.
● any request switch (Intelligent K ey models) . ● the keyfob or Intelligent Key . K eyfob and Intelligent Key operation: ● Push the button. All doors lock.
2. Place the ignition switch in the OFF or L OCK position and wait approximately 10 seconds. 3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key .
If the light still remains on and/or the en- gine will not start, see a NISSAN dealer for NISSAN V ehicle Immobilizer System ser- vice as soon as possible.
● Pre-mix windshield-washer fluid con- centrates with water to the manufactur- er’s recommended levels before pour- ing the fluid into the windshield-washer fluid reservoir. Do not use the windshield-washer fluid reservoir to mix the windshield-washer fluid con- centrate and water.
CAUTION Use the headlights with the engine run- ning to avoid discharging the vehicle battery. Headlight beam select 䊊 1 T o select the high beam function, push the lever forward. The high beam lights come on and the light illuminates. 䊊 2 Pull the lever back to select the low beam.
WARNING When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.
FOG LIGHT SWIT CH (if so equipped) T o turn the fog lights on, turn the headlight switch to the position, then turn the fog light switch to the position. T o turn the fog lights off, turn the fog light switch to the OFF position. The headlights must be on and the low beams selected for the fog lights to operate.
T o sound the horn, push the top portion of the steering wheel’s center pad. WARNING Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. T am- pering with the supplemental front air bag system may result in serious personal injury.
The front seats are warmed by built-in heaters. 1. Start the engine. 2. Push the low or high position of the switch, as desired, depending on the temperature. The indicator light in the switch will illumi- nate. The heater is controlled by a thermostat, automatically turning the heater on and off.
CAUTION ● The outlet and plug may be hot during or immediately after use. ● The power outlets are not designed for use with a cigarette lighter. ● Do not use with accessories that ex - ceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.
ST ORAGE BIN Pull the lid down to open the storage bin. Some models are equipped with a soft lining in the storage bin for storing sunglasses. WARNING Keep the storage bin closed while driving to prevent an accident. ST ORAGE TRA Y S WARNING Do not place sharp objects in the trays to help prevent injury in an accident or sud- den stop.
● The inside of the storage bin can get hot. Do not place objects inside which can melt or be easily deformed. WARNING Keep the lid closed while driving to help prevent contents from becoming projec- tiles causing injury in an accident of dur- ing a sudden stop.
CUP HOLDERS Adjust the cup holder size by turning the adjust- ment knob and sliding the cup holder divider to the desired position. CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.
GL OVE BOX Open the glove box by pulling the handle. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop. CONSOLE BO X T o open the console box, press in on the lever 䊊 1 and raise the lid 䊊 2 . T o close, push the lid down until the lock latches.
Once the rear seats have been lowered, the trunk divider can be opened by pressing down on the securing latch and pushing the divider toward the rear of the vehicle.
The cargo net helps keep packages in the cargo area from moving around while the vehicle is in motion. T o install the cargo net, attach the net to the retainers.
POWER WINDOWS (if so equipped) WARNING ● Make sure that all passengers have their hands, etc . inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows. ● Do not leave children unattended inside the vehicle.
Front passenger’s power window switch The passenger’s window switch operates only the corresponding passenger’s window . T o open the window , push the switch to the first detent and continue to hold it down until the desired window position is reached 䊊 1 .
Auto-reverse function The auto-reverse function can be activated when a window is closed by automatic operation. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window oc- curs.
MANUAL WINDOWS (if so equipped) The side windows can be opened or closed by turning the hand crank on each door. ELECTRIC MOONROOF This moonroof only operates with the ignition switch placed in the ON position. NO TE: If the battery is discharged or is discon- nected, the moonroof may not operate cor- rectly, and must be reset.
WARNING ● In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints. ● Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.
WARNING There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc .
● The driver’s door is opened and then closed while the ignition switch is placed in the OFF position. ● The ignition switch is placed in the OFF position while all doors are closed. The interior light will turn off while the 30 second timer is activated when: ● The driver’s door is locked by the keyfob, a key or the lock -unlock switch.
The light illuminates when the trunk lid is opened. When the trunk lid is closed, the light goes off. For bulb replacement procedures, refer to “Exte- rior and interior lights” in the “Maintenance and do-it-yourself” section of this manual.
MEMO 2-42 Instruments and controls I n f o r m a t i o n P r o v i d e d b y :.
3 Pre-driving checks and adjustments K e y s .............................................3 - 2 NISSAN Intelligent K ey™ (if so equipped) .........3 - 2 NISSAN V ehicle Immobilizer System keys .........3 - 4 Doors ...................................
1. T wo master keys (black) with transpon- der chip and chrome NISSAN brand symbol on one side 2. T ransponder chip 3. K ey number plate A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet) , not in the vehicle.
Never leave these keys in the vehicle. As many as 4 Intelligent Keys can be registered and used with one vehicle. The new keys must be registered by a NISSAN dealer prior to use with the Intelligent Key and NISSAN V ehicle Immobi- lizer System of your vehicle.
CAUTION Always carry the mechanical key installed in the Intelligent Key slot. See “Doors” in this section and “Storage” in the “Instruments and controls” section of this manual.
L OCKING WITH KEY Manual (if so equipped) T o lock a door, turn the key toward the front of the vehicle 䊊 1 . T o unlock, turn the key toward the rear 䊊 2 . P ower (if so equipped) The power door lock system allows you to lock or unlock all doors at the same time.
L OCKING WITH POWER DOOR L OCK SWIT CH T o lock all the doors without a key, push the door lock switch (driver’s or front passenger’s side) to the lock position 䊊 1 . When locking the door this way , be certain not to leave the key inside the vehicle.
CHILD SAFETY REAR DOOR L OCK Child safety locks help prevent the rear doors from being opened accidentally , especially when small children are in the vehicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the unlock position 䊊 1 , the door can be opened from the outside or the inside.
● Do not place the keyfob for an extended period in an area where temperatures exceed 140°F (60°C) . ● Do not attach the keyfob with a key holder that contains a magnet. ● Do not place the keyfob near equip- ment that produces a magnetic field, such as a TV, audio equipment and per- sonal computers.
Unlocking doors Press the button on the keyfob once. ● Only the driver’s door unlocks. ● The hazard warning lights flash once if all doors are completely closed with the ignition switch in any position except the ON posi- tion.
Using the panic alarm (if so equipped) If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention by pressing and holding the button on the keyfob for longer than 0.5 seconds. The panic alarm and headlights will stay on for 25 seconds.
The hazard warning lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. Deactivating the horn beep feature does not si- lence the horn if the alarm is triggered. WARNING ● Radio waves could adversely affect electric medical equipment.
● When the vehicle is parked near a parking meter. In such cases, correct the operating conditions before using the Intelligent K ey function or use the mechanical key . Although the life of the battery varies depending on the operating conditions, the battery’s life is approximately 2 years.
