Gebruiksaanwijzing /service van het product R-801A van de fabrikant Onkyo
Ga naar pagina of 52
TUNER AMPLIFIER R-801A Instruction Manual Before using Connections Preparations Operation Other Information English DISPLAY R - 8 01 A STANDBY / ON STANDBY INPUT ACOUSTIC PRESENCE TUNING MEMORY FM MODE CLEAR PHONES TUNER AMPLIFIER VOLUME Thank you for purchasing the ONKYO R-801A T uner Amplifier .
2 Important Safeguar ds 1. Read Instructions – All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions – The safety and oper- ating instructions should be retained for future reference.
3 14. Outdoor Antenna Grounding – If an out- side antenna or cable system is connected to the appliance, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
4 Pr ecautions 1. Recording Copyright Recording of copyrighted material for other than personal use is illegal without permis- sion of the copyright holder . 2. AC Fuse The fuse is located inside the chassis and is not user-serviceable. If power does not come on, contact your Onkyo authorized service station.
5 For U.S. model Note to CA TV system installer: This reminder is provided to call the CA TV system installer’ s attention to Article 820-40 of the NEC, ANSI/NFP A 70, which provides guidelines for .
6 Main Featur es • A compact, discrete component with 155mm (6-1/8") wide • 24 W atts per channel into 4 ohms DIN • Low impedance drive discrete output stage • Accoustic Presence • RDS .
7 T able of contents Before using Supplied accessories ........................................................................................................... .6 Connections Connecting to the ONKYO Separate Collection Series components ...........
8 Connecting to the ONKYO Separate Collection Series components This section introduces you to the other Separate Collection Series system components and their convenient system functions, followed by connecting instructions. The following Separate Collection Series components are commercially available: • C-701A .
9 Combination example 1 Select the CD player C-701A and CD recorder in addition to this unit. When you arrange these components, stack them as shown below . V ertical way stacking Horizontal way stacking Combination example 2 Select the CD player C-701A, CD recorder and MD recorder MD-101A in addition to this unit.
10 Connecting to the ONKYO Separate Collection Series components Before connecting • Do not connect the unit ’ s AC power cord (mains lead) to a wall outlet (the mains) until you have completed all the other connections, including and AC OUTLET connections on page 12 and “ Connecting speaker systems ” on page 16.
11 Note: T o connect both the MD recorder MD-101A and CD player C-701A to the unit: Connect the MD recorder to the unit following the “ Connection for combination example.
12 Connecting to the ONKYO Separate Collection Series components Before connecting • The hookups on page 11 is needed in addition to the (for remote control operations) and AC OUTLET (for power supply to each component) hookups on this page. • Each component has two connectors.
13 Connecting to components other than the Separate Collection Series Before connecting • Do not connect the AC power cord (mains lead) to the wall outlet (the mains) until you have completed all the other connections including the sound processor connections on the next page, the connections on page 15, and the speaker connections on page 16.
14 Connecting to components other than the Separate Collection Series Before connecting • If your subwoofer isn ’ t equipped with an ampli fi er , connect a separate ampli fi er to the unit fi rst, then connect the subwoofer to that ampli fi er .
15 If your other components are made by ONKYO and those components are equipped with connectors, you can control the -connected components with the supplied remote control- ler . Before connecting • The unit must be connected in the system hookups for control operations.
16 Connecting speaker systems Before connecting • The load impedance of each speaker must be at least 4 ohms. • Do not use unnecessarily long or extremely thin speaker cords. Otherwise, the DC resis- tance of the speaker cords may become too high, lowering the damping factor and causing the sound quality to deteriorate.
17 Antenna connections Assembling the AM loop antenna Assemble the loop antenna as shown in the illustration. Connecting the antenna cable Connecting the AM loop antenna The AM loop antenna is for indoor use only . Set it in the direction and position where you receive the clearest sound.
18 Antenna connections FM indoor antenna The supplied FM antenna is for indoor use only . Move the antenna in various directions until the clearest signal is received. Fix it with push pins or similar implements in the position that will cause the least amount of distortion.
