Gebruiksaanwijzing /service van het product IOP C309M-J van de fabrikant Pelco
Ga naar pagina of 50
ES30C/ES31C Series Esprit ® with IOP C309M-J (9/04) ® OPERA TION/PROGRAMMING.
2 C309M-J (9/04).
C309M-J (9/04) 3 CONTENTS Section Page IMPORT ANT SAFETY INSTRUCTIONS .................................................................................................. ............................................................................. 5 OPERA TION .
4 C309M-J (9/04) WHITE BALANCE .................................................................................................................. .................................................................................... 40 WIPER MODE ......
C309M-J (9/04) 5 IMPORT ANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
6 C309M-J (9/04) OPERA TION POWER-UP DISPLA Y When the system is powered up, the selected protocol, revision number , and other information is displayed on the monitor . For e xample, the screen might show the following information: The information displayed depends on the selected protocol (C, D, or P) and the menu selection for power - up mode.
C309M-J (9/04) 7 OPERA TING NOTES ENVIRONMENT AL RANGE The operating temperature ranges from a minimum of -50 ° F (-45 ° C) to a maximum of 122 ° F (50 ° C) for sustained system operation or 140 ° F (60 ° C) absolute maximum. The entire unit can de-ice and be operational in two hours from a temperature of -13 ° F (-25 ° C).
8 C309M-J (9/04) PA TTERNS The Esprit system can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt or lens command. Presets, flip, digital zoom, proportional pan, and turbo are not allowed in a pattern.
C309M-J (9/04) 9 PROGRAMMING - ES30C16/ES31C16 Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Sync Me.
10 C309M-J (9/04) PROGRAMMING - ES30C22/ES31C22 Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Sync M.
C309M-J (9/04) 11 PROGRAMMING - ES30CBW18/ES31CBW18 Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Syn.
12 C309M-J (9/04) PROGRAMMING ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 for Pelco’ s controllers varies according to the type of controller you are using.
C309M-J (9/04) 13 AUTO FOCUS MODE There are two auto focus modes: Auto – If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will place the focus in the manual mode. The system will return to auto focus if you pan or tilt the unit or do a zoom function.
14 C309M-J (9/04) AUTO IRIS The following are the settings for auto iris: Mode Level Peak To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu.
C309M-J (9/04) 15 AUTO IR LEVEL (MODELS ES30CBW18/ES31CBW18 ONL Y) The auto IR level is the light level at which the infrared filter switches IN or OUT . Following are the available settings for the Auto IR Level: DUSK (default) – approximately 6 lux (black-white) approximately 13 lux (color) DARK – approximately 0.
16 C309M-J (9/04) AUTO SHARPNESS The following settings are available for auto sharpness: On – Automatically sets the sharpness of the camera. Off – The sharpness of the camera needs to be manually set (refer to Sharpness ). To change the mode: 1.
C309M-J (9/04) 17 AZ/EL Az/El programs the horizontal display position of the Azimuth 1 /Elevation 2 label. NOTE: Az/El display is not available while you are programming or running a pattern. The following settings are available for the Az/El label: Off – Label is not displayed.
18 C309M-J (9/04) AZ/EL LINE Az/El Line controls the vertical display position of the Azimuth/Elevation label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen.
C309M-J (9/04) 19 AZIMUTH ZERO Azimuth is the pan angle from 0 ° to 359 ° . Azimuth zero is the programmed 0 ° point that is normally set to magnetic north. Once programmed, on-screen pan position (azimuth) and compass readings are based on the set azimuth zero point.
20 C309M-J (9/04) BACKLIGHT COMPENSA TION There are two backlight compensation modes: On – The system uses the center 10 percent of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is properly exposed.
C309M-J (9/04) 21 DIRECTION Direction programs the horizontal display position of the Direction label (N, NW , NE, …). NOTE: For direction to be accurate, the azimuth zero must be set to magnetic north. NOTE: Direction display is not available while you are programmming or running a pattern.
22 C309M-J (9/04) DIRECTION LINE Direction Line controls the vertical display position of the Direction label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen.
C309M-J (9/04) 23 DISPLA Y DURA TION Display Duration programs the duration the Az/El, Direction, and Zoom labels are displayed on the monitor . The available settings for display duration include the following: CONST ANT - The label is displayed continuously .
24 C309M-J (9/04) GAIN LIMIT The gain limit sets the maximum level for the automatic gain control. Increasing the level will increase the signal level and increase the noise level of the picture. To change the gain: 1. Program preset 95 (28). The main menu appears.
C309M-J (9/04) 25 IR FIL TER MODE (MODELS ES30CBW18/ES31CBW18 ONL Y) There are two settings for the IR filter mode: Auto – IR filter switches in and out automatically . IMPORT ANT : Automatic shutter speed must be set to Auto for the IR filter to operate automatically .
26 C309M-J (9/04) LIMIT STOPS NOTE: Limit stops are inactive while setting items in the program menu (e.g. azimuth zero, scan limits, manual pan limits). TURNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1. Program preset 95 (28). The main menu appears.
C309M-J (9/04) 27 LIMIT STOPS MENU The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu.
28 C309M-J (9/04) Scan Limit Stops When scan limit stops are set, the pan and tilt reverses direction during random, frame, or auto scanning when a limit stop is reached.
