Gebruiksaanwijzing /service van het product P5Q WS van de fabrikant Asus
Ga naar pagina of 176
Motherboard P5Q WS.
ii E3771 First Edition June 2008 Copyright © 2008 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitt.
iii Contents Contents ...................................................................................................... iii Notices ........................................................................................................ vii Safety information .
iv Contents 2.5.5 PCI Express x1 slots ..................................................... 2-18 2.5.6 PCI-X slot ...................................................................... 2-18 2.5.7 PCI Express 2.0 x16 slots ............................
v Contents 3.3.3 Legacy Diskette A ........................................................ 3-12 3.3.4 Language ...................................................................... 3-12 3.3.5 SA T A 1–6 ............................................
vi Contents 4.2.2 Drivers menu ................................................................... 4-2 4.2.3 Utilities menu .................................................................. 4-3 4.2.4 Make disk menu ...................................
vii Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
viii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
ix About this guide This user guide contains the information you need when installing and conguring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports.
x Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. T ypography Bold text Indicates a menu or an item to select. Italics Used to emphasize a word or a phrase.
xi P5Q WS specications summary CPU LGA775 socket for Intel ® Core ™ 2 Extreme / Core ™ 2 Quad / Core ™ 2 Duo / Pentium ® dual-core / Celeron ® dual- core / Celeron ® processors Intel ® EM64T / EIST / Hyper-Threading T echnology * Refer to www .
xii ASUS Unique features ASUS Power Saving solution: - ASUS EPU-WS Engine - ASUS 8-Phase Power Design - ASUS AI Nap ASUS Workstation Features : - G.P .
xiii Back Panel I/O Ports 1 x PS/2 Keyboard / Mouse combo port 1 x S/PDIF Out (Coaxial + Optical) port 2 x External SA T A port 1 x IEEE1394a port 2 x RJ45 ports 6 x USB 2.
xiv.
1 Product introduction This chapter describes the motherboard features and the new technologies it supports..
ASUS P5Q WS Chapter summary 1 1.1 Welcome! ...................................................................................... 1-1 1.2 Package contents ......................................................................... 1-1 1.3 Special features .
ASUS P5Q WS 1-1 1.1 Welcome! Thank you for buying an ASUS ® P5Q WS motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of.
1-2 Chapter 1: Product Introduction 1.3 Special features 1.3.1 Product highlights Green ASUS This motherboard and its packaging comply with the European Union’s Restriction on the use of Hazardous Substances (RoHS).
ASUS P5Q WS 1-3 Dual RAID solution The Intel ® ICH10R chipset incorporates six Serial A T A connectors with high performance RAID 0, 1, 5, and 10 functions, and the Marvell ® controller provides ano.
1-4 Chapter 1: Product Introduction 1.3.2 ASUS unique features ASUS Express Gate T aking only 5 seconds to go online from bootup, Express Gate is the one-stop gateway to instant fun! It’s a unique motherboard built-in OS.
ASUS P5Q WS 1-5 ASUS Workstation Features ASUS Workstation features provide complete support to system maintenance and storage technology . G.P . Diagnosis card Bundled with P5Q WS motherboard (retail version), the G.
1-6 Chapter 1: Product Introduction ASUS Crystal Sound This feature can enhance speech-centric applications like Skype, online game, video conference and recording.
ASUS P5Q WS 1-7 ASUS CrashFree BIOS 3 ASUS CrashFree BIOS 3 allows users to restore corrupted BIOS data from a USB ash disk containing the BIOS le. See page 3-8 for details. ASUS MyLogo2™ This feature allows you to convert your favorite photo into a 256-color boot logo for a more colorful and vivid image on your screen.
1-8 Chapter 1: Product Introduction.
2 Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
2.1 Before you proceed ..................................................................... 2-1 2.2 Motherboard overview ................................................................. 2-2 2.3 Central Processing Unit (CPU) .........................
ASUS P5Q WS 2-1 2.1 Before you proceed T ake note of the following precautions before you install motherboard components or change any motherboard settings.
2-2 Chapter 2: Hardware information 2.2 Motherboard overview 2.2.1 Motherboard layout Refer to 2.7 Connectors for more information about rear panel connectors and internal connectors.
ASUS P5Q WS 2-3 2.2.2 Layout contents Connectors/Jumpers/Slots Page 1. A TX power connectors (24-pin EA TXPWR, 8-pin EA TX12V) 2-33 2. LGA775 CPU Socket 2-6 3. CPU, chassis, and power fan connectors (4-pin CPU_F AN; 3-pin CHA_F AN1/2; 3-pin PWR_F AN) 2-29 4.
2-4 Chapter 2: Hardware information 2.2.3 Placement direction When installing the motherboard, m ake sure that you place it into the ch assis in the correct orientation. The edge with external ports goes to the rear p art of the chassis as indicated in the image below .
ASUS P5Q WS 2-5 2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel ® Core™2 Extreme / Core™2 Quad / Core™2 Duo / Pentium ® dual-core / Celeron ® dual-core / Celeron ® Processors.
