Gebruiksaanwijzing /service van het product DD5L van de fabrikant Pelco
Ga naar pagina of 24
DD5L Series Dome Drive Installation/ Operation Manual C1471M (10/98) Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (80.
2 Pelco Manual C1471M (10/98) REVISION HISTOR Y Manual # Date Comments C1471CM 10/98 Original version. CONTENTS Section Page 1.0 GENERAL .................................................................................................. 3 1.1 IMPORT ANT SAFEGUARDS AND WARNINGS .
Pelco Manual C1471M (10/98) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Observe the following W ARNINGS before installing and using this product.
4 Pelco Manual C1471M (10/98) Figure 1. System Components (In-Ceiling Model Shown) BACK BOX DOME DRIVE LOWER DOME 1.2 UNP ACKING INSTRUCTIONS This box contains one dome drive and one Installation/Operation manual (C1471M). Inspect all parts carefully .
Pelco Manual C1471M (10/98) 5 2.0 DESCRIPTION Spectra ® Lite domes can do the following: • 360 ° pan rotation • preset positioning • +2 to -92 ° tilt • variable speed All Spectra ® Lite models include a color CCD camera with a 12X zoom lens and capability to focus when going to a preset position.
6 Pelco Manual C1471M (10/98) 3.0 INST ALLA TION 1. T urn on power to the back box. The red LED should light to indicate power . If the LED does not light, correct the trouble before proceeding. (Refer to Sec- tion 6.0, TROUBLESHOOTING, in manual C1487M.
Pelco Manual C1471M (10/98) 7 T able B. Switch Settings for SW2 – P-T ype Control NOTE: For Coaxitron ® controls, all switches on SW2 MUST be OFF . For D-type control systems, refer to T able C.
8 Pelco Manual C1471M (10/98) Receiver Address Switch Setting SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 1O N OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3O N O N OFF OFF OFF OFF.
Pelco Manual C1471M (10/98) 9 Receiver Address Switch Setting SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 57 ON OFF OFF ON ON ON OFF OFF 58 OFF ON OFF ON ON ON OFF OFF 59 ON ON OFF ON ON ON OFF OF.
10 Pelco Manual C1471M (10/98) Continued on next page 11 3 O N OFF OFF OFF ON ON ON OFF 11 4 OFF ON OFF OFF ON ON ON OFF 11 5 O N O N OFF OFF ON ON ON OFF 11 6 OFF OFF ON OFF ON ON ON OFF 11 7 O N OFF.
Pelco Manual C1471M (10/98) 11 Continued on next page 169 ON OFF OFF ON OFF ON OFF ON 170 OFF ON OFF ON OFF ON OFF ON 171 ON ON OFF ON OFF ON OFF ON 172 OFF OFF ON ON OFF ON OFF ON 173 ON OFF ON ON OF.
12 Pelco Manual C1471M (10/98) 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF OFF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON .
Pelco Manual C1471M (10/98) 13 4.0 OPERA TION The red LED in the back box interconnect door lights when power is turned on and the fan exhausts heat from inside the back box. If you have an outdoor pendant model with a heater , heater elements in the back box turn on at 70 ° F (21 ° C) and off at 85 ° F (29 ° C).
14 Pelco Manual C1471M (10/98) 4.3 ZOOM The Spectra ® Lite dome can magnify an object up to 12 times (12X of optical zoom). Zoom T elephoto - Press and hold down the Zoom T ele button until you have the picture you want. Zoom Wide - Press the Zoom Wide button to increase the field of view .
Pelco Manual C1471M (10/98) 15 4.6 P ARK If the dome does not receive any commands for a specified period, it goes to preset 1 and parks. The dome will not park if the time specified is zero or preset 1 has not been programmed. The default is zero minutes.
16 Pelco Manual C1471M (10/98) CM9500 1. Enter the number of the Spectra ® Lite camera and press the CAM key . 2. Press the SELECT key twice. 3. Highlight CAM in the Setup menu and press the SELECT key . 4. Highlight PRESET in the Camera menu and press the SELECT key .
Pelco Manual C1471M (10/98) 17 The following settings are not reset when the camera is reset: park time, auto flip disable, and limit stops. T urning off power to the dome does not reset the camera. Camera settings are retained in memory , and when power is restored, the settings are the same as when the camera was turned off.
18 Pelco Manual C1471M (10/98) 4.7.5 Shutter Speed There are nine electronic shutter speeds: Auto 1/100 1/120 1/500 1/1,000 1/2,000 1/4,000 1/10,000 1/30,000 In the Auto setting the camera controls the shutter speed automatically .
Pelco Manual C1471M (10/98) 19 R-B WHITE BALANCE - Move the joystick up or down to a value. As you change the value, you can see the color change on your monitor . Press the Iris Open button to select the value, or press the Iris Close button if you do not want to change the setting.
20 Pelco Manual C1471M (10/98) 3. Move the joystick up or down to cycle through the selections. Stop on the item you want to select. 4. SELECT – Press the Iris Open button to select your choice. CANCEL – Press the Iris Close button if you do not want to change the setting.
Pelco Manual C1471M (10/98) 21 Scan Limit Stops Refer to the documentation for your control system for programming presets, then do the following: 1. Make sure limit stops are turned ON (refer to Section 4.7.1 1.1), then exit the menu. 2. Push the joystick left until you reach the limit you want the camera to go to on the left.
22 Pelco Manual C1471M (10/98) 5.0 TROUBLESHOOTING Symptom: Unit or fan does not operate Refer to Section 6.0, TROUBLESHOOTING, in manual C1487M. 6.0 MAINTENANCE 6.1 DOME CLEANING Do not scratch the dome. Clean dome exterior and interior surfaces (except chrome or gold) with a nonabrasive liquid or spray cleaner/wax.
Pelco Manual C1471M (10/98) 23 7.0 SPECIFICA TIONS MECHANICAL Pan Movement: 360 ° continuous pan rotation Vertical Tilt: Unobstructed +2 ° to -92 ° Manual Pan Speed: 0.
24 Pelco Manual C1471M (10/98) 8.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1998, Pelco. All rights reserved.
Een belangrijk punt na aankoop van elk apparaat Pelco DD5L (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelco DD5L heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelco DD5L vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelco DD5L leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelco DD5L krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelco DD5L bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelco DD5L kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelco DD5L . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