OPERA TING RANGE The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range from the request switch 䊊 1 .
● T o prevent the Intelligent K ey from being left inside the vehicle, make sure you carry the Intelligent Key with you and then lock the doors. ● Do not pull the door handle before pushing the door handle request switch. The door will be unlocked but will not open.
NO TE: ● Doors lock with the door handle request switch while a mechanical key is in the igni- tion switch or the ignition switch is pushed in. ● Doors lock with the door handle request switch while the ignition switch is not in the L OCK position.
Unlocking doors 1. Carry the Intelligent Key . 2. Push the door handle request switch 䊊 1 . 3. The hazard warning lights flash once and the outside buzzer sounds once. 4. Push the door handle request switch 䊊 1 again within 60 seconds to unlock all doors.
Opening the trunk lid 1. Push the trunk opener request switch 䊊 A for more than 1 second while carrying the Intel- ligent K ey with you. 2. The trunk will unlatch.
CAUTION After locking the doors using the Intelli- gent Key, be sure that the doors have been securely locked by operating the door handles. Unlocking doors 1. Press the button on the Intelligent Ke y. 2. The hazard warning lights flash once. 3. Press the button again within 60 sec- onds to unlock all doors.
Releasing the trunk lid Press the button for longer than 0.5 sec- onds to open the trunk lid. The trunk release button will not operate when the ignition switch is placed in the ON position.
Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the Intelligent K ey. T o deactivate: Press and hold the and buttons for at least 2 seconds. The hazard warning lights will flash 3 times to confirm that the horn beep feature has been deactivated.
CAUTION When the buzzer sounds and the warning light illuminates, be sure to check both the vehicle and the Intelligent Key. W ARNING SIGNALS T o help prevent the vehicle from moving unex- pectedly by.
TROUBLESHOO TING GUIDE Symptom Possible Cause Remedy When pushing the door handle request switch The front door beep sounds for approxi- mately 2 seconds. The doors cannot be locked. T ake out the Intelligent Key from the vehicle and push the door handle request switch.
1. Pull the hood lock release handle 䊊 1 located below the instrument panel until the hood springs up slightly . 2. Locate the lever 䊊 2 in between the hood and grille and push the lever sideways with your fingertips. 3. Raise the hood 䊊 3 . 4. Remove the support rod 䊊 4 and insert it into the slot on the underside of the hood 䊊 5 .
KEY OPERA TION (if so equipped) T o open the trunk lid, turn the key clockwise. T o close the trunk lid, lower and push the trunk lid down securely . TRUNK LID RELEASE The trunk lid release is located on the floor to the left of the driver’s seat. T o open the trunk lid, pull the trunk lid release.
T o open the trunk from the inside, pull the illumi- nated release handle until the lock releases and push up on the trunk lid. The release handle is made of a material that glows in the dark after a brief exposure to ambient light. The handle is located inside the trunk compart- ment on the interior of the trunk lid.
● Do not fill a portable fuel container in the vehicle or trailer. Static electricity can cause an explosion of flammable liquid, vapor or gas in any vehicle or trailer. T o reduce the risk of serious injury or death when filling portable fuel containers: – Always place the container on the ground when filling.
Loose Fuel Cap warning message The L OOSE FUEL CAP warning message dis- plays in the odometer when the fuel-filler cap is not tightened correctly after the vehicle has been refueled. It may take a few driving trips for the message to be displayed. T o turn off the warning message, perform the following: 1.
T o block out glare from the front, swing down the sun visor 䊊 1 . T o block glare from the side, disconnect the sun visor from the center mount and swing it to the side 䊊 2 . V ANITY MIRRORS (if so equipped) T o access the vanity mirror, pull the sun visor down and flip open the mirror cover.
OUTSIDE MIRRORS WARNING Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.
Heated mirrors (Canada only) (if so equipped) Some outside mirrors can be heated to defrost, defog, or de-ice for improved visibility. Push the rear window defroster switch to activate the heat- ing function. Push the switch again to deactivate, or the heating function will automatically turn off after approximately 15 minutes.
MEMO Pre-driving checks and adjustments 3-31 I n f o r m a t i o n P r o v i d e d b y :.
4 Display screen, heater, air conditioner, audio and phone systems Control panel buttons — color screen with Navigation System (if so equipped) ..................4 - 2 How to use the touch screen ....................4 - 3 How to use the back button .
CD care and cleaning .......................... 4-60 Steering wheel switch for audio control (if so equipped) ............................... 4-61 Antenna ...................................... 4-62 Car phone or CB radio . . ..........................
WARNING ● Do not disassemble or modify this sys- tem. If you do, it may result in accidents, fire, or electrical shock. ● In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell coming from it, stop using the system immediately and contact your nearest NISSAN dealer.
*For Navigation system control buttons, refer to the separate Navigation System Owner’s Manual. When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will discharge the battery, and the engine will not start.
Adjusting the item: For screens where an item can be adjusted incre- mentally , such as when adjusting the bass and treble for the audio system, touch the “+” key 䊊 1 or the “ ⫺ ” key 䊊 2 to adjust the settings of an item.
● OK: Completes the character input. T ouch screen maintenance If you clean the display screen, use a dry, soft cloth. If additional cleaning is necessary , use a small amount of neutral detergent with a soft cloth. Never spray the screen with water or de- tergent.
System setup Select the “System” key to select and/or adjust various functions of the system. A screen with additional options will appear. Display: Select the “Display” key to adjust the appearance of the display.
Clock: Select the “Clock” key to adjust the time and the appearance of the clock on the display. The fol- lowing settings can be adjusted: Time Format The clock can be set to 12 hours or 24 hours. Use GPS Clock When this setting is activated, the clock is set and continually updated via the GPS used by the Navigation System.
appears on the screen or a button on the unit (such as the button) is pressed and held for two seconds. Reset all settings/memory: Select the “Reset All Settings/Memory” key to return all settings to default and to clear the memory . T raffic setup Refer to the separate Navigation System Own- er’s Manual for information regarding this item.
HOW T O READ THE DISPLA YED LINES Lines which indicate the vehicle clearance and distances to objects with reference to the bum- per line 䊊 A are displayed on the monitor. They are indicated as reference distances to objects. The lines and colors in the display indi- cate distances from the back bumper line 䊊 A in the illustration.
Backing up on a steep uphill When backing up the vehicle up a hill, the dis- tance guide lines and the vehicle width guide lines are shown closer than the actual distance. For example, the display shows 3 ft (1.0 m) to the place 䊊 A , but the actual 3 ft (1.
the hill is the place 䊊 B . Note that any object on the hill is closer than it appears on the monitor. Backing up behind a projecting object The position 䊊 C is shown farther than the position 䊊 B in the display. However, the position 䊊 C is actually at the same distance as the position 䊊 A .
ADJUSTING THE SCREEN (models without Navigation System) T o adjust the quality of the screen, press the setting control knob on the audio system. ● T o adjust the Brightness or Contrast, press the setting control knob repeatedly until the setting you wish to adjust is displayed.