19 Connecting the 300 ohm ribbon wire: Connecting the coaxial cable: 1. With your fi ngernail or a small screw- driver , press the stoppers outward and remove the cover . 2. Remove the transformer wire A from slit B and insert it into slit C. 3. Prepare the coaxial cable as shown in the diagram.
20 Pr eparing the r emote contr oller 1 Remove the battery compartment cover by pressing and sliding it away from the remote contr oller unit. 2 Insert two AA-size batteries into the battery compartment. Carefully follow the polarity diagram (positive + and negative - symbols) inside the battery compartment.
21 Connecting the AC power cor d (mains lead) . Notes • If the AC power cord (mains lead) is con- nected to the AC outlet of another com- ponent, that component ’ s AC power cord (mains lead) must be connected to the wall outlet (the mains) to supply power to the unit.
22 Setting the Clock The ” ACCUCLOCK “ features an automatic clock adjusting function automatically sets the clock time by means of RDS broadcast signals. • The “ ACCUCLOCK ” feature is available only on the European model, and only in areas where RDS broadcasts are available.
23 If you wish to know which RDS station has been used to set the clock by ACCUCLOCK, or to use a different RDS station signal to set the clock, follow the steps below: 1 Press the TIMER button repeatedly until “ADJUST” is selected on the dis- play , then press the ENTER button.
24 Setting the Clock • The explanation in this section assumes that the unit has been powered on (set to “ Stand-by On ” ). This section explains how to set the clock using the 24-hour display . However , you can later change this set- ting to the 12-hour display .
25 4 Use the or button or the number buttons to set the desired time. Entering the time value using the number buttons on the remote controller: T o set 9:38 am, press 10/0, 9, 3, 8, then ENTER. T o set 11:00 am, press 1, 1, 10/0, 10/0, then ENTER. * “ 10/0 ” stands for “ 0.
26 Setting the Clock 1 Press the CLOCK button to display the time, press again to cancel the time display . Note If the time has not been set, “ ADJUST ” will fl ash on the display . While the power to the unit is turned on: When you press the CLOCK button, the day/ time indicator appears.
27 Choosing the r equir ed sour ce 1 Press the INPUT button repeatedly or the INPUT SELECTOR buttons on the remote controller to select the source you wish to listen to lights. The name of the selected source appears on the display in the following order: 2 Start playing the source you selected in step 1.
28 Adjusting the sound Acoustic Presence adds realness to music through the use of exclusive Onkyo circuitry . Presence settings 1, 2, 3 and 4 are ideally suited for use with compact speakers. Press the ACOUSTIC PRESENCE on the unit or the remote contr oller .
29 Muting/Listening with the headphones Press the MUTING button on the r emote controller to mute the sound. The MUTING indicator appears on the dis- play .
30 Recor ding Before r ecording Refer to the instruction manuals of the related components for detailed recording operations. Note Do not press the INPUT button during recording. 1 Press the INPUT button repeatedly to select the source you wish to record from lights.
31 Receiving stations 1 Select FM or AM using the INPUT but- ton or the FM or AM button on the remote controller . 2 Use the √ TUNING ® ( / ) con- trol to change the frequency . The indoor antenna should be installed on a wall or other surface in the position which gives the best reception.
32 Receiving stations 2 Use the √ TUNING ® (/) con- trol to select the fr equency of your favorite station. The indicator lights up on the display when the broadcasting station is properly tuned in. T uning in FM stations: T urn and hold the √ TUNING ® control to the left or right to start auto-tuning.
33 When you tune in a stereo FM station, the indicator lights up if the signal is suf fi - ciently strong. If the signal is weak, you can still listen to the station in mono mode. In this case, tune in as follows. 1 Press the FM MODE button. The “ AUTO ” indicator lights up.
34 Naming a pr eset station Y ou can name the preset stations so that the name, instead of the frequency , appears on the display when you press the DISPLA Y but- ton.
35 5 When you fi nish entering all neces- sary characters, press and hold down the DISPLA Y button for more than two seconds to complete the opera- tion. Note If you have not pressed any button for 16 seconds during the procedure, the operation will complete automatically .
