Gebruiksaanwijzing /service van het product Striker Extreme van de fabrikant Asus
Ga naar pagina of 172
Motherboard Striker Extreme.
ii E3235 Second Edition V2 May 2007 Copyright © 2007 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transm.
iii Contents Notices ........................................................................................................ vii Safety information .................................................................................... viii About this guide .
iv Contents 2.5.5 PCI Express x1 slot ....................................................... 2-24 2.5.6 PCI Express x16 slots ................................................... 2-24 2.6 Jumper ........................................................
v Contents 4.3.2 System Date ................................................................. 4-13 4.3.3 Language ...................................................................... 4-13 4.3.4 Legacy Diskette A ....................................
vi Contents 4.8 T ools menu ................................................................................. 4-42 4.8.1 ASUS Music Alarm ........................................................ 4-42 4.8.2 ASUS O.C. Prole ..........................
vii Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
viii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
ix About this guide This user guide contains the information you need when installing and conguring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports.
x Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. T ypography Bold text Indicates a menu or an item to select. Italics Used to emphasize a word or a phrase.
xi Striker Extreme specications summary CPU LGA775 socket for Intel ® Core™2 Extreme / Core™2 Duo / Pentium ® Extreme / Pentium ® D / Pentium ® 4 / Celeron ® D Processors Intel ® Quad-core CPU Ready Compatible with Intel ® 06/05B/05A processors Note : Visit the ASUS website at www.
xii Striker Extreme specications summary High Denition Audio SupremeFX Audio Card - ADI 1988B 8-channel High Denition Audio CODEC - Supports Jack-Sensing, Enumeration, Multi-streaming and Jac.
xiii Striker Extreme specications summary Internal connectors 1 x Floppy disk drive connector 1 x IDE connector for 2 devices 6 x Serial A T A connectors 3 x USB 2.
xiv.
1 Product introduction This chapter describes the motherboard features and the new technologies it supports..
ASUS Striker Extreme Chapter summary 1 1.1 Welcome! ...................................................................................... 1-1 1.2 Package contents ......................................................................... 1-1 1.3 Special features .
ASUS Striker Extreme 1-1 1.1 Welcome! Thank you for buying an ASUS ® Striker Extreme motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout i.
1-2 Chapter 1: Product Introduction 1.3 Special features 1.3.1 Product highlights Republic of Gamers The Republic of Gamers consists only the best of the best. We of fer the best hardware engineering, the fastest performance, the most innovating ideas, and we welcome the best gamers to join in.
ASUS Striker Extreme 1-3 DDR2 memory support The motherboard supports DDR2 memory that features data transfer rates of 800/667/533 MHz to meet the higher bandwidth requirements of the latest 3D graphics, multimedia, and Internet applications.
1-4 Chapter 1: Product Introduction S/PDIF digital sound ready This motherboard provides convenient connectivity to external home theater audio systems via coaxial and optical S/PDIF-out (SONY/PHILIPS Digital Interface) jacks.It allows to transfer digital audio without converting to analog format and keeps the best signal quality .
ASUS Striker Extreme 1-5 1.3.2 ASUS unique features 8-phase cap-less Power design The 8-phase EL Capless Power Design demonstrates two hardcore commitments of ROG products: ultimate overclocking capability , and ultimate reliability .
1-6 Chapter 1: Product Introduction ASUS LCD Poster The LCD Poster displays actual boot error messages instead of codes that other debug cards show . This unique feature allows you to easily nd out which devices fail during the boot process, eliminating guesswork and allowing you to solve the problem immediately .
ASUS Striker Extreme 1-7 C.P .R. (CPU Parameter Recall) The C.P .R. feature of the motherboard BIOS allows automatic re-setting to the BIOS default settings in case the system hangs due to overclocking. When the system hangs due to overclocking, C.P .
1-8 Chapter 1: Product Introduction.
2 Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
ASUS Striker Extreme Chapter summary 2 2.1 Before you proceed ..................................................................... 2-1 2.2 Motherboard overview ................................................................. 2-2 2.3 Central Processing Unit (CPU) .
ASUS Striker Extreme 2-1 Onboard LED Blue lights strategically located beside key motherboard connectors allow you to install components conveniently , even without a ashlight. 2.1 Before you proceed T ake note of the following precautions before you install motherboard components or change any motherboard settings.
2-2 Chapter 2: Hardware information STR IKER EXTRE ME ® 2.2 Motherboard overview Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it. Make sure to unplug the power cord before installing or removing the motherboard.
ASUS Striker Extreme 2-3 2.2.3 ASUS Stack Cool 2 The motherboard comes with the ASUS Stack Cool 2 cooling solution that lowers the temperature of critical heat generating components. The motherboard uses a special design on the printed circuit board (PCB) to dissipate heat that critical components generate.
2-4 Chapter 2: Hardware information 2.2.4 Motherboard layout P ANEL ST RIK ER E XTR EME ® CHASSIS PRI_IDE 24.5cm (9.6in) CPU_FAN DDR2 DIMM_B1 (64 bit,240-pin module) DDR2 DIMM_A1 (64 bit,240-pin modu.