OPERA TING TIPS ● When the shift selector is shifted to R (Re- verse) , the monitor screen automatically changes to the RearView Monitor mode. However, the radio can be heard. ● It may take some time until the RearView Monitor is displayed after the shift selector has been shifted to R (Reverse) .
Adjust air flow direction for the driver’s and pas- senger’s side 䊊 1 , and center 䊊 2 ventilators by moving the ventilator slide and/or ventilator as- semblies. Open or close the ventilators 䊊 1 by using the dial. Move the dial toward the to open the ven- tilators or toward the to close them.
1. Fan control dial 2. Air recirculation button 3. T emperature control dial 4. Air flow control dial 5. Rear window defroster T ype A WHA0470 Display screen, heater, air conditioner, audio and phone .
1. Fan control dial 2. Air recirculation button 3. T emperature control dial 4. Air conditioner button 5. Air flow control dial 6. Rear window defroster CONTROLS Fan control dial The fan control dial turns the fan on and off, and controls fan speed. Air flow control dial The air flow control dial allows you to select the air flow outlets.
Press the button to the on position when: ● driving on a dusty road. ● to prevent traffic fumes from entering pas- senger compartment. ● for maximum cooling when using the air con- ditioner. When the button is pressed, the air con- ditioner automatically turns on and the indicator illuminates.
● When the or position is se- lected, the air conditioner automatically turns on (however, the indicator light will not illuminate) . In this position, the A/C cannot be turned off.
● For quick cooling when the outside tem- perature is high, push the button to the on position (indicator light on) . Be sure to return the button to the off position for normal cooling. MAX A/C may be used for quick cooling. Dehumidified heating This mode is used to heat and dehumidify the air.
WHA1116 WHA1117 4-20 Display screen, heater, air conditioner, audio and phone systems I n f o r m a t i o n P r o v i d e d b y :.
WHA1118 WHA1119 Display screen, heater, air conditioner, audio and phone systems 4-21 I n f o r m a t i o n P r o v i d e d b y :.
WHA1121 4-22 Display screen, heater, air conditioner, audio and phone systems I n f o r m a t i o n P r o v i d e d b y :.
The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner.
Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter) , static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response.
Compact disc (CD) player CAUTION ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD player. ● T rying to load a CD with the CD door closed could damage the CD and/or CD player. ● Only one CD can be loaded into the CD player at a time.
Compact disc with MP3 or WMA (if so equipped) T erms: ● MP3 — MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well-known compressed digital audio file format. This format allows for near “CD quality” sound, but at a fraction of the size of normal audio files.
● If there is a file in the top level of the disc, “Root Folder” is displayed. ● The playback order is the order in which the files were written by the writing software.
Specification chart : Supported media CD, CD-R, CD-RW Supported file systems ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported.
T roubleshooting guide: Symptom Cause and Countermeasure Cannot play Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player.
Universal Serial Bus (USB) memory (if so equipped) This system supports various USB memory sticks, USB hard drives and iP od 姞 players. There are some USB devices which may not be sup- ported with this system. ● Make sure that the USB device is connected correctly into the USB connector.
● If the iPod 姞 automatically selects large video podcast files while in the shuffle mode, the vehicle center display may momentarily black out, but it will soon recover. ● Improperly plugging in the iP od 姞 may cause a checkmark to be displayed on and off (flickering) .
1. FM-AM button 2. CD eject button 3. SEEK button 4. CD button 5. CD insert slot 6. AUX button 7. TUNE button 8. MENU button 9. RPT button 10. AUX IN jack 11.
Press the SEEK or or TUNE or button to adjust the Bass, T reble, Fade and Balance to the desired level. Fade adjusts the sound level between the front and rear speak- ers and Balance adjusts the sound between the right and left speakers.
4. Other buttons can be set in the same man- ner. If the battery cable is disconnected or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Compact disc (CD) player operation Place the ignition switch in the ACC or ON position and carefully insert the compact disc into the slot with the label side up.
1. MUTE button 2. DISP/TEXT button 3. FM-AM button 4. CD button 5. CD insert slot 6. iP od button 7. AUX button 8. CL OCK button 9. CD eject button 10. TUNE/FF-REW/FOLDER button 11. SCAN/RPT button 12. AUDIO button 13. AUX IN jack 14. Station select (1 - 6) buttons 15.
MUTE button: Press the button to mute the audio sound. Press the button again to resume playing the audio at its previous volume. AUDIO button (Bass, T reble, Fade, Bal- ance, SSV , Beep) : Press the .
TUNE button (T uning) : Press the TUNE/FF-REW/FOLDER button or for manual tuning. SEEK tuning: Press the SEEK/TRACK button or to tune from low to high or high to low frequen- cies and to stop at the next broadcasting station. SCAN tuning: Press the SCAN/RPT button to stop at each broadcasting station for 5 seconds.
CD with MP3 or WMA: When the TUNE/FF-REW/FOLDER button (fast forward) or (reverse) is pressed for less than 1.5 seconds while the compact disc is playing, the folders in the CD will change. When the TUNE/FF-REW/FOLDER button (fast forward) or (reverse) is pressed for more than 1.
1. SCAN button 2. Station select (1 - 6) buttons 3. CD insert slot 4. iP od MENU button 5. CD eject button 6. TUNE/SCROLL knob/Setting control button 7. SEEK/CA T buttons 8. AUX IN jack 9. AUX button* 10. CD button 11. FM-AM button 12. RPT button 13. POWER/VOLUME control knob 14.
T o turn the system off, press the VOL/ON·OFF control knob. T urn the VOL/ON·OFF control knob to adjust the volume. This vehicle may be equipped with Speed Sen- sitive V olume (SSV) for audio. When this feature is active, the audio volume changes as the driving speed changes.
Display settings: T o adjust the brightness or contrast of the display screen, press the ENTER button until the chosen setting is displayed. Use the TUNE/SCROLL knob to adjust the display to the desired level. On-screen Clock: The clock is shown in the upper right corner of the screen.
iPod 姞 MENU button This button can only be used for iP od 姞 opera- tions. See “iPod 姞 player operation without Navi- gation System (T ype B)” in this section for details about the function of this button.
If the battery cable is disconnected or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Compact disc (CD) player operation Place the ignition switch in the ACC or ON position and carefully insert the compact disc into the slot with the label side up.
TUNE/SCROLL knob (MP3/WMA CD only) : If an MP3/WMA CD with multiple folders is play- ing, turn the TUNE/SCROLL knob to change folders. T urn the knob to the left to skip back a folder.
1. XM button 2. CD insert slot 3. Display screen 4. CD eject button 5. SETUP button 6. BACK button 7. TUNE/SCROLL knob, AUDIO button 8. Station select (1 - 6) buttons 9. AUX button 10. VOL/ON-OFF control knob 11. SEEK/CA TEGORY button 12. CD button 13.