2-6 Chapter 2: Hardware information 2.3.1 Installing the CPU T o install a CPU: 1. Locate the CPU socket on the motherboard. Before installing the CPU, make sure that the cam box is facing towards you and the load lever is on your left. T o prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU.
ASUS P5Q WS 2-7 5. Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the socket then t the socket alignment key into the CPU notch.
2-8 Chapter 2: Hardware information The motherboard supports Intel ® LGA775 processors with the Intel ® Enhanced Memory 64 T echnology (EM64T), Enhanced Intel SpeedStep ® T echnology (EIST), and Hyper-Threading T echnology . Refer to the Appendix for more information on these CPU features.
ASUS P5Q WS 2-9 2.3.2 Installing the CPU heatsink and fan The Intel ® LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. • When you buy a boxed Intel ® processor , the package includes the CPU fan and heatsink assembly .
2-10 Chapter 2: Hardware information 3. Connect the CPU fan cable to the connector on the motherboard labeled CPU_F AN. DO NOT forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector . 2.3.3 Uninstalling the CPU heatsink and fan T o uninstall the CPU heatsink and fan: 1.
ASUS P5Q WS 2-1 1 2.4 System memory 2.4.1 Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM.
2-12 Chapter 2: Hardware information 2.4.2 Memory congurations Y ou may install 256 MB, 512 MB, 1 GB, and 2 GB non-ECC, unbuffered, DDR2 DIMMs into the DIMM sockets. • Y ou may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel conguration.
ASUS P5Q WS 2-13 P5Q WS Motherboard Qualied V endors Lists (QVL) DDR2-800MHz capability Size V endor Chip No. SS/ DS Part No. CL DIMM support A* B* C* 512MB A-DA TA AD29608A8A-25EG SS M2OAD6G3H3160.
2-14 Chapter 2: Hardware information SS - Single-sided / DS - Double-sided DIMM support: • A*: Supports one module inserted in any slot as Single-channel memory conguration. • B*: Supports one pair of modules inserted into either the yellow slots or the black slots as one pair of Dual-channel memory conguration.
ASUS P5Q WS 2-15 2.5.4 Removing a DIMM T o remove a DIMM 1. Simultaneously press the retaining clips outward to unlock the DIMM. 2. Remove the DIMM from the socket. Support the DIMM lightly with your ngers when pressing the retaining clips. The DIMM might get damaged when it ips out with extra force.
2-16 Chapter 2: Hardware information 2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. 2.5.1 Installing an expansion card T o install an expansion card: 1.
ASUS P5Q WS 2-17 2.5.3 Interrupt assignments IRQ assignments for this motherboard A B C D E F G H PCI1 shared – – – – – – – 1394 (FW322) – – – shared – – – – LAN 1 (81 1 1C.
2-18 Chapter 2: Hardware information PCI1 slot PCIe x16_1 slot (blue) PCIe x1_2 slot PCIX_1 slot PCIe 2.0 x16_2 slot (black) PCIe x1_1 slot 2.5.4 PCI slot The PCI slot supports cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specications.
ASUS P5Q WS 2-19 2.6 Jumpers 1. Clear RTC RAM (3-pin CLRTC) This jumper allows you to clear the Real T ime Clock (RTC) RAM in CMOS. Y ou can clear the CMOS memory of date, time, and s ystem setup parameters by erasing the CMOS RTC RAM data.
2-20 Chapter 2: Hardware information 2. CPU / Northbridge overvoltage setting (3-pin OV_CPU; 3-pin OV_NB) These jumpers allow you to enable or disable the advanced CPU and Northbridge overvoltage settings in BIOS. Read the following information before you change the jumper settings.
ASUS P5Q WS 2-21 3. PCI-X Speed setting (3-pin PCIX_SPEED) This jumper allows you to set the PCI-X slot’s maximum frequency capability . The jumper cap on pins 1-2: 133 MHz capability for the PCI-X slot. The jumper cap on pins 2-3: 100 MHz capability for the PCI-X slot.
2-22 Chapter 2: Hardware information 2.7 Connectors 2.7.1 Rear panel connectors 1. PS/2 keyboard / mouse combo port. This port is for a PS/2 keyboard or mouse. 2. Coaxial S/PDIF Out port. This port connects an external audio output device via a coaxial S/PDIF cable.
ASUS P5Q WS 2-23 9. Line Out port (lime). This port connects a headphone or a speaker . In 4-channel, 6-channel, and 8-channel conguration, the function of this port becomes Front Speaker Out. 10. Microphone port (pink). This port connects a microphone.
2-24 Chapter 2: Hardware information 2.7.2 Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided oppy disk drive (FDD) signal cable. Insert one end of the cable to this connector , then connect the other end to the signal connector at the back of the oppy disk drive.
ASUS P5Q WS 2-25 Drive jumper setting Mode of device(s) Cable connector Single device Cable-Select or Master - Black T wo devices Cable-Select Master Black Slave Gray Master Master Black or gray Slave Slave • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector .
