Gebruiksaanwijzing /service van het product TT-1650 van de fabrikant Numark Industries
Ga naar pagina of 16
TT-1650 Operating Instructions (1) TT-1650 Turntable (1) Aluminum Platter (1) IEC Power Cable (1) RCA Cord w/ Ground Wire (1) Slipmat INSIDE THE BOX: (1) Headshell w/ Cartrdige (1) Counter Weight.
PAGE 1 SAFETY PRECAUTIONS Thank you for buying this Numark product. Please read these operating instructions so you will know how to oper ate this equipment properly . After you have finished reading these instructions, k eep them for future reference.
PAGE 2 T ABLE OF CONTENTS IMPORT ANT The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
PAGE 3 CONTROLS CONTROLS General Controls 1. Power Button Pushing this button down turns on the turntable. 2. Start/Stop Buttons These buttons start and stop the turntable motor . Both buttons ha ve the same function. 3. Platter This turntable has a special edge design that has been optimized for "dr agged" platter slow downs.
PAG E 4 CONTROLS CONTROLS continued Tone Arm Parts 7. Counter W eight and Scale Ring The Counterweight is used to balance the head shell and cartridge assembly so that the proper amount of stylus pressure is applied to the record. 8. Anti-Skate Adjustment This knob is used to compensate for inward tr acking forces.
PAGE 5 SETUP & INSTALLATION This turntable has been designed exclusively for DJ use and can be setup in a v ariety of different wa ys depending on your mixing style. The turntable should rest on a level and stable surface that is clear of obstructions.
PAGE 6 PLA T TER SETUP 1. Locking Pins 3. ALIGNED PLATTER SETUP WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instabilit y or permanent motor damage. 1. Start by inspecting the bottom of the aluminum platter to check that both locking pins have rubber fittings on them.
PAGE 7 CABLE SETUP CABLE SETUP This turntable is shipped with two sets of special cables: (1) Right Angle IEC Power Cord (1) Right Angle RCA cord w/ground wire NOTE: Before connecting an y cables, make sure that the voltage selector switch is set to the proper setting, either 110V or 220V depending on region.
PAGE 8 TONE ARM SETUP TONE ARM SETUP A properly adjusted tone arm and cartridge setup will minimize vinyl record wear and optimize the performance of the turntable. Follow these simple steps for setting the tone arm on the turntable: Balancing the Tone Arm 1.
PAGE 9 CARTRIDGE SETUP CARTRIDGE SETUP For Head Shell Mounted Cartridges: The cartridge that comes with this turntable should be preinstalled on the head shell. If it isn't, please follow the below instructions for installing a cartridge onto the head shell.
OPERA TION PAGE 10 OPERATION This turntable was designed to accommodate a v ariety of different mixing styles. Here are some general operation guidelines to optimize the performance of the turntable. 1. Do not place the turntable on or near a speaker or subwoofer .
PAGE 11 WARRANTY LIMITED PRODUCT WARRANTY 1. What is covered and for how long? NUMARK INDUSTRIES LCC ("NUMARK") w arrants to the original purchaser that NUMARK'S products; including but.
PAGE 12 RETURN INFORMA TION RETURN INFORMATION (US ONL Y) a) A Return A uthorization number must be obtained from Numark through the address or phone numbers below. b) A copy of the original sales receipt must also be included for the equipment to be repaired under warr anty .
PAGE 13 SPECIFICA TIONS SPECIFICATIONS Turntable Section: T ype: 2 speed, fully manual Motor: Direct Drive Starting T orque: > 1 Kg/cfm Platter: Aluminum Diecast Speed: 33.
TROUBLE SHOOTING PAGE 14 T urntable does not turn on. Disconnected Power Cord? Connect Power Cord. The sound level is very low . The T urntable is not connected to a device with a PHONO preamp. Connect the device to a preamp DJ mixer or an A V receiver that has an input labeled PHONO, not AUX or LINE.
Copyright Numark Industries, LLC 2002 T T -1600, T T -1650 Manual /English - rev B.
Een belangrijk punt na aankoop van elk apparaat Numark Industries TT-1650 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Numark Industries TT-1650 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Numark Industries TT-1650 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Numark Industries TT-1650 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Numark Industries TT-1650 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Numark Industries TT-1650 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Numark Industries TT-1650 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Numark Industries TT-1650 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