T urn the VOL/ON·OFF control knob to adjust the volume. This vehicle may be equipped with Speed Vol- ume for audio. When this feature is active, the audio volume changes as the driving speed changes. Audio settings: Press the SETUP button to display the audio settings on the screen.
If another audio source is playing when the FM·AM button is pressed, the audio source play- ing will automatically be turned off and the last radio station played will begin playing. The FM stereo indicator (ST) is shown on the screen during FM stereo reception.
T uning with the touchscreen: When in AM or FM mode, the radio can be tuned using the touchscreen. T o bring up the visual tuner, touch the “T une” key on the lower right corner of the screen. A screen appears with a bar running from low frequencies on the left to high frequencies on the right.
CD/MP3 display mode While listening to a CD or an MP3/WMA CD, certain text may be displayed (when a CD en- coded with text is being used) . Depending on how the CD or MP3/WMA CD is encoded, the text is displayed listing the artist, album and song title.
Browse: T ouch the “Browse” key to display the titles on the CD in list format. T ouch the title of a song in the list to begin playing that song. If an MP3 CD is playing, touching the “Browse” key will also list the folders on the disc. Follow the procedure for selecting a song with the touchscreen to choose a folder.
For more information about the USB input jack, see “USB interface” in this section. EJECT button: When the button is pressed with a com- pact disc loaded, the compact disc will eject and the last source will be played. When the button is pressed twice with a compact disc loaded, the compact disc will be ejected further for easier CD removal.
Play information Information about the audio files being played can be displayed on the display screen of the vehicle’s audio system. Depending on how the audio files are encoded, information such as Folder, Song and Artist will be displayed. The track number and number of total tracks in the folder are displayed on the screen as well.
The current play pattern of the USB device is displayed on the screen unless no pattern is applied. TUNE/SCROLL knob: If there are multiple folders with audio files on the USB device, turn the TUNE/SCROLL knob to change folders. T urn the knob to the left to skip back a folder.
Play information Information about the audio files being played is shown on the display screen of the vehicle’s audio system. T ouch “Browse” to display the list of folders and files on the USB device. T ouch the name of a song on the screen to begin playing that song.
iP od 姞 * PLA YER OPERA TION WITHOUT NA VIGA TION S Y STEM (T ype A) (if so equipped) Connecting iP od 姞 The iP od 姞 outlet connector is located on the center console. Y our vehicle is equipped with the specialized cable for connecting the iPod 姞 to your vehicle audio unit.
ENTER and BACK buttons: Press the ENTER button while the top menu is displayed to show program details on the audio display . Use the SEEK buttons or to scroll through the choices and press the ENTER button to make a selection. Press the BACK button to return to the previous display .
the battery of your iPod 姞 (if compatible) is charged during the connection to the vehicle. While connected to the vehicle, the iPod 姞 can only be operated by the vehicle audio controls. T o disconnect the iP od 姞 from the vehicle, remove the USB end of the cable from the USB jack on the vehicle, then remove the cable from the iP od 姞 .
ALL RPT : all songs in the current list are re- peated. RPT OFF: no repeat play pattern is applied. RDM button: Press the RDM button while a track is playing to change the play pattern as follows: TRK SHUFFLE → ALBUM SHUFFLE → SHUFFLE OFF TRK SHUFFLE: the tracks in the current list will be played randomly .
Audio main operation AUX button: Place the ignition switch in the ACC or ON position and press the AUX button repeatedly until the iP od 姞 mode is displayed on the screen. If another audio source is playing and the iPod 姞 is connected, press the AUX button repeatedly to switch to the iP od 姞 mode.
Random: T ouch the “Random” key to apply a random play pattern to the iPod 姞 . When the random mode is active, the icon is displayed to the left of the song title or album name to denote which random pattern is applied. T o cancel Random mode, touch the “Random” key until no icon is displayed.
1. T uning switch 2. MODE select switch 3. POWER on/off switch 4. V olume control switch 1. T uning switch 2. Phone operation switch 3. POWER on and MODE select switch 4. V olume control switch STEERING WHEEL SWIT CH FOR AUDIO CONTROL (if so equipped) The audio system can be operated using the controls on the steering wheel.
MODE select switch (models with Navigation System) Push the MODE select switch to change the mode in the following sequence: AM/FM* → XM** → CD*** → USB/AUX*** → AM/FM* * When using the MODE switch, the audio mode switches to the preset bank (AM, FM1 or FM2) that was last active.
When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following precautions; otherwise, the new equipment may adversely affect the engine control system and other electronic parts. WARNING ● A cellular telephone should not be used for any purpose while driving so full attention may be given to vehicle op- eration.
Y our NISSAN is equipped with the Bluetooth 姞 Hands-Free Phone System. If you have a com- patible Bluetooth 姞 enabled cellular phone, you can set up the wireless connection between your cellular phone and the in-vehicle phone module.
garage, near a tall building or in a moun- tainous area. – Y our cellular phone is locked to prevent it from being dialed. ● When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult to hear the other person’s voice dur- ing a call.
Operating tips T o get the best performance out of the NISSAN V oice Recognition system, observe the following: ● K eep the interior of the vehicle as quiet as possible. Close the windows to eliminate surrounding noises (traffic noises, vibration sounds, etc.
– NO T “One eight hundred six six two sixty two hundred,” and – NO T “One eight oh oh six six two sixty two hundred” ● Numbers can be spoken in small groups.
Y ou can also use the button to interrupt the system feedback and give a command at once. See “List of voice commands” and “During a call” in this section for more information. PHONE/END While the voice recognition system is active, press and hold the button for 5 seconds to quit the voice recognition system at any time.
3. Say: “ Add phone” 䊊 B . The system acknowl- edges the command and asks you to initiate connecting from the phone handset 䊊 C . The connecting procedure of the cellular phone varies according to each cellular phone model. See the cellular phone Own- er’s Manual for details.
LIST OF VOICE COMMANDS Main Menu “Call” “Phonebook” “Recent Calls” “Connect Phone” When you press and release the button on the steering wheel, you can choose from the commands on the Main Menu. The following pages describe these commands and the com- mands in each sub-menu.
If a call back number does not exist, the system announces, “There is no number to call back” and ends the VR session. During a call During a call there are several command options available. Press the button on the steering wheel to mute the receiving voice and enter com- mands.
“T ransfer Entry” 䊊 A Use the T ransfer Entry command to store a new name in the system. When prompted by the system, say the name you would like to give the new entry . For example, say: “Mary .” If the name is too long or too short, the system tells you, then prompts you for a name again.
difficulty recognizing. For more information see “Record name” in this section. NO TE: Each phone has its own separate phone- book. Y ou cannot access Phone A’s phone- book if you are currently connected with Phone B . “List Names” 䊊 A Use the List Names command to hear all the names and locations in the phone book.
