Gebruiksaanwijzing /service van het product LDN-PS van de fabrikant Omega Vehicle Security
Ga naar pagina of 28
omega.com e-mail: info@omega.com For latest product manuals: omegamanual.info U ser ’ s Guide LDN-PS Shop online at solartron 6 9 5 1.
Servicing North America: USA: One Omega Drive, Box 4047 ISO 9001 Certified S tamford CT 06907-0047 T el: (203) 359-1660 F AX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada T el: (514) 856-6928 F AX: (514) 856-6886 e-mail: info@omega.
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 2 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . .3 Service Safety . . . . . . .
PSIM-AC PSIM-DC PSIM-5V Introduction The Power Supply Interface Module (PSIM) is part of the Orbit Measurement System. The PSIM provides local power to the network when required. Example uses: • Power via the communications cable is not suf ficient due to cable voltage drop s.
This equipment is designed as safety Class 1 apparatus to comply with EN61010-1. Service Safety This equipment has been designed and tested to meet the requirements of the Low V oltage Directive (1997) and has been supplied in a safe condition.
W ARNING: Danger arising from loss of ground. During a fault condition and upon loss of protective ground (earth), all accessible conducting part s - including controls that might appear to be insulated - can render an electric shock. W ARNING: Grounding the equipment.
3.0: General Information PSIM-AC PSIM-DC PSIM-5V LDN-PS 6 M-3340/1206 6 9 51 Power Supply OUTPUT PSIM V ariant s 6 9 51 Power Supply OUTPUT 6 9 51 Power Supply OUTPUT PSIM-AC T o power Orbit Modules f.
LDN-PS 7 M-3340/1206 3.0: General Information (continued) PSIM-AC PSIM-DC PSIM-5V PSIM General Layout PSIM 911173 1 7 3 A 1 2 3 R 0 1 6 9 5 1 Power Supply OUTPUT 6 9 51 Power Supply OUTPUT *Cable Lengths • PSIM-AC and PSIM-DC have a fixed 2m cable between PIE and power supply .
PSIM used in a small network configuration 3.0: General Information (continued) PSIM-AC PSIM-DC PSIM-5V LDN-PS 8 M-3340/1206.
4.0: PSIM Schematic and Pin-out The 5V power supply line from the network is isolated at the PSIM. All modules before the PSIM are powered from the network. Example: Orbit Network Card. All modules after the PSIM are powered from the external power supply connected via the PSIM.
4.0: PSIM Schematic and Pin-out (continued) The PSIM will only supply power to the Orbit Modules that follow the PSIM. Some typical configurations are shown. For more information about PSIM and Orbit Network connection, refer to the Applications section.
5.1 Power Supply The mounting plate must not be removed. The mounting plate is isolated and does not need to be at earth potential. The power supply may be mounted in any orientation. The power supply must not be exposed to fluids or excessive dust. Power supply cooling is by convection; allow room for air to flow around the unit.
PSIM-AC PSIM-DC PSIM-5V 5.0: Dimensions and Mechanical Inst allation (continued) 5.2 PSIM T -CON is permanently att ached, module does not separate. For more information on mounting, refer to the Orbit Measurement System Manual.
PSIM-AC PSIM-DC PSIM-5V 6.0: S pecification Input V olt age 85 to 264 V ac @ 47 Hz to 440 Hz. Current 0.8 A Connection via IEC320 connector Isolation 2500 V ac input/output Protection Input fuse and filter (not user replaceable) Recommended Line Fuse 2A T (slo-blo) 250 V rating DC Output Output V olt age 5.
6.0: S pecification (continued) PSIM-AC PSIM-DC PSIM-5V Input Line V olt age 10 to 30 Vdc. Current 1.1 A @ 12 Vdc; 0.5 A @ 24 Vdc (nominal). Connection see note 3 5m flying lead (Red = positive, White.
6.0: S pecification (continued) PSIM-AC PSIM-DC PSIM-5V Line V olt age see note 1 5.1 Vdc Nominal as supplied by user 5.25 Vdc MAX Input Current 1.8 A MAX Connection see note 3 5m flying lead (Red = p.
6.0: S pecification (continued) PSIM-AC PSIM-DC PSIM-5V Environment al Operational temperature 0 to 60 °C S torage temperature -20 to 60 °C Humidity 5% to 95% non-condensing Cooling Convection Prote.
Orbit Network Power Supply Requirement s All Orbit Modules are designed to work from a supply voltage of 4.75V to 5.25 Vdc. When power is applied to a module its current consumption will cause a slight voltage drop across cables. Care must be t aken to ensure that all modules have the right working voltage applied.
7.0: Applications (continued) V olt age Drop Estimation The following information is for guidance only when planning an installation. V oltage measurements must still be made to ensure the right working voltage for each Orbit Module. 6 9 51 Power Supply OUTPUT PSIM-AC PSIM-DC PSIM-5V PSIM-AC PSIM-DC see note 1 volt drop (from no load output) V = 5.
PSIM-AC PSIM-DC PSIM-5V 7.0: Applications (continued) Application 1: Basic Small Network Connection. • Power supplied to network from PC via network card, no PSIM used. • Modules connected using standard communication cables. V olt drop tot al in mV = cable 1 + module (3 of f) + cable 2 + module (3 off) = (15.
PSIM-AC PSIM-DC PSIM-5V 7.0: Applications (continued) Application 2: Large network with modules close to computer and at a dist ance. • Power supplied from PC and PSIM (located at a distance from PC). • Communications via standard communications cable and custom cable.
PSIM-AC PSIM-DC PSIM-5V 7.0: Applications (continued) V olt drop V 1 is calculated in a similar way to the previous example except there is only a single cable and 3 Orbit modules. The PSIM supplies power to remaining modules and are calculated separately .
PSIM-AC PSIM-DC PSIM-5V 7.0: Applications (continued) Application 3: Large Network using PSIM-5V and RS232IM for network control. LDN-PS 22 M-3340/1206.
PSIM-AC PSIM-DC PSIM-5V The PSIM-5V is powering the whole Orbit Network. PSIM-5V volt drop is calculated using 12 as the total number of Orbit modules; the RS232IM is included in this number . T otal V oltage drop = PSIM-5V + modules (6 of f) + Cable 1 + Modules (6 of f) = (2 x 12 x [3+1]) + 0.
PSIM-AC PSIM-DC PSIM-5V 7.0: Applications (continued) Application 4: Modules located a long dist ance from computer . • Also for a computer that is not suit able for supplying power to Orbit Modules. • Power supplied from PSIM to modules. • Connection via long cable providing RS485, 0V reference and screening.
7.0: Applications (continued) PSIM-AC PSIM-DC PSIM-5V Application 5: Use with RS232 Interface Module (RS232IM). • Communication is via a RS232IM. • Power to the RS232IM and Orbit Modules is via PSIM.
M-3340/1206 W ARRANTY / DISCLAIMER OMEGA ENGINEERING , INC. warrant s this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA ’s W arranty adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time.
Where Do I Find Everything I Need for Process Measurement and Control? OM EGA…Of Course! Shop online at www .omega.com M-3340/1206 TEMPERA TURE Thermocouple, RTD & Thermistor Probes, Connect.
Een belangrijk punt na aankoop van elk apparaat Omega Vehicle Security LDN-PS (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Omega Vehicle Security LDN-PS heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Omega Vehicle Security LDN-PS vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Omega Vehicle Security LDN-PS leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Omega Vehicle Security LDN-PS krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Omega Vehicle Security LDN-PS bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Omega Vehicle Security LDN-PS kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Omega Vehicle Security LDN-PS . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