ASUS Striker Extreme 2-5 2.2.5 Layout contents Slots Page 1. DDR2 DIMM slots 2-15 2. PCI slots 2-24 3. PCI Express x1 slot 2-24 4. PCI Express x16 slots 2-24 Jumper Page 1. Clear RTC RAM (3-pin CLR TC_EN ) 2-25 Rear panel connectors Page 1. PS/2 mouse port (green) 2-27 2.
2-6 Chapter 2: Hardware information Internal connectors Page 1. Floppy disk drive connector (34-1 pin FLOPPY) 2-30 2. IDE connector (40-1 pin PRI_IDE ) 2-30 3. Serial A T A connectors (7-pin SA T A1, SA T A2, SA T A3, SA T A4, SA T A5, SA T A6) 2-31 4.
ASUS Striker Extreme 2-7 2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel ® Quad-core / Core™2 Extreme / Core™2 Duo / Pentium ® Extreme / Pentium ® D/ Pentium ® 4 and Celeron ® D processors.
2-8 Chapter 2: Hardware information 3. Lift the load lever in the direction of the arrow to a 135º angle. 2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab. Retention tab Load lever This side of the socket box should face you.
ASUS Striker Extreme 2-9 5. Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the socket then t the socket alignment key into the CPU notch. Alignment key Gold triangle mark 6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab.
2-10 Chapter 2: Hardware information Fastener Motherboard hole 2.3.2 Installing the CPU heatsink and fan The Intel ® LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. T o install the CPU heatsink and fan: 1.
ASUS Striker Extreme 2-1 1 3. Connect the CPU fan cable to the connector on the motherboard labeled CPU_F AN. 2. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place.
2-12 Chapter 2: Hardware information T o uninstall the CPU heatsink and fan: 1. Disconnect the CPU fan cable from the connector on the motherboard. 2. Rotate each fastener counterclockwise. 3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard.
ASUS Striker Extreme 2-13 5. Rotate each fastener clockwise to ensure correct orientation when reinstalling. Narrow end of the groove Refer to the documentation in the boxed or stand-alone CPU fan package for detailed information on CPU fan installation.
2-14 Chapter 2: Hardware information 2.3.4 Installing the optional fan 1. Position the fan above the pipe and heatsink assembly . 2. Fit the grooved edge to the heatsink. 3. Carefully push down the fan until it snugly ts the heatsink, then connect the fan cables.
ASUS Striker Extreme 2-15 2.4 System memory 2.4.1 Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM.
2-16 Chapter 2: Hardware information 2.4.2 Memory congurations Y ou may install 256 MB, 512 MB, 1 GB, and 2 GB unbuffered non-ECC DDR2 DIMMs into the DIMM sockets.
ASUS Striker Extreme 2-17 Striker Extreme Motherboard Qualied V endors Lists (QVL) DDR2-667MHz capability Size V endor Chip No. SS/ DS Part No. DIMM support A* B* C* 256MB KINGSTON HYB18T256800AF3 .
2-18 Chapter 2: Hardware information Striker Extreme Motherboard Qualied V endors Lists (QVL) DDR2-667MHz capability Size V endor Chip No. SS/ DS Part No.
ASUS Striker Extreme 2-19 Size V endor Chip No. SS/ DS Part No. DIMM support A* B* C* 512MB KINGSTON K4T51083QC SS KVR800D2N5/512 • • • 1024MB KINGSTON Heat-Sink Package DS KHX6400D2LL/1G • .
2-20 Chapter 2: Hardware information Striker Extreme Motherboard Qualied V endors Lists (QVL) DDR2-800MHz capability Size V endor Chip No. SS/ DS Part No.
ASUS Striker Extreme 2-21 2.4.3 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. T o install a DIMM: 1. Unlock a DIMM socket by pressing the retaining clips outward.
2-22 Chapter 2: Hardware information 2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. 2.5.1 Installing an expansion card T o install an expansion card: 1.
ASUS Striker Extreme 2-23 2.5.3 Interrupt assignments IRQ assignments for this motherboard A B C D E F G H PCIEx16_1 – – – – shared – – – PCIEx16_2 – – – – – shared – – PCI.
2-24 Chapter 2: Hardware information 2.5.4 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specications.
ASUS Striker Extreme 2-25 STRIKER EXTREME ® STRIKER EXTREME Clear RTC RAM CLRTC_EN Normal Clear RTC (Default) 1 2 2 3 2.6 Jumper Clear RTC RAM (CLRTC_EN) This jumper allows you to enable the CLRTC switch. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data.
2-26 Chapter 2: Hardware information 2.7 Audio Card and EL I/O Installation 2.7.1 Audio Card Installation 2.7.2 EL I/O Installation 1. T ake out the Audio card from the package. 2. Locate the slot on the motherboard. 3. Align the card connector with the slot and press rmly until the card sits on the slot completely .
