Gebruiksaanwijzing /service van het product 5620-A2-GN11-30 van de fabrikant Paradyne
Ga naar pagina of 24
1 Hotwire 5620 RTU Customer Premises Installation Instructions Document Number 5620-A2-GN1 1-30 August 2000 Contents What Does the Hotwire 5620 RTU Do? 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the DSL Access Wiring 6 .
2 NOTES: In this document: — End-user system is used to represent any host with an Ethernet connection. — Service provider is used to represent any Internet Service Provider (ISP) or remote LAN access provider .
3 DSL Access with a Hotwire 5030 or 5038 POTS Splitter When a Hotwire POTS splitter is used at both ends of the local loop, wiring is connected: From the demarcation point to the CP POTS splitter , and From the demarcation point to the DSL jack.
4 DSL Access with a Hotwire 5038 Distributed POTS Splitter When a Hotwire 5038 Distributed POTS Splitter is used, one 5038 Distributed POTS Splitter is installed as a phone filter for each telephone on the same POTS line as DSL.
5 Package Checklist V erify that your package contains the following: Model 5620 Remote T ermination Unit (RTU) DSL interface cable with RJ1 1 modular plugs Power cord with power transform.
6 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connected from the customer premises side of the punchdown block or the NID to an RJ1 1 jack. T ypically , the punchdown block is installed in commercial locations and the NID is installed in residential locations.
7 3. Locate the DSL pair of T1/R1 connectors on the customer premises side of the NID or punchdown block. Attach the wiring that will be connected to the DSL jack. In the following example, a NID is used without a POTS splitter . It includes an existing POTS line and a second pair installed for DSL access.
97-15300a RJ11 W all Jack or 8 Connecting to the DSL Access Wiring The Hotwire 5620 RTU connects to the local loop via wiring from the demarcation point to an RJ1 1 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack.
9 Installing the Hotwire 5620 R TU Place the Hotwire 5620 RTU on a flat surface with clearance for the rear connectors. Procedur e 1. Use the supplied RJ1 1 6-pin interface cable for the DSL connection. Insert one end of the cable into the jack labeled DSL.
10 2. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable into the jack labeled ETHERNET . Use a straight-through cable to connect the other end to an Ethernet hub. Do not connect to the optional Uplink connection with a straight-through cable (requires an Ethernet crossover cable).
11 3. Insert the supplied power cord’s round end into the jack labeled POWER. Plug the transformer into an AC outlet. 98-15836 PO WER ETHERNET DSL Hotwire RTU Po w e r Jack or T ransformer or The RTU hardware installation is now complete. When the power cord is installed, the RTU goes through a power-on self-test.
12 Status LEDs All of the LEDs turn on and off during the power-on self-test. After a successful self-test, the LEDs should appear as indicated in BOLD in the Condition column below . LED Condition Status PWR ON The RTU has power . ALM OFF ON No active alarms.
13 T roubleshooting LED Symptom Action All LEDs are on. If the LEDs remain on for more than ten minutes, the RTU is not functional. Unplug the unit and reapply power . If the ALM LED is still on, contact the service provider . ALM LED remains on. The power-on self-test may have failed.
98-15304-01 6-Pin RJ11 Plug DSL Cable Pin #1 Pin #6 14 Increasing the Number of End-User Systems A single end-user system is attached to the Hotwire 5620 RTU by using an Ethernet crossover cable. T o increase the number of end-user systems, connect all end-user systems to an Ethernet hub using a straight-through cable.
98-16055a 8-Pin Plug Ethernet Cable Pin #1 Pin #8 15 Ethernet interface connector uses an 8-pin, non-keyed modular plug. Use shielded twisted-pair CA T5 or better cables.
16 Optional R TU W all Placement The Hotwire 5620 RTU is designed for tabletop placement. The R TU can also be mounted on a wall. T o mount an RTU, you will need: - Three slotted-head #6 self-threadin.
17 R TU Hardware T emplate F ront (LEDs) 98-16171 5.43" 7.55" T o Bottom Hole.
18 Technical Specifications for Model 5620 R TU Item Specification * Height x Width x Depth 1.25 ″ x 6.00 ″ x 8.75 ″ (3.18 cm x 15.24 cm x 22.23 cm) Weight 1 lb.
19 ! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.
20 CE Marking When the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the following European Directives: Directive 73/23/EEC – Council Directiv.
21 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules. This compliance information statement pertains to the following products: T rade Name: Hotwire Model Number: 5620-A3-200 This device complies with Part 15 of the FCC Rules.
22 Government Requirements Certain governments require that instructions pertaining to connection to the telephone network be included in the installation and operation manual. Specific instructions are listed in the following sections. United States – Notice to Users of the T elephone Network 1.
23 7. The user is not authorized to repair or modify the equipment. 8. This equipment cannot be used on public coin service provided by the telephone company . Connection to Party Line Service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information.
24 W arranty , Sales, Service, and T raining Information Contact your local sales representative, service representative, or distributor directly for any help needed.
Een belangrijk punt na aankoop van elk apparaat Paradyne 5620-A2-GN11-30 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Paradyne 5620-A2-GN11-30 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Paradyne 5620-A2-GN11-30 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Paradyne 5620-A2-GN11-30 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Paradyne 5620-A2-GN11-30 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Paradyne 5620-A2-GN11-30 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Paradyne 5620-A2-GN11-30 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Paradyne 5620-A2-GN11-30 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.