2-26 Chapter 2: Hardware information Connect the right-angle side of SA T A signal cable to SA T A device. Or you may connect the right-angle side of SA T A cable to the onboard SA T A port to avoid mechanical conict with huge graphics cards. • These connectors are set to Standard IDE mode by default.
ASUS P5Q WS 2-27 4. USB connectors (10-1 pin USB78; USB910; USB1 1 12) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.
2-28 Chapter 2: Hardware information 5. IEE E 1394 a port connector (10-1 pin IE1394_2) This connector is for a IEEE 1394a port. Connect the IEEE 1394a module cable to this connector , then install the module to a slot opening at the back of the system chassis.
ASUS P5Q WS 2-29 6. CPU, chassis and power fan connectors (4-pin CPU_F AN, 3-pin CHA_F AN1/2, 3-pin PWR_F AN) The fan c onnect ors su pport co oling fans o f 350 mA–2000 mA (24 W max.) or a total of 1 A–7 A (84 W max.) at +12V . Connect the fan cables to the fan –7 A (84 W max.
2-30 Chapter 2: Hardware information 7. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch.
ASUS P5Q WS 2-31 9. Front panel audio co nne cto r (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector .
2-32 Chapter 2: Hardware information 1 1. TPM co nne cto r (20-1 pin TPM) [Optional] This connector supports a T rusted Platform Module (TPM) system, which can securely store keys, digital certicates, passwords, and data. A TPM system also helps enhance network security , protects digital identities, and ensures platform integrity .
ASUS P5Q WS 2-33 12. ATX po wer co nn ec tor s (24-pin EA TXPWR, 8-pin EA TX12V) These connectors are for A TX power supply plugs. The power supply plugs are designed to t these connectors in only one orientation. Find the proper orientation and push down rmly until the connectors completely t.
2-34 Chapter 2: Hardware information • System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector . The system power LED lights up when you turn on the system power , and blinks when the system is in sleep mode.
ASUS P5Q WS 2-35 ASUS Q-Connector (system panel) Y ou can use the ASUS Q-Connector to connect/disconnect chassis front panel cables in a few steps. Refer to the instructions below to install the ASUS Q- Connector . 1. Connect the front panel cables to the ASUS Q-Connector .
2-36 Chapter 2: Hardware information 2.8 G.P. Diagnosis card installation 2.8.1 G.P . Diagnosis card layout 1. Locate the TPM co nne cto r (20-1 pin TPM) on the motherboard (Refer to page 2-32 for the connector location).
ASUS P5Q WS 2-37 2.8.3 G.P . Diagnosis card check codes D0 Initiate chip 75 Detect IDE D1 Enable IO device for bootlock 78 Initiate option ROM D2 Check and wake up system 85 Show post error D3 Prepare.
2-38 Chapter 2: Hardware information 2.9 Starting up for the rst time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis.
ASUS P5Q WS 2-39 2.10 Turning off the computer 2.10.1 Using the OS shut down function If you are using Windows ® Vista: 1. Click the Start button and then select Shut Down . 2. The power supply should turn off after Windows ® shuts down. If you are using Windows ® XP: 1.
2-40 Chapter 2: Hardware information.
3 BIOS setup This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 3 ASUS P5Q WS 3.1 Managing and updating your BIOS ............................................ 3-1 3.2 BIOS setup program .................................................................... 3-9 3.3 Main menu ..........................
ASUS P5Q WS 3-1 3.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS Update (Updates the BIOS in Windows ® environment.) 2. ASUS EZ Flash 2 (Updates the BIOS using a oppy disk or USB ash disk.
3-2 Chapter 3: BIOS setup Quit all Windows ® applications before you update the BIOS using this utility . 3. Select the ASUS FTP site nearest you to avoid network trafc, or click Auto Select . Click Next . Updating the BIOS through the Internet T o update the BIOS through the Internet: 1.
ASUS P5Q WS 3-3 Updating the BIOS through a BIOS le T o update the BIOS through a BIOS le: 1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate . The ASUS Update main window appears.
3-4 Chapter 3: BIOS setup 3.1.2 Creating a bootable oppy disk 1. Do either one of the following to create a bootable oppy disk. DOS environment a. Insert a 1.44MB oppy disk into the drive. b. At the DOS prompt, type format A: / S then press <Enter>.
ASUS P5Q WS 3-5 3.1.3 ASUS EZ Flash 2 utility The ASUS EZ Flash 2 feature allows you to update the BIOS without having to go through the long process of booting from a oppy disk and using a DOS-based utility .
3-6 Chapter 3: BIOS setup 3.1.4 AFUDOS utility The AFUDOS utility allows you to update the BIOS le in DOS environment using a bootable oppy disk with the updated BIOS le. This utility also allows you to copy the current BIOS le that you can use as backup when the BIOS fails or gets corrupted during the updating process.
ASUS P5Q WS 3-7 2. Copy the AFUDOS utility (afudos.exe) from the motherboard support DVD to the bootable oppy disk you created earlier . 3. Boot the system in DOS mode, then at the prompt type: afudos /i[lename] where [lename] is the latest or the original BIOS le on the bootable oppy disk.