ASUS Striker Extreme 2-27 1 17 2 3 4 5 12 13 14 15 6 7 8 9 10 1 1 16 2.8 Connectors 2.8.1 Rear panel connectors 1. PS/2 mouse port (green). This port is for a PS/2 mouse. 2. Coaxial S/PDIF Out port. This port connects an external audio output device via an optical S/PDIF cable.
2-28 Chapter 2: Hardware information 64-bit OS LAN port LED indications 6. Line In port (light blue). This port connects the tape, CD, DVD player , or other audio sources. 7. Line Out port (lime). This port connects a headphone or a speaker . In 4-channel, 6-channel, and 8-channel conguration, the function of this port becomes Front Speaker Out.
ASUS Striker Extreme 2-29 • DO NOT insert a dif ferent connector to this port. • DO NOT unplug the external Serial A T A box when a RAID 0 or RAID 1 is congured.
2-30 Chapter 2: Hardware information 2.8.2 Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided oppy disk drive (FDD) signal cable. Insert one end of the cable to this connector , then connect the other end to the signal connector at the back of the oppy disk drive.
ASUS Striker Extreme 2-31 3. Serial A T A connectors (7-pin SA T A1, SA T A2, SA T A3, SA T A4, SA T A5, SA T A6) These connectors are for the Serial A T A signal cables for Serial A T A hard disk drives.
2-32 Chapter 2: Hardware information Connect the right-angle side of SA T A signal cable to the SA T A device, or connect the right-angle side of the SA T A cable to the onboard SA T A port to avoid mechanical conict with huge graphics cards. Right-angle side 4.
ASUS Striker Extreme 2-33 5. IEE E 1394 a port connector (10-1 pin IE1394_2) This connector is for a IEEE 1394a port. Connect the IEEE 1394a module cable to this connector , then install the module to a slot opening at the back of the system chassis. Never connect a USB cable to the IEEE 1394a connector .
2-34 Chapter 2: Hardware information 6. CPU, chassis, power , and optional fan connectors (4-pin CPU_F AN, 3-pin CHA_F AN1, 3-pin PWR_F AN, 3-pin OPT_F AN1~5) The fan c onnect ors su pport co oling fans o f 350 mA ~ 2000 mA (24 W max.) or a total of 1 A ~ 7 A (84 W max.
ASUS Striker Extreme 2-35 8. AT X p owe r c on ne cto rs (24-pin EA TXPWR, 2 x 4-pin A TX12V) These connectors are for A TX power supply plugs. The power supply plugs are designed to t these connectors in only one orientation. Find the proper orientation and push down rmly until the connectors completely t.
2-36 Chapter 2: Hardware information • For a fully congured system, we recommend that you use a power supply unit (PSU) that complies with A TX 12 V Specication 2.0 (or later version) and provides a minimum power of 550 W . • Do not forget to connect the 4-pin/8pin EA TX12V power plug; otherwise, the system will not boot.
ASUS Striker Extreme 2-37 Normal Loading CPU PSC 3.73G 1066 DDR800 1GB*2 VGA Nvidia 7800GTX*2 SA T A-HD SA TA*4 ESA T A-HD 1 IDE-HD 1 CD-ROM 1 USB 2 PCI 1 +12V -V2 (4 PIN) +12V -V1 (24PIN) +5V +3.3V VGA +12V HDD +12V HDD +5V +5VSB T otal PSU Po_max (W) Io_max (A) 12.
2-38 Chapter 2: Hardware information 9. S/PDIF output co nne cto r (4-1 pin SPDIF_02) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). Connect the S/PDIF Out module cable to this connector , then install the module to a slot opening at the back of the system chassis.
ASUS Striker Extreme 2-39 • System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector . The system power LED lights up when you turn on the system power , and blinks when the system is in sleep mode.
2-40 Chapter 2: Hardware information ASUS Q-Connector (system panel) Y ou can use the ASUS Q-Connector to connect/disconnect chassis front panel cables in a few steps. Refer to the instructions below to install the ASUS Q- Connector . 1. Connect the front panel cables to the ASUS Q-Connector .
ASUS Striker Extreme 2-41 2.8.3 Onboard switches Onboard switches allow you to ne-tune performance when working on a bare or open-case system. This is ideal for overclockers and gamers who continually change settings to enhance system performance. 1.
2-42 Chapter 2: Hardware information 2. Power-on switch Press the clear power-on switch to wake/power up the system. 3. Reset switch Press the reset switch to reboot the system.
3 Powering up This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system..
ASUS Striker Extreme Chapter summary 3 3.1 Starting up for the rst time ........................................................ 3-1 3.2 T urning off the computer .
ASUS Striker Extreme 3-1 3.1 Starting up for the rst time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis.
3-2 Chapter 3: Powering up 3.2 Turning off the computer 3.2.1 Using the OS shut down function If you are using Windows ® 2000: 1. Click the Start button then click Shut Down... 2. Make sure that the Shut Down option button is selected, then click the OK button to shut down the computer .