36 Naming preset stations 4 Use the √ TUNING ® ( / ) con- trol to change the character . 5 Press the MEMOR Y button to store the character . 6 Press and hold down the DISPLA Y but- ton for more than two seconds to complete the operation. Follow the procedure below to delete the name of the selected preset station.
37 Receiving RDS (Eur opean models only) RDS reception is available only on the Euro- pean model, and only in areas where RDS broadcasts are available.
38 Using the timer The R-801A features a T imer function that enables you to start playing or recording a speci fi ed component at a speci fi ed time. T o use this function, you need to connect this unit to other components via REMOTE CONTROL jacks.
39 Y ou can de fi ne or change which day is WEEK- DA Y or WEEKEND. Y ou can also de fi ne the day as both WEEKDA Y and WEEKEND in order to program two timer settings on the same day .
40 Using the timer Before using the timer for listening to or recording broadcast programs, you need to store the preset stations. (Refer to “ Receiv- ing stations ” on page 31, 32 for information how to preset stations.) 1 Press the TIMER button repeatedly until “ W .
41 If you select an input source that is not connected to the R-801A, the power is turned on to the unit at the programmed time and the input source is switched, but nothing will happen. 5 Press the ST ANDBY/ON button on this unit to set the Standby mode.
42 Using the timer 3 Press the or button to set the ON time, and press the ENTER button. Notes • Y ou can also use the number buttons instead of the or button to set the desired recording ON and OFF time. T o do so, refer to step 3 on page 24 and select the 24-hour display .
43 7 Press the ST ANDBY/ON button on this unit to set the Standby mode. Note Since muting is automatically turned on when the timer is used to record, the sound cannot be heard during recording. T o moni- tor recording, press the MUTING button on the remote controller to cancel muting.
44 Using the timer The Sleep function can be performed only by using remote controller . The SLEEP timer automatically sets the entire system to Standby mode after a speci fi ed period of time. 1 Start playing something you would like to listen to. (CD, tape, MD or radio broadcast).
45 Index to parts and contr ols For more information about buttons, turn to the page number in the brackets [ ]. Front panel DISPLAY R - 8 01 A STANDBY / ON STANDBY INPUT ACOUSTIC PRESENCE TUNING MEMO.
46 Index to parts and controls • Y ou can control the other -connected components with the supplied remote controller . • The remote controller buttons operate in the same way as the buttons on each component with the same indication. For actual operations, please refer to the Instruction Manual for each component.
47 Use the following buttons to control components that are connected to the - system. • Buttons marked with an asterisk (*) can be used to control components that ar e con- nected to the - system. For actual operations, please refer to the Instruction Manual for each component.
48 T r oubleshooting If you have any problems with the unit, please check the troubleshooting table below fi rst. For any problems not covered in the table, please consult your nearest ONKYO authorized service center . Symptom Cause Remedy The unit doesn ’ t turn on.
49 • Excessive electrical interference may temporarily render this system ’ s sensitive microcom- puter inoperable. If this happens, unplug the system for at least fi ve seconds. Symptom Cause Remedy AM stations cannot be received. • AM loop antenna is not attached.
50 Speci fi cations Ampli fi er Section Power output 17 watts per channel, min RMS, at 4 ohms, both channels driven 1 kHz, with no more than 0.8% THD 13 watt per channel, min RMS, at 8 ohms, both channels driven 1 kHz, with no more than 0.
51 General Clock precision monthly error: +/-30 seconds (at 25 degrees Celsius) Power supply AC 120 V , 60 Hz AC 230-240 V , 50 Hz AC 220-230 V , 50 Hz/60 Hz Power consumption 44 W Dimensions (W X H X D) 155 X 94 X 285 mm 6-1/8" X 3-1/16" X 11-1/4" Weight 2.
E http://www.onkyo.co.jp/ HOMEP AGE SN 29343214A I0109-2 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8111 Fax: 072-833-5222 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.
Een belangrijk punt na aankoop van elk apparaat Onkyo R-801A (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Onkyo R-801A heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Onkyo R-801A vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Onkyo R-801A leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Onkyo R-801A krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Onkyo R-801A bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Onkyo R-801A kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Onkyo R-801A . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