3-8 Chapter 3: BIOS setup 3.1.5 ASUS CrashFree BIOS 3 utility The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS le when it fails or gets corrupted during the updating process.
ASUS P5Q WS 3-9 3.2 BIOS setup program This motherboard supports a programmable rmware chip that you can update using the provided utility described in section 3.1 Managing and updating your BIOS . Use the BIOS Setup program when you are installing a motherboard, reconguring your system, or prompted to “Run Setup.
3-10 Chapter 3: BIOS setup 3.2.2 Menu bar The menu bar on top of the screen has the following main items: Main For changing the basic system conguration Ai T weaker For changing the overclocking se.
ASUS P5Q WS 3-1 1 3.2.4 Menu items The highlighted item on the menu bar displays the specic items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power , Boot, and Exit) on the menu bar have their respective menu items.
3-12 Chapter 3: BIOS setup 3.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. 3.3.1 System Time [xx:xx:xx] Allows you to set the system time. 3.3.2 System Date [Day xx/xx/xxxx] Allows you to set the system date.
ASUS P5Q WS 3-13 3.3.5 SA T A 1–6 While entering Setup, the BIOS automatically detects the presence of Serial A T A devices. There is a separate sub-menu for each SA T A device. Select a device item then press <Enter> to display the SA T A device information.
3-14 Chapter 3: BIOS setup DMA Mode [Auto] Selects the DMA mode. Conguration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting T echnology .
ASUS P5Q WS 3-15 Hard Disk Write Protect [Disabled] Disables or enables device write protection. This will be ef fective only if the device is accessed through BIOS. Conguration option: [Disabled] [Enabled] IDE Detect Time Out (Sec) [35] Selects the time out value for detecting A T A/A T API devices.
3-16 Chapter 3: BIOS setup 3.3.8 System Information This menu gives you an overview of the general system specications. The BIOS automatically detects the items in this menu. Bios Information Displays the auto-detected BIOS information. Processor Displays the auto-detected CPU specication.
ASUS P5Q WS 3-17 3.4 Ai Tweaker menu The Ai T weaker menu items allow you to congure overclocking-related items. T ake caution when changing the settings of the Ai T weaker menu items. Incorrect eld values can cause the system to malfunction. 3.
3-18 Chapter 3: BIOS setup Ratio CMOS Setting [Auto] Allows you to adjust the ratio between CPU Core Clock and FSB Frequency . Use the <+> and <-> keys to adjust the value. Conguration options: [Auto] [06.0] [07.0] [08.0] [09.0] [10.0] The following two items appear only when you set the Ai Overclock T uner item to [Manual].
ASUS P5Q WS 3-19 DRAM Timing Control [Auto] Conguration options: [Auto] [Manual] • The following sub-items apprear only when you set the DRAM Timing Control item to [Manual]. • The conguration options for some of the following items vary depending on the DIMMs you install on the motherboard.
3-20 Chapter 3: BIOS setup READ T o READ Delay(S) [Auto] Conguration options: [Auto] [1 DRAM Clocks]�[15 DRAM Clocks] READ T o READ Delay(D) [Auto] Conguration options: [Auto] [1 DRAM Clocks].
ASUS P5Q WS 3-21 Ai T ransaction Booster [Auto] Allows you to set the system performance. Conguration options: [Auto] [Manual] The following two sub-items appear only when you set the Ai T ransaction Booster item to [Manual].
3-22 Chapter 3: BIOS setup CPU PLL V oltage [Auto] Allows you to set the CPU PLL voltage. The values range from 1.50V to 2.78V with a 0.02V interval. FSB T ermination V oltage [Auto] Allows you to set the front side bus termination voltage. The values range from 1.
ASUS P5Q WS 3-23 NB GTL Reference [Auto] Allows you to set the Northbridge GTL voltage reference. Different ratio might enhance CPU overclocking ability . The values range from 0.370x to 0.760x with a 0.005x interval. SB V oltage [Auto] Allows you to set the South Bridge voltage.
3-24 Chapter 3: BIOS setup 3.5 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. T ake caution when changing the settings of the Advanced menu items. Incorrect eld values can cause the system to malfunction.
ASUS P5Q WS 3-25 Ratio CMOS Setting [Auto] Allows you to adjust the ratio between CPU Core Clock and FSB Frequency . Use the <+> and <-> keys to adjust the value. Conguration options: [Auto] [06.0] [07.0] [08.0] [09.0] [10.0] C1E Support [Enabled] Allows you to enable or disable Enhanced Halt State support.
3-26 Chapter 3: BIOS setup 3.5.2 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press <Enter> to display the sub-menu. North Bridge Conguration Memory Remap Feature [Enabled] Allows you to enable or disable the remapping of the overlapped PCI memory above the total physical memory .
ASUS P5Q WS 3-27 PCI Bus Frequency [Auto] Allows you to select the PCI bus speed. When this item is set to [Auto], PCI bus runs at the speed determined by the device installed.