4 BIOS setup This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4 ASUS Striker Extreme 4.1 Managing and updating your BIOS ............................................ 4-1 4.2 BIOS setup program .................................................................... 4-9 4.3 Main menu .................
ASUS Striker Extreme 4-1 4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS Update (Updates the BIOS in Windows ® environment.) 2. ASUS EZ Flash 2 (Updates the BIOS in DOS using a oppy disk or a USB ash disk.
4-2 Chapter 4: BIOS setup Quit all Windows ® applications before you update the BIOS using this utility . 3. Select the ASUS FTP site nearest you to avoid network trafc, or click Auto Select . Click Next . Updating the BIOS through the Internet T o update the BIOS through the Internet: 1.
ASUS Striker Extreme 4-3 Updating the BIOS through a BIOS le T o update the BIOS through a BIOS le: 1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate . The ASUS Update main window appears.
4-4 Chapter 4: BIOS setup 4.1.2 Creating a bootable oppy disk 1. Do either one of the following to create a bootable oppy disk. DOS environment a. Insert a 1.44MB oppy disk into the drive. b. At the DOS prompt, type format A: / S then press <Enter>.
ASUS Striker Extreme 4-5 T o update the BIOS using EZ Flash 2: 1. Visit the ASUS website (www .asus.com) to download the latest BIOS le for the motherboard. 2. Save the BIOS le to a oppy disk, then restart the system. 3. Y ou can launch the EZ Flash 2 by two methods.
4-6 Chapter 4: BIOS setup 4.1.4 Updating the BIOS The Basic Input/Output System (BIOS) can be updated using the AwardBIOS Flash Utility . Follow these instructions to update the BIOS using this utility . 1. Download the latest BIOS le from the ASUS web site.
ASUS Striker Extreme 4-7 7. Press <N> when the utility prompts you to save the current BIOS le. The following screen appears. 8. The utility veries the BIOS le in the oppy disk and starts ashing the BIOS le. Do not turn off or reset the system during the ashing process! AwardBIOS Flash Utility for ASUS V1.
4-8 Chapter 4: BIOS setup 4. The utility saves the current BIOS le to the oppy disk, then returns to the BIOS ashing process. 3. T ype a lename for the current BIOS le in the Save current BIOS as eld, then press <Enter>. T o save the current BIOS le using the AwardBIOS Flash Utility: 1.
ASUS Striker Extreme 4-9 4.2 BIOS setup program This motherboard supports a programmable Low-Pin Count (LPC) chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconguring your system, or prompted to“Run Setup.
4-10 Chapter 4: BIOS setup 4.2.1 BIOS menu screen Select Menu Item Specic Help Change the day, month, year and century. Legend bar General help Menu bar Sub-menu items Conguration elds Menu i.
ASUS Striker Extreme 4-1 1 4.2.4 Menu items The highlighted item on the menu bar displays the specic items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power , Boot, and Exit) on the menu bar have their respective menu items.
4-12 Chapter 4: BIOS setup 4.2.7 Pop-up window Select a menu item then press <Enter> to display a pop-up window with the conguration options for that item.
ASUS Striker Extreme 4-13 F1:Help ↑↓ : Select Item -/+: Change Value F5: Setup Defaults ESC: Exit →← : Select Menu Enter: Select SubMenu F10: Save and Exit Phoenix-Award BIOS CMOS Setup Utility Main Extreme Tweaker Advanced Power Boot Tools Exit Select Menu Item Specic Help Change the day, month, year and century.
4-14 Chapter 4: BIOS setup 4.3.5 Primary IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press <Enter> to display the IDE device information.
ASUS Striker Extreme 4-15 Capacity Displays the auto-detected hard disk capacity . This item is not congurable. Cylinder Shows the number of the hard disk cylinders. This item is not congurable. Head Shows the number of the hard disk read/write heads.
4-16 Chapter 4: BIOS setup 4.3.6 S A T A 1 / 2 / 3 / 4 / 5 / 6 While entering Setup, the BIOS automatically detects the presence of Serial A T A devices. There is a separate sub-menu for each SA T A device. Select a device item then press <Enter> to display the SA T A device information.
ASUS Striker Extreme 4-17 Head Shows the number of the hard disk read/write heads. This item is not congurable. Landing Zone Shows the number of landing zone per track. This item is not congurable. Sector Shows the number of sectors per track. This item is not congurable.
4-18 Chapter 4: BIOS setup 4.4 Extreme Tweaker menu The Extreme menu items allow you to congure overclocking-related items. Phoenix-Award BIOS CMOS Setup Utility Main Extreme Tweaker Advanced Power Boot Tools Exit Select Menu Item Specic Help Press [Enter] to select overclock prole .
ASUS Striker Extreme 4-19 The following items become user-congurable when you set AI T uning to [ Manual ]. System Clocks This sub-menu allows you to adjust the system frequency-related items.
4-20 Chapter 4: BIOS setup FSB - Memory Ratio [Auto] Conguration options: [Auto] [1:1] [5:4] [3:2] [Sync Mode] FSB (QDR), MHz [800] Conguration options: [533 MHz]~[2600 MHz] The following item becomes user-congurable when you set the FSB-Memory Clock Mode item to [Unlinked].
