Gebruiksaanwijzing /service van het product AP1720-E1 van de fabrikant Asus
Ga naar pagina of 78
Dual Intel ® Xeon 5U Rackmount Server 533MHz Front Side Bus AP1720-E1 User Guide.
ii Copyright © 2004 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a r.
iii Contents Notices ............................................................................................ v Safety information .......................................................................... vi About this guide .....................
iv Contents 2.9 Cable connections ............................................................ 2-29 2.9.1 Motherboard connections .................................... 2-29 2.9.2 SCSI backplane connections ............................... 2-30 2.10 Removable components .
v Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
vi Safety information Electrical Safety • Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged. • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
vii About this guide Audience This user guide is intended for system integrators, and experienced users with at least basic knowledge of configuring a server . Contents This guide contains the following parts: 1. Chapter 1: Product Introduction This chapter describes the general features of the AP1720-E1 server .
viii References Refer to the following sources for additional information, and for product and software updates. 1. ASUS PC-DL Deluxe motherboard user guide This manual contains detailed information about the PC-DL Deluxe motherboard.
1-1 ASUS AP1720-E1 user guide This chapter describes the general features of the barebone server . It includes sections on front panel and rear panel specifications.
Chapter 1: Product introduction 1-2 1 . 1 System package contents Check your ASUS AP1720-E1 package with the items on the following table. The package contents vary for 8-SCSI, 4-SCSI, and 4-IDE HDD configurations. Contact your dealer immediately if any of the items is damaged or missing.
ASUS AP1720-E1 barebone server 1-3 1 .2 System specif ications The ASUS AP1720-E1 is a barebone server system featuring the ASUS PC-DL Deluxe motherboard. The server supports dual Intel ® Xeon ™ processors in 604-pin sockets, and includes the latest technologies through the chipsets embedded on the motherboard.
Chapter 1: Product introduction 1-4 1 .3 F ront panel features The AP1720-E1 chassis displays a stylish front bezel with lock. The bezel covers the system components on the front panel and serves as security . Open the bezel to access the front panel components.
ASUS AP1720-E1 barebone server 1-5 1 .4 Rear panel features The rear panel includes a slot for the motherboard rear I/O ports, expansion slots, a chassis lock and intrusion switch, a vent for the system fan, and power supply module.
Chapter 1: Product introduction 1-6 1 .5 Internal featur es The barebone server system includes the basic components as shown. 1. Power supply cage 2. CD-ROM drive 3. 2 x 5.25-inch drive bays 4. first drive cage (upper) 5. second drive cage (lower) 6.
ASUS AP1720-E1 barebone server 1-7 AS4 (4-SCSI configuration) AI4 (4-IDE configuration).
Chapter 1: Product introduction 1-8 1 .6 LED information The barebone system comes with five LED indicators. Refer to the following table for the LED status description. The Power , HDD Access, and Message LEDs are visible even if the system front bezel is closed.
ASUS AP1720-E1 barebone server 2-1 This chapter lists the hardware setup procedures that you have to perform when installing or removing system components.
Chapter 2: Hardware setup 2-2 2. 1 Chassis cover The chassis features a “screwless design” that allows convenient assembly and disassembly . Simply push or slide mechanical bolts 2.1.1 Removing the side cover 1. Push up the chassis lock (blue bolt) on the rear panel to release the side cover .
2-3 ASUS AP1720-E1 barebone server 2.1.2 Installing the side cover 1. Match and insert the hooks of the cover to the elongated holes on the side of the chassis. All the six hooks (three each on the top and bottom) of the cover must properly fit the designated holes.
Chapter 2: Hardware setup 2-4 2.2 Motherboard information The barebone server comes with the ASUS PC-DL Deluxe motherboard already installed. The motherboard is secured to the chassis by nine (9) screws as indicated by circles in the illustration below .
2-5 ASUS AP1720-E1 barebone server 2.3 Central Processing Unit (CPU) The motherboard comes with dual surface mount 604-pin Zero Insertion Force (ZIF) sockets. The sockets are designed for the Intel ® Xeon ™ processors in the 604-pin package with 512KB L2 cache.
Chapter 2: Hardware setup 2-6 2. Position the CPU above the socket as shown. 3. Carefully insert the CPU into the socket until it fits in place. The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU! 4.
2-7 ASUS AP1720-E1 barebone server 2.3.2 Installing the CPU heatsink and fan CPU thermal plate This motherboard requires a thermal plate for each of the CPUs. The thermal plates are already installed underneath the motherboard when the system is shipped.