Use the Recent Calls command to access out- going, incoming or missed calls. “Outgoing” 䊊 A Use the Outgoing command to list the outgoing calls made from the vehicle. “Incoming” 䊊 B Use the Incoming command to list the incoming calls made to the vehicle.
5. Press the button. For information on selecting a different lan- guage, see “Choosing a language” in this section. 6. Voice memory A or memory B is selected automatically . If both memory locations are already in use, the system will prompt you to overwrite one.
● delete ● dial nine seven two six six ● call seven six three oh one ● go back ● call five six two eight zero ● dial six six four three seven MANUAL CONTROL While using the voice recognition system, it is possible to select menu options by using the steering wheel controls instead of speaking voice commands.
Symptom Solution System fails to interpret the command correctly. 1. Ensure that the command is valid. See “List of voice commands” in this section. 2. Ensure that the command is spoken after the tone. 3. Speak clearly without pausing between words and at a level appropriate to the ambient noise level in the vehicle.
MEMO 4-78 Display screen, heater, air conditioner, audio and phone systems I n f o r m a t i o n P r o v i d e d b y :.
5 Starting and driving Precautions when starting and driving ................5 - 2 Exhaust gas (carbon monoxide) ..................5 - 2 Three-way catalyst ..............................5 - 2 Tire Pressure Monitoring System (TPMS) (if so equipped) ...
WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle.
● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously re- duce the three-way catalyst’s ability to help reduce exhaust pollutants.
● The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h) . Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving) . ● The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted for all 4 tires.
Some examples are: – Facilities or electric devices using similar radio frequencies are near the vehicle. – If a transmitter set to similar frequencies is being used in or near the vehicle. – If a computer (or similar equipment) or a DC/AC converter is being used in or near the vehicle.
5. If there is nothing in the way , steer the ve- hicle to follow the road while vehicle speed is reduced. Do not attempt to drive the ve- hicle back onto the road surface until vehicle speed is reduced. 6. When it is safe to do so, gradually turn the steering wheel until both tires return to the road surface.
NISSAN is committed to safe driving. However, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol-related accidents.
CAUTION ● Be sure to carry the Intelligent Key with you when operating the vehicle. ● Never leave the Intelligent Key inside the vehicle when you leave the vehicle.
CONTINUOUSL Y V ARIABLE TRANSMISSION (CVT) (if so equipped) The ignition lock is designed so that the ignition switch cannot be turned to the LOCK position until the shift selector is moved to the P (Park) position. ● When moving the ignition switch to the L OCK position, make sure the shift selector is in the P (Park) position.
MANUAL TRANSMISSION (if so equipped) The ignition switch includes a device that helps prevent accidental removal of the key while driv- ing. The key can only be removed when the ignition switch is in the L OCK position.
If the no start condition re-occurs, NISSAN rec- ommends placing the registered key on a sepa- rate key ring to avoid interference from other devices. ● Make sure the area around the vehicle is clear.
When the Intelligent K ey warning light in the meter blinks in red and the inside warning buzzer emits a short beep, be sure that the shift selector is in the P (Park) position and the ignition switch is securely returned to the L OCK position.
CONTINUOUSL Y V ARIABLE TRANSMISSION (CVT) (if so equipped) WARNING ● Do not depress the accelerator pedal while shifting from P (Park) or N (Neu- tral) to R (Reverse) , D (Drive) or L (Low) . Always depress the brake pedal until shifting is completed.
T o move the shift selector: Push the button 䊊 A while depressing the brake pedal Push the button 䊊 A to shift Shift without pushing button 䊊 A Shifting After starting the engine, fully depress the brake pedal and move the shift selector from P (Park) to any of the desired shift positions.
D (Drive) : Use this position for all normal forward driving. L (Low) : Use this position for maximum engine braking on steep downhill gradients/climbing steep slopes and whenever approaching sharp bends. Do not use the L (Low) position in any other circum- stances.
M1 (1st) : Use this position when climbing steep hills slowly or driving slowly through deep snow, sand or mud, or for maximum engine braking on steep downhill grades. ● Remember not to drive at high speeds for extended periods of time in lower than M6 range.
3. Remove the shift lock release cover as shown. 4. Insert a small screwdriver in the shift lock release slot and push down. 5. Move the shift selector to the N (Neutral) position while holding down the shift lock release. 6. Now the vehicle may be moved to the de- sired location.
WARNING When the high fluid temperature protec- tion mode or fail-safe operation occurs, vehicle speed may be gradually reduced. The reduced speed may be lower than other traffic , which could increase the chance of a collision. Be especially care- ful when driving.
T o back up, lift up on the shift selector ring 䊊 1 and then move it to the R (Reverse) position after stopping the vehicle completely . The shift selector ring 䊊 1 returns to its original position when the shift selector is moved to the N (Neutral) position.
WARNING ● Be sure the parking brake is fully re- leased before driving. Failure to do so can cause brake failure and lead to an accident. ● Do not release the parking brake from outside the vehicle. ● Do not use the shift selector in place of the parking brake.
1. ACCEL/RES switch 2. COAST/SET switch 3. CANCEL switch 4. ON/OFF switch PRECAUTIONS ON CRUISE CONTROL ● If the cruise control system malfunctions, it cancels automatically. The SET indicator light in the instrument panel then blinks to warn the driver.
● The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control. T o cancel the preset speed, use one of the following three methods. ● Push the CANCEL button; the SET indicator light in the instrument panel goes out.
● Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelerator position. ● Drive at moderate speeds on the highway . Driving at high speed lowers fuel economy . ● Avoid unnecessary stopping and braking. Maintain a safe distance behind other ve- hicles.
WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. ● Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) for CVT models or in an appropriate gear for manual transmission models.
WARNING ● If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be harder to operate. ● When the power steering warning light illuminates with the engine running, there will be no power assist for the steering.
WARNING ● While driving on a slippery surface, be careful when braking, accelerating or downshifting. Abrupt braking or accel- erating could cause the wheels to skid and result in an accident. ● If the engine is not running or is turned off while driving, the power assist for the brakes will not work.
WARNING Do not pump the brake pedal. Doing so may result in increased stopping distances. Self-test feature The ABS includes electronic sensors, electric pumps, hydraulic solenoids and a computer.
When the VDC system operates, the indi- cator in the instrument panel flashes so note the following: ● The road may be slippery or the system may determine some action is required to help keep the vehicle on the steered path. ● Y ou may feel a pulsation in the brake pedal and hear a noise or vibration from under the hood.
● When driving on extremely inclined sur- faces such as higher banked corners, the VDC system may not operate prop- erly and the indicator may flash or both the and indicator lights may illuminate.
3. Tire chains may be used. For details see “Tire chains” in the “Maintenance and do-it- yourself” section of this manual. SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter: ● A scraper and stiff-bristled brush to remove ice and snow from the windows and wiper blades.