ASUS Striker Extreme 4-21 4.4.2 Overclocking This sub-menu allows you to adjust the system frequency-related items. Select an item, then press <Enter> to edit.
4-22 Chapter 4: BIOS setup MCP PCIE Spread Spectrum [Down Spread] Conguration options: [Disabled] [Down Spread] SA T A Spread Spectrum [Disabled] Conguration options: [Disabled] [Enabled] LDT Sp.
ASUS Striker Extreme 4-23 Intel SpeedStep [Disabled] This item is user-congurable only when you set [AI T uning] to [Standard], [Auto], or [AI N.O.S.
4-24 Chapter 4: BIOS setup DDR2 Channel A Ref V oltage / DDR2 Channel B Ref V oltage [Auto] Allows you to set the DDR2 Controller/ChannelA/B Ref voltage. Conguration options: Conguration options: [Auto] [DDR2_V ol/2] [DDR2_ V ol/2-30mv] [DDR2_V ol/2-20mv] [DDR2_V ol/2-10mv] [DDR2_V ol/2+10mv] [DDR2_V ol/2+20mv] [DDR2_V ol/2+30mv] 4.
ASUS Striker Extreme 4-25 POST Check LAN Cable [Disabled] POST Check LAN2 Cable [Disabled] Enables or disables checking of the LAN/LAN2 cable during the Power-On Self-T est (POST).
4-26 Chapter 4: BIOS setup Select Menu Item Specic Help Select Yes if you are using a Plug and Play capable operating system. Select No if you need the BIOS to congure non-boot devices. PCIPnP Plug & Play O/S [No] Primary Display Adapter [PCI] Phoenix-Award BIOS CMOS Setup Utility Advanced 4.
ASUS Striker Extreme 4-27 F1:Help ↑↓ : Select Item -/+: Change Value F5: Setup Defaults ESC: Exit →← : Select Menu Enter: Select SubMenu F10: Save and Exit Select Menu Item Specic Help Onbo.
4-28 Chapter 4: BIOS setup Serial-A T A Conguration This sub-menu allows you to change Serial A T A settings. Select an item then press <Enter> to edit.
ASUS Striker Extreme 4-29 Onboard 1394 [Enabled] Allows you to disable or enable the onboard 1394 device support. Conguration options: [Disabled] [Enabled] LCD Poster Backlight [Disabled] Allows you to enable or disable the LCD poster backlight.
4-30 Chapter 4: BIOS setup 4.6 Power menu The Power menu items allow you to change the settings for the Advanced Conguration and Power Interface (ACPI) and the Advanced Power Management (APM). Select an item then press <Enter> to display the conguration options.
ASUS Striker Extreme 4-31 4.6.3 APM Conguration Restore on AC Power Loss [Power-Off] Allows you to enable or disable the Restore on AC Power Loss function. Conguration options: [Power-Off] [Power-On] [Last State] PWR Button < 4 secs [Instant-Off] Allows you to set the event after the power button is pressed for more than 4 seconds.
4-32 Chapter 4: BIOS setup Alarm Time (hh:mm) [ X: X: X] T o set the time of alarm: 1. Highlight this item and press <Enter> to display a pop-up menu for the hour eld. 2. Key-in a value (Min=0, Max=23), then press <Enter>. 3. Press <T AB> to move to the minutes eld then press <Enter>.
ASUS Striker Extreme 4-33 V oltage Monitor Vcore / 3.3V / 5V / 12V V oltage +1.2V HT / +1.5V V oltage VTT CPU / DDR2 T ermination /DDR2 V oltage +1.4V / DDR2 V oltage The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators.
4-34 Chapter 4: BIOS setup Select Menu Item Specic Help Fan Speed Monitor CPU Fan Speed 2960 RPM CHA_FAN1 Speed 0 RPM OPT1 FAN Speed 0 RPM OPT2 FAN Speed 0 RPM OPT3 FAN Speed 0 RPM OPT4 FAN Speed 0.
ASUS Striker Extreme 4-35 CHA Fan Q-Fan Sense [CPU T emperature] Allows the Q-Fan to sense CPU/MB temperature and to adjust the fan speed. When the previous items are set to Q-F AN Mode, these items become user- congurable.
4-36 Chapter 4: BIOS setup CPU Fan Speed warning [600 RPM] Allows you to set the CPU fan warning speed function, which gives off a warning when the CPU fan speed is too low . If you set this item to [Disabled], the system will not warn you even if no fan is installed or if the fan is not functioning properly .
ASUS Striker Extreme 4-37 4.7 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu.
4-38 Chapter 4: BIOS setup 4.7.2 Removable Drives 1. Floppy Disks Allows you to assign a removable drive attached to the system. Select Menu Item Specic Help Removable Drives 1. Floppy Disks Phoenix-Award BIOS CMOS Setup Utility Boot 4.7.3 Hard Disk Drives 1.