Chapter 2: Hardware setup 2-8 1. Place the heatsink with fan assembly on top of the installed CPU1. Make sure it fits the screw holes of the heatsink bracket at the bottom of the CPU socket. 2. Use a Phillips screwdriver to tighten all four screws enough to secure the heatsink in place.
2-9 ASUS AP1720-E1 barebone server 4. Make sure that the heatsink and fan assembly is stable in place and the fan power cable plug is properly connected. 5. Repeat steps 1 to 2 to install the heatsink and fan assembly for the second CPU, then connect the fan cable to the fan connector labeled CPUF AN2.
Chapter 2: Hardware setup 2-10 2.4 System memor y The motherboard comes with four Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 4GB system memory using 184-pin unbuffered ECC or non-ECC PC2700/ PC2100 DDR DIMMs, and allow up to 5.
2-11 ASUS AP1720-E1 barebone server 2.4.2 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause damage to both the motherboard and the components. 1. Unlock a DIMM socket by pressing the retaining clips outward.
Chapter 2: Hardware setup 2-12 Before you can install a 5.25-inch drive, you should first remove the front panel assembly (front bezel and front panel cover). The front panel assembly is attached to the chassis through four hooked tabs on the left side and four hinge-like tabs on the right side.
2-13 ASUS AP1720-E1 barebone server Do not use too much force when removing the front panel assembly . 3. Unhook the hinge-like tabs from the holes on the right side of the front panel to completely detach the front panel assembly from the chassis.
Chapter 2: Hardware setup 2-14 2.5.2 Re-installing the front panel assembly T o re-install the front panel assembly (front bezel and front panel cover): 1.
2-15 ASUS AP1720-E1 barebone server 2.6 5.25-inch drives Three 5.25-inch drive bays are located on the upper front part of the chassis. A CD-ROM drive that comes standard with the system package occupies the uppermost bay (labeled 1) . The two lower bays (labeled 2 and 3) are available for additional 5.
Chapter 2: Hardware setup 2-16 3. When released, pull up the drive bay lock bar . Underneath the lock bar are two pegs that match the holes on the drive bay . This mechanism secures the drive to the bay in place of screws. 4. While holding up the bar lock, carefully insert a 5.
2-17 ASUS AP1720-E1 barebone server 7. Make sure that the drive and bay holes align as shown. When in place, the drive protrudes about an inch from the front panel. 8. Pull down the bar lock and insert the lock pegs to the drive/bay holes, then push the drive lock to the right to secure the drive.
Chapter 2: Hardware setup 2-18 2.7 Hard disk drives 2.7.1 Installing a hot-swap SCSI HDD T o install a SCSI hard disk drive: 1. Open the front bezel to access the hot-swap drive trays. 2. Release a drive tray by pushing the spring lock to the right, then pulling the tray lever outward.
2-19 ASUS AP1720-E1 barebone server 5. Place an SCA SCSI hard disk into the drive tray , and secure it with four screws. 6. Carefully insert drive tray and push it all the way to the depth of the bay until just a small fraction of the tray edge protrudes.
Chapter 2: Hardware setup 2-20 2.7.2 Installing an IDE HDD If your system is an IDE model, your package comes with specially designed hard disk drive rails. Depending on which bay you wish to install your hard disk drive, the orientation of the drive rails vary so that the screw holes match those on the drive.
2-21 ASUS AP1720-E1 barebone server 3. Attach Rail 2 to the other side of the drive as shown. The rail end should be on the side of the drive connectors. Drive connectors Hole 1 Hole 3 Rail end 5. Carefully insert the drive into a bay on the front panel.
Chapter 2: Hardware setup 2-22 Installing into a bay on the second drive cage T o install an internal drive : 1. Remove the side cover . Refer to section 2.1.1 for instructions. 2. Use a Phillips (cross) screwdriver to attach Rail 2 to the side of the drive with two screws as shown.
2-23 ASUS AP1720-E1 barebone server 5. Carefully insert the drive into a bay on the second drive cage as shown. 6. Connect the IDE and power cables to their corresponding connectors on the back of the drive. 4. Check the HDD jumper setting. Refer to the label pasted on the HDD for the setting description.
Chapter 2: Hardware setup 2-24 2. Press the dummy cover into the slot opening until the hook tab clicks in place. 3. When installed, the dummy cover appears as shown. Installing an HDD dummy cover Except on the 8-SCSI configuration model (AS8), the HDD dummy covers come pre-installed on the front panel bezel.
2-25 ASUS AP1720-E1 barebone server 2.8 Expansion cards The chassis is designed with a screwless expansion slot frame on the rear panel. This design feature allows you to install or remove an expansion card in less steps. Make sure to unplug the power cord before installing or removing expansion cards.