T o use the engine block heater: 1. T urn the engine off. 2. Open the hood and unwrap the engine block heater cord. 3. Plug the engine block heater cord into a grounded 3 wire, 3 pronged extension cord. 4. Plug the extension cord into a Ground Fault Interrupt (GFI) protected, grounded 110- volt AC (V AC) outlet.
MEMO 5-32 Starting and driving I n f o r m a t i o n P r o v i d e d b y :.
6 In case of emergency Flat tire ...........................................6 - 2 Tire Pressure Monitoring System (TPMS) (if so equipped) ................................6 - 2 Changing a flat tire .............................6 - 2 Jump starting .....
TIRE PRESSURE MONIT ORING S Y STEM (TPMS) (if so equipped) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pres- sure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated.
WARNING ● Make sure the parking brake is securely applied and the manual transmission is shifted into R (Reverse) , or the CVT is shifted into P (Park) . ● Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous.
2. T o remove the jack, turn the jack screw counterclockwise and lift out. Removing bolt-on wheel cover (if so equipped) CAUTION Do not use your hands to pry off wheel caps or wheel covers. Doing so could re- sult in personal injury. Wheel cover attachment to the wheel is made by one of the wheel lug nuts.
Jacking up vehicle and removing the damaged tire WARNING ● Never get under the vehicle while it is supported only by the jack. If it is nec- essary to work under the vehicle, sup- port it with safety stands. ● Use only the jack provided with your vehicle to lift the vehicle.
Always refer to the proper illustrations for the correct placement and jack-up points for your specific vehicle model and jack type. Carefully read the caution label attached to the jack body and the following instruc- tions. 1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench.
4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated ( 䊊 A , 䊊 B , 䊊 C , 䊊 D ). Lower the vehicle completely . WARNING ● Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off.
WARNING ● Always make sure that the spare tire and jacking equipment are properly se- cured after use. Such items can become dangerous projectiles in an accident or sudden stop.
● If the battery of a vehicle equipped with the Intelligent Key system is dis- charged, the ignition switch cannot be moved from the LOCK position, even using the mechanical key or the valet key.
CAUTION ● Always connect positive ( ⫹ ) to positive ( ⫹ ) and negative ( ⫺ ) to body ground (for example, strut mounting bolt, engine lift bracket, etc .) — not to the battery. ● Make sure the jumper cables do not touch moving parts in the engine com- partment and that the cable clamps do not contact any other metal.
If your vehicle is overheating (indicated by an extremely high temperature gauge reading) , or if you feel a lack of engine power, detect abnormal noise, etc., take the following steps. WARNING ● Do not continue to drive if your vehicle overheats. Doing so could cause engine damage or a vehicle fire.
When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could dam- age your vehicle. T owing instructions are avail- able from a NISSAN dealer. Local service opera- tors are generally familiar with the applicable laws and procedures for towing.
T OWING RECOMMENDED B Y NISSAN NISSAN recommends that your vehicle be towed with the driving (front) wheels off the ground or place the vehicle on a flat bed truck as illustrated.
● When towing Continuously Variable T ransmission (CVT) or manual trans- mission (M/T) models with the rear wheels on the ground (if you do not use towing dollies) : Always release the parking brake.
If your vehicle is stuck in sand, snow, mud, etc., use a tow strap or other device designed specifi- cally for vehicle recovery. Always follow the manufacturer’s instructions for the recovery de- vice. Do not use the tie-down hooks for towing or vehicle recovery .
MEMO 6-16 In case of emergency I n f o r m a t i o n P r o v i d e d b y :.
7 Appearance and care Cleaning exterior ..................................7 - 2 W ashing ......................................7 - 2 W axing ........................................7 - 2 Removing spots ................................7 - 3 Underbody .
In order to maintain the appearance of your ve- hicle, it is important to take proper care of it. T o protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads.
REMOVING SPO TS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store.
CAUTION Follow the directions below to avoid staining or discoloring the wheels: ● Do not use a cleaner that uses strong acid or alkali contents to clean the wheels. ● Do not apply wheel cleaners to the wheels when they are hot. The wheel temperature should be the same as am- bient temperature.
CAUTION ● Never use benzene, thinner, or any simi- lar material on the interior surfaces or surface damage may occur. Such dam- age is not covered under the NISSAN warranty. ● Small dirt particles can be abrasive and damaging to leather surfaces and should be removed promptly.
Floor mat positioning aid This vehicle includes a front floor mat bracket to act as a floor mat positioning aid. Genuine NISSAN floor mats have been specially designed for your vehicle model. The driver’s and passen- ger’s side floor mats have a grommet hole incor- porated in them.
T emperature High temperatures accelerate the rate of corro- sion to those parts which are not well ventilated. Air pollution Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use acceler- ates the corrosion process.
MEMO 7-8 Appearance and care I n f o r m a t i o n P r o v i d e d b y :.
8 Maintenance and do-it-yourself Maintenance requirements ..........................8 - 2 General maintenance ..............................8 - 2 Explanation of general maintenance items .........8 - 2 Maintenance precautions .........................
Y our NISSAN has been designed to have mini- mum maintenance requirements with long ser- vice intervals to save you both time and money. However, some day-to-day and regular mainte- nance is essential to maintain your NISSAN’s good mechanical condition, as well as its emis- sions and engine performance.
When driving in areas using road salt or other corrosive materials, check lubrication frequently . Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely .
Seat belts Check that all parts of the seat belt system (for example, buckles, anchors, adjusters and retractors) operate properly and smoothly, and are installed securely .
When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle.
MR20DE engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Brake fluid reservoir/Clutch fluid reservoir (M/T model) 4. Battery 5. Air cleaner 6.
QR25DE engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Brake fluid reservoir/Clutch fluid reservoir (M/T model) 4. Battery 5. Air cleaner 6. Fuse/Fusible link box 7. Radiator cap 8. Engine oil dipstick 9. Drive belt location 10. Windshield-washer fluid reservoir * Engine cover removed for clarity.
The engine cooling system is filled at the factory with a pre-diluted mixture of 50% Genuine NISSAN Long Life Antifreeze/Coolant (blue) and 50% water to provide year-round anti-freeze and coolant protection. The antifreeze solution con- tains rust and corrosion inhibitors.
CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir when the engine is cold. If the coolant level is below the MIN level 䊊 B , add coolant to the MAX level 䊊 A . If the reservoir is empty , check the coolant level in the radiator when the engine is cold.
CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply the parking brake. 2. Start the engine and let it idle until it reaches operating temperature. 3. T urn off the engine. Wait more than 10 minutes for the oil to drain back into the oil pan.
CAUTION Oil level should be checked regularly. Op- erating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty. Make sure to follow the engine oil changing inter- vals in the maintenance booklet.
4. Place a large drain pan under the drain plug 䊊 B . 5. Remove the drain plug 䊊 B with a wrench by turning it counterclockwise and completely drain the oil. If the oil filter is to be changed, remove and replace it at this time. See “Changing engine oil filter” later in this section.