ASUS Striker Extreme 4-39 4.7.5 Boot Settings Conguration F1:Help ↑↓ : Select Item -/+: Change Value F5: Setup Defaults ESC: Exit →← : Select Menu Enter: Select Sub-menu F10: Save and Exit Select Menu Item Specic Help Press [Enter] to enable or disable.
4-40 Chapter 4: BIOS setup T ypematic Rate (Chars/Sec) [6] Allows you to select the rate at which a character repeats when you hold a key . Conguration options: [6] [8] [10] [12] [15] [20] [24] [30] T ypematic Delay (Msec) [250] Allows you to set the delay before keystrokes begin to repeat.
ASUS Striker Extreme 4-41 3. When prompted, conrm the password by typing the exact characters again, then press <Enter>. The password eld setting is changed to Set. T o clear the password: 1. Select the password eld and press <Enter> twice.
4-42 Chapter 4: BIOS setup The succeeding items become user-congurable when you enable the ASUS Music Alarm. 4.8 Tools menu The T ools menu items allow you to congure options for special functions. Select an item then press <Enter> to display the sub-menu.
ASUS Striker Extreme 4-43 4.8.2 ASUS O.C. Prole This item allows you to store or load multiple BIOS settings. Select Menu Item Specic Help Press [Enter] to select. ASUS BIOS Prole Load BIOS Prole Save BIOS Prole Phoenix-Award BIOS CMOS Setup Utility Tools Select Menu Item Specic Help Load BIOS Prole from Prole 1.
4-44 Chapter 4: BIOS setup Load from Prole 1/2 Allows you to load the previous BIOS settings saved in the BIOS Flash. Press <Enter> to load the le. Load from File Allows you to load the previous BIOS le saved in the hard disk/oppy disk/USB ash disk with the F A T32/16/12 format.
ASUS Striker Extreme 4-45 4.8.3 ASUS EZ Flash 2 Allows you to run ASUS EZ Flash 2. When you press <Enter>, a conrmation message appears. Use the left/right arrow key to select between [Y es] or [No], then press <Enter> to conrm your choice.
4-46 Chapter 4: BIOS setup 4.9 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items.
5 Software support This chapter describes the contents of the support CD that comes with the motherboard package..
ASUS Striker Extreme Chapter summary 5 5.1 Installing an operating system ................................................... 5-1 5.2 Support DVD information ............................................................ 5-1 5.3 Software information ...
ASUS Striker Extreme 5-1 If Autorun is NOT enabled in your computer , browse the contents of the support DVD to locate the le ASSETUP .EXE from the BIN folder . Double-click the ASSETUP .EXE to run the DVD. 5.1 Installing an operating system This motherboard supports Windows ® 2000/2003 Server/XP/64-bit XP operating systems (OS).
5-2 Chapter 5: Software support 5.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. ASUS InstAll - Installation Wizard for Drivers Launches the ASUS InstAll driver installation wizard.
ASUS Striker Extreme 5-3 5.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS InstAll - Installation Wizard for Utilities Launches the ASUS InstAll utilities installation wizard.
5-4 Chapter 5: Software support Adobe Reader V7.0 Installs the Adobe ® Acrobat ® Reader that allows you to open, view , and print documents in Portable Document Format (PDF). Microsoft DirectX 9.0c Installs the Microsoft ® DirectX 9.0c driver . The Microsoft DirectX ® 9.
ASUS Striker Extreme 5-5 5.2.4 Make Disk menu The Make Disk menu contains items to create the NVIDIA ® nForce™ 680i SLI or Silicon Image SA T A RAID driver disk. Make nVidia 32bit SA T A RAID Driver Make nVidia 64bit SA T A RAID Driver Allows you to create an NVIDIA ® Serial A T A RAID driver disk for a 32-bit/64-bit system.
5-6 Chapter 5: Software support 5.2.6 ASUS Contact information Click the Contact tab to display the ASUS contact information. Y ou can also nd this information on the inside front cover of this user guide. 5.2.5 Manuals menu The Manuals menu contains a list of supplementary user manuals.
ASUS Striker Extreme 5-7 5.2.7 Other information The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support DVD. Click an icon to display the specied information. Motherboard Info Displays the general specications of the motherboard.
5-8 Chapter 5: Software support Filelist Displays the contents of the support DVD and a brief description of each in text format. T echnical support form Displays the ASUS T echnical Support Request Form that you have to ll out when requesting technical support.
ASUS Striker Extreme 5-9 5.3 Software information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme le that came with the software application for more information.
5-10 Chapter 5: Software support 9. When the screen returns to the ASUS Update utility , ash the original BIOS to load the new boot logo. 10. After ashing the BIOS, restart the computer to display the new boot logo during POST . 8. Adjust the boot image to your desired size by selecting a value on the Ratio box.
ASUS Striker Extreme 5-1 1 5.3.2 SoundMAX ® High Denition Audio utility The ADI AD1988B High Denition Audio CODEC provides 8-channel audio capability through the SoundMAX ® audio utility with AudioESP™ software to deliver the ultimate audio experience on your PC.