Chapter 2: Hardware setup 2-26 3. When the card is in place, secure it with the plastic card lock that you removed earlier . Card lock tab.
2-27 ASUS AP1720-E1 barebone server 3. When the card is inside the chassis, push down the end of the card until it is level with the PCI slot. 2.8.2 Installing a long expansion card If you wish to ins.
Chapter 2: Hardware setup 2-28 2.8.3 Removing an expansion card T o remove an expansion card: 1. Remove the plastic card lock that secures the expansion card. 2. Firmly hold the expansion card and pull it out of the slot. 3. Place the plastic card lock back where you removed it.
2-29 ASUS AP1720-E1 barebone server 2.9 Cable connections The bundled system cables are pre-connected before shipment. Y ou do not need to disconnect these cables unless you will remove pre- installed components to install additional devices. Refer to this section when reconnecting cables to ensure correct cable connections.
Chapter 2: Hardware setup 2-30 2.9.2 SCSI backplane connections The SCSI backplane has four 68-pin SCSI connectors to support SCA SCSI hard disks. The backplane design incorporates a hot swap feature to allow easy connection or removal of SCSI hard disks.
2-31 ASUS AP1720-E1 barebone server Back side The back side of SCSI backplane faces the rear panel when installed. This side includes the power connectors, SCSI interfaces for the SCSI/RAID card and terminator , and SMBus connectors. The following picture shows a two-backplane configuration in a cascade connection.
Chapter 2: Hardware setup 2-32 One-backplane configuration In a one-backplane configuration: • the upper SCSI interface of the backplane connects to the SCSI/RAID card • a SCSI multi-mode terminat.
2-33 ASUS AP1720-E1 barebone server T wo-backplane configuration In a two-backplane configuration: • the upper SCSI interface of the first backplane connects to the SCSI card • the lower SCSI inte.
Chapter 2: Hardware setup 2-34 SCSI backplane jumper settings and HDD ID assignments The 6-pin jumper J1 on each of the SCSI backplanes allows you to define your desired SCSI configuration. The picture below shows the location of jumper J1 with pins 1-3 and 2-4 shorted.
2-35 ASUS AP1720-E1 barebone server Non-Cascade configuration First backplane (BPB1) J1 setting (1-3 shorted, 2-4 shorted) Device SCSI ID# Drive Bay 1 ID0 Drive Bay 2 ID1 Drive Bay 3 ID2 Drive Bay 4 I.
Chapter 2: Hardware setup 2-36 2. 10 Removable components Y ou may need to remove previously installed system components when installing or removing system devices, or when you need to replace defective components. This section tells how to remove the following components: 1.
2-37 ASUS AP1720-E1 barebone server 2.10.2 HDD fans T o remove the HDD fan: 1. Loosen the thumb screw that secures the HDD fan cage to the chassis. 2. Hold the outer side of the fan cage, then pull sideways to release it from the chassis.
Chapter 2: Hardware setup 2-38 T o re-install the HDD fan: 1. Re-connect the 3-pin fan cable to the fan connector on the backplane. 3. Push the outer edge of the fan cage sideways to fit it to the drive cage. Y ou hear a click when the fan cage correctly fits in place.
2-39 ASUS AP1720-E1 barebone server 2.10.3 SCSI backplanes T o remove a SCSI backplane: 1. Remove the HDD fan cage. Refer to section “2.10.2 HDD fans” for instructions. 2. Disconnect all cables from the backplane. When disconnecting a cable, hold and firmly pull the cable plug.
Chapter 2: Hardware setup 2-40 T o re-install a SCSI backplane: 1. Position the backplane into its slot with the component side facing the rear panel, and the power connectors on top. 2. Align the backplane with the rail- like dents on the slot to ensure that it fits securely .
2-41 ASUS AP1720-E1 barebone server 2.10.4 Power supply module Y ou MUST disconnect all power cable plugs from the motherboard and other installed devices before removing the power supply . The picture below shows the motherboard and device connectors where the power plugs are connected.
Chapter 2: Hardware setup 2-42 T o remove the power supply module: 1. Loosen the thumbscrew that secures the power supply metal plate. Do not remove the thumb screw from the metal plate. Thumbscrew 2. Hold the metal plate bar and push it downward to release the plate from the chassis.
2-43 ASUS AP1720-E1 barebone server T o install a power supply module: 1. Firmly hold the power supply module and insert it into the power supply cage. 2. Push the power supply all the way in until its outer end aligns with the rear panel. Be careful with the power supply cables when inserting the power supply module into the cage.