CHANGING ENGINE OIL FIL TER 1. Park the vehicle on a level surface and apply the parking brake. 2. T urn the engine off. 3. Place a large drain pan under the oil filter 䊊 C . 4. Loosen the oil filter with an oil filter wrench by turning it counterclockwise.
For further brake and clutch fluid specification information, refer to “Capacities and recom- mended fuel/lubricants” in the “T echnical and consumer information” section of this manual. WARNING ● Use only new fluid from a sealed con- tainer.
WINDSHIELD-W ASHER FLUID RESERVOIR Fill the windshield-washer fluid reservoir periodi- cally . Add windshield-washer fluid when the low windshield-washer fluid warning light comes on (if so equipped) . T o fill the windshield-washer fluid reservoir, lift the cap off the reservoir and pour the windshield- washer fluid into the reservoir opening.
● Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the battery which can generate heat, reduce bat- tery life, and in some cases lead to an explosion. ● When working on or near a battery, al- ways wear suitable eye protection and remove all jewelry.
V ehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP ST ARTING If jump starting is necessary , see “Jump starting” in the “In case of emergency” section of this manual. If the engine does not start by jump starting, the battery may have to be replaced.
1. Visually inspect the belt for signs of unusual wear, cuts, or fraying. If the belt is in poor condition, have it replaced or adjusted by a NISSAN dealer.
The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance log shown in the “NISSAN Service and Mainte- nance Guide.” T o remove the air cleaner filter: 1. Unlatch the clips and move the air cleaner cover upward.
CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer fluid or a mild detergent.
If you wax the surface of the hood, be careful not to let wax get into the washer nozzle 䊊 A . This may cause clogging or improper windshield-washer operation. If wax gets into the nozzle, remove it with a needle or small pin 䊊 B . If the brakes do not operate properly , have the brakes checked by a NISSAN dealer.
T wo types of fuses are used. T ype 䊊 A is used in the fuse boxes in the engine compartment. T ype 䊊 B is used in the passenger compartment fuse box. T ype A fuses are provided as spare fuses. They are stored in the passenger compartment fuse box.
NO TE: For checking and replacing fuses on QR25DE engine models, see a NISSAN dealer. If any electrical equipment does not come on, check for an open fuse. 1. Be sure the ignition switch and the headlight switch are OFF . 2. Open the engine hood. 3. Remove the fuse box cover by pushing the tabs 䊊 A and lifting the cover up from the front 䊊 B .
P ASSENGER COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire. If any electrical equipment does not operate, check for an open fuse. 1.
Extended storage switch (if so equipped) If any electrical equipment does not operate, remove the extended storage switch and check for an open fuse. NO TE: The extended storage switch is used for long term vehicle storage. Even if the ex - tended storage switch is broken it is not necessary to replace it.
KEYFOB (if so equipped) Replace the battery in the keyfob as follows: 䊊 1 Open the lid using a coin 䊊 A . 䊊 2 Remove the battery 䊊 B . 䊊 3 Install a new battery 䊊 C with the “+” facing down. ● Hold the battery by the edges. Holding the battery across the contact points will seri- ously deplete the storage capacity .
FCC Notice: Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user’s authority to op- erate the equipment.
4. Close the lid securely as illustrated 䊊 C 䊊 D . 5. Operate the buttons to check the operation. See a NISSAN dealer if you need assistance for replacement.
Fog may temporarily form inside the lens of the exterior lights in the rain or in a car wash. A temperature difference between the inside and the outside of the lens causes the fog. This is not a malfunction. If large drops of water collect inside the lens, contact a NISSAN dealer.
1. Front map lights (if so equipped) 2. Interior light 3. Headlight assembly 4. Front fog light (if so equipped) 5. High-mounted stop light (if so equipped) 6.
Use a cloth 䊊 1 to protect the interior light hous- ing. Use a cloth 䊊 A to protect the light housing. If you have a flat tire, see “Flat tire” in the “In case of emergency” section of this manual.
Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long dis- tance trips. The recommended tire pres- sure specifications are shown on the F .M.V .S.S./C.M.V .S.S. certification label or the Tire and Loading Information label under the “Cold Tire Pressure” heading.
Tire and loading information label 䊊 1 Seating capacity: The maximum num- ber of occupants that can be seated in the vehicle. 䊊 2 V ehicle load limit: See “V ehicle load- ing information” in the “T echnical and consumer information” section.
Checking tire pressure 1. Remove the valve stem cap from the tire. 2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem side- ways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage.
TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information iden- tifies and describes the fundamental characteristics of the tire and also pro- vides the tire identification number (TIN) for safety standard certification.
䊊 2 TIN (Tire Identification Number) for a new tire (example: DO T XX XX XXX XXXX) 1. DO T : Abbreviation for the “Depart- ment Of T ransportation”. The symbol can be placed above, below or to the left or right of the Tire Identification Number.
䊊 7 The word “radial” The word “radial” is shown if the tire has radial structure. 䊊 8 Manufacturer or brand name Manufacturer or brand name is shown.
For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires.
Wheel nut tightening torque: 83 ft-lb (113 N·m) The wheel nuts must be kept tight- ened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval. WARNING ● After rotating the tires, check and adjust the tire pressure.
Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in “Wheels and tires” in the “T echnical and consumer information” section of this manual.
Care of wheels ● W ash the wheels when washing the vehicle to maintain their appearance. ● Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed. ● Do not use abrasive cleaners when washing the wheels.
MEMO 8-42 Maintenance and do-it-yourself I n f o r m a t i o n P r o v i d e d b y :.
9 T echnical and consumer information Capacities and recommended fuel/lubricants .........9 - 2 Fuel recommendation ...........................9 - 4 Engine oil and oil filter recommendations ..........9 - 6 Air conditioner system (if so equipped) refrigerant and oil recommendations .
The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity.
Capacity (Approximate) Recommended Fluids and Lubricants US measure Imp measure Liter Multi-purpose grease ———N L G I N o . 2 (Lithium Soap base) Air conditioning system refrigerant — — — .
FUEL RECOMMENDA TION MR20DE and QR25DE engine except Spec-V Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91) . QR25DE engine Spec-V only Use unleaded premium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) num- ber (Research octane number 96) .
● If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol) . It should also contain a suitable amount of appropriate cosolvents and corro- sion inhibitors.
ENGINE OIL AND OIL FIL TER RECOMMENDA TIONS Selecting the correct oil It is essential to choose the correct grade, quality and viscosity engine oil to ensure satisfactory engine life and performance. See “Capacities and recommended fuel/lubricants” earlier in this section.
Y our engine was filled with a high-quality engine oil when it was built. Y ou do not have to change the oil before the first recommended change interval.