5-12 Chapter 5: Software support From the taskbar , double-click on the SoundMAX ® icon to display the SoundMAX ® Control Panel. Audio Setup Wizard By clicking the icon from the SoundMAX ® control panel, you can easily congure your audio settings.
ASUS Striker Extreme 5-13 Jack conguration This screen helps you congure your computer’s audio ports, depending on the audio devices you have installed. Adjust speaker volume This screen helps you adjust speaker volume. Click the T est button to hear the changes you have made.
5-14 Chapter 5: Software support Audio preferences Click the icon to go to the Preferences page. This page allows you to change various audio settings. General options Click the General tab to choose your playback and recording devices, enable/ disable the AudioESP™ feature, and enable/disable digital output.
ASUS Striker Extreme 5-15 Microphone options Click the Listening Environment tab allows you to optimize your microphone input settings. Enhanced Microphone Features Noise Filtering Enables Noise Filter function.
5-16 Chapter 5: Software support 5.3.3 ASUS PC Probe II PC Probe II is a utility that monitors the computer’s vital components, and detects and alerts you of any problem with these components. PC Probe II senses fan rotations, CPU temperature, and system voltages, among others.
ASUS Striker Extreme 5-17 Button Function Opens the Conguration window Opens the Report window Opens the Desktop Management Interface window Opens the Peripheral Component Interconnect window Opens.
5-18 Chapter 5: Software support Changing the monitor panels position T o change the position of the monitor panels in the desktop, click the arrow down button of the Scheme options, then select another position from the list box. Click OK when nished.
ASUS Striker Extreme 5-19 Monitoring sensor alert The monitor panel turns red when a component value exceeds or is lower than the threshold value. Refer to the illustrations below . Large display Small display WMI browser Click to display the WMI (Windows Management Instrumentation) browser .
5-20 Chapter 5: Software support PCI browser Click to display the PCI (Peripheral Component Interconnect) browser . This browser provides information on the PCI devices installed on your system. Click the plus sign (+) before the PCI Information item to display available information.
ASUS Striker Extreme 5-21 Memory usage The Memory tab shows both used and available physical memory . The pie chart at the bottom of the window represents the used (blue) and the available physical memory . Conguring PC Probe II Click to view and adjust the sensor threshold values.
5-22 Chapter 5: Software support 5.3.4 ASUS Music Alarm This motherboard is equipped with an audio alarm clock called ASUS Music Alarm. The ASUS Music Alarm gives you a personal wake-up called with your favorite CD music when the system is off.
ASUS Striker Extreme 5-23 OS conguration T o congure ASUS Music Alarm in Windows ® 1. Place the support CD into the optical drive. 2. Click the Utilities tab and choose ASUS Music Alarm to install the utility . 3. Insert an audio CD into the optical drive.
5-24 Chapter 5: Software support 7. Click the arrow ( ) next to Options in the Options section. The Options panel appears. Disable or select the Repeat mode, then specify the length of the alarm music to play . Set the desired volume. When done, click OK .
ASUS Striker Extreme 5-25 5.3.5 ASUS Ai Booster The ASUS Ai Booster application allows you to overclock the CPU speed in WIndows ® environment without the hassle of booting the BIOS. After installing the program from the bundled support CD, you can launch the utility by double-clicking the Ai Booster icon on the Windows ® OS taskbar .
5-26 Chapter 5: Software support 5.4 RAID congurations The motherboard comes with two RAID controllers that allow you to congure Serial A T A hard disk drives as RAID sets. • The Silicon Image ® Sil3132 RAID controller allows you to congure RAID 1 and RAID 0 sets on the external Serial A T A hard disk drives.
ASUS Striker Extreme 5-27 If you want to boot the system from a hard disk drive included in a RAID set, rst copy the RAID driver from the support DVD to a oppy disk before you install an operating system to a selected hard disk drive. Refer to section “5.
5-28 Chapter 5: Software support • For detailed descriptions on the NVIDIA ® RAID conguration, refer to the “NVIDIA ® RAID User Guide” found in your motherboard support CD. • When using Windows ® 2000 operating system, make sure to install the Windows ® 2000 Service Pack 4 or later version.
ASUS Striker Extreme 5-29 Creating a RAID V olume T o create a RAID volume: 1. From the NVIDIA ® RAID utility Dene a New Array menu, select RAID Mode then press <Enter>. The following submenu appears. Use the up or down arrow keys to select a RAID mode then press <Enter>.
5-30 Chapter 5: Software support Rebuilding a RAID array T o rebuild a RAID array: 1. From the Array List menu, use the up or down arrow keys to select a RAID array then press <Enter>.
ASUS Striker Extreme 5-31 A new set of navigation keys is displayed on the bottom of the screen. 2. Press <R> to rebuild a RAID array . The following screen appears. 3. Use the up or down arrow keys to select a RAID array to rebuild, then press <F7>.