3-28 Chapter 3: BIOS setup 3.5.3 Onboard Devices Conguration Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit v02.
ASUS P5Q WS 3-29 Marvell IDE/eSA T A [Legacy Mode] Allows you to disable the onboard Marvell IDE/eSA T A controller or set its mode. Conguration options: [Legacy Mode] [RAID Mode] [Disabled] If you want to create a RAID 0 or RAID 1 conguration from the Serial A T A hard disk drives, set this item to [RAID Mode].
3-30 Chapter 3: BIOS setup 3.5.4 USB Conguration The items in this menu allows you to change the USB-related features. Select an item then press <Enter> to display the conguration options. Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit v02.
ASUS P5Q WS 3-31 3.5.5 PCIPnP The PCIPnP menu items allow you to change the advanced settings for PCI/PnP devices. Plug And Play O/S [No] When set to [NO], BIOS congures all the devices in the system.
3-32 Chapter 3: BIOS setup 3.6 Power menu The Power menu items allow you to change the settings for the Advanced Power Management (APM). Select an item then press <Enter> to display the conguration options.
ASUS P5Q WS 3-33 3.6.5 APM Conguration Restore On AC Power Loss [Power Off] When set to [Power Off], the system goes into of f state after an AC power loss.
3-34 Chapter 3: BIOS setup 3.6.6 Hardware Monitor CPU T emperature [xxxºC/xxxºF] MB T emperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures. Select [Ignored] if you do not wish to display the detected temperatures.
ASUS P5Q WS 3-35 The following item appears only when you enable the CPU Q-Fan Control item. CPU Fan Profile [Standard] Allows you to set the appropriate performance level of the ASUS Q-Fan. When set to [Standard], the CPU fan automatically adjusts depending on the CPU temperature.
3-36 Chapter 3: BIOS setup 3.7 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu. 3.7.1 Boot Device Priority 1st ~ xxth Boot Device [xxx Drive] These items specify the boot device priority sequence from the available devices.
ASUS P5Q WS 3-37 3.7.2 Boot Settings Conguration Quick Boot [Enabled] Enabling this item allows the BIOS to skip some power on self tests (POST) while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items.
3-38 Chapter 3: BIOS setup 3.7.3 Security The Security menu items allow you to change the system security settings. Select an item then press <Enter> to display the conguration options. Change Supervisor Password Select this item to set or change the supervisor password.
ASUS P5Q WS 3-39 User Access Level [Full Access] This item allows you to select the access restriction to the Setup items. Conguration options: [No Access] [View Only] [Limited] [Full Access] [No Access] prevents user access to the Setup utility . [View Only] allows access but does not allow change to any eld.
3-40 Chapter 3: BIOS setup 3.8 Tools menu The T ools menu items allow you to congure options for special functions. Select an item then press <Enter> to display the sub-menu. Select Screen Select Item +- Change Field Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit v02.
ASUS P5Q WS 3-41 3.8.2 Express Gate Allows you to enable or disable the ASUS Express Gate feature. The ASUS Express Gate feature is a unique instant-on environment that provides quick access to the Internet browser and Skype. Refer to section 4.3.9 ASUS Express GA TE for details.
3-42 Chapter 3: BIOS setup 3.8.3 ASUS O.C. Prole This item allows you to store or load multiple BIOS settings. Save to Proe 1/2 Allows you to save the current BIOS le to the BIOS Flash. Press <Enter> to save the le. Load from Prole 1/2 Allows you to load the previous BIOS settings saved in the BIOS Flash.
ASUS P5Q WS 3-43 3.8.4 AI Net 2 Check Realtek LAN Cable [Disabled] Enables or disables checking of the Marvell LAN cable during the Power-On Self-T est (POST). Conguration options: [Disabled] [Enabled] v02.61 (C)Copyright 1985-2008, American Megatrends, Inc.
3-44 Chapter 3: BIOS setup Pressing <Esc> does not immediately exit this menu. Select one of the options from this menu or <F10> from the legend bar to exit. 3.9 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items.
4 Software support This chapter describes the contents of the support DVD that comes with the motherboard package and the software..
4.1 Installing an operating system ................................................... 4-1 4.2 Support DVD information ............................................................ 4-1 4.3 Software information ..........................................
ASUS P5Q WS 4-1 If Autorun is NOT enabled in your computer , browse the contents of the support DVD to locate the le ASSETUP .EXE from the BIN folder . Double-click the ASSETUP .EXE to run the DVD. Click an item to install 4.1 Installing an operating system This motherboard supports Windows ® XP/ 64-bit XP/ Vista™ operating systems (OS).
4-2 Chapter 4: Software support 4.2.2 Drivers menu The Drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. ASUS InstAll - Drivers Installation Wizard Installs all of the drivers through the Installation Wizard.
ASUS P5Q WS 4-3 4.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS InstAll - Installation Wizard for Utilities Installs all of the utilities through the Installation Wizard.
4-4 Chapter 4: Software support ASUS Update The ASUS Update utility allows you to update the motherboard BIOS in Windows ® environment. This utility requires an Internet connection either through a network or an Internet Service Provider (ISP). ASUS Express Gate Installer Installs the ASUS Express Gate application.