C309M-J (9/04) 29 LINE SYNCHRONIZA TION If cameras are out of phase with each other , they may produce what appears to be vertical roll when switching between cameras. There are two settings for line synchronization: On – Adjust the synchronization of the power line voltage so that it is in phase with other cameras.
30 C309M-J (9/04) LOWLIGHT LIMIT (MODELS ES30C22/ES31C22 AND ES30CBW18/ES31CBW18 ONL Y) This setting determines the maximum length of time the shutter will remain open automatically in low light conditions.
C309M-J (9/04) 31 P ARK TIME MINUTES This feature causes the system to park at preset 1 after a programmed number of minutes of control inactivity . The time can be set from 1 minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature.
32 C309M-J (9/04) PA TTERN LENGTH The Esprit can do the following: One full pattern - 1.5, 3, or 6 minutes long or T wo half patterns - .75, 1.5, or 3 minutes long This pattern can consist of any standard pan, tilt, or lens command. Presets, flip, and turbo are not allowed in a pattern.
C309M-J (9/04) 33 POWER-UP MODE This feature lets the dome resume a desired condition following power -up. The menu includes the following choices. • Default – On power -up, the system goes through a configuration cycle and stops at zero reference, showing “Configuration Done,” address, and mode settings on the screen.
34 C309M-J (9/04) PROPORTIONAL P AN There are two proportional pan modes: On – Enables the proportional pan mode. The amount of zoom controls the pan and tilt. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings.
C309M-J (9/04) 35 RESET CAMERA Default Setting <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Other> Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Resetting the camera returns the settings to their defaults.
36 C309M-J (9/04) SCAN SPEED The scan speed is adjustable from 1-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan. To change the scan speed: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Other .
C309M-J (9/04) 37 SHARPNESS Use the Sharpness setting to manually set the sharpness of the camera. To manually set the sharpness of the camera: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu.
38 C309M-J (9/04) SHUTTER SPEED There are several electronic shutter speed settings: Auto 1/2 1/4 1/8 1/15 1/30 1/60 1/120 1/180 1/250 1/500 1/1000 1/2000 1/4000 1/10,000 1/30,000 In the Auto setting the camera controls the shutter speed automatically .
C309M-J (9/04) 39 SPEED PROFILE This feature allows the operator to set the wind speed conditions for the location of the Esprit system. Y ou can set two wind speed profiles of 50 mph or 90 mph in which the system will remain operational. In both settings, the pan speed will be a maximum of 40 degrees per second.
40 C309M-J (9/04) WHITE BALANCE The settings for white balance are as follows: Auto white bal R Gain B Gain To change the white balance settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu.
C309M-J (9/04) 41 WIPER MODE There are three wiper settings: Wiper Mode Wiper Dwell Wiper T ime To change the wiper settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Wiper . 3. Press the Iris Open button to enter the Wiper menu.
42 C309M-J (9/04) The Esprit system features onscreen programmable zone blanking. This feature lets you define any zone as blanked for video (viewing/ recording).
C309M-J (9/04) 43 ZOOM Zoom programs the horizontal display position of the Zoom label. The following settings are available for the Zoom label: Off – Label is not displayed. Left – Label is displayed on the left-hand side of the screen. Center (default) – Label is displayed in the center of the screen.
44 C309M-J (9/04) ZOOM LIMIT ES30C16/ES31C16 - 16X optical zoom and 10X electronic zoom, can be set for 16X, 32X, 64X, 128X, or 160X. ES30C22/ES31C22 - 22X optical zoom and 10X electronic zoom, can be set for 22X, 32X, 88X, 176X, or 220X. ES30CBW18/ES31CBW18 - 23X optical zoom and 10X electronic zoom, can be set for 23X, 32X, 92X, 184X or 230X.
C309M-J (9/04) 45 ZOOM LINE Zoom Line controls the vertical display position of the Zoom label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting.
46 C309M-J (9/04) SPECIFICA TIONS ELECTRICAL Input V oltage: 24, 120, or 230 V AC, 50/60 Hz; switch selectable for 120/230 VAC inputs. Reset featur e enabled when power becomes unstable or interrupted.
C309M-J (9/04) 47 Sensitivity ES30C16/ES31C16: 0.05 lux at 1/2-second shutter speed (NTSC) 0.05 lux at 1/1.5-second shutter speed (P AL) ES30C22/ES31C22: 0.02 lux at 1/2-second shutter speed (NTSC) 0.02 lux at 1/1.5-second shutter speed (P AL) ES30CBW18/ES31CBW18: 0.
.
REVISION HISTORY Manual # Date Comments C309M 9/00 Original version. C309M-A 12/00 Added information on “Pan Limit” message per ECO #00-6635. C309M-B 6/01 Added information on zone blanking. C309M-C 9/02 Camera modifications. C309M-D 6/03 Added Az/El/Direction menu per ECO #03-8861.
W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
Een belangrijk punt na aankoop van elk apparaat Pelco IOP C309M-J (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelco IOP C309M-J heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelco IOP C309M-J vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelco IOP C309M-J leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelco IOP C309M-J krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelco IOP C309M-J bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelco IOP C309M-J kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelco IOP C309M-J . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