5-32 Chapter 5: Software support Deleting a RAID array T o delete a RAID array: 1. From the Array List menu, use the up or down arrow keys to select a RAID array then press <Enter>. The RAID Array details appear . [R] Rebuild [D] Delete [C] Clear Disk [ENTER] Return Array 1 : NVIDIA MIRROR XXX.
ASUS Striker Extreme 5-33 Clearing a disk data T o clear disk data: 1. From the Array List menu, use the up or down arrow keys to select a RAID array then press <Enter>. The RAID Array details appear . [R] Rebuild [D] Delete [C] Clear Disk [ENTER] Return Array 1 : NVIDIA MIRROR XXX.
5-34 Chapter 5: Software support 5.4.3 Silicon Image ® RAID congurations The Silicon Image ® RAID controller allows you to congure RAID 1 and RAID 0 sets on the external Serial A T A hard disk drives. Use the Silicon Image RAID utility to congure a disk array .
ASUS Striker Extreme 5-35 Entering the Silicon Image BIOS RAID Conguration Utility T o enter the Silicon Image BIOS RAID conguration utility: 1. Boot up your computer .
5-36 Chapter 5: Software support Manual conguration a. Select Manual conguration and press <Enter>. The following pop-up menu appears. b. Use the up or down arrow keys to select a chunk size appropriate to your drive usage then press <Enter>.
ASUS Striker Extreme 5-37 2. Select RAID 1 then press <Enter> to display the following. MAIN MENU Auto conguration Manual conguration c. The selection bar moves to the Physical Drive menu Using the up or down arrowkeys, select a drive then press <Enter> to set the rst drive of the RAID set.
5-38 Chapter 5: Software support PHYSICAL DRIVE 0 XXXXXXXXXXX XXXXXXMB 1 XXXXXXXXXXX XXXXXXMB 2 XXXXXXXXXXX XXXXXXMB 3 XXXXXXXXXXX XXXXXXMB c. Repeat step b to select the target drive. d. After selecting the source and target drives, the following pop-up menu appears.
ASUS Striker Extreme 5-39 e. If you selected Create with data copy , the following pop-up menu appears. MAIN MENU Auto conguration Manual conguration online copy ofine copy The online copy option automatically copies the data to the target drives on the background while writing to the source drives.
5-40 Chapter 5: Software support • Congure a CONCA TENA TION set when using a single Serial A T A drive; otherwise, the system will not recognize the drive. • Y ou can also create a RAID set using the SA T ARAID5 GUI utility under a Windows ® environment.
ASUS Striker Extreme 5-41 5.5 Creating a RAID driver disk A oppy disk with the RAID driver is required when installing Windows ® 2000/XP operating system on a hard disk drive that is included in a RAID set. T o create a RAID driver disk: 1. Place the motherboard support DVD into the DVD-ROM drive.
5-42 Chapter 5: Software support.
6 This chapter tells how to install SLI-ready PCI Express graphics cards. NVIDIA ® SLI™ technology support.
ASUS Striker Extreme Chapter summary 6.1 Overview ....................................................................................... 6-1 6.2 Dual graphics cards setup .
ASUS Striker Extreme 6-1 6.1 Overview The motherboard supports the NVIDIA ® SLI™ (Scalable Link Interface) technology that allows you to install two identical PCI Express™ x16 graphics cards.
6-2 Chapter 6: NVIDIA ® SLI™ technology support 6.2 Dual graphics card setup 6.2.1 Installing SLI-ready graphics cards Install only identical SLI-ready graphics cards that are NVIDIA ® -certied. Different types of graphics cards will not work together properly .
ASUS Striker Extreme 6-3 4. Insert the second graphics card into the other slot (PCIEX16_3). Make sure that the card is properly seated on the slot. If required, connect an auxiliary power source to the PCI Express graphics cards. 3. Insert one graphics card into one of the blue slots (PCIEX16_1).
6-4 Chapter 6: NVIDIA ® SLI™ technology support 7. Connect a VGA cable or a DVI-I cable to the graphics card/s. We recommend to install an additional chassis fan for better thermal environment. 5. Align and insert the SLI connector to the goldngers on each graphics card.
ASUS Striker Extreme 6-5 NVIDIA Settings icon T o enable the multi-GPU feature: 1. Click the NVIDIA Settings icon on your Windows taskbar . 2. From the pop-up menu, select nView Desktop Manager then click nView Properties. Make sure that your PCI Express graphics card driver supports the NVIDIA SLI technology .
6-6 Chapter 6: NVIDIA ® SLI™ technology support 5. From the Display Properties dialog box, select the Settings tab then click Advanced. 6. Select the NVIDIA GeForce tab. 7. Click the slider to display the following screen, then select the SLI multi-GPU item.
Een belangrijk punt na aankoop van elk apparaat Asus Striker Extreme (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Asus Striker Extreme heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Asus Striker Extreme vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Asus Striker Extreme leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Asus Striker Extreme krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Asus Striker Extreme bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Asus Striker Extreme kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Asus Striker Extreme . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.