Gebruiksaanwijzing /service van het product C2647M-B van de fabrikant Pelco
Ga naar pagina of 12
INSTALLATION C2647M-B (10/09) Hard Disk Drive Replacement Kit DVR5100 Series Hybrid V ideo Recorder.
2 C2647M-B (10/09) Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Models . . . . . . . . . . . . .
C2647M-B (10/09) 3 Introduction This manual describes how to inst all a replacement hard disk dr ive or upgrad e to a higher capacity hard disk drive in a DVR5100 Series hy brid video recorder (HVR).
4 C2647M-B (10/09) Installing the Hard Disk Drive Replacement Kit GETTING STARTED 1. Familiarize yourself with the instructi ons in this document. 2. V erify that you have all th e necessary parts and tools (refer to Parts and T ools on page 3). 3. If possible, export all essent ia l video before you install a new hard disk d r ive.
C2647M-B (10/09) 5 6. Use a Phillips screwdriver to remove the chassis cover (refer to Figure 1). a. Remove all 10 s crews from the DVR (four screws on ea ch side and two on the back). Se t aside the scre ws. Figure 1. Removing the Screws b. Slide the chassis cover back and up (refer to Figure 2).
6 C2647M-B (10/09) INSTALLING A HARD DISK DRIVE 1. Locate th e hard disk drive cage n ear the fron t of the unit . Figure 3. Locating the Hard Disk Drive Cage 2. T o remove a hard disk drive: a. Using a Phillips screwdriver , remove and set aside the two screws that secu re the hard disk drive cage to the bottom of t he chassis.
C2647M-B (10/09) 7 b. Lift up an d slide the cage out from under the retaine r bracket. T wo tabs along the bottom of the cage secure the cage to the bottom of the chassis. Figure 5. Removing the Hard Disk Drive Cage c. Remove the po wer and data ca bles from both drives in the cage.
8 C2647M-B (10/09) d. Using a Phillips screwdriver , remove an d set aside the four screws that secure the drive to the sides of the cage. Figure 7. Removing the Screws from the Hard Disk Drive in the Cage e. Slide the drive out of the cage. Avoid scratching the bottom of the drive against the metal sides or the bottom of the cage.
C2647M-B (10/09) 9 4. T o reinstall the hard disk dr ive cage in the chassis: a. Attach the po wer and data c ables to both drives. b. Place th e cage in the chassis and guide the tabs un der the retainer brac ket. Figure 9. Inserting the Hard Disk Drive Cage into the Chassis c.
10 C2647M-B (10/09) REASSEMBLING THE UNIT 1. Replace the chassis co ver using th e screws you re moved from the sides an d rear of the unit (refer to Figure 1 on page 5). 2. Reinstall the unit in a ra ck enclosure, if necessary , and then reconnect all cables and perip heral equipment you removed earlier .
PRODUCT W ARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or repl ace, without c harge, any mercha ndise proved defective in material or workmanship for a period of one year after the da te of shipment.
Pelco, Inc. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 29 2-1981 Fax +1 (559) 348-1120 www .
Een belangrijk punt na aankoop van elk apparaat Pelco C2647M-B (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelco C2647M-B heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelco C2647M-B vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelco C2647M-B leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelco C2647M-B krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelco C2647M-B bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelco C2647M-B kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelco C2647M-B . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.