ASUS P5Q WS 4-5 4.2.4 Make disk menu The Make disk menu contains items to create the Intel ICH10R or Marvell ® 61xx driver disk. Intel ICH10R 32/64 bit RAID/AHCI Driver Disk Allows you to create an ICH10R 32/64bit RAID/AHCI driver disk. Marvell 61xx 32/64bit SA T A Driver Allows you to create a Marvell ® 61xx 32/64bit SA T A driver disk.
4-6 Chapter 4: Software support 4.2.5 Manual menu The Manual menu contains a list of supplementary user manuals. Click an item to open the folder of the user manual. Most user manual les are in Portable Document Format (PDF). Install the Adobe ® Acrobat ® Reader from the Utilities menu before opening a user manual le.
ASUS P5Q WS 4-7 Browse this DVD Displays the support DVD contents in graphical format. 4.2.7 Other information The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support DVD. Click an icon to display the specied information.
4-8 Chapter 4: Software support T echnical support Form Displays the ASUS T echnical Support Request Form that you have to ll out when requesting technical support.
ASUS P5Q WS 4-9 4.3 Software information Most of the applications in the support DVD have wizards that will conveniently guide you through the installation. View the online help or readme le that came with the software application for more information.
4-10 Chapter 4: Software support 9. When the screen returns to the ASUS Update utility , ash the original BIOS to load the new boot logo. 10. After ashing the BIOS, restart the computer to display the new boot logo during POST . 8. Adjust the boot image to your desired size by selecting a value on the Ratio box.
ASUS P5Q WS 4-1 1 4.3.2 ASUS PC Probe II PC Probe II is a utility that monitors the computer’s vital components, and detects and alerts you of any problem with these components. PC Probe II senses fan rotations, CPU temperature, and system voltages, among others.
4-12 Chapter 4: Software support Sensor alert When a system sensor detects a problem, the main window right handle turns red, as the illustrations below show . When displayed, the monitor panel for that sensor also turns red. Refer to the Monitor panels section for details.
ASUS P5Q WS 4-13 Changing the monitor panels position T o change the position of the monitor panels in the desktop, click the arrow down button of the Scheme options, then select another position from the list box. Click OK when nished. Moving the monitor panels All monitor panels move together using a magnetic effect.
4-14 Chapter 4: Software support Monitoring sensor alert The monitor panel turns red when a component value exceeds or is lower than the threshold value. Refer to the illustrations below . Large display Small display WMI browser Click to display the WMI (Windows Management Instrumentation) browser .
ASUS P5Q WS 4-15 PCI browser Click to display the PCI (Peripheral Component Interconnect) browser . This browser provides information on the PCI devices installed on your system. Click the plus sign (+) before the PCI Information item to display available information.
4-16 Chapter 4: Software support Memory usage The Memory tab shows both used and available physical memory . The pie chart at the bottom of the window represents the used (blue) and the available physical memory . Conguring PC Probe II Click to view and adjust the sensor threshold values.
ASUS P5Q WS 4-17 4.3.3 Audio congurations The Realtek ® ALC1200 audio CODEC provides 8-channel audio capability to deliver the ultimate audio experience on your computer . The software provides Jack-Sensing function, S/PDIF Out support, and interrupt capability .
4-18 Chapter 4: Software support Information Click the information button ( ) to display information about the audio driver version, DirectX version, audio controller , audio codec, and language setting. Minimize Click the minimize button ( ) to minimize the window .
ASUS P5Q WS 4-19 Audio I/O The Audio I/O option allows you congure your input/output settings. T o set the Audio I/O options: 1. From the Realtek HD Audio Manager , click the Audio I/O tab. 2. Click the drop-down menu to select the channel conguration.
4-20 Chapter 4: Software support Microphone The Microphone option allows you congure your input/output settings and to check if your audio devices are connected properly . T o set the Microphone options: 1. From the Realtek HD Audio Manager , click the Microphone tab.
ASUS P5Q WS 4-21 4.3.4 ASUS EPU-WS Engine ASUS EPU-WS Engine is an energy-efcient tool that satises different computing needs. This utility provides four modes that you can select to enhance system performance or save power . Selecting Auto mode will have the system shift modes automatically according to current system status.
4-22 Chapter 4: Software support WS Engine main menu Auto Mode Runs calibration T urbo Mode High Performance Mode Medium Power Saving Mode Max. Power Saving Mode Advanced settings for each mode (refer.
ASUS P5Q WS 4-23 Advanced settings menu Click Setting ( ) from the WS Engine main menu to display conguration options in each mode. Some options in certain modes are dimmed, meaning that they are not available.
4-24 Chapter 4: Software support Conguration options T urbo Mode High Performance Mode Medium Power Saving Mode Maximum Power Saving Mode CPU Frequency Overclocking +1% to +30% N/A Downclocking -1%.