ENGINE Model MR20DE QR25DE T ype Gasoline, 4-cycle, DOHC Gasoline, 4-cycle, DOHC Cylinder arrangement 4-cylinder, inline 4-cylinder, inline Bore x Stroke in (mm) 3.307 x 3.547 (84.0 x 90.1) 3.5 x 3.9 (89.0 x 100.0) Displacement cu in (cm 3 ) 121.86 (1,997) 151.
WHEELS AND TIRES Wheel type Size Offset in (mm) Steel 15 x 6.5JJ 1.77 (45) Aluminum and steel 16 x 6.5JJ 1.77 (45) Aluminum 17 x 7.0JJ 1.97 (50) Tire size P205/60R15 P205/55R16 P225/45VR17 P225/45WR17 Spare tire T125/70D16 DIMENSIONS AND WEIGHTS Unit: in (mm) Model MR20DE QR25DE Overall length 179.
When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline.
F .M.V .S.S./C.M.V .S.S. CERTIFICA TION LABEL The Federal/Canadian Motor V ehicle Safety Standard (F .M.V.S.S./C.M.V .S.S.) certification la- bel is affixed as shown.
EMISSION CONTROL INFORMA TION LABEL The emission control information label is at- tached to the underside of the hood as shown. TIRE AND L OADING INFORMA TION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown.
Use the following steps to mount the front license plate: 䊊 1 Slide the metal mounting clips onto the li- cense plate holder as indicated. 䊊 2 Attach the license plate bracket on the plas- tic finisher at the location mark (small dimple) using the two 6mm screws provided.
● GVW (Gross V ehicle Weight) - curb weight plus the combined weight of passengers and cargo. ● GVWR (Gross V ehicle W eight Rat- ing) - maximum total combined weight of the unloaded vehicle, pas- sengers, luggage, hitch, trailer tongue load and any other optional equipment.
Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle.
WARNING Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and perfor- mance and may lead to accidents. CAUTION ● Do not tow a trailer or haul a heavy load for the first 500 miles (800 km) . Y our engine, axle or other parts could be damaged.
T emperature conditions can also affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automati- cally decrease engine power.
T owing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load.
Always verify that available capacities are within the required ratings. T OWING L OAD/SPECIFICA TION T OWING LOAD / SPECIFICATION UNIT : lb (kg) MAXIMUM T OWING L OAD *1 1,000 (454) MAXIMUM T ONGUE L OAD 100 (45) *1: The towing capacity values are calculated assuming a base vehicle with driver and any options required to achieve the rating.
Y ou may add Class I trailer hitch equipment that has a 2,000 lb (909 kg) maximum weight rating to the vehicle, but your vehicle is only capable of towing the maximum trailer weights shown in the T owing Load/Specification chart earlier in this section.
WARNING Never connect a trailer brake system di- rectly to the vehicle brake system. Pre-towing tips ● Be certain your vehicle maintains a level position when a loaded and/or unloaded trailer is hitched.
T o drive away: 1. Start the vehicle. 2. Apply and hold the brake pedal. 3. Shift the transmission into gear. 4. Release the parking brake. 5. Drive slowly until the vehicle and trailer are clear from the blocks. 6. Apply and hold the brake pedal. 7. Have someone retrieve and store the blocks.
● Some states or provinces have specific regulations and speed limits for vehicles that are towing trailers. Obey the local speed limits. ● Check your hitch, trailer wiring harness con- nections, and trailer wheel lug nuts after 50 miles (80 km) of travel and at every break.
DO T (Department of T ransportation) Quality Grades: All passenger car tires must conform to federal safety requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
Y our NISSAN vehicle is covered by the following emission warranties: For USA 1. Emission Defects Warranty 2. Emissions Performance Warranty Details of this warranty may be found with other vehicle warranties in your W arranty Information Booklet which comes with your NISSAN vehicle.
Additional information concerning motor vehicle safety may be obtained from T ransport Canada’s Road Safety Informa- tion Centre at 1-800-333-0371 or online at www.tc.gc.ca/roadsafety (English speakers) or www .tc.gc.ca/securiteroutiere (French speakers) .
These data can help provide a better understand- ing of the circumstances in which crashes and injuries occur. NO TE: EDR data are recorded by your vehicle only if a nontrivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.
Using Genuine NISSAN Parts can help protect your personal safety , preserve your warranty pro- tection and maintain the resale value of your vehicle. And if your vehicle was leased, using Genuine NISSAN Parts may prevent or limit un- necessary excess wear and tear expenses at the end of your lease.
MEMO 9-30 T echnical and consumer information I n f o r m a t i o n P r o v i d e d b y :.
10 Index A Air bag (See supplemental restraint system) .................... .1-41 Air bag system Front (See supplemental front impact air bag system) .............. .1-48 Side and curtain (See supplemental side air bag and curtain side-impact air bag system) .
Cold weather driving ............. .5-29 Compact disc (CD) player ........ .4-34, 4-37, 4-43, 4-48 Console box .................. .2-31 Continuously V ariable T ransmission (CVT) . . .5-13 Continuously V ariable T ransmission (CVT) fluid .............
Fuel Capacities and recommended fuel/lubricants ................ .9-2 Fuel economy ............... .5-23 Fuel-filler door and cap .......... .3-25 Fuel-filler door lock opener lever ..... .3-25 Fuel gauge .................. .2-6 Fuel octane rating ...
Light Air bag warning light ........ .1-56, 2-14 Brake light (See stop light) ........ .8-29 Bulb check/instrument panel ....... .2-10 Bulb replacement ............. .8-29 Charge warning light ........... .2-11 Fog light switch .............. .2-24 Headlight and turn signal switch .
Precautions on supplemental restraint system ................... .1-41 Precautions when starting and driving . . . .5-2 Programmable features ............. .4-5 Push starting .................. .6-10 R Radio Car phone or CB radio .......... .4-63 FM/AM radio with compact disc (CD) player .
Supplemental side and curtain side-impact air bag system ................. .1-53 Switch Automatic power window switch ..... .2-35 Fog light switch .............. .2-24 Hazard warning flasher switch ...... .2-24 Headlight and turn signal switch ..... .
V ehicle security system .......... .2-17 W arning/indicator lights and audible reminders .................. .2-9 W arning labels (for SRS) ......... .1-55 W arning lights .................. .2-9 W asher switch Windshield wiper and washer switch . . .
RECOMMENDED FUEL: MR20DE and QR25DE engine except Spec-V Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91) . QR25DE engine Spec-V only Use unleaded premium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) num- ber (Research octane number 96) .
® 2011 S E NTRA OWN E R’S MAN UAL For y our safety , read car efully and keep in this v ehicle. 2011 N IS SAN SE NTRA B16-D Printing : April 2011 Publication No.
Een belangrijk punt na aankoop van elk apparaat Nissan Sentra (2011) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Nissan Sentra (2011) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Nissan Sentra (2011) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Nissan Sentra (2011) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Nissan Sentra (2011) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Nissan Sentra (2011) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Nissan Sentra (2011) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Nissan Sentra (2011) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