Chapter 2: Hardware setup 2-44 2.10.5 Floppy disk drive 2. Carefully pull out the drive from the chassis until you see the cables connected to the drive. T o remove the floppy disk drive: 1. Remove the screw that secures the drive to the chassis. Y ou need to remove the front panel assembly before you can remove the floppy disk drive.
2-45 ASUS AP1720-E1 barebone server T o install a floppy disk drive: 1. Position the floppy drive vertically with the eject button on the left side (close to the HDDs). 2. Connect the drive signal cable and power cable. 4. Secure the drive cage with a screw .
Chapter 2: Hardware setup 2-46 2.10.6 Front I/O board Y ou need to remove the front panel assembly before you can remove the front I/O board. Refer to section “ 2.5.1 Removing the front panel assembly ” for instructions. T o remove the front I/O board: 1.
2-47 ASUS AP1720-E1 barebone server T o install the front I/O board: 1. Place the I/O board in the bracket, component side up. Secure the front I/O board to the bracket with a screw . 2. Position the I/O board into the bay with the component side to the left (close to the HDDs).
Chapter 2: Hardware setup 2-48 2.10.7 Chassis footpads and roller wheels The barebone server system is shipped with four footpads attached to the bottom of the chassis for stability .
2-49 ASUS AP1720-E1 barebone server T o remove the chassis wheels: 1. Lay the system chassis on its side. 2. Use a Phillips screwdriver to remove the screws that secure the wheels to the bottom of the chassis. 3. Repeat step 2 to remove the other three roller wheels.
Chapter 2: Hardware setup 2-50.
3-1 ASUS AP1720-E1 barebone server This chapter describes how to install optional components and devices into the barebone server and create your desired configuration.
Chapter 3: Installation options 3-2 3. 1 Installing a second SCSI dr ive cage Perform this installation if you wish to upgrade your 4-SCSI configuration system (AS4 model) to an 8-SCSI configuration. The items required for the optional configurations described in this chapter are not included in the standard barebone system package.
3-3 ASUS AP1720-E1 barebone server 3. Make sure that the cage lock tab snaps to the bottom of the first drive cage. When properly installed, the cage should align with the first drive cage. Cage lock tab snapped securely to the bottom of first drive cage 4.
Chapter 3: Installation options 3-4 5. Insert the tabs into the holes. Y ou may need to swing the bracket a bit from left to right and back to fully insert the tabs. 6. When the tabs are fully inserted in the holes, swing the bracket to the right until one side is flat to the chassis.
3-5 ASUS AP1720-E1 barebone server 3.2 Installing an IDE dr ive cage Perform this installation if you wish to upgrade your 4-SCSI configuration system (AS4 model) to a combination 4-SCSI/4-IDE configuration. 4-SCSI configuration 4-SCSI/4-IDE configuration T o install an IDE drive cage: 1.
Chapter 3: Installation options 3-6 3. Make sure that the drive cage is fits snugly to the bay as shown. The drive cage is properly installed when it is parallel to the front panel, and the screw hole matches the hole of the first drive cage. Screw hole 4.
3-7 ASUS AP1720-E1 barebone server 3.3 Mounting the system to a rac k 3.3.1 Remove the footpads or roller wheels Refer to section “2.10.7 Chassis roller wheels and footpads” for instructions on removing the footpads or roller wheels. 3.3.2 Remove the top cover T o remove the top cover: 1.
Chapter 3: Installation options 3-8.
3-1 ASUS AP1720-E1 barebone server This appendix gives information on the power supply that came with the barebone server . Appendix Power supply.
Chapter 3: Installation options A-2 A. 1 General descr iption The server comes with an SSI-type 450W A TX power supply with universal AC input that includes PFC and A TX-compliant output cables and connectors. The power supply has nine plugs labeled P1 to P10 (no P3).
A-3 ASUS AP1720-E1 barebone server A.2 Specifications Output voltage regulation Output current capacity Over-voltage protection V oltage Min (V) Max (V) +3.33V 3.9 4.5 +5V 5.7 6.5 +12V 13.3 15.0 +12V -13.3 -15.0 +5VSB 5.7 6.5 Output V oltage Min (A) Max (A) Max.
Chapter 3: Installation options A-4.
Een belangrijk punt na aankoop van elk apparaat Asus AP1720-E1 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Asus AP1720-E1 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Asus AP1720-E1 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Asus AP1720-E1 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Asus AP1720-E1 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Asus AP1720-E1 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Asus AP1720-E1 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Asus AP1720-E1 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