ASUS P5Q WS 4-25 4.3.5 ASUS AI Suite ASUS AI Suite allows you to launch EPU-WS Engine, AI Booster , Fan Xpert, and Fan Xpert, and AI Nap utilities easily . Installing AI Suite T o install AI Suite on your computer: 1. Place the support DVD to the optical drive.
4-26 Chapter 4: Software support Other feature buttons Click on right corner of the main window to open the monitor window . Click on right corner of the expanded window to switch the temperature from degrees Centigrade to degrees Fahrenheit.
ASUS P5Q WS 4-27 4.3.6 ASUS AI Nap This feature allows you to minimize the power consumption of your computer whenever you are away . Enable this feature for minimum power consumption and a more quiet system operation.
4-28 Chapter 4: Software support 4.3.7 ASUS Fan Xpert Asus Fan Xpert intelligently allows you to adjust both the CPU and chassis fan speeds according to different ambient temperatures caused by dif ferent climate conditions in different geographic regions and your PC’s system loading.
ASUS P5Q WS 4-29 Click to get the calibration between the fan rotation and fan speed ratio Click to close the Calibration window Fan prole modes • Disable: Select this mode to disable the Fan Xpert function. • Standard: This mode makes the fan adjust speed in moderate pattern.
4-30 Chapter 4: Software support 4.3.8 ASUS AI Booster The ASUS AI Booster application allows you to overclock the CPU speed in WIndows ® environment without the hassle of booting the BIOS.
ASUS P5Q WS 4-31 4.3.9 ASUS Express Gate ASUS Express Gate is an instant-on environment that gives you quick access to the Internet. Within a few seconds of powering on your computer , you will be at the Express Gate menu where you can start the web browser , Skype, or other Express Gate softwares.
4-32 Chapter 4: Software support The First Screen Express Gate’s rst screen appears within a few seconds after you power on the computer . From here, you can immediately start the web browser or Skype. Y ou can also choose to continue booting normally (e.
ASUS P5Q WS 4-33 Knowing the Express Gate hot-keys Here is a list of common-used hot-keys for Express Gate. In the First Screen: Key Function P AUSE/BREAK Power-off ESC Continue to boot OS DEL Enter B.
4-34 Chapter 4: Software support Using the Conguration Panel Use the conguration panel to change various Express Gate settings. Click on an icon to open a particular conguration tool. The following tools are available: • Date and T ime : set current date and time as well as time zone.
ASUS P5Q WS 4-35 • Screen Settings : Choose the most optimal screen resolution for your display . • V olume Control : Control the volume for your speaker output, microphone input, etc. Using the LaunchBar The LaunchBar has several system icons that show you various system statuses and let you congure individual Express Gate settings.
4-36 Chapter 4: Software support Click to choose input language and method as well as keyboard shortcuts (Ctrl-Space by default). Click to change LaunchBar options (auto-hide, docking position, etc). Click to show the “ASUS Utility” panel. Click to show “About Express Gate ”.
ASUS P5Q WS 4-37 2. Open Network. 3. Make the proper network congurations. Each network interface is enabled immediately when you check the box next to it. Network • If you use a network cable connected to a home router (which is then connected to your DSL/cable modem), enable both LAN1 and LAN2.
4-38 Chapter 4: Software support • If you have wireless network, click Setup for the W iFi option. In the WiFi tab of the Advanced Network Settings box, enter the name of your wireless access point in the SSID eld. If your wireless access point has security enabled, select the corresponding security algorithm from the drop-down list (e.
ASUS P5Q WS 4-39 Conguring Express Gate in BIOS Setup Enter BIOS setup by pressing DEL key after powering on or by clicking on the BIOS setup icon on Express Gate’s rst screen. Express Gate conguration options are under the T ools menu. Refer to section 3.
4-40 Chapter 4: Software support 4.4 RAID congurations The motherboard comes with two RAID controllers that allow you to congure Serial A T A hard disk drives as RAID sets.
ASUS P5Q WS 4-41 4.4.3 Intel ® RAID congurations This motherboard supports RAID 0, RAID 1, RAID 5, RAID 10 and Intel ® Matrix Storage congurations for Serial A T A hard disks drives through the Intel ® ICH10R Southbridge chip. Setting the RAID item in BIOS Y ou must set the RAID item in the BIOS Setup before you can create a RAID set(s).
4-42 Chapter 4: Software support Intel ® Matrix Storage Manager option ROM utility The Intel ® Matrix Storage Manager Option ROM utility allows you to create RAID 0, RAID 1, RAID 10 (RAID 0+1), and RAID 5 set(s) from Serial A T A hard disk drives that are connected to the Serial A T A connectors supported by the Southbridge.
ASUS P5Q WS 4-43 Creating a RAID 0 set (striped) T o create a RAID 0 set: 1. From the utility main menu, select 1. Create RAID V olume and press <Enter>. The following screen appears. 2. Enter a name for the RAID 0 set and press <Enter>. 3.
4-44 Chapter 4: Software support 6. Use the up/down arrow key to select the stripe size for the RAID 0 array , and then press <Enter>. The available stripe size values range from 4 KB to 128 KB.
ASUS P5Q WS 4-45 Creating a RAID 1 set (mirrored) T o create a RAID 1 set: 1. From the utility main menu, select 1. Create RAID V olume and press <Enter>. The following screen appears. 2. Enter a name for the RAID 1 set and press <Enter>. 3.
4-46 Chapter 4: Software support Creating a RAID 10 set (RAID 0+1) T o create a RAID 10 set: 1. From the utility main menu, select 1. Create RAID V olume and press <Enter>. The following screen appears. 2. Enter a name for the RAID 10 set and press <Enter>.
ASUS P5Q WS 4-47 Creating a RAID 5 set (parity) T o create a RAID 5 set: 1. From the utility main menu, select 1. Create RAID V olume and press <Enter>. The following screen appears. WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 7.
4-48 Chapter 4: Software support 4. The Disks item is highlighted, press <Enter> to select the hard disk drives to congure as RAID. The following screen appears. 5. Use the up/down arrow key to highlight the drive you want to set, and then press <Space> to select.
ASUS P5Q WS 4-49 4.4.4 Marvell ® RAID congurations The Marvell ® 6121 Serial A T A controller allows you to congure RAID 0 and RAID 1 sets on the Serial A T A hard disk drives. Setting the RAID item in BIOS Y ou must set the RAID item in the BIOS Setup before you can create a RAID set(s).
4-50 Chapter 4: Software support Marvell ® RAID BIOS Conguration utility T o enter the Marvell ® RAID BIOS Conguration utility: 1. Boot up your computer . 2. During POST , press <Ctrl> + <M> to enter the utility main menu. Marvell BIOS Setup (c) 2006 Marvell Technology, Ltd.
ASUS P5Q WS 4-51 Creating a RAID 0 or RAID 1 set T o create a RAID set: 1. From the utility menu bar , highlight Create on the top. Marvell BIOS Setup (c) 2006 Marvell Technology, Ltd.
4-52 Chapter 4: Software support 4. The "Create Array" screen appears. Marvell BIOS Setup (c) 2006 Marvell Technology, Ltd. ENTER/SPACE:Select, ESC:Back/Exit Select free disks to create ID Port Disk Name Size Speed Status * 0 0 SATA: HDS721010KLA330 164.
ASUS P5Q WS 4-53 6. A conrmation screen appears. Press <Y> to conrm the array creation. 7. The newly created array appears in Arrays Information. Marvell BIOS Setup (c) 2006 Marvell Technology, Ltd. Select free disks to create ID Port Disk Name Size Speed Status * 0 0 SATA: HDS721010KLA330 164.
4-54 Chapter 4: Software support Deleting an array T o delete a RAID set: 1. From the utility menu bar , select Delete on the top and press <Enter>. The "Delete array" screen appears. 2. Select a desired array to delete and select NEXT .
ASUS P5Q WS 4-55 4.5.2 Creating a RAID driver disk in Windows ® T o create a RAID driver disk in Windows ® : 1. Start Windows ® . 2. Place the motherboard support DVD into the optical drive. 3. Go to the Make disk menu, and then click Intel ICH10R 32/64 bit RAID Driver Disk to create an Intel ® ICH10R RAID driver disk.
4-56 Chapter 4: Software support T o install the RAID driver in Windows XP: 1. During the OS installation, the system prompts you to press the <F6> key to install third-party SCSI or RAID driver . 2. Press <F6> then insert the oppy disk with RAID driver into the oppy disk drive.
A CPU features The Appendix describ es the CPU features and technologies that the motherboard supports..
ASUS P5Q WS Chapter summary A A.1 Intel ® EM64T .................................................................................. A-1 A.2 Enhanced Intel SpeedStep ® T echnology (EIST) ........................ A-1 A.3 Intel ® Hyper-Threading T echnology .
ASUS P5Q WS A-1 A.1 Intel ® EM64T • The motherboard is fully compatible with Intel ® LGA775 processors running on 32-bit operating systems. • The motherboard comes with a BIOS le that supports EM64T . Y ou can download the latest BIOS le from the ASUS website (www .
A-2 Appendix: CPU features A.2.2 Using the EIST T o use the EIST feature: 1. T urn on the computer , then enter the BIOS Setup. 2. Go to the Advanced Menu, highlight CPU Conguration, then press <Enter>. 3. Set the Intel(R) SpeedStep T echnology item to [Automatic], then press <Enter>.
ASUS P5Q WS A-3 A.3 Intel ® Hyper-Threading Technology • The motherboard supports Intel ® Pentium ® LGA775 processors with Hyper- Threading T echnology . • Hyper-Threading T echnology is supported under Windows ® Vista/XP and Linux 2.4.x (kernel) and later versions only .
A-4 Appendix: CPU features.
Een belangrijk punt na aankoop van elk apparaat Asus P5Q WS (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Asus P5Q WS heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Asus P5Q WS vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Asus P5Q WS leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Asus P5Q WS krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Asus P5Q WS bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Asus P5Q WS kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Asus P5Q WS . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
